A field study on phytoremediation of dredged sediment contaminated by heavy metals and nutrients: the impacts of sediment aeration

Compared to traditional chemical or physical treatments, phytoremediation has proved to be a cost-effective and environmentally sound alternative for remediation of contaminated dredged sediment. A field study was conducted in a sediment disposal site predominantly colonized by Typha angustifolia under different sediment moisture conditions to estimate the phytoremediation effects of dredged sediment. The moisture content was 37.30 % and 48.27 % in aerated and waterlogged sediment, respectively. Total nitrogen (TN) content was higher in the waterlogged sediment than in the aerated sediment. The total Cd contents were lower in aerated sediment, which was mainly resulted from the lower exchangeable fraction of Cd. The bioaccumulation of P, Cu and Pb in T. angustifolia was promoted by waterlogging, and the belowground tissue concentrations and accumulation factors (AFs) of Cu were higher than that of other metals, which can be explained by that Cu is an essential micronutrient for plants. Consistent with many previous studies, T. angustifolia showed higher metal levels in roots than in above-ground tissues at both the sediment conditions. Due to the improved biomass produced in the aerated sediment, the removals of nutrients and the metals by plant harvest were higher from aerated sediment than from waterlogged sediment. It was indicated that maintaining the dredged sediment aerated can avoid release risk and plant uptake of metals, while the opposite management option can promote phytoextraction of these contaminants.     

Metal solubility as a function of pH in a contaminated, dredged sediment affected by oxidation

The solubility as a function of pH for metals in a reduced dredged sediment, subjected to different redox conditions, was studied in a laboratory experiment. The redox conditions imposed simulated (i) the undisturbed sediment (flooded), (ii) a dredged material stored in a confined pond (aerated once and then flooded), (iii) an upland stored dredged material (drained and dried), and (iv) an upland stored sediment subjected to tillage (drained, dried and mixed). Minor differences in the solubility as a function of pH were observed between the treatments after two weeks. After three months, the solubility of Cd, Cu, Pb and Zn increased strongly in the oxidized sediments. Leachability of Fe decreased, while Mn, Ni and Co were mostly unaffected. Both short- and long-term mobility of metals (except Fe) is expected to be lowest when a reduced sediment remains in reduced conditions. Studying the solubility as a function of pH may provide additional information on the chemical association of metals in sediments.     

Batch and column studies of the stabilization of toxic heavy metals in dredged marine sediments by hematite after bioremediation

The management of dredged sediments is an important issue in coastal regions where the marine sediments are highly polluted by metals and organic pollutants. In this paper, mineral-based amendments (hematite, zero-valent iron and zeolite) were used to stabilize metallic pollutants (As, Cd, Cu, Mo, Ni, Pb, and Zn) in a contaminated marine sediment sample. Mineral-based amendments were tested at three application rates (5 %, 10 %, and 15 %) in batch experiments in order to select the best amendment to perform column experiments. Batch tests have shown that hematite was the most efficient amendment to stabilize inorganic pollutants (As, Cd, Cu, Mo, Ni, Pb, and Zn) in the studied sediment. Based on batch tests, hematite was used at one application rate equal to 5 % to conduct column experiments. Column tests confirmed that hematite was able to decrease metal concentrations in leachates from stabilized sediment. The stabilization rates were particularly high for Cd (67 %), Mo (80 %), and Pb (90 %). The Microtox solid phase test showed that hematite could decrease significantly the toxicity of stabilized sediment. Based on batch and column experiments, it emerged that hematite could be a suitable adsorbent to stabilize metals in dredged marine sediment.     

Leaching behaviour of Cd, Cu, Pb and Zn in surface soils derived from dredged sediments

Leaching of heavy metals from land-disposed dredged sediment spoils is a potential environmental hazard. The leaching behavior of Cd, Cu, Pb and Zn in surface soils sampled from abandoned dredged sediment disposal sites was assessed. Using simple mass-balance calculations, the significance of the leaching test results with respect to metal migration into underlying clean soil was appraised. The potential leachability, defined as the amounts released at constant pH 4, decreased in the order (% of total contents): Zn (58%) approximately equal to Cd (49%)>Cu (5%) approximately equal to Pb (2%). The kinetics of metal release were determined in a cascade shaking test using de-mineralized water acidified to pH 4 (HNO(3)). Metal concentrations in the leachates were low and metal migration was, assuming uniform convective flow, predicted to be of no environmental concern. It is emphasized that any long-term prediction of metal migration is uncertain.     

