EVA树脂粉尘/甲烷/空气杂混物爆炸特性

在20 L爆炸实验装置中,开展了3种不同中值粒径的EVA树脂粉尘/甲烷/空气所组成的杂混物爆炸特性研究,探究了甲烷浓度对粉尘爆炸下限、最大爆炸压力的影响。结果表明,尽管添加的甲烷气体浓度低于爆炸下限,仍使得粉尘爆炸下限得以降低,粒径较大的EVA III粉尘,当甲烷体积分数为1%时,爆炸下限降低约25%;粒径较小的EVA I粉尘,当混入甲烷体积分数为4%时,爆炸下限则降低80%;甲烷体积分数每增加1%,可燃粉尘最大爆炸压力上升约10%,但对于粒径较小的EVA I粉尘,当甲烷体积分数为4%时,最大爆炸压力的上升呈现突变趋势,上升近50%。     

Explosibility of micron- and nano-size titanium powders

Explosibility of micron- and nano-titanium was determined and compared according to explosion severity and likelihood using standard dust explosion equipment. ASTM methods were followed using a Siwek 20-L explosion chamber, MIKE 3 apparatus and BAM oven. The explosibility parameters investigated for both size ranges of titanium include explosion severity (maximum explosion pressure (P_max) and size-normalized maximum rate of pressure rise (K_St)) and explosion likelihood (minimum explosible concentration (MEC), minimum ignition energy (MIE) and minimum ignition temperature (MIT)). Titanium particle sizes were ?100 mesh (<150 μm), ?325 mesh (<45 μm), ≤20 μm, 150 nm, 60–80 nm, and 40–60 nm. The results show a significant increase in explosion severity as the particle size decreases from ?100 mesh with an apparent plateau being reached at ?325 mesh and ≤20 μm. Micron-size explosion severity could not be compared with that for nano-titanium due to pre-ignition of the nano-powder in the 20-L chamber. The likelihood of an explosion increases significantly as the particle size decreases into the nano range. Nano-titanium is very sensitive and can self-ignite under the appropriate conditions. The explosive properties of the nano-titanium can be suppressed by adding nano-titanium dioxide to the dust mixture. Safety precautions and procedures for the nano-titanium are also discussed.     

Niacin,lycopodium and polyethylene powder explosibility in 20-L and 1-m3 test chambers

An experimental program has been undertaken to investigate the explosibility of selected organic dusts. The work is part of a larger research project aimed at examination of a category of combustible dusts known as marginally explosible. These are materials that appear to explode in laboratory-scale test chambers, but which may not produce appreciable overpressures and rates of pressure rise in intermediate-scale chambers. Recent work by other researchers has also demonstrated that for some materials, the reverse occurs – i.e., values of explosion parameters are higher in a 1-m³ chamber than one with a volume of 20 L. Uncertainties can therefore arise in the design of dust explosion risk reduction measures.The following materials were tested in the current work: niacin, lycopodium and polyethylene, all of which are well-known to be combustible and which cover a relatively wide range of explosion consequence severity. The concept of marginal explosibility was incorporated by testing both fine and coarse fractions of polyethylene. Experiments were conducted at Dalhousie University using the following equipment: (i) Siwek 20-L explosion chamber for determination of maximum explosion pressure (P_max), volume-normalized maximum rate of pressure rise (K_St), and minimum explosible concentration (MEC), (ii) MIKE 3 apparatus for determination of minimum ignition energy (MIE), and (iii) BAM oven for determination of minimum ignition temperature (MIT). Testing was also conducted at Fauske & Associates, LLC using a 1-m³ explosion chamber for determination of P_max, K_St and MEC. All equipment were calibrated against reference dusts, and relevant ASTM methodologies were followed in all tests.The explosion data followed known trends in accordance with relevant physical and chemical phenomena. For example, P_max and K_St values for the fine sample of polyethylene were higher than those for the coarse sample because of the decrease in particle size. MEC values for all samples were comparable in both the 20-L and 1-m³ chambers. P_max and K_St values compared favorably in the different size vessels except for the coarse polyethylene sample. In this case, K_St determined in a volume of 1 m³ was significantly higher than the value from 20-L testing. The fact that the 20-L K_St was low (23 bar m/s) does not indicate marginal explosibility of the coarse polyethylene. This sample is clearly explosible as evidenced by the measured values of MEC, MIE, MIT, and 1-m³ K_St (at both 550 and 600 ms ignition delay times).     

