Effect of nitrobenzene on the performance and bacterial community in an expanded granular sludge bed reactor treating high-sulfate organic wastewater

Less than 50 mg/L nitrobenzene brought little effect on anaerobic sulfate reduction. Kinetics of sulfate reduction under different nitrobenzene contents was studied. Increased nitrobenzene contents greatly changed the bacterial community structure. Genus Desulfovibrio played the key role in anaerobic sulfate reduction process. Nitrobenzene (NB) is frequently found in wastewaters containing sulfate and may affect biological sulfate reduction process, but information is limited on the responses of sulfate reduction efficiency and microbial community to the increased NB contents. In this study, a laboratory-scale expanded granular sludge bed reactor was operated continuously to treat high-sulfate organic wastewater with increased NB contents. Results successfully demonstrated that the presence of more than 50 mg/L NB depressed sulfate reduction and such inhibition was partly reversible. Bath experiments showed that the maximum specific desulfuration activity (SDA) decreased from 135.80 mg SO₄^2?/gVSS/d to 30.78 mg SO₄^2?/gVSS/d when the NB contents increased from none to 400 mg/L. High-throughput sequencing showed that NB also greatly affected bacterial community structure. Bacteroidetes dominated in the bioreactor. The abundance of Proteobacteria increased with NB addition while Firmicutes presented an opposite trend. Proteobacteria gradually replaced Firmicutes for the dominance in response to the increase of influent NB concentrations. The genus Desulfovibrio was the dominant sulfate-reducing bacteria (SRB) with absence or presence of NB, but was inhibited under high content of NB. The results provided better understanding for the biological sulfate reduction under NB stress.     

Deciphering the effect of sodium dodecylbenzene sulfonate on up-flow anaerobic sludge blanket treatment of synthetic sulfate-containing wastewater

• UASB reactor can work efficiently with high COD/SO₄^2- ratios when SDBS exists. • Outcome of the competition between SRB and MPA was affected by SDBS. • Presence of SDBS makes methanogens with H₂/CO₂ as a substrate dominant. • Microbial diversity decreases in the presence of SDBS. In this study, the effects of organic sulfur on anaerobic biological processes were investigated by operating two up-flow anaerobic sludge blanket (UASB) reactors with sodium dodecylbenzene sulfonate (SDBS) as a representative of organic sulfur. The results indicated that the specific methanogenic activity (SMA) and chemical oxygen demand (COD) removal efficiency of R2 (with SDBS added) were higher than those of R1 (without SDBS) when the COD/SO₄²⁻ ratio was above 5.0. However, when the COD/SO₄²⁻ ratio was lower than 5.0, the sulfate reduction efficiency of R2 was higher than that of R1. These results and the observed SDBS transformation efficiency in anaerobic reactors indicate that low concentrations of SDBS accelerate methane production and the continuous accumulation of SDBS does not weaken the reduction of sulfate. Similarly, the calculated electron flux for a COD/SO₄²⁻ ratio of 1.0 indicates that the utilization intensity of electrons by sulfate-reducing bacteria (SRB) in R2 was 36.48% higher than that of SRB in R1 and exceeded that of methane-producing archaea (MPA) under identical working conditions. Moreover, the addition of SDBS in R2 made sulfidogenesis the dominant reaction at low COD/SO₄²⁻, and Methanobacterium and Methanobrevibacter with H₂/CO₂ as the substrate and Desulfomicrobium were the dominant MPA and SRB, respectively. However, methanogenesis was still the dominant reaction in R1, and Methanosaeta with acetic acid as the substrate and Desulfovibrio were the dominant MPA and SRB, respectively.     

Comparison of membrane fouling in ultrafiltration of down-flow and up-flow biological activated carbon effluents

