Sorption kinetics and its effects on retention and leaching.

Sorption of pesticides to substrates used in biopurification systems is important as it controls the system's efficiency. Ideally, pesticide sorption should occur fast so that leaching of the pesticide in the biopurification system is minimized. Although modeling of pesticide transport commonly assumes equilibrium, this may not always be true in practice. Sorption kinetics have to be taken into account. This study investigated the batch sorption kinetics of linuron, isoproturon, metalaxyl, isoxaben and lenacil on substrates commonly used in a biopurification system, i.e. cow manure, straw, willow chopping, sandy loam soil, coconut chips, garden waste compost and peat mix. The first-order sorption kinetics model was fitted to the observed pesticide concentrations versus time resulting in an estimated kinetic rate constant alpha. Sorption appeared to be fast for the pesticides linuron and isoxaben, pesticides which were classified as immobile, while less mobile pesticides displayed an overall slower sorption. However, the substrate does not seem to be the main parameter influencing the sorption kinetics. Coconut chips, which is a substrate with a high organic matter content showed slow sorption for most of the pesticides. The effect of different estimated alpha values on the breakthrough of pesticides through a biopurification system was evaluated using the HYDRUS 1D model. Significant differences in leaching behavior were observed as a result of the obtained differences in sorption kinetics.     

Influence of pH on pesticide sorption by soil containing wheat residue-derived char

Field burning of crop residues incorporates resulting chars into soil and may thus influence the environmental fate of pesticides in the soil. This study evaluated the influence of pH on the sorption of diuron, bromoxynil, and ametryne by a soil in the presence and absence of a wheat residue-derived char. The sorption was measured at pHs approximately 3.0 and approximately 7.0. Wheat char was found to be a highly effective sorbent for the pesticides, and its presence (1% by weight) in soil contributed >70% to the pesticide sorption (with one exception). The sorption of diuron was not influenced by pH, due to its electroneutrality. Bromoxynil becomes dissociated at high pHs to form anionic species. Its sorption by soil and wheat char was lower at pH approximately 7.0 than at pH approximately 3.0, probably due to reduced partition of the anionic species of bromoxynil into soil organic matter and its weak interaction with the carbon surface of the char. Ametryne in its molecular form at pH approximately 7.0 was sorbed by char-amended soil via partitioning into soil organic matter and interaction with the carbon surface of the char. Protonated ametryne at pH approximately 3.0 was substantially sorbed by soil primarily via electrostatic forces. Sorption of protonated ametryne by wheat char was also significant, likely due not only to the interaction with the carbon surface but also to interactions with hydrated silica and surface functional groups of the char. Sorption of ametryne by char-amended soil at pH approximately 3.0 was thus influenced by both the soil and the char. Environmental conditions may thus significantly influence the sorption and behavior of pesticides in agricultural soils containing crop residue-derived chars.     

Acetamiprid, carbendazim, diuron and thiamethoxam sorption in two Brazilian tropical soils

Sorption of acetamiprid ((E)-N1-[(6-chloro-3-pyridyl)methyl]-N2-cyano-N1-methylacetamidine), carbendazim (methyl benzimidazol-2-ylcarbamate), diuron (N-(3,4-dichlorophenyl)-N, N-dimethyl urea) and thiamethoxam (3-(2-chloro-thiazol-5-ylmethyl)-5-methyl-[1,3,5]oxadiazinan-4-ylidene-N-nitroamine) was evaluated in two Brazilian tropical soils, Oxisol and Entisol, from Primavera do Leste region, Mato Grosso State, Brazil. To describe the sorption process, batch experiments were carried out. Linear and Freundlich isotherm models were used to calculate the K(d) and K(f) coefficients from experimental data. The K(d) values were utilized to calculate the partition coefficient normalized to soil organic carbon (K(oc)). For the pesticides acetamiprid, carbendazim, diuron and thiamenthoxan the K(oc) (mL g(- 1)) values ranged in both soils from 98 - 3235, 1024 - 2644, 145 - 2631 and 104 - 2877, respectively. From the studied pesticides, only carbendazim presented correlation (r(2) = 0.82 and p < 0.01) with soil organic carbon (OC) content. Acetamiprid and thiamethoxam showed low sorption coefficients, representing a high risk of surface and ground water contamination.     