Risk assessment method of polyethylene dust explosion based on explosion parameters

The explosion characteristic parameters of polyethylene dust were systematically investigated. The variations in the maximum explosion pressure (P_max), explosion index (K_st), minimum ignition energy (MIE), minimum ignition temperature (MIT), and minimum explosion concentration (MEC) of dust samples with different particle sizes were obtained. Using experimental data, a two-dimensional matrix analysis method was applied to classify the dust explosion severity based on P_max and K_st. Then, a three-dimensional matrix was used to categorize the dust explosion sensitivity based on three factors: MIE, MIT, and MEC. Finally, a two-dimensional matrix model of dust explosion risk assessment was established considering the severity and sensitivity. The model was used to evaluate the explosion risk of polyethylene dust samples with different particle sizes. It was found that the risk level of dust explosion increased with decreasing particle size, which was consistent with the actual results. The risk assessment method can provide a scientific basis for dust explosion prevention in the production of polyethylene.     

Experimental study of the influence of particle size on Minimum Explosible Concentration of sulfur dust

Despite the extensive use of sulfur in the industry, very little information is available in the literature on its key dust explosion properties. The work presented in this paper contributes to filling the current knowledge gaps on sulfur dust explosion properties and focuses on the experimental determination of the MEC of sulfur dust using a Modified Hartmann Tube and a 20 L dust explosion sphere. First, the MEC of sulfur dust samples collected at a sulfur production facility from areas prone to the generation of fine sulfur dust was measured. The results showed that these sulfur dust samples are fine enough to cause dust explosions with 55 ± 5< MEC <105 ± 5 g/m³. Second, the influence of the particle size of sulfur dust was investigated with both equipment. The use of the Modified Hartmann Tube for MEC determination showed that the MEC increases with increasing particle size in the particle size range of 0–2000 μm. Unlike the Modified Hartmann Tube, MEC experiments done in the 20 L Sphere did not allow the quantification of the influence of the particle size on the MEC. These results were explained by the phenomenon of particle breakage induced by the 20 L Sphere's dispersion mechanism. Additional experiments with the 20 L sphere confirmed the particle breakage of sulfur dust particles and showed that it is inversely proportional to dust concentration and proportional to the dust's original particle size distribution.     

A critical evaluation of combustible/explosible dust testing methods – Part 1

Tests were conducted by the Center for Agricultural Air Quality Engineering and Science (CAAQES) and by Safety Consulting Engineers Inc. (SCE) to determine if dust found in cotton gins (gin dust) would serve as fuel for dust explosions. In other words, is gin dust explosible? The laboratory tests used by CAAQES and SCE are very different. SCE used a totally enclosed 20 liter (L) chamber, flame from a 10,000 J (10 kJ) ignition source, reported that gin dust was a class ‘A’ explosible dust. CAAQES used a 28.3-L (1 ft³) chamber with diaphragm, a stationary coil as the igniter, video and pressure recordings of each test and concluded that gin dust was not explosible. SCE followed the protocols specified by ASTM E1226 and E1515. The only indicator used to determine whether a deflagration occurred during a test was pressure. If the pressure rise exceeded one bar gage (g) in a 20-L chamber test with a flame from a 10 kJ energy source as the igniter, it was assumed that a deflagration occurred in the chamber and the dust was classified as explosible (ASTM E1226-05, 2005). The CAAQES criterion for determining if a dust was explosible consisted of determining the minimum explosive concentration (MEC). If the MEC existed using the CAAQES test system, it was explosible! The criteria used with the CAAQES method for determining the MEC was to test concentrations starting at concentrations above the MEC and lowering the concentrations until at least one of the three tests at that concentration failed to result in a deflagration. The indicators of a deflagration were (1) bursting of a diaphragm, (2) flame front leaving the chamber and (3) characteristic pressure vs. time curve.It was concluded that the ASTM method of using only pressure as the indicator of a deflagration in a totally enclosed chamber would likely result of an “over-driven” test and an incorrect finding that gin dust was explosible. The result of CAAQES testing was that gin dust was not explosible.     

