Screening analysis of volatile organic contaminants in commercial inorganic coagulants used for drinking water treatment

A method for quality screening is suggested to detect volatile impurities in inorganic coagulants that are used for drinking water treatment. Static headspace gas chromatography with mass spectrometry detection (HS–GCMS) is sensitive and selective to detect volatiles in low concentrations. This study has discovered that volatile organic impurities are detectable in ferric and aluminium-based coagulants which are used for drinking water treatment. For ferric chloride, 2-propanol was detected at a level of 17–24 μg ml⁻¹, acetone at 0.7–1.7 μg ml⁻¹, 1,1,1-trichloroacetone at 0.02–0.04 μg ml⁻¹, trichloromethane at 0.01–0.02 μg ml⁻¹ and toluene at 0.01–0.12 μg ml⁻¹. For ferric chloride sulfate, acetone was detected at a level of 0.12 μg ml⁻¹, 1,1,1-trichloroacetone at 0.06–0.08 μg ml⁻¹, trichloromethane at 0.13–0.23 μg ml⁻¹, bromodichloromethane at 0.04–0.06 μg ml⁻¹ and dibromochloromethane at 0.04–0.05 μg ml⁻¹. For aluminium hydroxide chloride, only trichloromethane was detectable, but below the method detection limits (MDL). Although the concentrations of these impurities in commercial coagulants are low, this observation is important and should have impact on water industries for them to pay attention to the chemicals they are using for drinking water production.     

Acid-forming emissions in Alberta,Canada

The sulphur dioxide and nitrogen oxides emissions from all sources in Alberta, Canada, during 1982 amounted to 488,297 and 353,511 tonnes, respectively. During this year deposition of wet sulphate from all stations in the province, 8 kg ha^–1 yr^–1, compares well with the five-year average (1978–1982) value of 10 kg ha^–1 yr^–1. These measurements are about one-half of the wet sulphate deposition criteria of 20 kg ha^–1 yr^–1 established for protecting the moderately sensitive aquatic ecosystem in eastern Canada. Due to dry, cold, continental climate conditions of Alberta, dry sulphate or sulphur deposition is equally or more important than wet deposition. No effects of the long-range transport of atmospheric pollutants (LRTAP) on the ecosystems in Alberta have been observed to date. Atmospheric deposition target loadings of SO₄ ^–2, NO₃ ^–, and H⁺ for Alberta and western Canadian environmental conditions should be developed to protect the highly sensitive ecosystems. Some future research and monitoring priorities for Alberta and western Canada are outlined.     

Role of Alternative Electron Acceptors (AEA) to control methane flux from waterlogged paddy fields: Case studies in the southern part of West Bengal, India

The rice fields, depleted of O₂, contain large amount of moisture and organic substrates to provide an ideal anaerobic environment for methanogenesis and are one of the principal anthropogenic sources of methane. In order to mitigate this emission Alternative Electron Acceptors (AEA) were altered in the soil. The experiments were carried out in four seasons at the site of Balarampur, near Baruipur, South 24 Parganas, West Bengal, namely September–December, 2005 (Cultivar: Sundari), February–May, 2006 (Cultivar: Sundari), September–December, 2006 and February–May, 2007 (Cultivar: Swarna-Pankaj). The seasonal average methane flux (Fe treated), for the cultivar type “Sundari” (season: September–December, 2005), is 4.41 t ha⁻¹, as compared to the value of 6.40 t ha⁻¹ for the untreated soil. Similarly for February–May, 2006, the seasonal average methane flux (Fe treated) is 5.52 t ha⁻¹, whereas the untreated flux is 5.69 t ha⁻¹. In the third and fourth seasons we had two treatments with Ammonium Thiosulphate and Ferric Hydroxide. The seasonal average methane flux (treatment: Ammonium Thiosulphate) is 4.35 t ha⁻¹ and 5.41 t ha⁻¹ respectively, whereas for the ferric hydroxide treated soil it is 4.35 t ha⁻¹ and 6.14 t ha⁻¹ respectively. The properties related to the nutrient quality of the harvested paddy seeds supplement these results.     