Evaluation of sorption-desorption processes for metalaxyl in natural and artificial soils

The main process controlling soil-pesticide interaction is the sorption-desorption as influenced by active soil surfaces. The sorption phenomena can influence translocation, volatility, persistence and bioactivity of a pesticide in soil. The present investigation was conducted on natural and artificial soils in order to enumerate the effect of soil components such as montmorillonite and ferrihydrite on the sorption behaviour of the fungicide metalaxyl and if sorption-desorption of the chiral pesticide affects the enantiomeric ratio. The sorption-desorption characteristics of metalaxyl were investigated by batch equilibration technique in a natural soil, two artificial soils, and in pure montmorillonite and ferrihydrite. After extraction, pesticide residues were analyzed by conventional and chiral chromatography using tandem mass spectrometry. A K_dSorp (2.3–6.5) suggests low level sorption of metalaxyl with an appreciable risk of run-off and leaching. Thus, metalaxyl poses a threat to surface and ground water contamination. Furthermore, desorption tests revealed a hysteretic effect (H ≤ 0.8) in natural and artificial soils. Significant amount of metalaxyl was found tightly bound to the adsorbents without desorbing readily after desorption cycle. Desorption of 22–56% of the total amount of the retained metalaxyl was determined. This study reveals that an artificial soil derived from different soil constituents can be used to assess their influence on sorption/desorption processes. The present investigation showed that both montmorillonite and ferrihydrite play a significant role in the sorption of metalaxyl. The sorption doesn't influence the enantiomeric ratio of racemic metalaxyl.     

Time dependent sorption behavior of dinotefuran,imidacloprid and thiamethoxam

Dinetofuran (DNT), imidacloprid (IMD) and thiamethoxam (THM) are among the neonicotinoid insecticides widely used for managing insect pests of agricultural and veterinary importance. Environmental occurrence of neonicotinoid in post-application scenario poses unknown issues to human health and ecology. A sorption kinetic study provides much needed information on physico-chemical interaction of neonicotinoid with soil material. In this research study, time-dependent sorption behavior of DNT, IMD and THM in vineyard soil was studied. Sorption kinetics studies were conducted over a period of 96 hours with sampling duration varying from 0, 2, 4, 8, 12, 24, 60 and 96 hours. All three neonicotinoids exhibited very low sorption potential for the soil investigated. Overall percent sorption for all three neonicotinoids was below 20.04 ± 2.03% with highest percent sorption being observed for IMD followed by DNT and THM. All three neonicotinoids are highly soluble with solubility increasing with IMD < THM < DNT. Although, DNT has the highest solubility among all three neonicotinoids investigated, it exhibited higher percent sorption compared to THM, indicating factors other than solubility influenced the sorption kinetics. Low sorption potential of neonicotinoids indicates greater leaching potential with regard to groundwater and surface water contamination.     

Sorptive behavior of the phenylamide fungicides,mefenoxam and metalaxyl,and their acid metabolite in typical Cameroonian and German soils

Laboratory soil sorption experiments were conducted on mefenoxam, formulated metalaxyl (F-metalaxyl), pure metalaxyl (P-metalaxyl) and metalaxyl acid metabolite to elucidate differences in their sorptive behaviour on typical Cameroonian forest soil (sand clay loam, pH 4.8 and 3.01% OC) and German soil (sandy loam, pH 7.2, 1.69% OC) using a batch equilibrium method. The data obtained on all test chemicals conformed to linear and Freundlich adsorption isotherms. The Langmuir equation failed to describe the sorption of the substances tested. All substances were adsorbed to a greater extent by the Cameroonian soil. The average percentage adsorptions for mefenoxam, F-metalaxyl, P-metalaxyl and the acid metabolite on the Cameroonian soil were 27.8%, 28.3%, 31.8% and 46.8% respectively while for the German soil they were 21.7%, 21.5%, 24.7% and 9.8% respectively. The KD and KF parameters and the Freundlich exponential term (1/n) were low, indicating that the interactions between soil particles and the fungicides were weak. The sorption parameters were lower in the German soil. P-metalaxyl exhibited a higher adsorption capacity than F-metalaxyl in both soils. Mefenoxam and F-metalaxyl exhibited similar sorption parameters in soils, whereas those of P-metalaxyl and acid metabolite differed. Differences observed in the adsorption between the two soils could be attributed to their properties. Desorption studies revealed that the adsorbed fungicides were not firmly retained by soil particles and their adsorption was reversible. Desorption of adsorbed mefenoxam, P-metalaxyl and of the acid metabolite from German soil was almost completely reversible with percentage desorption rates of more than 91.0%, whereas the rate for F-metalaxyl was 74.1%. All compounds exhibited some resistance to desorption from the Cameroonian soil, with percentage desorption rates less than 77.0%. Therefore if degradation in the soil is slow the fungicides described have a potential to leach to lower soil horizons.     

