Spatial and temporal distribution of gaseous elemental mercury in Chongqing, China

In order to investigate the spatial and temporal variability of atmospheric mercury (Hg) in Chongqing, China, gaseous elemental mercury (GEM) was measured from August 2006 to September 2007, using Lumex multifunctional mercury analyzer RA-915(+) (Lumex Ltd., Russia). The mean GEM concentration was 6.74 +/- 0.37 ng m(-3) in Chongqing, much higher than the accepted global background values (1.5-2 ng m(-3)). The GEM concentrations were different in different function areas. GEM in transport, industrial and commercial areas were 7.07 +/- 1.04, 7.05 +/- 0.96 and 6.71 +/- 1.10 ng m(-3), respectively, while GEM was 6.14 +/- 1.30 and 4.32 +/- 1.04 in the educational/recreational and nature conservation areas, suggesting that Hg emissions from mobile vehicles and industrial sources (specially coal combustion) were the most important contributors to atmospheric Hg in Chongqing. Mean Hg concentrations also had monthly variations with highest in November (8.24 +/- 0.50 ng m(-3)) and lowest values in August (5.36 +/- 0.70 ng m(-3)). Additionally, the diurnal variation of GEM concentrations was dependent on the local/regional atmospheric conditions. At Jinyun Mountain site (natural conservation area), hourly GEM concentrations had much higher values in daytime than at night. At Power Plant site, however, the hourly GEM concentrations were lower in daytime than at night. GEM concentrations in the air were correlated significantly with meteorological parameters except for barometric pressure.     

A comparison of speciated atmospheric mercury at an urban center and an upwind rural location

Gaseous elemental mercury (GEM), particulate mercury (PHg) and reactive gaseous mercury (RGM) were measured every other hour at a rural location in south central Wisconsin (Devil's Lake State Park, WI, USA) between April 2003 and March 2004, and at a predominantly downwind urban site in southeastern Wisconsin (Milwaukee, WI, USA) between June 2004 and May 2005. Annual averages of GEM, PHg, and RGM at the urban site were statistically higher than those measured at the rural site. Pollution roses of GEM and reactive mercury (RM; sum of PHg and RGM) at the rural and urban sites revealed the influences of point source emissions in surrounding counties that were consistent with the US EPA 1999 National Emission Inventory and the 2003-2005 US EPA Toxics Release Inventory. Source-receptor relationships at both sites were studied by quantifying the impacts of point sources on mercury concentrations. Time series of GEM, PHg, and RGM concentrations were sorted into two categories; time periods dominated by impacts from point sources, and time periods dominated by mercury from non-point sources. The analysis revealed average point source contributions to GEM, PHg, and RGM concentration measurements to be significant over the year long studies. At the rural site, contributions to annual average concentrations were: GEM (2%; 0.04 ng m(-3)); and, RM (48%; 5.7 pg m(-3)). At the urban site, contributions to annual average concentrations were: GEM (33%; 0.81 ng m(-3)); and, RM (64%; 13.8 pg m(-3)).     

南京市冬季大气颗粒态汞的分布特征

采集了南京市2012年冬季4个功能区的PM2．5、PM10、TSP样品，对不同粒径大气颗粒物中的颗粒态汞测试。结果表明，南京冬季大气颗粒物TSP中汞的质量浓度为49．26 pg/m3～257．14 pg/m3，平均质量浓度为161．27 pg/m3；PM10中汞的质量浓度为44．82 pg/m3～228．29 pg/m3，平均质量浓度为147．38 pg/m3；PM2．5中汞的质量浓度为35．98 pg/m3～178．58 pg/m3，平均质量浓度为104．10 pg/m3。不同功能区大气颗粒态汞质量浓度的分布趋势为：交通综合区＞旅游区＞住宿综合区＞商业区。大气颗粒态汞60％以上存在于可吸入肺的PM2．5中，细颗粒物富集汞的能力比粗颗粒物强。     