Flame propagation through dust clouds of nano and micron scale aluminum particles

Temperature measurement on propagating flame and minimum explosible concentration are investigated. The dust explosion experiments of nano-particle dust clouds exhibit higher temperature gradient in preheat zone and lower MEC than those of micron particle dust clouds. A heterogeneous model is proposed to describe the oxidation process under two extreme conditions: whether the alumina film is involved in the reaction or not. The new methodology allows the estimation of oxidation kinetics of growing alumina. For micron particle, the model clarifies that the activation energy which has been wrongly considered to be for aluminum oxidation should be for lattice diffusion, and the initial reaction rate is proved to be dominated by the diffusion rate of oxygen through alumina shell as diffusion controlled reaction. For nano-particle, the model explained that why the reported activation energy shows significantly lower than that for micron particle, due to initially ignorable alumina film or considered as kinetically controlled reaction. However, as reaction occurs and alumina builds up on the surface, the interference of alumina somewhat increases the activation energy.     

Ignitability characteristics of aluminium and magnesium dusts that are generated during the shredding of post-consumer wastes

The authors investigated the ignitability of aluminium and magnesium dusts that are generated during the shredding of post-consumer waste. The relations between particle size and the minimum explosive concentration, the minimum ignition energy, the ignition temperature of the dust clouds, etc. the relation between of oxygen concentration and dust explosion, the effect of inert substances on dust explosion, etc. were studied experimentally.

The minimum explosive concentration increased exponentially with particle size. The minimum explosive concentrations of the sample dusts were about 170 g/m³ (aluminium: 0–8 μm) and 90 g/m³ (magnesium: 0–20 μm). The minimum ignition energy tended to increase with particle size. It was about 6 mJ for the aluminium samples and 4 mJ for the magnesium samples. The ignition temperature of dust clouds was about 750 °C for aluminium and about 520 °C for magnesium. The lowest concentrations of oxygen to produce a dust explosion were about 10% for aluminium and about 8% for magnesium. A large mixing ratio (more than about 50%) of calcium oxide or calcium carbonate was necessary to decrease the explosibility of magnesium dust. The experimental data obtained in the present investigation will be useful for evaluating the explosibility of aluminium and magnesium dusts generated in metal recycling operations and thus for enhancing the safety of recycling plants.     

Prediction of dust cloud minimum ignition energy for organic dusts from modified hartmann tube data

The modified Hartmann tube apparatus is recognized to give realistic or safe indications of dust explosion violence. Evidence is presented that results from this apparatus can also be used to indicate minimum ignition energy. Published data show a correlation between minimum ignition energy and minimum explosible concentration, which is refined by also taking into account explosive violence. An empirical model has been derived, relating minimum ignition energy to minimum explosible concentration and explosive violence. The model allows estimation of probabilities of minimum ignition energy falling below specified values, such as those recognized as of practical importance by the relevant British Standard. A limited test of the model suggests that it can be applied to modified Hartmann tube data. It is anticipated that the model will be valuable as a screening tool, especially in the early stages of development of a project.     