Enhanced retention of linuron, alachlor and metalaxyl in sandy soil columns intercalated with wood barriers

A study has been made of the effect a reactive barrier made of pine (softwood) or oak (hardwood) wood intercalated in a sandy soil column has on the retention of linuron, alachlor and metalaxyl (pesticides with contrasting physicochemical characteristics). The leaching of pesticides has been carried out under a saturated flow regime and breakthrough curves (BTCs) have been obtained at flow rates of 1 mL min⁻¹ (all pesticides) and 3 mL min⁻¹ (linuron). The cumulative curves in the unmodified soil indicate a leaching of pesticides >80% of the total amount of compound added. After barrier intercalation, linuron leaching decreases significantly and a modification of the leaching kinetics of alachlor and metalaxyl has been observed. The theoretical R factors increased ∼2.6-3.3, 1.2-1.6-fold, and 1.4-1.7-fold and the concentration of the maximum peak decreased ∼6-12-fold, 2-4-fold and 1.2-2-fold for linuron, alachlor and metalaxyl, respectively. When considering the three pesticides, significant correlations have been found between the theoretical retardation factor (R) and the pore volume corresponding to the maximum peaks of the BTCs (r = 0.77; p < 0.05) or the total volume leached (r = −0.78; p < 0.05). The results reveal the efficacy of reactive wood barriers to decrease the leaching of pesticides from point sources of pollution depends on the type of wood, the hydrophobicity of the pesticide and the adopted water flow rate. Pine was more effective than oak in decreasing the leaching of hydrophobic pesticide linuron or in decreasing the maximum peak concentration of the less hydrophobic pesticides in soils. Efficacy of these wood barriers was limited for the least hydrophobic pesticide metalaxyl.     

Controlled release and retarded leaching of pesticides by encapsulating in carboxymethyl chitosan /bentonite composite gel

A novel composite gel composed of carboxymethyl-chitosan (CM-chit) and bentonite (H-bent) was used as the carrier for encapsulating atrazine and imidacloprid to control their release in water and retard their leaching in soil. Strong interactions between CM-chit and H-bent in the composite were confirmed by FT-IR, and good dispersion of pesticides in the carrier was observed by SEM. According to the results of release experiments in water, the CM-chit/H-bent composite carrier showed double advantages of both encapsulation by the polymer and sorption by the bentonite. The time taken for 50 % of active ingredients to be released, t??, was prolonged to 572 h for atrazine and 24 h for imidacloprid, respectively. The difference between the two pesticides on release behavior was related to their hydrophobicity and water solubility. Leaching experiments through a soil layer showed that this novel carrier reduced the amount of pesticides available for leaching, and would be useful for diminishing the environmental pollution of pesticides.     

Degradation of cyprodinil, fludioxonil, cyfluthrin and pymetrozine on lettuce after different application methods

Degradation of two fungicides (cyprodinil and fludioxonil) and two insecticides (cyfluthrin and pymetrozine) applied on iceberg and romaine lettuce under field conditions with different methods (portable mistblower and chemigation) was studied field data showed that both distribution methods and lettuce cultivar affect the degradation trends of examined pesticides. In these trials the residues of all active ingredients after pre-harvest time were less than fifty's maximum residue levels; the values in the romaine cultivar were generally higher than those in iceberg lettuce. After pre-harvest time residues of pesticides applied on romaine lettuce by portable motor sprayer were always higher than those obtained by the chemigation system.     