The UF membrane fouling by down- and up-flow BAC effluents were compared. Up-flow BAC effluent fouled the membrane faster than down-flow BAC effluent. The combined effects dominated irreversible fouling. The extent of fouling exacerbated by inorganic particles was higher. The TMP, permeate flux, and normalized membrane flux during 21 days of UF of DBAC and UBAC effluents. Fouling during ultrafiltration of down- and up-flow biological activated carbon effluents was investigated to determine the roles of polysaccharides, proteins, and inorganic particles in ultrafiltration membrane fouling. During ultrafiltration of down- flow biological activated carbon effluent, the trans-membrane pressure was≤26 kPa and the permeate flux was steady at 46.7 L?m⁻²?h⁻¹. However, during ultrafiltration of up-flow biological activated carbon effluent, the highest trans-membrane pressure was almost 40 kPa and the permeate flux continuously decreased to 30 L?m⁻²?h⁻¹. At the end of the filtration period, the normalized membrane fluxes were 0.88 and 0.62 for down- and up-flow biological activated carbon effluents, respectively. The membrane removed the turbidity and polysaccharides content by 47.4% and 30.2% in down- flow biological activated effluent and 82.5% and 22.4% in up-flow biological activated carbon effluent, respectively, but retained few proteins. The retention of polysaccharides was higher on the membrane that filtered the down- flow biological activated effluent compared with that on the membrane that filtered the up-flow biological activated carbon effluent. The polysaccharides on the membranes fouled by up-flow biological activated carbon and down- flow biological activated effluents were spread continuously and clustered, respectively. These demonstrated that the up-flow biological activated carbon effluent fouled the membrane faster. Membrane fouling was associated with a portion of the polysaccharides (not the proteins) and inorganic particles in the feed water. When there was little difference in the polysaccharide concentrations between the feed waters, the fouling extent was exacerbated more by inorganic particles than by polysaccharides.     

Energy reduction of a submerged membrane bioreactor using a polytetrafluoroethylene (PTFE) hollow-fiber membrane

The fiber length and packing density of the PTFE membrane element were increased. The MBR was stably operated under an SAD^m of 0.13 m³·m^-2·hr^-1. Specific energy consumption was estimated to be less than 0.4 kWh·m^-3. In this study, we modified a polytetrafluoroethylene (PTFE) hollow-fiber membrane element used for submerged membrane bioreactors (MBRs) to reduce the energy consumption during MBR processes. The high mechanical strength of the PTFE membrane made it possible to increase the effective length of the membrane fiber from 2 to 3 m. In addition, the packing density was increased by 20% by optimizing the membrane element configuration. These modifications improve the efficiency of membrane cleaning associated with aeration. The target of specific energy consumption was less than 0.4 kWh·m^-3 in this study. The continuous operation of a pilot MBR treating real municipal wastewater revealed that the MBR utilizing the modified membrane element can be stably operated under a specific air demand per membrane surface area (SAD_m) of 0.13 m³·m^-2·hr^-1 when the daily-averaged membrane fluxes for the constant flow rate and flow rate fluctuating modes of operation were set to 0.6 and 0.5 m³·m^-2·d^-1, respectively. The specific energy consumption under these operating conditions was estimated to be less than 0.37 kWh·m^-3. These results strongly suggest that operating an MBR equipped with the modified membrane element with a specific energy consumption of less than 0.4 kWh·m^-3 is highly possible.     

Effects of Al3+ on pollutant removal and extracellular polymeric substances (EPS) under anaerobic,anoxic and oxic conditions

The highest removal efficiencies of COD and TN were achieved under 10 mg/L of Al³⁺. The highest TP removal efficiency occurred under 30 mg/L of Al³⁺. EPS, PS and PN concentrations increased with the addition of Al³⁺. Sludge properties significantly changed with the addition of Al³⁺. Aluminum ions produced by aluminum mining, electrolytic industry and aluminum-based coagulants can enter wastewater treatment plants and interact with activated sludge. They can subsequently contribute to the removal of suspended solids and affect activated sludge flocculation, as well as nitrogen and phosphorus removal. In this study, the effects of Al³⁺ on pollutant removal, sludge flocculation and the composition and structure of extracellular polymeric substances (EPS) were investigated under anaerobic, anoxic and oxic conditions. Results demonstrated that the highest chemical oxygen demand (COD) and total nitrogen (TN) removal efficiencies were detected for an Al³⁺ concentration of 10 mg/L. In addition, the maximal dehydrogenase activity and sludge flocculation were also observed at this level of Al³⁺. The highest removal efficiency of total phosphorus (TP) was achieved at an Al³⁺ concentration of 30 mg/L. The flocculability of sludge in the anoxic zone was consistently higher than that in the anaerobic and oxic zones. The addition of Al³⁺ promoted the secretion of EPS. Tryptophan-like fluorescence peaks were detected in each EPS layer in the absence of Al³⁺. At the Al³⁺ concentration of 10 mg/L, fulvic acid and tryptophan fluorescence peaks began to appear, while the majority of protein species and the highest microbial activity were also detected. Low Al³⁺ concentrations (<10 mg/L) could promote the removal efficiencies of COD and TN, yet excessive Al³⁺ levels (>10 mg/L) weakened microbial activity. Higher Al³⁺ concentrations (>30 mg/L) also inhibited the release of phosphorus in the anaerobic zone by reacting with PO₄^3-.     