惰性粉体对蔗糖粉尘最小点火能的影响研究

为了预防蔗糖粉尘爆炸,利用1.2 L哈特曼管研究了NH₄H₂PO₄与Al(OH₄对蔗糖粉尘爆炸的抑制作用。在蔗糖粉尘质量分数一定的条件下,通过改变 NH₄H₂PO₄与Al(OH)₄的粒径和质量分数,测定其对蔗糖粉尘爆炸的抑制效果。结果表明:随着NH₄H₂PO₄和Al(OH)₄质量分数的增加,粒径的减小,蔗糖粉尘的最小点火能均逐渐增大,当惰性粉体增加到一定质量时,蔗糖粉尘被完全惰化,在蔗糖粉尘中分别加入粒径为48~74,38~47,25~37 μm的NH₄H₂PO₄和Al(OH)₄,3种粒径的NH₄H₂PO₄使蔗糖粉尘完全惰化的质量分数分别为40%,35%,30%,3种粒径的Al(OH)₃使蔗糖粉尘惰化的质量分数均为60%。因此(NH₄)H₂PO₄抑制蔗糖粉尘爆炸的效果比Al(OH)₃更显著。     

Experimental study on the minimum explosion concentration of anthracite dust: The roles of O2 mole fraction,inert gas and CH4 addition

The explosion characteristics of anthracite coal dust with/without small amount of CH₄ (1.14 vol %) were investigated by using a 20 L spherical explosion apparatus with an emphasis on the roles of oxygen mole fraction and inert gas. Two methods based on overpressure and combustion duration time were used to determine the minimum explosion concentration (MEC) or the lower explosion limit (LEL) of the pure anthracite coal dust and the hybrid coal-methane mixtures, respectively. The experiment results showed that increasing oxygen mole fraction increases the explosion risk of coal dust: with increasing oxygen mole fraction, the explosion pressure (P_ex) and the rate of explosion pressure rise ((dp/dt)_ex)) increase, while MEC decreases. The explosion risk of anthracite dust was found to be lower after replacing N₂ with CO₂, suggesting that CO₂ has a better inhibition effect on explosion mainly due to its higher specific heat. However, the addition of 1.14% CH₄ moderates the inhibition effect of CO₂ and the promotion effect of O₂ on anthracite dust explosion for some extent, increasing explosion severity and reducing the MEC of anthracite dust. For hybrid anthracite/CH₄ mixture explosions, Barknecht's curve was found to be more accurate and conservative than Chatelier's line, but neither are sufficient from the safety considerations. The experimental results provide a certain help for the explosion prevention and suppression in carbonaceous dust industries.     

固体惰性介质对煤粉爆炸压力的影响研究

通过对固体惰性介质在减轻煤粉爆炸作用的实验研究,给出影响固体惰化剂作用效果的主要影响因素。实验分别选用来自加拿大和中国的3种煤粉和石灰石,对每种实验样品的成分、粒度都进行分析。用20L球形容器进行实验,测定煤粉中加入不同含量的石灰石后煤粉爆炸的Pmax和(dp/dt)max值。结果表明,石灰石能够起到减轻煤粉爆炸影响的作用,并且随着煤粉粒度的减小,要达到相同的抑爆效果需要的石灰石的用量将加大。     

三环唑粉尘爆炸特性研究

利用激光粒度仪对三环唑粉尘的粒径分布进行分析,并用20 L爆炸球测试装置、哈特曼管装置探讨了粉尘质量浓度、点火延迟时间、点火能量、粒径分布对粉尘爆炸的影响并总结了相关规律。实验结果表明:粉尘粒度是影响粉尘最小点火能和爆炸下限的单调因素,粉尘质量浓度是影响粉尘爆炸压力的极值因素,点火延迟时间是影响粉尘最小点火能的极值因素。     

Collecting representative dust samples: A comparison of various sampling methods in underground coal mines

Former methods used in the U.S. to assess hazardous and explosible coal dust date back to the 1950s. As mining technologies advanced, so too have the hazards. Given the results of the recent coal dust particle size survey and full-scale experimental mine explosion tests, the National Institute for Occupational Safety and Health (NIOSH) recommended a new minimum standard, in the absence of background methane, of 80% total incombustible content (TIC) be required in the intake airways of bituminous coal mines, replacing the previous 65% TIC requirement. Most important to monitoring and maintaining the 80% TIC is the ability to effectively collect and analyze representative dust samples that would likely disperse and participate in dust explosion propagation. Research has shown that dust suspended on elevated surfaces is usually finer, more reactive, and more readily dispersible while floor deposits of dust are generally coarser and more difficult to disperse given the same blast of air. The roof, rib, and floor portions of the dust samples were collected and analyzed for incombustible content separately and the results were compared to a band sample of the roof, rib, and floor components. Results indicate that the roof and rib dust samples should be kept separate from floor dust samples and considered individually for analyses. The various experimental collection methods are detailed along with preferred sampling approaches that improve the detectability of potentially hazardous accumulations of explosible dust.     