Mercury wet deposition in rural Korea: concentrations and fluxes

The characteristics of Hg wet deposition were investigated in a rural area of Korea from August 2006 to July 2008. The volume weighted mean (VWM) Hg(T) concentration and cumulative Hg(T) flux were 8.8 ng L(-1) and 9.4 μg m(-2) per year, respectively. The VWM Hg(T) concentration varied seasonally, similar to the seasonal pattern in atmospheric Hg(p) concentration. The enhancement of both VWM Hg(T) and atmospheric Hg(p) concentrations in spring and winter was likely caused by the long-range transport of Hg from China. Monthly VWM Hg(T) and atmospheric Hg(p) concentrations were well correlated (R(2) = 0.36); however, there was no correlation between VWM Hg(T) and RGM (reactive gaseous mercury) concentrations, suggesting that Hg(p) was responsible for the majority of the Hg in wet deposition at this site. The VWM Hg(T) concentration in snow was statistically higher than in rain. In addition, the atmospheric Hg(p) concentration appeared to be elevated for snow events as well. This suggests that both elevated Hg(p) concentrations and the enhanced scavenging efficiency of snow for Hg(p) were responsible for the elevated VWM Hg(T) concentrations measured during snow events.     

Cloud water and throughfall deposition of mercury and trace elements in a high elevation spruce-fir forest at Mt. Mansfield,Vermont

As part of the Lake Champlain Basin watershed study of mercury (Hg) and pollutant deposition, cloud water and cloud throughfall collections were conducted at the south summit (1204 m) of Mt. Mansfield, Vermont between August 1 and October 31, 1998, for multi-element chemical analysis. A passive Teflon string collector was deployed during non-precipitating events to sample cloud/fog water at timberline, while three sets of paired funnels collected cloud throughfall under the red spruce-balsam fir canopy. Samples were analyzed for concentrations of Hg, major ions, and 10 trace elements. Ultra-clean sampling and analysis techniques were utilized throughout the study. Six events were sampled for cloud water alone and four events were sampled for both cloud water and cloud throughfall. Cloud throughfall chemistry showed substantial modification from incident cloud water. Much higher concentrations of Hg (2.3 x), base cations (Ca2+, K-, Mg2+; 3-18 x) and certain trace elements (Ni, Cu, Mn, Rb, Sr; 2-34 x) were observed in throughfall than in cloud water. These results confirm that cloud water can leach a wide variety of elements from tree foliage and wash off dry deposited elements. Cloud water deposited an average of 0.42 +/- 0.12 mm of water per hour. Estimated cloud water deposition of Hg was 7.4 microg m(-2) for the period August 1-October 31, approximately twice that deposited by rain during this period at a nearby low elevation Hg monitoring site. Our results indicate that cloud water and Hg deposition at Mt. Mansfield are likely to have considerable ecological effects.     

Atmospheric-particulates-bound mercury Hg(p) study at five characteristic sampling sites in Taiwan

The main purpose for this study is to observe the seasonal and month variations for particulates-bound mercury Hg(p) in total suspended particulates (TSP) concentration, dry deposition at five characteristic sampling sites during years of 2009-2010 in central Taiwan. The results show that the highest and lowest monthly average particulates-bound mercury Hg(p) concentrations in TSP were occurred in Dec. and Oct. at Gao-mei (wetland), Chang-hua (downtown) and He-mei (residential) sampling site. In addition, the results show that the highest and lowest monthly average particulates-bound mercury Hg(p) dry deposition was occurred in Feb. and Oct. at Quan-xing (industrial) sampling site. This study reflected that the mean highest particulates-bound mercury Hg(p) concentrations in TSP and mean highest particulates-bound mercury Hg(p) dry deposition were occurred at Gao-mei (wetland) and Quan-xing (industrial). However, the mean lowest particulates-bound mercury Hg(p) concentrations in TSP and mean lowest particulates-bound mercury Hg(p) dry deposition were also occurred at Gao-mei (wetland). Regarding seasonal variation, the order of mean-particulates-bound mercury Hg(p) concentrations in TSP in winter and spring were Gao-mei (wetland) > Quan-xing (industrial) > Bei-shi (suburban/coastal) > Chang-hua (downtown) > He-mei (residential). Finally, the order of mean-particulates-bound mercury Hg(p) dry deposition in fall, spring and summer were Quan-xing (industrial) > Bei-shi (suburban/coastal) > Chang-hua (downtown) > He-mei (residential) > Gao-mei (wetland).     