Availability of heavy metals for uptake by Salix viminalis on a moderately contaminated dredged sediment disposal site

Extractability of Cd, Cr, Cu, Ni, Pb, and Zn in a dredged sediment disposal site was assessed using single extraction procedures (H2O; 0.01 M CaCl2; 1 M NH4OAc; NH4OAc-EDTA; CaCl2-TEA-DTPA). Only Cd and Zn were found to exceed statutory threshold values for total content. The field was planted with Salix viminalis "Orm" and accumulation of heavy metals in bark, leaves, roots, and wood was evaluated at seven sampling locations along an observed gradient in texture and pollution. Biomass production was high, ranging from 13.2 to 17.8 t ha(-1) y(-1) dry weight. Metal accumulation in aboveground plant parts was low, amounting to the following annually extracted mass of metals per ha: 5034 g Zn, 83 g Cd, 145 g Cu, 83 g Pb, 12 g Ni and 6 g Cr. The use of accumulating clones and the use of soil amendments might enhance extraction efficiency in future research.     

Phytotoxicity of dredged sediment from urban canal as land application

Phytotoxicity of dredged sediment from Hangzhou section of the Grand Canal as land application was evaluated by pakchoi (Brassica chinensis L.) germination tests and pot experiments. Germination rates of pakchoi in the dredged sediment and in sediment-applied soils were both significantly higher than that in the soil controls, while the germination rate between the sediment-applied soils was no significant difference. In pot experiments, plant height and biomass were increased by the dredged sediment application rate in the rate of lower than 540 t ha(-1), but decreased when the application rate was over this rate. Concentrations of Zn and Cu in pakchoi were linearly increased with the increasing of the application rate of the dredged sediment. Both plant height and biomass of pakchoi in sediment-treated red soil were higher than that in sediment-treated paddy soil, regardless the application rate. The results suggest that plant biomass of pakchoi may be used as an indicator of the phytotoxicity of the dredged sediment. It also showed that red soil is more suitable to accept the dredged sediment than paddy soil, and 270 t ha(-1) is a safe application rate both in red soil and paddy soil.     

Declining metal levels at Foundry Cove (Hudson River, New York): response to localized dredging of contaminated sediments

This study examines the effectiveness of remediating a well-recognized case of heavy metal pollution at Foundry Cove (FC), Hudson River, New York. This tidal freshwater marsh was polluted with battery-factory wastes (1953-1979) and dredged in 1994-1995. Eight years after remediation, dissolved and particulate metals (Cd, Co, Cu, Pb, Ni, and Ag) were found to be lower than levels in the lower Hudson near New York City. Levels of metals (Co, Ni, Cd) on suspended particles were comparatively high. Concentrations of surface sediment Cd throughout the marsh system remain high, but have decreased both in the dredged and undredged areas: Cd was 2.4-230mg/kg dw of sediment in 2005 vs. 109-1500mg/kg in the same area in 1983. The rate of tidal export of Cd from FC has decreased by >300-fold, suggesting that dredging successfully stemmed a major source of Cd to the Hudson River.     

Changing contaminant mobility in a dredged canal sediment during a three-year phytoremediation trial

Metal mobility and degradation of organic pollutants were investigated in a contaminated canal sediment in NW England. Sediment was dredged and exposed above the water surface, planted with multiple taxa of Salix, Populus and Alnus and monitored over 32 months. Short-term metal fractionation and phytotoxicity during sediment oxidation were also evaluated in separate laboratory studies. Zinc and Pb redistributed into more mobile fractions, which increased toxicity of the sediment to plants in the laboratory. In contrast, at the canal site, mobility of most elements decreased and total concentrations of Zn, Pb, Cu and Cd fell. Petroleum hydrocarbon concentrations decreased, but the tree-planted treatments appeared less effective at reducing PAH concentrations than treatments colonised by invasive plants. Tree survivorship decreased over time, suggesting increasing phytotoxicity of the exposed sediment in the longer term. Trees provided little benefit in terms of sediment remediation. Options for future management of the sediment are evaluated.     