戊唑醇粉尘最小点火能试验研究

采用1.2 L哈特曼管爆炸装置分别对粒径小于54μm、74μm、150μm及大于150μm的戊唑醇粉尘进行测试。针对戊唑醇粉尘浓度及粒径范围对其最小点火能的影响,分别进行单因素试验,并对其危险性进行分级。结果表明,保持粒径小于150μm,环境温度为20℃,喷粉压力为0.7 MPa,在质量浓度100~1 300 g/m~3之间,戊唑醇粉尘的最佳敏感质量浓度ρ_m为983.71 g/m~3,此时的最小点火能为404.74 mJ。保持戊唑醇粉尘质量浓度为900 g/m~3,环境温度为20℃,喷粉压力为0.7 MPa不变,粒径小于54μm、74μm、150μm及大于150μm的戊唑醇粉尘的最小点火能分别为10 mJ、100 mJ、400 mJ和1 000 mJ以上。因此,判定戊唑醇粉尘最小点火能属于M2级,为特别着火敏感性。     

爆炸事故及预防

为了促进我国的爆炸安全研究工作更深入发展,本文列出了利用爆炸激波管技术测定氢气、汽油、铝粉等可爆性物质的爆炸特性。研究表明:这些可爆性物质在一定条件都能形成破坏力极大的爆轰现象。实验确定了氢、汽油和氧混合物的可爆(轰)极限、可燃性极限、混合物临界初始压力等爆炸临界条件。控制可爆性物质的初始条件不超过其爆炸临界条件,能够防止爆轰或爆燃现象发生;添加不参加反应的物质(如氩气、氮气、水蒸汽等)能够使已达到爆炸条件的混合物阻爆。本文的数据可供有关部门参考。     

Explosion characteristics of micron- and nano-size magnesium powders

Explosion characteristics of micron- and nano-size magnesium powders were determined using CSIR-CBRI 20-L Sphere, Hartmann apparatus and Godbert-Greenwald furnace to study influence of particle size reduction to nano-range on these. The explosion parameters investigated are: maximum explosion pressure (P_max), maximum rate of pressure-rise (dP/dt)_max, dust explosibility index (K_St), minimum explosible concentration (MEC), minimum ignition energy (MIE), minimum ignition temperature (MIT), limiting oxygen concentration (LOC) and effect of reduced oxygen level on explosion severity. Magnesium particle sizes are: 125, 74, 38, 22, 10 and 1 μm; and 400, 200, 150, 100, 50 and 30 nm. Experimental results indicate significant increase in explosion severity (P_max: 7–14 bar, K_St: 98–510 bar·m/s) as particle size decreases from 125 to 1 μm, it is maximum for 400 nm (P_max: 14.6 bar, K_St: 528 bar·m/s) and decreases with further decrease of particle size to nano-range 200–30 nm (P_max: 12.4–9.4 bar, K_St: 460–262 bar·m/s) as it is affected by agglomeration of nano-particles. MEC decreases from 160 to 30 g/m³ on decreasing particle size from 125 to 1 μm, its value is 30 g/m³ for 400 and 200 nm and 20 g/m³ for further decrease in nano-range (150–30 nm). MIE reduces from 120 to 2 mJ on decreasing the particle size from 125 to 1 μm, its value is 1 mJ for 400, 200, 150 nm size and <1 mJ for 50 and 30 nm. Minimum ignition temperature is 600 °C for 125 μm magnesium, it varies between 570 and 450 °C for sizes 38–1 μm and 400–350 °C for size range 400–30 nm. Magnesium powders in nano-range (30–200 nm) explode less violently than micron-range powder. However, likelihood of explosion increases significantly for nano-range magnesium. LOC is 5% for magnesium size range 125–38 μm, 4% for 22–1 μm, 3% for 400 nm, 4% for 200, 150 and 100 nm, and 5% for 50 and 30 nm. Reduction in oxygen levels to 9% results in decrease in P_max and K_St by a factor of 2–3 and 4–5, respectively, for micron as well as nano-sizes. The experimental data presented will be useful for industries producing or handling similar size range micron- and nano-magnesium in order to evaluate explosibility of their magnesium powders and propose/design adequate safety measures.     