Traffic-related platinum and rhodium concentrations in the atmosphere of Rome

Platinum and Rh content in the atmosphere of Rome as released by car catalytic converters was monitored from 1998 to 2000 in six urban sites with different traffic intensities and in one rural area. Samples collected with medium-volume PM10 samplers were analyzed by Sector Field Inductively Coupled Plasma Mass Spectrometry (SF-ICP-MS). The Pt content varied from 2.4 to 60.1 pg m(-3) (mean value 17.8 pg m(-3)) at the urban locations whilst that of Rh spanned the range 0.8-9.4 pg m(-3) (average value 4.0 pg m(-3)). The rural area showed metal levels mostly below the limits of detection, pointing to automobile traffic as the main source of those elements in the urban atmosphere. The highest mean concentrations of Pt and Rh, ie. 22.2 and 5.0 pg m(-3), were detected along the ring road where the traffic density is high (>100,000 vehicles per day) and the driving speed between 100 and 120 km h(-1). The lowest Pt and Rh mean concentrations, i.e. 11.4 and 3.4 pg m(-3), were measured downtown, where traffic density is lower (20,000 vehicles per day) and the driving speed is limited (50 km h(-1)). Significant concentrations of Pt and Rh were found in the vicinity of traffic signals, indicating that the "stop-and-go" conditions might also affect their release. The measured Pt/Rh ratio spanned the range 3.3-5.9 in accordance with that present in the more commonly used gasoline car catalytic converters. Seasonal variations between wintertime (with Pt and Rh mean concentrations of 23.8 and 5.1 pg m(-3), respectively) and summertime (with Pt and Rh mean concentrations of 14.1 and 3.3 pg m(-3), respectively) were also observed.     

Predominant anthropogenic sources and rates of atmospheric mercury accumulation in southern Ontario recorded by peat cores from three bogs: comparison with natural "background" values (past 8000 years)

Peat cores from three bogs in southern Ontario provide a complete, quantitative record of net rates of atmospheric Hg accumulation since pre-industrial times. For comparison with modern values, a peat core extending back 8000 years was used to quantify the natural variations in Hg fluxes for this region, and their dependence on climatic change and land use history. The net mercury accumulation rates were separated into "natural" and "excess" components by comparing the Hg/Br ratios of modern samples with the long-term, pre-anthropogenic average Hg/Br. The average background mercury accumulation rate during the pre-anthropogenic period (from 5700 years BC to 1470 AD) was 1.4 +/- 1.0 microg m(-2) per year (n = 197). The beginning of Hg contamination from anthropogenic sources dates from AD 1475 at the Luther Bog, corresponding to biomass burning for agricultural activities by Native North Americans. During the late 17th and 18th centuries, deposition of anthropogenic Hg was at least equal to that of Hg from natural sources. Anthropogenic inputs of Hg to the bogs have dominated continuously since the beginning of the 19th century. The maximum Hg accumulation rates decrease in the order Sifton Bog, in the City of London, Ontario (141 microg Hg m(-2) per year), Luther Bog in an agricultural region (89 microg Hg m(-2) per year), and Spruce Bog which is in a comparatively remote, forested region (54 microg Hg m(-2) per year). Accurate age dating of recent peat samples using the bomb pulse curve of 14C shows that the maximum rate of atmospheric Hg accumulation occurred during AD 1956 and 1959 at all sites. In these (modern) samples, the Hg concentration profiles resemble those of Pb, an element which is known to be immobile in peat bogs. The correlation between these two metals, together with sulfur, suggests that the predominant anthropogenic source of Hg (and Pb) was coal burning. While Hg accumulation rates have gone into strong decline since the late 1950's, Hg deposition rates today still exceed the average natural background values by 7 to 13 times.     

大气中不同形态汞的采集和分析方法

作为一种环境优先污染物,汞对人体和其它生物毒性很大。大气是全球汞生物地球化学循环的重要场所。不同形态的汞由于理化性质不同,迁移转化过程及其对生态环境的影响也不同,准确测定大气环境中各种形态的汞对于了解其在大气中的行为具有重要意义。1990年以来,大气汞的采集和分析方法技术已经取得了长足进步,一些自动测汞仪、低汞空白和高时间分辨率的采样及分析技术相继出现,使得准确测定大气中不同形态的痕量汞成为可能。文章就国内外近10多年来在这些方面所取得的研究进展进行了回顾和总结,主要介绍了气态总汞、颗粒态汞、活性气态汞、甲基汞等的采集和分析方法。     

Measurements of gaseous mercury exchanges at the sediment-water, water-atmosphere and sediment-atmosphere interfaces of a tidal environment (Arcachon Bay, France)