Model Computations on Sequestration of Carbon in Managed Forests and Wood Products under Changing Climatic Conditions in Finland

The aim of this study was to assess the effects of forest management on carbon sequestration in forests and wood products by using a gap-type forest model interfaced with a wood product model. The assessment is based on total carbon sequestration, i.e. the amount of carbon left in vegetation, litter, soil organic matter and products when the flows of carbon back to the atmosphere have been subtracted. Thirty mixed-species stands, representing medium fertility sites in southern Finland, were included in each simulation for 300 years under current climatic conditions and predicted conditions of changing climate. The average total balance for the first 100 years was higher in the unmanaged system than in the managed system, but for the second and third 100-year periods the results were clearly opposite. Differences in the total balance between the treatments were larger during the first 100 years than over the whole 300-year period. Under conditions of changing climate, differences in carbon sequestration between management options were more pronounced than under current climatic conditions. Under current climatic conditions with the 100-year time frame, the ratio between the total annual balance and annual gross production was 0·208–0·289. Over the whole 300 years, however, efficiency was much lower, 0·088–0·121. Under changing climatic conditions, efficiency was also lower, 0·182–0·252 and 0·081–0·096, respectively. Different management alternatives clearly produced different amounts of timber for the production process; under conditions of changing climate, timber production was substantially enhanced. However, total carbon storages at the end of the simulation varied less than timber production. In the managed system, the flow back into the atmosphere was largest from litter, 41–51% of the total outflow, the flow from vegetation was 23–28%, from soil organic matter 22–25%, emissions from products 1–7%, and emissions from landfills 0–3%. If emissions due to the use of machinery in timber harvesting and transportation were included, they made up only 0·03–0·33% of the total outflow.     

Impact of crude oil pollution on species number and live standing herbaceous crop biomass

Summary The impact of crude oil spill on the number of plant species and the above-ground live standing crop biomass (AGLSCB) of a herbaceous plant community was assessed. The spillage had a devastating effect on the herbaceous community and especially on the component herbaceous annuals. At least 80–90% of the species were absent in the affected areas in comparison to nearby unaffected areas, most of these being annuals. Perennial species were generally less affected. The total herbaceous production for a period of 12 months in the polluted areas was 885.1 gm^–2 compared with 4860.7 gm^–2 for the unaffected areas. The average monthly production in the polluted areas was 73.8 gm^–2 compared with 405.0 gm^–2 for the unaffected areas.Dr Debojit Baruah is the senior author of this paper and he is a research scholar at Dibrugarh University. Dr Sarada K. Sarma is a Pofessor in the Botany Department of Guwahati University in Assam.     

Natural vs. plantation forests: A case study of land reclamation strategies for the humid tropics

Biomass and productivity were compared in two plantations and in one stand of natural regeneration on similar sites in a premontane moist forest region of Puerto Rico. While initial growth rates of plantation species were higher, after four decades productivity of the natural regeneration plots was equal to or greater than productivity of the plantations. For the first 44 years, aboveground biomass of natural regeneration increased at an average annual rate of 3.8t·ha^–1·yr^–1, but the last year of the study it was 14.7t·ha^–1. Biomass increment of a pine plantation averaged between 8 and 10.5t·ha^–1·yr^–1 except for one year when the rate was much lower, possibly because of hurricane damage. A tropical hardwood plantation averaged close to 4t·ha^–1·yr^–1 for 41 years. It is suggested that in countries where funds for land reclamation are limited, intensive plantations may not always be the best strategy. Natural regeneration or shelterbelt plantations may be suitable alternatives.     

Biomass and nutrient removals from commercial thinning and whole-tree clearcutting of central hardwoods

The objective of this research was to evaluate the impacts of increasing product removal on biomass and nutrient content of a central hardwood forest ecosystem. Commercial thinning, currently the most common harvesting practice in southern New England, was compared with whole-tree clearcutting or maximum aboveground utilization. Using a paired-watershed approach, we studied three adjacent, first-order streams in Connecticut. During the winter of 1981–82, one was whole-tree clearcut, one was commercially thinned, and one was designated as the untreated reference. Before treatment, living and dead biomass and soil on the whole-tree clearcut site contained 578 Mg ha^–1 organic matter, 5 Mg ha^–1 nitrogen, 1 Mg ha^–1 phosphorus, 5 Mg ha^–1 potassium, 4 Mg ha^–1 calcium, and 13 Mg ha^–1 magnesium. An estimated 158 Mg ha^–1 (27% of total organic matter) were removed during the whole-tree harvest. Calcium appeared to be the nutrient most susceptible to depletion with 13% of total site Ca removed in whole-tree clearcut products. In contrast, only 4% (16 Mg ha^–1) of the total organic matter and 2% of the total nutrients were removed from the thinned site. Partial cuts appear to be a reliable management option, in general, for minimizing nutrient depletion and maximizing long-term productivity of central hardwood sites. Additional data are needed to evaluate the long-term impacts of more intensive harvests.     