Microbial community dynamics at high organic loading rates revealed by pyrosequencing during sugar refinery wastewater treatment in a UASB reactor

High strength sugar refinery wastewater was treated in a mesophilic UASB. Pyrosequencing reveals microbial community succession with OLR increase. Diversity of microbial communities in OLR12 is much higher than those in OLR36 and OLR54.0 kgCOD/(kg VSS·d). Fermentative bacteria could deal with increasing OLR through the increase of microbial diversity and quantity. Hydrogen-producing acotogens and methanogens mainly coped with high OLR shocks by increasing the quantity of community The performance and microbial community structure in an upflow anaerobic sludge blanket reactor (UASB) treating sugar refinery wastewater were investigated. The chemical oxygen demand (COD) removal reached above 92.0% at organic loading rates (OLRs) of 12.0–54.0 kgCOD/(m³·d). The volatile fatty acids (VFAs) in effluent were increased to 451.1 mg/L from 147.9 mg/L and the specific methane production rate improved by 1.2–2.2-fold as the OLR increased. The evolution of microbial communities in anaerobic sludge at three different OLRs was investigated using pyrosequencing. Operational taxonomic units (OTUs) at a 3% distance were 353, 337 and 233 for OLR12, OLR36 and OLR54, respectively. When the OLR was increased to 54.0 kgCOD /(m³·d) from 12.0 kgCOD/(m³·d) by stepwise, the microbial community structure were changed significantly. Five genera (Bacteroides, Trichococcus, Chryseobacterium, Longilinea and Aerococcus) were the dominant fermentative bacteria at the OLR 12.0 kgCOD/(m³·d). However, the sample of OLR36 was dominated by Lactococcus, Trichococcus, Anaeroarcus and Veillonella. At the last stage (OLR= 54.0 kgCOD/(m³·d)), the diversity and percentage of fermentative bacteria were markedly increased. Apart from fermentative bacteria, an obvious shift was observed in hydrogen-producing acetogens and non-acetotrophic methanogens as OLR increased. Syntrophobacter, Geobacter and Methanomethylovorans were the dominant hydrogen-producing acetogens and methylotrophic methanogens in the samples of OLR12 and OLR36. When the OLR was increased to 54.0 kgCOD/(m³·d), the main hydrogen-producing acetogens and hydrogenotrophic methanogens were substituted with Desulfovibrio and Methanospirillum. However, the composition of acetotrophic methanogens (Methanosaeta) was relatively stable during the whole operation period of the UASB reactor.     

Aggravation of membrane fouling and methane leakage by a three-phase separator in an external anaerobic ceramic membrane bioreactor

The existence of three-phase separator did not affect COD removal in the EAnCMBR. The existence of three-phase separator aggravated methane leakage of EAnCMBR. The existence of three-phase separator aggravated membrane fouling rate of EAnCMBR. Start-up of EAnCMBR equipped three-phase separator was slightly delayed. The three-phase separator is a critical component of high-rate anaerobic bioreactors due to its significant contribution in separation of biomass, wastewater, and biogas. However, its role in an anaerobic membrane bioreactor is still not clear. In this study, the distinction between an external anaerobic ceramic membrane bioreactor (EAnCMBR) unequipped (R1) and equipped (R2) with a three-phase separator was investigated in terms of treatment performance, membrane fouling, extracellular polymers of sludge, and microbial community structure. The results indicate that the COD removal efficiencies of R1 and R2 were 98.2%±0.4% and 98.1%±0.4%, respectively, but the start-up period of R2 was slightly delayed. Moreover, the membrane fouling rate of R2 (0.4 kPa/d) was higher than that of R1 (0.2 kPa/d). Interestingly, the methane leakage from R2 (0.1 L/d) was 20 times higher than that from R1 (0.005 L/d). The results demonstrate that the three-phase separator aggravated the membrane fouling rate and methane leakage in the EAnCMBR. Therefore, this study provides a novel perspective on the effects of a three-phase separator in an EAnCMBR.     