The elemental mercury evasion from non-impacted natural areas is of significant importance in the global Hg cycle due to their large spatial coverage. Intertidal areas represent a dynamic environment promoting the transformations of Hg species and their subsequent redistribution. A major challenge remains in providing reliable data on Hg species variability and fluxes under typical transient tidal conditions found in such environment. Field experiments were thus carried out to allow the assessment and comparison of the magnitude of the gaseous Hg fluxes at the three interfaces, sediment-water, sediment-atmosphere and water-atmosphere of a mesotidal temperate lagoon (Arcachon Bay, Aquitaine, France) over three distinct seasonal conditions. The fluxes between the sediment-water and the sediment-atmosphere interfaces were directly evaluated with field flux chambers, respectively static or dynamic. Water-atmosphere fluxes were evaluated from ambient concentrations using a gas exchange model. The fluxes at the sediment-water interface ranged from -5.0 to 5.1 ng m(-2) h(-1) and appeared mainly controlled by diffusion. The occurrence of macrophytic covers (i.e.Zostera noltii sp.) enhanced the fluxes under light radiations. The first direct measurements of sediment-atmosphere fluxes are reported here. The exchanges were more intense and variable than the two other interfaces, ranging between -78 and 40 ng m(-2) h(-1) and were mostly driven by the overlying atmospheric Hg concentrations and superficial sediment temperature. The exchanges between the water column and the atmosphere, computed as a function of wind speed and gaseous mercury saturation ranged from 0.4 to 14.5 ng m(-2) h(-1). The flux intensities recorded over the intertidal sediments periodically exposed to the atmosphere were roughly 2 to 3 times higher than the fluxes of the other interfaces. The evasion of elemental mercury from emerged intertidal sediments is probably a significant pathway for Hg evasion in such tidal environments exhibiting background contamination level.     

A comparison of data quality control protocols for atmospheric mercury speciation measurements

Significant advances in the measurement of atmospheric mercury species have been made in the past 10 years yet limited protocols on quality control (QC) and assurance on this data have been published in the literature. Recently, considerable work has been done to develop quality control and assurance programs within North America. Environment Canada and the National Atmospheric Deposition Network (NADP) independently developed programs, RDMQ? and AMQC, respectively, to QC atmospheric mercury speciation data (including gaseous elemental mercury (GEM), reactive gaseous mercury (RGM) and mercury associated to particles (PHg)). These 2 programs were assessed by the criteria on which the data is QCed and comparability of the final data products. Results show that the criteria used to flag data compare well within the 4 tested sites and that the number of flags for each criterion is generally comparable. The QC programs were applied to 2 distinct data sets and the final QCed data was compared. From a mid-latitude site, the final data sets compare very well and showed there to be a 0.3, 8.6 and 15% difference in the mean GEM, RGM and PHg concentrations post QC of each program. It is recommended that either the RDMQ or the AMQC programs be employed for a typical mid-latitude site. When the QC programs were applied to highly variable data, the data do not compare as well for RGM and PHg. Results showed a 2.7, 27 and 33% difference in the mean GEM, RGM and PHg concentrations, respectively, post QC of each program. It is recommended that RDMQ be used for data that is highly variable with high RGM/PHg concentrations as it allows for more manual correction over the QCed data. This investigation of 2 QC programs produced comparable data and that either of these programs can be used as standard methods for the quality control of atmospheric mercury speciation data.     

Speciation and mass-balance of mercury from pulverized coal fired power plants burning western Canadian subbituminous coals

This report summarizes the results of a study carried out on six pulverized coal-fired power plants in western Canada burning subbituminous coal for the mass-balance and speciation of mercury. The main objectives of this study were to: determine the total gaseous mercury (TGM) emitted from stacks of power plants using the Ontario Hydro method; identify the speciation of emitted mercury such as metallic (Hg(0)) and gaseous elemental (GEM) mercury; and perform mass-balance calculations of mercury for milled-coal, bottom ash, electrostatic precipitators (ESP) fly ash and stack-emitted mercury based on three tests. Sampling of mercury was carried out using the Ontario Hydro method and mercury was determined using the USEPA method 7473 by cold vapor atomic absorption (CVAAS). The sample collection efficiencies confirmed that both oxidized and the elemental mercury had been successfully sampled at all power plants. The total gaseous mercury emitted (TGM) is 6.95-15.66 g h(-1) and is mostly in gaseous elemental mercury (GEM, Hg(0)) form. The gaseous elemental mercury is emitted at a rate of 6.59-12.62 g h(-1). Reactive gaseous mercury (RGM, Hg(2+)) is emitted at a rate of 0.34-3.68 g h(-1). The rate of emission of particulate mercury (Hg(p)) is low and is in the range 0.005-0.076 g h(-1). The range of mass-balances for each power plant is more similar to the variability in measured mercury emissions, than to the coal and ash analyses or process data. The mass-balance calculations for the six power plants, performed on results of the three tests at each power plant, are between 86% and 123%, which is acceptable and within the range 70-130%. The variation in mass-balance of mercury for the six power plants is mostly related to the variability of coal feed rate.     