Three Egyptian industrial wastewater management programmes

A pre-treatment programme for wastewater from factories, representing three main industrial sectors in Egypt, has been developed. The first case study was a factory producing potato-chips. Wastewater discharged from this factory was characterized by high values of BOD, SS and oil and grease (6000 mgO₂ l^–1, 6577 mg l^–1 and 119 mg l^–1 respectively). Chemical treatment using lime and lime aided by polyelectrolyte achieved good results. Residual values of BOD and SS after treatment were 97 mg l^–1 and 49 mg l^–1, respectively. Oil and grease concentrations were reduced by 91 percent. Treatment via activated sludge at a detention time of 4 hrs produced good quality effluent. The second case study was an automobile company, representing the metal finishing industry. Analyses of wastewater samples from the degreasing, phosphating and painting departments, as well as the end-of-pipe effluent were conducted. The end-of-pipe effluent contained high concentrations of oil and grease (366 mg l^–1), phosphorous (111 mg l^–1) and zinc (81 mg l^–1). Chemical treatment of end-of-pipe wastewater using ferric chloride aided by lime, produced high quality effluent. The third sector was the chemical industry. For this purpose a paint factory was selected. Characteristics of raw wastewater varied widely according to the production rate. Average values of COD and BOD were 1950 mg l^–1 and 683 mg l^–1. Oil and grease ranged from 63 to 1624 mg l^–1. Chemical treatment using ferric chloride in combination with lime at the optimum operating conditions achieved good results. Residual values after treatment of COD, BOD and oil and grease reached 120, 36 and 8.6 mg l^–1, respectively. An engineering design for each case study has been prepared.     

Bacterial pretreatment enhances removal of heavy metals during treatment of post-methanated distillery effluent by Typha angustata L

A combination of bacterial pretreatment followed by free water surface flow through wetland plants was investigated to determine its effect on removal of heavy metals in bioremediation of post-methanated distillery effluent (PMDE). The bacterial pretreatment was intended to transform the metal complexes and organic pollutants into simpler, biologically assimilable molecules. The 10% and 30% v/v concentrations of PMDE favored luxuriant bacterial growth; the 50% concentration supported less growth, whereas the undiluted effluent (i.e., 100%) supported very little bacterial growth. The use of bacterial pretreatment combined with the constructed wetland system greatly increase the overall bioaccumulation of all heavy metals by the plants compared with the control treatment. However, the integration of bacterial pretreatment of PMDE with the Typha angustata resulted in enhanced removal of Cd (34.02–61.50% increase), Cr (35.90–57.60% increase), Cu (32.88–54.22% increase), Fe (32.50–51.26% increase), Mn (35.99–82.85% increase), Ni (35.85–59.24% increase), Pb (33.45–59.51% increase) and Zn (31.95–53.70% increase) compared with a control that lacked this pretreatment. In addition to the bioaccumulation of these heavy metals, several physico-chemical parameters also improved at the 30% effluent concentration: color, BOD, COD, phenol and total nitrogen decreased by 98.33%, 98.89%, 98.50%, 93.75% and 82.39%, respectively, after 7 days of free water surface flow treatment. The results suggest that bacterial pretreatment of PMDE, integrated with phytoremediation will improve the treatment process of PMDE and promote safer disposal of this waste.     