The effects of dredging and reclamation on metal levels in water and sediments from an estuarine environment off Trinidad, West Indies

The levels of the metals Fe, Cr, Mn, Ni, Pb, Cu and Cd in marine sediments and sea-water were affected differently by dredging and reclamation activities carried out in a shallow coastal bay area. A two way ANOVA showed that the Mn, Ni, Pb and Cd sediment levels in the area sampled during the dredging period were significantly different (p=0.05) from the levels outside the dredging period. The levels obtained at stations along the paths of the undercurrents in the area showed similar variations to the stations close to where the currents originated for most of the metals monitored. This has been attributed to the translocation of loose dredged sediment by current action. The ANOVA also showed that the Ni and Pb sea-water levels obtained within the dredigng period were significantly different (p=0.05) from the levels obtained outside the dredging period. Marked increases in sea-water levels of Cu, Pb, and Ni occurred subsequent to dredging, apparently as a result of oxidative remobilisation of these metals in fill dumped on a reclaimed site in the vicinity. A comparison of the means of both sediment and sea-water levels within and outside the dredging period showed that the Mn sediment and Fe and Cu sea-water means were lower within the dredging period. Only Cd showed no significant difference in sediment levels between sites while CU and Cd showed no significant differences in sea-water levels between sites. Only Ni sediment levels showed a significant site-date interaction.     

Vegetative buffers for fan emissions from poultry farms: 2. ammonia, dust and foliar nitrogen

This study evaluated the potential of trees planted around commercial poultry farms to trap ammonia (NH(3)) and dust or particulate matter (PM). Norway spruce, Spike hybrid poplar, hybrid willow, and Streamco purpleosier willow were planted on five commercial farms from 2003 to 2004. Plant foliage was sampled in front of the exhaust fans and at a control distance away from the fans on one turkey, two laying hen, and two broiler chicken farms between June and July 2006. Samples were analyzed for dry matter (DM), nitrogen (N), and PM content. In addition, NH(3) concentrations were measured downwind of the exhaust fans among the trees and at a control distance using NH(3) passive dosi-tubes. Foliage samples were taken and analyzed separately based on plant species. The two layer farms had both spruce and poplar plantings whereas the two broiler farms had hybrid willow and Streamco willow plantings which allowed sampling and species comparisons with the effect of plant location (control vs. fan). The results showed that NH(3) concentration h(- 1) was reduced by distance from housing fans (P < or = 0.0001), especially between 0 m (12.01 ppm), 11.4 m (2.59 ppm), 15 m (2.03 ppm), and 30 m (0.31 ppm). Foliar N of plants near the fans was greater than those sampled away from the fans for poplar (3.87 vs. 2.56%; P < or = 0.0005) and hybrid willow (3.41 vs. 3.02%; P < or = 0.05). The trends for foliar N in spruce (1.91 vs. 1.77%; P = 0.26) and Streamco willow (3.85 vs. 3.33; P = 0.07) were not significant. Pooling results of the four plant species indicated greater N concentration from foliage sampled near the fans than of that away from the fans (3.27 vs. 2.67%; P < or = 0.0001). Foliar DM concentration was not affected by plant location, and when pooled the foliar DM of the four plant species near the fans was 51.3% in comparison with 48.5% at a control distance. There was a significant effect of plant location on foliar N and DM on the two layer farms with greater N and DM adjacent to fans than at a control distance (2.95 vs. 2.15% N and 45.4 vs. 38.2% DM, respectively). There were also significant plant species effects on foliar N and DM with poplar retaining greater N (3.22 vs. 1.88%) and DM (43.7 vs. 39.9%) than spruce. The interaction of location by species (P < or = 0.005) indicated that poplar was more responsive in terms of foliar N, but less responsive for DM than spruce. The effect of location and species on foliar N and DM were not clear among the two willow species on the broiler farms. Plant location had no effect on plant foliar PM weight, but plant species significantly influenced the ability of the plant foliage to trap PM with spruce and hybrid willow showing greater potential than poplar and Streamco willow for PM(2.5)(0.0054, 0.0054, 0.0005, and 0.0016 mg cm(- 2); P < or = 0.05) and total PM (0.0309, 0.0102, 0.0038, and 0.0046 mg cm(- 2), respectively; P < or = 0.001). Spruce trapped more dust compared to the other three species (hybrid willow, poplar, and Streamco willow) for PM(10) (0.0248 vs. 0.0036 mg cm(- 2); P < or = 0.0001) and PM(> 10) (0.0033 vs. 0.0003 mg cm(- 2); P = 0.052). This study indicates that poplar, hybrid willow, and Streamco willow are appropriate species to absorb poultry house aerial NH(3)-N, whereas spruce and hybrid willow are effective traps for dust and its associated odors.     