Polycyclic aromatic hydrocarbons study and toxic equivalency factor (TEFs) in Tehran, IRAN

Polycyclic aromatic hydrocarbons (PAHs) are toxic pollutants released by various urban combustion sources. Benzo[a]pyrene (BaP) is a representative member of the class of PAHs. Health risk assessment associated with inhalatory PAHs uptake is often estimated on the basis of the BaP concentrations in air. Atmospheric particulate PAHs concentrations were measured at five locations in Tehran, Iran. Sixteen PAHs were extracted from the airborne particles and analyzed by HPLC. Total PAHs concentrations (16 compounds) at five station Arjanteen, Enghelab, Azadi, Bahman, Haft Houz were respectively, 70.2, 96.5, 130, 79.1, 44.1 ng/m(3). The information obtain from the present study indicated that mean of human carcinogens are: benzo[a]antheracene (0.17-4.76 ng/m(3)), chrysene (1.74-3.62 ng/m(3)), benzo[b]fluoranthene (0-5.25 ng/m(3)), benzo[k]fluoranthene (0.32-1.72 ng/m(3)), benzo[a]pyrene (1.41-3.82 ng/m(3)), dibenzo[a,h]anthracene (0.33-2.13 ng/m(3)), and indeno[1,2,3-cd]pyrene (0.25-11.08 ng/m(3)). The development and the establishment of a toxicity equivalency factor (TEF) are used in the assessment of mixtures containing PAHs. The contribution of the carcinogenic potency of BaP alone is in the range of 49.6-76.3% of the total carcinogenic activity. The annual number of lung cancer cases (persons per million) among Tehran residents (population = 10 millions) attributable to these carcinogenic PAHs compounds in 2005 was estimated at 58 persons per million. In Tehran urban areas vehicular emission are the primary contributor to PAHs concentrations, with additional local contributors like industrials emissions.     

Hepatic mercury,cadmium, and lead in mink and otter from New York State: monitoring environmental contamination

Many non-linear processes link atmospheric emissions to the bioavailability of metals; consequently, the monitoring of metals in ecosystem components is required to model their ecodynamics. American mink (Neovison vison) and river otter (Lontra canadensis) have the potential to serve as an upper-level-consumer component in monitoring metals bioavailability. However, the relationship of bioaccumulated metals to various environmental factors has not been explored nor have the effects of demographic factors been resolved. To address these limitations, mink and otter, collected throughout New York State during 1998–2002, were analyzed for hepatic concentrations of total mercury (Hg), cadmium (Cd), and lead (Pb). Relationships were investigated between metals concentrations and landscape-level factors (physiographic zone, hydrologic unit, and elevation) and demographic factors (gender and age). Considerable variation in Hg and Cd concentrations was observed relative to both physiographic zone and hydrologic unit for both species. In contrast with Hg, Cd concentration increased predictably with increasing elevation. Mercury concentrations were greater, but for Cd less, in otter than mink. Lead concentrations showed little landscape heterogeneity and were independent of elevation. Age-related bioaccumulation was evident for Hg and Cd, but not for Pb, in both species. Mercury and Cd concentrations were greater in female than male mink; however, Pb concentrations were greater in males than females. Inverse relationships of relative growth (weight/length) to metals concentrations explained gender differences in Hg and Cd in mink. For otter, no gender-related differences in metals concentrations were apparent. The suitability of mink and otter for monitoring programs is discussed.     