苯乙烯丙烯酸共聚物/碳黑混合体系粉尘爆炸特性研究

采用MIE-D1.2型最小点火能测试装置及20 L球型粉尘爆炸测试装置,对苯乙烯丙烯酸共聚物/碳黑混合体系粉尘的爆炸特性进行研究。结果表明,过74μm、58μm、47μm孔径筛的粉尘对静电火花敏感,其最小点火能表征值分别为610 mJ、361 mJ、201 mJ。随粉尘质量浓度增加,最小点火能呈现先减小后增加的规律。随粉尘粒径减小,最小点火能与粉尘质量浓度变化关系曲线向低粉尘质量浓度和低点火能量方向偏移,且对应的最敏感爆炸质量浓度从500 g/m~3降至200 g/m~3。随粉尘质量浓度增加,过147μm、74μm、47μm孔径筛的苯乙烯丙烯酸共聚物/碳黑混合体系粉尘爆炸压力及爆炸压力上升速率呈现先增加后减小趋势。在相同粉尘质量浓度下,中位径小于74μm的苯乙烯丙烯酸共聚物/碳黑混合体系粉尘,粉尘的爆炸压力增幅明显减小。苯乙烯丙烯酸共聚物/碳黑混合体系粉尘爆炸下限质量浓度为25 g/m~3,最大爆炸指数为14.636 MPa·m/s,爆炸危险等级划分为St1。     

Minimum ignition temperatures and explosion characteristics of micron-sized aluminium powder

To forestall, control, and mitigate the detrimental effects of aluminium dust, a 20-L near-spherical dust explosion experimental system and an HY16429 type dust-cloud ignition temperature test device were employed to explore the explosion characteristics of micron-sized aluminium powder under different ignition energies, dust particle sizes, and dust cloud concentration (C_dust) values; the minimum ignition temperature (MIT) values of aluminium powder under different dust particle sizes and C_dust were also examined. Flame images at different times were photographed by a high-speed camera. Results revealed that under similar dust-cloud concentrations and with dust particle size increasing from 42.89 to 141.70 μm, the MIT of aluminium powder increased. Under various C_dust values, the MIT of aluminium dust clouds attained peak value when concentrations enhanced. Furthermore, the increase of ignition energy contributed to the increase of the explosion pressure (P_ex) and the rate of explosion pressure rise [(dP/dt)_ex]. When dust particle size was augmented gradually, the P_ex and (dP/dt)_ex attenuated. Decreasing particle size lowered both the most violent explosion concentration and explosive limits.     

Agricultural waste pulverised biomass: MEC and flame speeds

A modified Hartmann dust explosion tube was employed to determine the Minimum Explosible Concentration (MEC) and the flame speed for three Pakistani agricultural wastes: bagasse, rice husk and wheat straw. Agricultural biomass had a higher ash content than for woody biomass and this influenced the MEC. The dispersion, ignition and MEC were influenced by the particle size distribution, as also demonstrated by high speed video. There was a strong linear correlation between the MEC and the sum of the ash and moisture content of these and other biomasses, indicating that this inert mass in the particles acted to reduce the flame temperature and reduce the lean flammability limit or MEC. Comparison of the results was made with non-agricultural waste pulverized biomass. Peak flame speeds were approximately 2.5 m/s. The lean limits for these pulverised agricultural waste biomasses were comparable to that of pulverised wood but were much leaner than those for coal and hydrocarbon fuels, which indicate that these biomasses are highly reactive.