Response of Organic and Inorganic Carbon and Nitrogen to Long-Term Grazing of the Shortgrass Steppe

We investigated the influence of long-term (56 years) grazing on organic and inorganic carbon (C) and nitrogen (N) contents of the plant–soil system (to 90 cm depth) in shortgrass steppe of northeastern Colorado. Grazing treatments included continuous season-long (May–October) grazing by yearling heifers at heavy (60–75% utilization) and light (20–35% utilization) stocking rates, and nongrazed exclosures. The heavy stocking rate resulted in a plant community that was dominated (75% of biomass production) by the C₄ grass blue grama (Bouteloua gracilis), whereas excluding livestock grazing increased the production of C₃ grasses and prickly pear cactus (Opuntia polycantha). Soil organic C (SOC) and organic N were not significantly different between the light grazing and nongrazed treatments, whereas the heavy grazing treatment was 7.5 Mg ha^–1 higher in SOC than the nongrazed treatment. Lower ratios of net mineralized N to total organic N in both grazed compared to nongrazed treatments suggest that long-term grazing decreased the readily mineralizable fraction of soil organic matter. Heavy grazing affected soil inorganic C (SIC) more than the SOC. The heavy grazing treatment was 23.8 Mg ha^–1 higher in total soil C (0–90 cm) than the nongrazed treatment, with 68% (16.3 Mg ha^–1) attributable to higher SIC, and 32% (7.5 Mg ha^–1) to higher SOC. These results emphasize the importance in semiarid and arid ecosystems of including inorganic C in assessments of the mass and distribution of plant–soil C and in evaluations of the impacts of grazing management on C sequestration.     

Activated fly ash/slag blended cement

This paper presents the results of the preparation of an ecological cementing material from granulated blast-furnace slag (GBFS) and Class C fly ash (CCFA). The desulphurization gypsum, calcined at 600–800 °C for 0.5–1.5 h, works as the main ingredient of the activator in the cementing material. The optimized formulation of the cementing material was obtained with the aid of factorial design method: slag, 70%; CCFA, 18%; activator, 12%. The “partial super-fine grinding process” was adopted to improve the performance, i.e., 85% of the mixture is ground to Blaine fineness of 3500 cm²/g, 15% further ground to around 5000 cm²/g. The compressive strength of 28 days of the cement mortar is up to 49 MPa and flexural strength 8.4 MPa. The hydration products, investigated by SEM and X-ray diffraction, are mainly ettringite and C–S–H gel.     

Unexpected difference in phenol sorption on PTMA- and BTMA-bentonite

The comparison of phenol sorption on phenyltrimethylammonium (PTMA)- and benzyltrimethylammonium (BTMA)-bentonite shows a clear difference as far as phenol sorption isotherms are concerned. For PTMA-bentonite the sorption isotherm is of a straight-line character which results from simple partitioning of phenol between the aqueous and organic phases sorbed on the bentonite surface. For BTMA-bentonite the isotherm has a convex shape, characteristic of physicochemical sorption.For the first time a three-parametric model, including the dissociation constant of phenol pK_a, distribution constant of phenol Kd_phen and phenolate anion Kd_phen⁻ between the aqueous phase and the bentonite phases is used for the evaluation of phenol sorption on organoclays with pH change. The model shows that the values of Kd_phen are higher than those of Kd_phen⁻ for all investigated initial phenol concentrations.The inspection of the FTIR spectrum of BTMA-bentonite loaded with phenol in the regions 1300–1600 and 1620–1680 cm⁻¹ shows the features of π–π electron interaction between the benzene rings of phenol and the BTMA cation together with the phenol–water hydrogen bond strengthened by this interaction.     

Morphologie effects of channelization: the case of the Neebing-McIntyre floodway,Thunder Bay,Ontario, Canada

The Neebing-McIntyre floodway in Thunder Bay, Ontario, Canada, has been constructed with a relatively straight and uniform trapezoidal channel, compared with the prechannelized sinuous reaches of the Neebing and the McIntyre rivers. The flow regime of the floodway also contrasts significantly with the prechannelized regime, because of the combination of discharges from these rivers into a new channel and the regulation of flows by a diversion structure. The maximum channel capacity of the floodway is about 284 m³ s^–1 (175-year regional flood), compared with about 40 m³ s^–1 and 60 m³ s^–1, respectively, for the Neebing and the McIntyre. According to regime theories, the construction of a straight and trapezoidal channel has upset the equilibrium of the stream system and therefore should lead to some accelerated erosion and sedimentation processes in the new channel immediately after construction. Erosion potential is particularly high during higher discharge events, when flow velocities are expected to be greater than the prechannelized velocities of the Neebing and the McIntyre. The overall sediment yield of the watershed is low (71t km^–2 yr^–1), compared with other documented watersheds of North America, but the rates of deposition in the floodway are relatively high, mainly due to the backwater effect of Lake Superior. Unless maintained by constant channel work, the floodway will tend to fill up with sediment, until a postconstructional equilibrium is reestablished.     