Effect of 2-butenal manufacture wastewater to methanogenic activity and microbial community

The inhibition ratio sharply increased with the increasing COD. The absorbance of UV-vis at 420 nm showed a linear correlation with the SMA. The molecular structure of EPS has changed when COD was 9585 mg/L. Illumina Miseq sequencing was employed to reveal the microbial composition. The synthesis of 2-butenal, which is a vital raw material for the production of sorbic acid as a food preservative, generates some toxic by-products, so it is urgent to seek better detoxification strategies for the treatment of 2-butenal manufacture wastewater. In this study, batch experiments were carried out to investigate the inhibition effect of wastewater on the methanogenic activity. To understand the wastewater toxicity to anaerobic granular sludge, variations of the specific methanogenic activity (SMA) and extracellular polymeric substance (EPS) constituents at various wastewater CODs were investigated. Ultraviolet-visible (UV-vis) spectra and Fourier transform infrared (FT-IR) spectra were employed to analyze the structure of the EPS. The results showed that the inhibitory ratio of 2-butenal manufacture wastewater was less than 8.4% on the anaerobic granular sludge when the CODs were less than 959 mg/L. However, the inhibitory ratio increased from 36.4% to 93.6% when CODs increased from 2396 mg/L to 9585 mg/L, with the SMA decreasing from 39.1 mL CH₄/(gVSS·d) to 3.2 mL CH₄/(gVSS·d). The diversity of the microbial community under various CODs was researched by Illumina 16S rRNA Miseq sequencing and the results demonstrated that Proteiniphilum、Petrimonas and Syntrophobacter were the dominant bacteria genera in all sample. Regarding archaea, Methanobacterium was the most dominated archaea genera, followed by the Methanosaeta group in all samples. Moreover, the bacterial communities had changed obviously with increasing CODs, which indicated high CODs played a negative impact on the richness and diversity of bacterial community in the sludge samples.     

Enhanced methane production during long-term UASB operation at high organic loads as enabled by the immobilized Fungi

• Fungi enable the constant UASB operation even at OLR of 25.0 kg/(m³×d). • The COD removal of 85.9% and methane production of 5.6 m³/(m³×d) are achieved. • Fungi inhibit VFAs accumulation and favor EPS generation and sludge granulation. • Fungi enrich methanogenic archaea and promote methanogenic pathways. Anaerobic digestion is widely applied in organic wastewater treatment coupled with bioenergy production, and how to stabilize its work at the high organic loading rate (OLR) remains a challenge. Herein, we proposed a new strategy to address this issue via involving the synergetic role of the Aspergillus sydowii 8L-9-F02 immobilized beads (AEBs). A long-term (210-day) continuous-mode operation indicated that the upflow anaerobic sludge bed (UASB) reactor (R1, with AEBs added) could achieve the OLR as high as 25.0 kg/(m³×d), whereas the control reactor (R0, with AEBs free) could only tolerate the maximum OLR of 13.3 kg/(m³×d). Remarkably, much higher COD removal (85.9% vs 23.9%) and methane production (5.4 m³/(m³×d) vs 2.2 m³/(m³×d)) were achieved in R1 than R0 at the OLR of 25.0 kg/(m³×d). Such favorable effect results from the facts that fungi inhibit VFAs accumulation, favor the pH stabilization, promote the generation of more extracellular polymeric substance, and enhance the sludge granulation and settleability. Moreover, fungi may enhance the secretion of acetyl-coenzyme A, a key compound in converting organic matters to CO₂. In addition, fungi are favorable to enrich methanogenic archaea even at high OLR, improving the activity of acetate kinase and coenzyme F₄₂₀ for more efficient methanogenic pathway. This work may shed new light on how to achieve higher OLR and methane production in anaerobic digestion of wastewater.     

Statistical modeling of radiolytic (60Co g) degradation of Ofloxacin,antibiotic: Synergetic effect,kinetic studies & assessment of its degraded metabolites

Linear, interactive and quadratic effects of process parameters were studied. Degradation of Ofloxacin (Ofx) was related with G value of irradiation process. The synergistic effect of H₂O₂ on lower dose of g-irradiation was established. The process follows pseudo first order with dose constant (d = 0.232 kGy^–1). The impact of human activities in the past few decades has paved the way for the release of pollutants due to the improper effluent treatment. Recent studies revealed that, Ofloxacin, an antibiotic as one of the major pollutant affecting surface water and ground water. In this study, the radiolytic potential of Ofloxacin was investigated. The effects of pH, dose and concentration of Ofloxacin were analyzed using One Factor At a Time (OFAT) and the interactive effects between the parameters were studied using Face Centered Central Composite Design. The statistically optimised developed model shows 30% degradation at initial antibiotic concentration of 1mM at pH 3.0 and at 2 kGy dose of gamma ray. The process efficiency was evaluated in terms of G value and its correlation with the concentration of antibiotic was also established. The process of degradation was augmented by the addition of H₂O₂ (1.5 mM). The reaction kinetics for the process was evaluated, the dose rate constant and the rate of degradation for the augmented process was found to be 0.232 kGy^-1 and 0.232 mM/kGy, respectively. The degraded metabolites of the radiolytic degradation of Ofloxacin were analyzed through change in pH, reduction in TOC and GC-MS spectrum.     