Changes in Chlorinated Organic Pollutants and Heavy Metal Content of Sediments during Pyrolysis (7 pp)

Background There has been an increasing concern about the treatment and disposal of contaminated sediment from dredged river, harbor or estuary due to the accumulated toxic organics such as dioxins and inorganics particularly heavy metals like Cr, Pb, Zn, Cu, Hg and Cd. However, considering the huge amount of materials and financial costs involved, any candidate technology must ultimately result to reusable residual by-products. This can only be made possible if the toxic pollutants are removed or stabilized in the raw sediment and then fed back into the materials cycle. Currently, we are developing a pyrolysis process for the commercial-scale cleanup of dioxins and heavy metal-contaminated river sediment to yield reusable char for various economical applications. In this connection, this paper describes our preliminary investigation into the extent of dioxins and heavy metal volatilization from actual contaminated sediment. The stabilization of certain metallic species particularly Cr ions was studied. Methods Laboratory scale pyrolysis experiments were conducted using a special horizontal lab-scale pyrolyzer. Sediment samples from Shanghai Suzhou Creek and Tagonoura Harbor were pyrolyzed in the reactor under nitrogen gas at 800°C and different retention times of 30, 60 and 90 min. A constant heating rate of 10°C min-1 was employed. The pyrolysis gas was first allowed to pass through a cold trap to condense the tar. Uncondensed gases were then channeled through a column containing an adsorbent (XAD-2 Resin) for dioxins. Heavy metal concentrations in the initial and final sediment residues were analyzed by ICP (Nippon Jarrel-Ash) following their acid and alkali (for Cr6+) digestion. Dioxins content of the pyrolysis char, tar, and exhaust gases in the dioxin adsorbent were also determined. For comparative purpose, thermal treatment under air flow was conducted. Results The data for the removal of heavy metals from Suzhou Creek sediment showed very significant reductions in Pb, Zn and Cr6+ content of the sediment at this condition. Percentage removals were 42.4%, 60.8% and 42.2%, respectively. The disappearance of Cr6+ was due to reduction reactions rather than volatilization since the total Cr content remained almost unchanged. Other heavy metals such as Cu, Fe and Ni showed very minimal reductions. Nonetheless, Toxicity Characteristics Leaching Procedure (TCLP) tests confirmed that these residual heavy metals were rather stable in the pyrolysis char. Reduction of toxic Cr6+ at 42.2% has also been achieved by pyrolysis (with N2) as opposed to the more than 580 % increase in Cr6+ observed during thermal oxidation (with air). Discussion Pyrolysis also remove toxic organics particularly dioxins from the sediment. For the total dioxins, removal percentage of 99.9999% was achieved even at the lowest retention time of 30 min. Almost all polychlorinated dibenzo-p-dioxine (PCDDs) and polychlorinated dibenzo-furans (PCDFs) were removed at any retention time. The TEQs detected from the solid residues were mainly contributed by dioxin-like PCBs, yet these were present in relatively trace quantities. At the shortest retention time of 30 min, only 0.000085 pg-TEQ g-1 of polychlorinated biphenyls (PCBs) was detected in the pyrolysis char. Furthermore, the residual PCBs have very low toxicity ratings and none of the highly toxic PCBs, which were initially present in the sediment such as 3,3',4,4',5-PeCB and 3,3',4,4'5,5'-HxCB, were detected in the char. Results further confirmed that most of the dioxins that were removed were transferred to the gas phase so that volatilization may be considered as the main mechanism for their removal. Conclusion Some heavy metals particularly Pb and Zn can be volatilized under N2 pyrolysis at 800oC. Pyrolysis also prevented the formation of more toxic Cr6+ ions and at the same time resulted to its reduction by around 42.2% contrast to the 580% increase during thermal oxidation. PCDDs and PCDFs have been removed and were not formed in the solid products over the retention time range of 30-90 min at 800°C. Dioxin-like PCBs mostly remained and a retention time of 30 min was found sufficient for its maximum removal. Recommendations and Perspective . With the above results, a temperature of 800oC at a retention time of 30 min is sufficient for the removal of total dioxins and some heavy metals by volatilization. It is however necessary to destroy the dioxins as well as recover heavy metals in the gas phase. Stability of remaining heavy metals in the char also needs to be confirmed by leaching tests. These are the major concerns, which we are currently evaluating to establish the feasibility of our proposed large scale pyrolysis system for sediment treatment.     