Heavy Metals in Liver and Muscle of Bluefin Tuna (Thunnus thynnus) Caught in the Straits of Messina (Sicily, Italy)

The present investigation was carried out on the bluefin tuna (Thunnus thynnus) collected during the month of April 2003 from the Straits of Messina. The aim of this study is to determine heavy metal levels (Cd, Cu, Hg, Mn, Pb and Zn) in liver and muscle tissues of 14 Thunnus thynnus of different age and sex and to investigate the relationships between fish sex and size (length and weight and metal concentrations in the tissues. The concentrations of the various metals were determined by a Varian atomic absorption spectroscopy instrument. The results showsignificant variations (p < 0.01) for Hg and Zn concentrations in muscle than in liver samples. Concentrations of Cd and Pb are below the instrumental detection limits in almost all muscle samples. Levels of Hg (3.03 + 0.55 μg/g) are above the MRLs only in muscle (1μg/g) establishing toxicological risks for the consumer. Regression analysis shows a negative correlation between mercury level and weight and length in samples from both female and male. No significant difference between mean heavy metals concentrations and male or female tuna is seen. For greater food safety, it would be advisable to reduce the mercury intake by selecting safer fish, species and size and by the avoidance of tuna fish consumption by pregnant women, young children and old people, who are more sensitive to mercury exposure.     

Mercury, Methylmercury, and Selenium Concentrations in Eggs of Common Loons (Gavia immer) from Canada

Concentrations of Hg and Se were determined for a total of 125Common Loon (Gavia immer) eggs collected from lakes in Alberta, Saskatchewan, Ontario, Quebec, New Brunswick and NovaScotia, Canada between 1972 and 1997. Resulting data were compared to Hg and/or Se concentrations known or suspected tocause reproductive impairment in birds. Organic (methyl) Hg analyses were also performed on a subset of 24 loon eggs. Thirty-nine of 125 eggs had total Hg levels exceeding those (0.6 g g^-1 ww, or 2.5 g g^-1 dw)previously reported to be associated with reproductive impairment in common loons (Barr, 1986), and 9 of 125 eggshad Hg concentrations higher than the level associated withreproductive impairment in birds generally 1 g g^-1 ww; (Thompson, 1996). Selenium concentrations in loon egg samples were less than levels known to cause reproductiveimpairment in birds. A weak but significant positive correlation was observed between egg-Hg and -Se concentrations(r = 0.511, p < 0.05). On average, methylmercury accounted for about 87% of total Hg in 24 eggs analysed for both total and organic Hg. In this subset of eggs, the relationship between organic (methyl) Hg and Se was significant (r = 0.538, p = 0.007) while that found between inorganic Hg and Se in the same eggs was not significant (r = 0.353, p = 0.091). This relationship was unexpected and was contrary to relationships established for organic and inorganic Hg vs. Se in adult loon liver and kidney tissue (Scheuhammer et al., 1998b).     

In vivo K-shell X-ray fluorescence bone lead measurements in young adults

The (109)Cd K-shell X-ray fluorescence (XRF) technique was used to measure in vivo tibia lead concentrations of 34 young adults living in the state of Vermont (USA) and the province of New Brunswick (Canada). The subjects ranged in age from 18 to 35 years, and had no known history of elevated lead exposure. Measurement parameters were varied, using the same XRF system for both populations. Tibia lead concentrations were low for both groups, with mean values of 0.7 microg lead g(-1) bone mineral (Vermont) and 0.5 microg g(-1)(New Brunswick). No individual measurement exceeded 7 microg g(-1). Mean uncertainty values obtained for the Vermont and New Brunswick subjects were 4.1 microg g(-1) and 2.6 microg g(-1), respectively. Improved measurement uncertainty in the New Brunswick group was attributed to the use of a reduced source-to-skin distance (approximately 5 mm) and a longer measurement time (3600 seconds) using a weaker radioisotope source (< or =0.42 GBq). Measurement uncertainty tended to increase with body mass index. For a given body mass index, female subjects returned a measurement uncertainty approximately 1 microg g(-1) greater than males.     