Occurrence of veterinary antibiotics in struvite recovery from swine wastewater by using a fluidized bed

Antibiotics in wastewater pose pharmacological threats to phosphorous recovery. Recovered struvite particles possessed significantly antibiotic residues. Smaller granules contained much more antibiotics than the larger ones. Organic matters and struvite granulation process exerted significant impacts. Recovering phosphorus from livestock wastewater has gained extensive attention. The residue of veterinary antibiotics in the wastewater may be present in the recovered products, thereby posing pharmacological threats to the agricultural planting and human health. This study investigated antibiotic occurrence in the struvite particles recovered from swine wastewater by using a fluidized bed. Results revealed that tetracyclines possessed significant residues in the struvite granules, with the values ranging from 195.2 mg·kg⁻¹ to 1995.0 mg·kg⁻¹. As for fluoroquinolones, their concentrations varied from 0.4 mg·kg⁻¹ to 1104.0 mg·kg⁻¹. Struvite particles were of various sizes and shapes and displayed different antibiotic adsorption capacities. The data also showed that the smaller granules contained much more antibiotics than the larger ones, indicating that the fluidized granulation process of struvite crystals plays an important role on the accumulation of antibiotics. For tetracyclines, organic matters and struvite adsorption exerted significant impacts on tetracyclines migration. The outcomes underscore the need to consider the residues of antibiotics in resource recovery from wastewater because they exert pharmacological impacts on the utilization of recovered products.     

Ozonation of the 5-fluorouracil anticancer drug and its prodrug capecitabine: Reaction kinetics,oxidation mechanisms,and residual toxicity

Specific second-order rate constants were determined for 5-FU and CAP with ozone. Reaction sites were confirmed by kinetics, Fukui analysis, and products. The olefin moiety was the main ozone reaction site for 5-FU and CAP. Carboxylic acids comprised most of the residual TOC for 5-FU. Ozonation removed the toxicity associated with 5-FU and products but not CAP. Anticancer drugs (ADs) have been detected in the environment and represent a risk to aquatic organisms, necessitating AD removal in drinking water and wastewater treatment. In this study, ozonation of the most commonly used antimetabolite ADs, namely 5-fluorouracil (5-FU) and its prodrug capecitabine (CAP), was investigated to determine reaction kinetics, oxidation mechanisms, and residual toxicity. The specific second-order rate constants between aqueous ozone and 5-FU, 5-FU⁻, 5-FU²⁻, CAP, and CAP⁻ were determined to be 7.07(±0.11)×10⁴ M⁻¹·s⁻¹, 1.36(±0.06)×10⁶ M⁻¹·s⁻¹, 2.62(±0.17)×10⁷ M⁻¹·s⁻¹, 9.69(±0.08)×10³ M⁻¹·s⁻¹, and 4.28(±0.07)×10⁵ M⁻¹·s⁻¹, respectively; furthermore, the second-order rate constants for ^•OH reaction with 5-FU and CAP at pH 7 were determined to be 1.85(±0.20)×10⁹ M⁻¹·s⁻¹ and 9.95(±0.26)×10⁹ M⁻¹·s⁻¹, respectively. Density functional theory was used to predict the main ozone reaction sites of 5-FU (olefin) and CAP (olefin and deprotonated secondary amine), and these mechanisms were supported by the identified transformation products. Carboxylic acids constituted a majority of the residual organic matter for 5-FU ozonation; however, carboxylic acids and aldehydes were important components of the residual organic matter generated by CAP. Ozone removed the toxicity of 5-FU to Vibrio fischeri, but the residual toxicity of ozonated CAP solutions exhibited an initial increase before subsequent removal. Ultimately, these results suggest that ozone is a suitable technology for treatment of 5-FU and CAP, although the residual toxicity of transformation products must be carefully considered.     