Degradation of cyprodinil,fludioxonil, cyfluthrin and pymetrozine on lettuce after different application methods

Degradation of two fungicides (cyprodinil and fludioxonil) and two insecticides (cyfluthrin and pymetrozine) applied on iceberg and romaine lettuce under field conditions with different methods (portable mistblower and chemigation) was studied field data showed that both distribution methods and lettuce cultivar affect the degradation trends of examined pesticides. In these trials the residues of all active ingredients after pre-harvest time were less than fifty's maximum residue levels; the values in the romaine cultivar were generally higher than those in iceberg lettuce. After pre-harvest time residues of pesticides applied on romaine lettuce by portable motor sprayer were always higher than those obtained by the chemigation system.     

Transport and degradation of pesticides in a biopurification system under variable flux, part I: A microcosm study

The efficiency of a biopurification system, developed to treat pesticide contaminated water, is to a large extent determined by the chemical and hydraulic load. Insight into the behaviour of pesticides under different fluxes is necessary. The behaviour of metalaxyl, bentazone, linuron, isoproturon and metamitron was studied under three different fluxes with or without the presence of pesticide-primed soil in column experiments. Due to the time-dependent sorption process, retention of the pesticides with intermediate mobility was significantly influenced by the flux. The higher the flux, the slower pesticides will be sorbed, which resulted in a lower retention. Degradation of the intermediate mobile pesticides was also submissive to variations in flux. An increase in flux, led to a decrease in retention, which in turn decreased the opportunity time for biodegradation. Finally, the presence of pesticide-primed soil was only beneficial for the degradation of metalaxyl.     

Distribution of organophosphate insecticides in a Thai biomass-water system

Sorption and leaching of the organophosphate (OP) pesticides chlorpyrifos, profenofos, methyl parathion and malathion were investigated with four different types of biomass: coconut husk, rice husk, peat moss and peanut shell. Organic carbon contents of the biomass were in the range of 35.4–45.4%. Sorption studies were carried out by the batch (equilibrium) method at 4 different OP spike concentrations and at pH 3–7. Sorption isotherms conformed to a linear Freundlich equation and the Freundlich constant or sorption coefficient (K_D) confirmed that biomass organic carbon content was the principal sorbent factor affecting OP sorption. For a given sorbent, correlation of the extent of sorption with sorbate chemical properties was examined. Column leaching experiments involving different masses of coconut husk and peanut shell pre-spiked with OPs at the level equivalent to actual spraying concentrations in some Thai tangerine orchards were conducted. These experiments included repeated spikings and leaching. A water flow rate of 20 mL min^?1 was employed corresponding to the current average watering regime. Retardation and biodegradation with these sorbents were also examined.     

Distribution of organophosphate insecticides in a Thai biomass-water system

Sorption and leaching of the organophosphate (OP) pesticides chlorpyrifos, profenofos, methyl parathion and malathion were investigated with four different types of biomass: coconut husk, rice husk, peat moss and peanut shell. Organic carbon contents of the biomass were in the range of 35.4-45.4%. Sorption studies were carried out by the batch (equilibrium) method at 4 different OP spike concentrations and at pH 3-7. Sorption isotherms conformed to a linear Freundlich equation and the Freundlich constant or sorption coefficient (KD) confirmed that biomass organic carbon content was the principal sorbent factor affecting OP sorption. For a given sorbent, correlation of the extent of sorption with sorbate chemical properties was examined. Column leaching experiments involving different masses of coconut husk and peanut shell pre-spiked with OPs at the level equivalent to actual spraying concentrations in some Thai tangerine orchards were conducted. These experiments included repeated spikings and leaching. A water flow rate of 20 mL min(-1) was employed corresponding to the current average watering regime. Retardation and biodegradation with these sorbents were also examined.     

Influence of biotic and abiotic factors on dissipating metalaxyl in soil.