MULTI-MEDIA CONCENTRATIONS OF HEAVY METALS AND MAJOR IONS FROM URBAN AND RURAL SITES IN NEW BRUNSWICK, CANADA

Concentrations of heavy metals and major ions were measured in precipitation, snowpack, garden soils and vegetables from urban and rural sites in New Brunswick in Atlantic Canada. Atmospheric loading of mercury, lead, cadmium, arsenic, strontium, and vanadium need further assessment. Vanadium concentrations in precipitation, snowpack, soils and vegetables showed an urban influence. Vanadium concentrations in the snowpack ranged between <2.0 ppb at 50 kilometers from the city center to 31.4 ppb in the city. Concentrations of all heavy metals in urban soils were less than CCME remediation guidelines but selected metals exceeded the assessment benchmark non-regulatory guidelines. Major ions were consistently higher in event precipitation than the snowpack. The order of ion elution from the snowpack was NO3 > SO4 > NH4 > H > Mg > Cl > Na > K. Hydrogen ion equivalents were highest in the snowpack and precipitation from urban samples. Mean hydrogen ion concentrations ranged from 11 to 22 eq L-1 in the snowpack compared with 18 to 41 eq L-1 in event precipitation.     

Occurrence of polychlorinated dibenzo-p-dioxins and dibenzofurans (PCDD/Fs), polychlorinated biphenyls (PCBs) and polybrominated diphenyl ethers (PBDEs) in Lake Maggiore (Italy and Switzerland)

Samples of air (gas and particulate phases), bulk deposition, aquatic settling material and sediments were collected in Lake Maggiore (LM) in order to determine their content of polychlorinated dibenzo-p-dioxins and dibenzofurans (PCDD/Fs), polychlorinated biphenyls (PCBs) and polybrominated diphenyl ethers (PBDEs). Air (gas and particulate phases) concentrations were 0.5 pg m(-3), 80 pg m(-3), 13 pg m(-3) and 106 pg m(-3) for SigmaPCDD/Fs, SigmaPCBs, Sigma dioxin-like PCBs (DL-PCBs) and SigmaPBDEs, respectively. Deposition fluxes ranged from 0.7 ng m(-2) d(-1) for SigmaPCDD/Fs to 32 ng m(-2) d(-1) for SigmaPCBs. Aquatic settling material presented concentrations of 0.4 ng g(-1) dry weight (dw) for SigmaPCDD/Fs, 13 ng g(-1) dw for SigmaPCB, 3.4 ng g(-1) dw for SigmaDL-PCBs and 5.7 ng g(-1) dw for SigmaPBDEs. Mean sediment concentrations were 0.4 ng g(-1) dw for SigmaPCDD/Fs, 11 ng g(-1) dw for SigmaPCB, 3 ng g(-1) dw for SigmaDL-PCBs and 5.1 ng g(-1) dw for SigmaPBDEs. Similar PCDD/F and DL-PCB congener patterns in all the environmental compartments of LM point to an important, if not dominant, contribution of atmospheric deposition as source of these pollutants into LM. In contrast, PBDE congener distribution was not similar in the different environmental compartments. BDE 47 dominated air and settling material, while BDE 209 was the predominant congener in the bulk atmospheric deposition. Moreover, sediments showed two distinct PBDE congener profiles. Lower PBDE concentrated sediments were dominated by congeners 47 and 99, while BDE 209 dominated in higher PBDE concentrated samples. This suggests the influence of local sources as well as atmospheric input of PBDEs into LM.     

Rapid,ultra-sensitive detection of gas phase elemental mercury under atmospheric conditions using sequential two-photon laser induced fluorescence

We have examined the sensitivity of sequential two photon laser induced fluorescence (LIF) detection of elemental mercury, Hg(0) in the gas phase. The most sensitive approach involves an initial laser excitation of the 6(3)P1-6(1)S0 transition at 253.7 nm, followed by excitation with a second laser to the 7(1)S0 level. Blue shifted fluorescence is observed on the 6(1)P1-6(1)S0 transition at 184.9 nm. The excitation scheme, involving sequential excitation of two atomic transitions, followed by detection of the emission from a third is extremely specific and precludes detection of anything other than atomic mercury. Using our 10 Hz laser system we have achieved a detection sensitivity of 0.1 ng m(-3) at a sampling rate of 0.1 Hz, i.e. averaging 100 laser shots at a pressure of one atmosphere in air. At low concentrations we sampled simultaneously with an automated mercury analyzer (Tekran 2537A), to ensure accuracy. We have examined the linearity of the technique, generating flows containing mercury concentrations between 1 and 10,000 ng m(-3) using a permeation tube and dynamic dilution, but relying on the concentrations given by the Tekran at low levels and the concentration calculated from dilution at high levels. We find that the detection is linear over the five orders of magnitude that we were able to vary the concentration. Our measured detection limits in He and Ar are much lower as these gases are inefficient fluorescence quenchers.