Utilization of waste product (tamarind seeds) for the removal of Cr(VI) from aqueous solutions: Equilibrium, kinetics, and regeneration studies

In the present study, an adsorbent was prepared from tamarind seeds and used after activation for the removal of Cr(VI) from aqueous solutions. The tamarind seeds were activated by treating them with concentrated sulfuric acid (98% w/w) at a temperature of 150 °C. The adsorption of Cr(VI) was found to be maximum at low values of initial pH in the range of 1–3. The adsorption process of Cr(VI) was tested with Langmuir, Freundlich, Redlich–Peterson, Koble–Corrigan, Tempkin, Dubinin–Radushkevich and Generalized isotherm models. Application of the Langmuir isotherm to the system yielded a maximum adsorption capacity of 29.7 mg/g at an equilibrium pH value ranging from 1.12 to 1.46. The adsorption process followed second-order kinetics and the corresponding rate constants obtained were 2.605 × 10⁻³, 0.818 × 10⁻³, 0.557 × 10⁻³ and 0.811 × 10⁻³ g/mg min⁻¹ for 50, 200, 300 and 400 mg/L of initial Cr(VI) concentration, respectively. The regenerated activated tamarind seeds showed more than 95% Cr(VI) removal of that obtained using the fresh activated tamarind seeds. A feasible solution is proposed for the disposal of the contaminants (acid and base solutions) containing high concentrations of Cr(VI) obtained during the regeneration (desorption) process.     

The environmental impact of a chloro-alkali factory in a river basin in Eastern India

Summary It has been established that the electrodes of the dialyser in a chloro-alkali plant in Eastern India release mercury beyond the permissible limits into the River Koel. Mercury in elemental form, as well as certain organo-mercury compounds, including methyl mercury, have been detected at a distance of 25 km from the discharge point. Even at a distance of 5–10 km, the mercury content of the sediment may be as high as 0.6–3.2 mg kg^–1 above the value of sediment upstream of the plant. This sediment itself is contaminated, probably by battery and paint factories, etc., still further upstream. Thus, the chloro-alkali factory has contributed 60–320 times above the permissible limit (0.01 mg kg^–1) of mercury release, at a distance of 5–10 km from the point of release. Furthermore, various phytoplankton and zooplankton have been contaminated, leading to very high mercury contents in certain fish. This food chain, therefore, threatens man himself.Dr Sajalendu Nanda is currently a Research Associate at Bangur Institute of Neurology in Calcutta. He possesses an MSc in Environmental Biology and a PhD in Ecology. His address for correspondence is c/o Dr P.K. Tapaswi, Professor-in-Charge at the Biological Sciences Division of the Indian Statistical Institute.     

Place experience, gestalt, and the human–nature relationship

This paper explores some ways in which differing views about the human–nature relationship reflect and are reflected in people's experiences of the places and environments they encounter in their lives. I first describe how ideas of humans being “part of” versus “apart from” nature have appeared in discussions of environmental ethics and management, and suggest how these contrasting views might relate to people's actual experiences of the natural and human aspects of places. Using qualitative survey responses about outdoor places in the midwestern USA to illustrate ideas from phenomenological and gestalt psychology, I show how a sense of the human–nature relationship is conveyed in the gestalt qualities of places and how this may give rise to a feeling of moral responsibility toward nature. I conclude that the experience of human and natural aspects of real places points toward a dialectical view of the human–nature relationship, in which humans can be seen as simultaneously “part of” and “apart from” nature.     