Characteristic and correlation analysis of influent and energy consumption of wastewater treatment plants in Taihu Basin

Poor biodegradability and insufficient carbon source are discovered from influent. Influent indices presented positively normal distribution or skewed distribution. Average energy consumption of WWTPs in Taihu Basin was as high as 0.458 kWh/m³. Energy consumption increases with the increase in influent volume and COD reduction. The total energy consumption decreases with the NH₃-N reduction. The water quality and energy consumption of wastewater treatment plants (WWTPs) in Taihu Basin were evaluated on the basis of the operation data from 204 municipal WWTPs in the basin by using various statistical methods. The influent ammonia nitrogen (NH₃-N) and total nitrogen (TN) of WWTPs in Taihu Basin showed normal distribution, whereas chemical oxygen demand (COD), biochemical oxygen demand (BOD₅), suspended solid (SS), and total phosphorus (TP) showed positively skewed distribution. The influent BOD₅/COD was 0.4%–0.6%, only 39.2% SS/BOD₅ exceeded the standard by 36.3%, the average BOD₅/TN was 3.82, and the probability of influent BOD₅/TP>20 was 82.8%. The average energy consumption of WWTPs in Taihu Basin in 2017 was 0.458 kWh/m³. The specific energy consumption of WWTPs with a daily treatment capacity of more than 5 × 10⁴ m³ in Taihu Basin was stable at 0.33 kWh/m³. A power function relationship was observed between the reduction in COD and NH₃-N and the specific energy consumption of pollutant reduction, and the higher the pollutant reduction is, the lower the specific energy consumption of pollutant reduction presents. In addition, a linear relationship existed between the energy consumption of WWTPs and the specific energy consumption of influent volume and pollutant reduction. Therefore, upgrading and operation with less energy consumption of WWTPs is imperative and the suggestions for Taihu WWTPs based on stringent discharge standard are proposed in detail.     

Effective removal of Cd2+ and Pb2+ pollutants from wastewater by dielectrophoresis-assisted adsorption

Dielectrophoresis (DEP) process could enhance the removal the Cd²⁺ and Pb²⁺ with less absorbent. The removal rates of both Cd²⁺ and Pb²⁺ increased with the increase of voltage. The overall removal rate of Cd²⁺ and Pb²⁺ in the binary system is higher than that of Cd²⁺ or Pb²⁺ in the single system. DEP could cause considerable changes of the bentonite particles in both surface morphology and microstructure. Dielectrophoresis (DEP) was combined with adsorption (ADS) to simultaneously and effectively remove Cd²⁺ and Pb²⁺ species from aqueous solution. To implement the process, bentonite particles of submicro-meter size were used to first adsorb the heavy metal ions. These particles were subsequently trapped and removed by DEP. The effects of the adsorbent dosage, DEP cell voltage and the capture pool numbers on the removal rate were investigated in batch processes, which allowed us to determine the optimal experimental conditions. The high removal efficiency, 97.3% and 99.9% for Cd²⁺ and Pb²⁺, respectively, were achieved when the ions are coexisting in the system. The microstructure of bentonite particles before and after ADS/DEP was examined by scanning electron microscopy. Our results suggest that the dielectrophoresis-assisted adsorption method has a high capability to remove the heavy metals from wastewater.     

Nitrate removal to its fate in wetland mesocosm filled with sponge iron: Impact of influent COD/N ratio

• CW-Fe allowed a high-performance of NO₃^‒-N removal at the COD/N ratio of 0. • Higher COD/N resulted in lower chem-denitrification and higher bio-denitrification. • The application of s-Fe⁰ contributed to TIN removal in wetland mesocosm. • s-Fe⁰ changed the main denitrifiers in wetland mesocosm. Sponge iron (s-Fe⁰) is a porous metal with the potential to be an electron donor for denitrification. This study aims to evaluate the feasibility of using s-Fe⁰ as the substrate of wetland mesocosms. Here, wetland mesocosms with the addition of s-Fe⁰ particles (CW-Fe) and a blank control group (CW-CK) were established. The NO₃^‒-N reduction property and water quality parameters (pH, DO, and ORP) were examined at three COD/N ratios (0, 5, and 10). Results showed that the NO₃^‒-N removal efficiencies were significantly increased by 6.6 to 58.9% in the presence of s-Fe⁰. NH₄⁺-N was mainly produced by chemical denitrification, and approximately 50% of the NO₃^‒-N was reduced to NH₄⁺-N, at the COD/ratio of 0. An increase of the influent COD/N ratio resulted in lower chemical denitrification and higher bio-denitrification. Although chemical denitrification mediated by s-Fe⁰ led to an accumulation of NH₄⁺-N at COD/N ratios of 0 and 5, the TIN removal efficiencies increased by 4.5%‒12.4%. Moreover, the effluent pH, DO, and ORP values showed a significant negative correlation with total Fe and Fe (II) (P<0.01). High-throughput sequencing analysis indicated that Trichococcus (77.2%) was the most abundant microorganism in the CW-Fe mesocosm, while Thauera, Zoogloea, and Herbaspirillum were the primary denitrifying bacteria. The denitrifiers, Simplicispira, Dechloromonas, and Denitratisoma, were the dominant bacteria for CW-CK. This study provides a valuable method and an improved understanding of NO₃^‒-N reduction characteristics of s-Fe⁰ in a wetland mesocosm.     