Under laboratory condition, dissipation of metalaxyl in sterile and non-sterile soils, its sorption behaviour and fate in presence of light have been studied. The half-life value of metalaxyl was found in the range of 36-73 d in non-sterile soil. 5.3-14.7% dissipation was observed due to abiotic factors other than light. Metalaxyl was found photostable in soil showing half-life of 188- 502 h under simulated sunlight. In adsorption study, a non-linear relationship between concentration of metalaxyl and its adsorption into soils was observed. Estimated koc value increased as organic carbon content decreased. Adsorption and desorption kD values ranged between 53.5 and 151.1.     

Effects of soil composition on solid phase microextraction determination of triazine and organophosphorus pesticides

The influence of organic matter and clay contents on headspace solid phase microextraction (HS-SPME) determination of triazine and organophosphorus pesticides in different soils was studied. The results of the study showed that content of soil organic matter dominantly participated in sorption of triazines (simazine, atrazine and prometryn) to soil, while sorption of organophosphorus pesticides (phorate and tebupirimfos) could not be explained only by contents of dominant soil sorption components (soil organic matter and clay). Sorption of all pesticides studied to different soil types was similar at their lower concentrations while the influence of soil composition was expressed at higher concentration levels. Except for phorate, the obtained sorption trends were different from those obtained by direct SPME mode (DM-SPME) and exhaustive liquid-solid extraction (LSE) method. These results indicated that most likely co-extractants from the analyzed medium complicated evaporation and diffusion of the pesticides to the PDMS fiber during HS-SPME sampling.     

Adsorption of chlorpyrifos,penconazole and metalaxyl from aqueous solution by modified clays

Sorption of three pesticides (chlorpyrifos, metalaxyl and penconazole) has been measured on a commercial clay montmorillonite and on the same mineral modified with either of two cationic-surfactant micelles. Both micelle–clay complexes, commercial names Cloisite 20A and Cloisite 30B, showed a good capacity to sorb all three pesticides from water, whereas their sorption on the natural montmorillonite was not described by an isotherm. Modelling sorption on both micelle–clay complexes showed that the Freundlich sorption constant (K _F) was higher for chlorpyrifos on Cloisite 20A (K _F = 7.76) than on Cloisite 30B (K _F = 5.91), whereas the sorption of metalaxyl was stronger on Cloisite 30B (K _F = 1.07) than on Cloisite 20A (K _F = 0.57). Moreover the micelle–clay complex Cloisite 20A also showed a good affinity for penconazole, the maximum quantity adsorbed (q _m) of 6.33 mg g^?1 being 45% more than that on Cloisite 30B. Single-batch adsorption of each pesticide onto both micelle–clay complexes was studied using the Freundlich isotherm for chlorpyrifos and metalaxyl and the Langmuir isotherm for penconazole. The Cloisite 20A micelle–clay complex was predicted to require 23% less adsorbent to treat certain volumes of wastewater containing 30 mg L^?1 chlorpyrifos, 43% more to treat metalaxyl similarly and 57% less to treat penconazole compared with Cloisite 30B.     

Controlled release and retarded leaching of pesticides by encapsulating in carboxymethyl chitosan /bentonite composite gel

A novel composite gel composed of carboxymethyl-chitosan (CM-chit) and bentonite (H-bent) was used as the carrier for encapsulating atrazine and imidacloprid to control their release in water and retard their leaching in soil. Strong interactions between CM-chit and H-bent in the composite were confirmed by FT-IR, and good dispersion of pesticides in the carrier was observed by SEM. According to the results of release experiments in water, the CM-chit/H-bent composite carrier showed double advantages of both encapsulation by the polymer and sorption by the bentonite. The time taken for 50 % of active ingredients to be released, t ₅₀, was prolonged to 572 h for atrazine and 24 h for imidacloprid, respectively. The difference between the two pesticides on release behavior was related to their hydrophobicity and water solubility. Leaching experiments through a soil layer showed that this novel carrier reduced the amount of pesticides available for leaching, and would be useful for diminishing the environmental pollution of pesticides.     