GIS-based assessment of the threat to world forests by patterns of non-sustainable civilisation nature interaction

The paper presents a novel transdisciplinary approach to investigate non-sustainable civilisation–nature interactions in the context of global change. The approach rests on the decomposition of intricate dynamics of Global Change into problematic patterns civilisation nature interactions (‘syndromes’) this is done by an iterative process of observations, data and theoretical system analysis and GIS-based modelling attempts. These syndromes of global change characterise endangering and risky developments of civilisation nature interaction and represent a baseline for measuring and indicating ‘non-sustainability’; in order to have a sustainable development it is necessary to have a far-reaching absence of syndromes. They encompass the core problems of global change, e.g. soil degradation, climate change, threats to biodiversity or global deforestation. Patterns are defined as characteristic constellations of global change trends (‘symptoms’). Cause–effect schemes of symptoms and their interrelations are constituted as complex phenomena resulting from interactions over the different spheres of the Earth system (biosphere, atmosphere, hydrosphere, population, pedosphere, economy, psychosocial sphere, social organisation, science and technology). The approach is illustrated by an analysis of civilisation–nature interaction patterns relevant for global deforestation. Global forest ecosystems have been chosen for this investigation because of their important role in the global carbon cycle and their importance for biological diversity. The resulting geographical patchwork of the combined dispositions and intensities of the different syndromes describes current and future regional threats to forests by their underlying global cause–effect patterns of civilisation–nature interaction.     

A cost-effective microbial slurry technology for rapid composting of municipal solid wastes in waste dump sites in India and its feasibility for use in Australia

This short article reports on commercial composting slurry now available in India. The slurry culture containing active decomposer bacteria and enzymes is spread on the surface of the garbage and inside the heaps in windrows constructed at waste dump sites. The microbes produce hydrolysing enzymes to break down the long chain complexes of the organic substrates. About 1 kg of slurry culture in the colloidal emulsion form mixed with 20 litres of water is sprayed on about 3 m of solid waste. For one tonne of waste 200 litres of slurry water are needed. The waste heaps are turned once in 7 to 10 days for proper aeration and the inoculant slurry is sprayed at each turning to enhance decomposition and to maintain the proper moisture level which is usually 45–55 percent. The process is exothermic and the windrows reach a temperature of 70°–75°C within 24–36 hours, killing many harmful pathogens and repelling all birds, stray animals, flies and mosquitos from the dump site. The entire process is completed within 4–6 weeks and as the decomposition is completed the temperature falls to normal. About 40–45 percent of the undecomposed matter is of recyclable materials, and of the rest about 25–30 percent requires safe disposal in adjacent land-fill sites. The problem of emission from tip gases and of leachate and discharge of effluents is greatly reduced. The foul odor of the tip also disappears within 2–3 days of sanitization. The compost produced is rich in sodium, potassium and phosphorous as well as certain trace elements, and contains active nitrogen fixing and phosphate solubulising bacteria.     

Effects of nano-SiO(2) and different ash particle sizes on sludge ash-cement mortar

The effects of nano-SiO₂ on three ash particle sizes in mortar were studied by replacing a portion of the cement with incinerated sewage sludge ash. Results indicate that the amount of water needed at standard consistency increased as more nano-SiO₂ was added. Moreover, a reduction in setting time became noticeable for smaller ash particle sizes. The compressive strength of the ash–cement mortar increased as more nano-SiO₂ was added. Additionally, with 2% nano-SiO₂ added and a cure length of 7 days, the compressive strength of the ash–cement mortar with 1 μm ash particle size was about 1.5 times better that of 75 μm particle size. Further, nano-SiO₂ functioned to fill pores for ash–cement mortar with different ash particle sizes. However, the effects of this pore-filling varied with ash particle size. Higher amounts of nano-SiO₂ better influenced the ash–cement mortar with larger ash particle sizes.     

Soil and plant characteristics of landfill sites near Merseyside,England

An ecological survey of the plant and soil characteristics was carried out on three landfill sites near Merseyside, England. It was discovered that bare ground at two of the landfill areas had high levels of methane contained in the soil air (Sefton Meadows landfill: 6–8% at 35 cm and 16–35% at 65 cm below soil surface; Coalgate Lane landfill: 1–24% at 35 cm and 39–45% at 40 cm below soils surface), causing the appearance of dark grey reduced regions in the soil, a phenomenon similar to flooded soil. The wellvegetated areas at the two sites had lower levels of methane (under 7%).In areas relatively free of methane, the concentrations of mineralized N and NO₃ ^– had significant correlations with the dry weights of vegetation (r = 0.71 withp<0.01;r=0.61 withp<0.02 accordingly), indicating the necessity of applying available nitrogen fertilizer.