Distribution and removal of antibiotic resistance genes during anaerobic sludge digestion with alkaline,thermal hydrolysis and ultrasonic pretreatments

Sludge digestion is critical to control the spread of ARGs from wastewater to soil. Fate of ARGs in three pretreatment-AD processes was investigated. UP was more efficient for ARGs removal than AP and THP in pretreatment-AD process. The total ARGs concentration showed significant correlation with 16S rRNA gene. The bacteria carrying ARGs could be mainly affiliated with Proteobacteria. Sewage sludge in the wastewater treatment plants contains considerable amount of antibiotic resistance genes (ARGs). A few studies have reported that anaerobic digestion (AD) could successfully remove some ARGs from sewage sludge, but information on the fate of ARGs in sludge pretreatment-AD process is still very limited. In this study, three sludge pretreatment methods, including alkaline, thermal hydrolysis and ultrasonic pretreatments, were compared to investigate the distribution and removal of ARGs in the sludge pretreatment-AD process. Results showed that the ARGs removal efficiency of AD itself was approximately 50.77%, and if these three sludge pretreatments were applied, the total ARGs removal efficiency of the whole pretreatment-AD process could be improved up to 52.50%–75.07%. The ultrasonic pretreatment was more efficient than alkaline and thermal hydrolysis pretreatments. Although thermal hydrolysis reduced ARGs obviously, the total ARGs rebounded considerably after inoculation and were only removed slightly in the subsequent AD process. Furthermore, it was found that the total ARGs concentration significantly correlated with the amount of 16S rRNA gene during the pretreatment and AD processes, and the bacteria carrying ARGs could be mainly affiliated with Proteobacteria.     

Fe2O3-CeO2-Bi2O3/γ-Al2O3 catalyst in the catalytic wet air oxidation (CWAO) of cationic red GTL under mild reaction conditions

Fe₂O₃-CeO₂-Bi₂O₃/γ-Al₂O₃, an environmental friendly material, was investigated. The catalyst exhibited good catalytic performance in the CWAO of cationic red GTL. The apparent activation energy for the reaction was 79 kJ·mol⁻¹. HO₂· and O₂·⁻ appeared as the main reactive species in the reaction. The Fe₂O₃-CeO₂-Bi₂O₃/γ-Al₂O₃ catalyst, a novel environmental-friendly material, was used to investigate the catalytic wet air oxidation (CWAO) of cationic red GTL under mild operating conditions in a batch reactor. The catalyst was prepared by wet impregnation, and characterized by special surface area (BET measurement), X-ray diffraction (XRD) and X-ray photoelectron spectroscopy (XPS). The Fe₂O₃-CeO₂-Bi₂O₃/γ-Al₂O₃ catalyst exhibited good catalytic activity and stability in the CWAO under atmosphere pressure. The effect of the reaction conditions (catalyst loading, degradation temperature, solution concentration and initial solution pH value) was studied. The result showed that the decolorization efficiency of cationic red GTL was improved with increasing the initial solution pH value and the degradation temperature. The apparent activation energy for the reaction was 79 kJ·mol⁻¹. Hydroperoxy radicals (HO₂·) and superoxide radicals (O₂⁻·) appeared as the main reactive species upon the CWAO of cationic red GTL.     