Acetamiprid,carbendazim, diuron and thiamethoxam sorption in two Brazilian tropical soils

Sorption of acetamiprid ((E)-N1-[(6-chloro-3-pyridyl)methyl]-N2-cyano-N1-methylacetamidine), carbendazim (methyl benzimidazol-2-ylcarbamate), diuron (N-(3,4-dichlorophenyl)-N, N-dimethyl urea) and thiamethoxam (3-(2-chloro-thiazol-5-ylmethyl)-5-methyl-[1,3,5]oxadiazinan-4-ylidene-N-nitroamine) was evaluated in two Brazilian tropical soils, Oxisol and Entisol, from Primavera do Leste region, Mato Grosso State, Brazil. To describe the sorption process, batch experiments were carried out. Linear and Freundlich isotherm models were used to calculate the K _d and K _f coefficients from experimental data. The K _d values were utilized to calculate the partition coefficient normalized to soil organic carbon (K _oc ). For the pesticides acetamiprid, carbendazim, diuron and thiamenthoxan the K _oc (mL g^{? 1}) values ranged in both soils from 98 – 3235, 1024 – 2644, 145 – 2631 and 104 – 2877, respectively. From the studied pesticides, only carbendazim presented correlation (r² = 0.82 and p < 0.01) with soil organic carbon (OC) content. Acetamiprid and thiamethoxam showed low sorption coefficients, representing a high risk of surface and ground water contamination.     

The effects of particle size, organic matter content, crop residues and dissolved organic matter on the sorption kinetics of atrazine and isoproturon by clay soil

Reliable predictions of the fate and behaviour of pesticides in soils is dependent on the use of accurate ‘equilibrium’ sorption constants and/or rate coefficients. However, the sensitivity of these parameters to changes in the physicochemical characteristics of soil solids and interstitial solutions remains poorly understood. Here, we investigate the effects of soil organic matter content, particle size distribution, dissolved organic matter and the presence of crop residues (wheat straw and ash) on the sorption of the herbicides atrazine and isoproturon by a clay soil. Sorption K_d's derived from batch ‘equilibrium’ studies for both atrazine and isoproturon by <2 mm clay soil were approximately 3.5 L/kg. The similarity of K_oc's for isoproturon sorption by the <2 mm clay soil and <2 mm clay soil oxidised with hydrogen peroxide suggested that the sorption of this herbicide was strongly influenced by soil organic matter. By contrast, K_oc's for atrazine sorption by oxidised soil were three times greater than those for <2 mm soil, indicating that the soil mineral components might have affected sorption of this herbicide. No significant differences between the sorption of either herbicide by <2 mm clay soil and (i) <250 μm clay soil, (ii) clay soil mixed with wheat straw or ash at ratios similar to those observed under field conditions, (iii) <2 mm clay soil in the presence of dissolved organic matter as opposed to organic free water, were observed.     

Long-term tillage effects on soil metolachlor sorption and desorption behavior

Sorption and desorption are two important processes that influence the amount of pesticides retained by soils. However, the detailed sorption mechanisms as influenced by soil tillage management are unclear. This study examined the sorption and desorption characteristics of metolachlor [2-chloro-N-(2-ethyl-6-methyphenyl)-N-(2-methoxy-1-methylethyl)-acetamide] using the soil samples collected from the long-term conservation tillage (CnT) and conventional tillage (CT) research plots established in 1979 in Darlinton, SC. Humic acid (HA) and humin were extracted from the soils and used in the sorption experiments along with the whole soil samples. The sorption experiments were conducted using a batch-equilibration method. Three sequential desorption rinses were carried out following the sorption experiments. By comparing metolachlor sorption and desorption results we observed hysteresis for all soil samples and their organic matter fractions. Sorption nonlinearity (N) and hysteresis were dependent on the structure and composition of soil organic matter (SOM), e.g., Freundlich isotherm exponents (N) of HA and humin from CnT were higher than those of CT treatment, which may be related to high aromaticity of SOM fractions in CT treatment. Sorption capacity (K'f) was positively correlated with soil organic carbon (SOC) content. These results show that long-term tillage management can greatly affect metolachlor sorption and desorption behavior probably by qualitative differences in the structural characteristics of the humic substances.