Comparison of CNT-PVA membrane and commercial polymeric membranes in treatment of emulsified oily wastewater

CNT-PVA membrane was fabricated and compared with polymeric membranes. The separation performance was evaluated by homemade and cutting fluid emulsions. The three membranes show similar oil retention rates. CNT-PVA membranes have higher permeation fluxes compared with polymeric membranes. CNT-PVA membrane shows higher fouling resistance. Membrane separation is an attractive technique for removal of emulsified oily wastewater. However, polymeric membranes which dominate the current market usually suffer from severe membrane fouling. Therefore, membranes with high fouling resistance are imperative to treat emulsified oily wastewater. In this study, carbon nanotube-polyvinyl alcohol (CNT-PVA) membrane was fabricated. And its separation performance for emulsified oily wastewater was compared with two commercial polymeric membranes (PVDF membrane and PES membrane) by filtration of two homemade emulsions and one cutting fluid emulsion. The results show that these membranes have similar oil retention efficiencies for the three emulsions. Whereas, the permeation flux of CNT-PVA membrane is 1.60 to 3.09 times of PVDF membrane and 1.41 to 11.4 times of PES membrane, respectively. Moreover, after five consecutive operation circles of filtration process and back flush, CNT-PVA membrane can recover 62.3% to 72.9% of its initial pure water flux. However, the pure water flux recovery rates are only 24.1% to 35.3% for PVDF membrane and 6.0% to 26.3% for PES membrane, respectively. Therefore, CNT-PVA membrane are more resistant to oil fouling compared with the two polymeric membranes, showing superior potential in treatment of emulsified oily wastewater.     

Characterization of CANON reactor performance and microbial community shifts with elevated COD/N ratios under a continuous aeration mode

COD/N at low ratios (0–0.82) improved N removals of CANON. CANON performance decreased after COD/N up to 0.82. The relative abundance of AOB decreased continuously with increasing COD/N. AOB outcompeted at a high COD load led to CANON failure. The relative abundance of AnAOB decreased and increased with increasing COD/N. The effects of increasing COD/N on nitrogen removal performance and microbial structure were investigated in a SBR adopting a completely autotrophic nitrogen removal over nitrite process with a continuous aeration mode (DO at approximately 0.15–0.2 mg/L). As the COD/N increased from 0.1 to≤0.59, the nitrogen removal efficiency (NRE) increased from 88.7% to 95.5%; while at COD/N ratios of 0.59–0.82, the NRE remained at 90.7%–95.5%. As the COD/N increased from 0.82 to 1.07, the NRE decreased continuously until reaching 60.1%. Nitrosomonas sp. (AOB) and Candidatus Jettenia (anammox bacteria) were the main functional genera in the SBR. As the COD/N increased from 0.10 to 1.07, the relative abundance of Nitrosomonas decreased from 13.4% to 2.0%, while that of Candidatus Jettenia decreased from 35% to 9.9% with COD/N<0.82 then increased to 45.4% at a COD/N of 1.07. Aerobic heterotrophic bacteria outcompeted AOB at high COD loadings (650 mg/L) because of oxygen competition, which ultimately led to deteriorated nitrogen removal performance.     

Enhanced nitrification in integrated floating fixed-film activated sludge (IFFAS) system using novel clinoptilolite composite carrier

Novel carriers with favorable electrophilicity and hydrophilicity were prepared. Novel carriers had the capability of nitrification-enhancing. NH₄⁺-N removal efficiency of IFFAS process rose up to 20% with novel carriers. Nitrosomonadales and Nitrospirales were identified as the functional nitrifiers. The population of Nitrospirales increased by 4.51%. The integrated floating fixed-film activated sludge (IFFAS) process is an ideal preference for nitrification attributing to the longer sludge age for nitrifiers. However, as the core of this process, conventional carriers made of polymer materials usually exhibit negative charge and hydrophobicity on the surface, which is unbeneficial to nitrifying biofilm formation. In this study, novel clinoptilolite composite carriers with favorable hydrophilicity, positive charge and nitrification-enhancing capability were made and implemented in IFFAS system. In comparison with conventional carriers, the novel clinoptilolite composite carriers displayed positive charges on the surface (11.7±1.1 mV, pH 7.0) with increased hydrophilicity (surface contact angle dropped to 76.7°). The novel-carriers-based reactors achieved significantly better NH₄⁺-N removal efficiency at different influent concentrations, dissolved oxygen (DO) levels and shock loads (NH₄⁺-N removal efficiency rose up to 20% comparing with the control reactors filled with polyethylene (PE) carriers or activated sludge). High-throughput sequencing (HTS) results indicated the novel clinoptilolite composite carriers provided favorable niche for more types of bacteria, especially for Nitrosomonadales and Nitrospirales (the functional nitrifiers in the system). The population of Nitrospirales increased by 4.51% by using novel clinoptilolite composite carriers comparing with using PE carriers, which ensured enhanced nitrification process. This study was expected to provide a practical option for enhancing wastewater nitrification performance with the novel clinoptilolite composite carrier.