Evaluating contamination of dredges and disposal criteria in Greek coastal areas

Sediments were collected from areas that were going to be dredged located at six small Greek ports, as well as from possible disposal areas. In order to assess the contamination level of dredged material, the samples were analysed for pH, organic matter, the metals Cd, Pb, Hg, Cr, Ni, Cu, Zn and major organic compounds (PAHs, PCBs). The sediments' quality was evaluated by two approaches: (i) by classifying each area according to two sets of Sediment Quality Guidelines (SQGs) and (ii) by calculating the contamination factors and degree for each area. The results showed that organic compounds were detected in trace amounts in 14% of the port samples belonging to the PAHs group. The characterization of the sediment samples was based on the metals' concentration showing that the majority of the areas to be dredged (80%) are classified as of medium-low contamination according to the SQGs. However, according to the contamination degree, only 30% of the areas are classified as of low contamination, while 40% as of moderate contamination and 30% of the areas as of considerable contamination. From the point of view of "no disturbance" of the ecosystem, decisions about dumping should be taken only after evaluating the material to be dredged. If the SQGs are exceeded, dumping must be forbidden. Otherwise, further evaluation is needed based on the comparison with the receiving area, i.e. by estimating the contamination degree. Dumping could be allowed if the contamination degree is found to be below moderate.     

Using Various Guidelines and Approaches for the Assessment of Marine Sediment Quality

The aim of the present study is to explore the implications of using different quality guidelines and approaches for marine sediment characterization. As a case study, the sediments of Souda Port, Crete, Greece, were examined in order to assess heavy metal contamination and to estimate anthropogenic contribution and potential adverse effects to aquatic environment, as well as to indicate feasible future management options. The concentration of six heavy metals (Co, Cr, Cu, Ni, Pb, and Zn) was determined and compared with different sediment quality guidelines (SQGs) and regional/national criteria established for dredged material characterization and management. In addition, the geo-accumulation index (I_geo) was calculated and the sediments toxicity and heavy metals bioavailability were determined. Based on the experimental data, it is deduced that Souda sediments are characterized as moderately polluted only in terms of Co, Ni, and Pb.     

Phosphorus and copper leaching from dredged sediment applied on a sandy loam soil: column study

In this paper, downward movement of phosphorus and copper as dredged sediment applied on sandy loam soil was studied by column leaching experiments. Three sediment application rate, (i.e., 1, 2 and 5-cm depth of sediments) were applied to the top of the soil columns. Two and a half months leaching experiments were conducted, which include a 15-day un-watered period. Concentrations of phosphorus and copper in the leachate and the vertical distribution of Olsen-P and diethylenetriaminepentaacetic acid (DTPA) extractable Cu in the soil columns were determined. The results showed that, un-watered period could increase the downward movements of phosphorus and copper. Sediment application significantly increased Olsen-P concentration in the top 15 cm of the soil columns, but has not significantly affected that in the deeper soil layer. The 1-cm depth sediment treatment did not increase the DTPA extractable Cu concentration in the whole soil column. The 5-cm depth sediment treatment, however, significant increased the DTPA extractable Cu in the deeper soil layers. This study suggested that the application of dredged sediment laden with P and Cu on sandy loam soil might cause the significant downward movement of phosphorus and copper.     

Changes in the leachability of metals from dredged canal sediments during drying and oxidation

The behaviour of metals in canal sediments after their disposal to land has important implications for the environmental management of canal dredgings. The leaching behaviour of trace metals was investigated in a laboratory-based experiment using sediment from a canal in the UK (139 mg Zn kg-1dry sediment, 1.1 mg Cd, kg-1dry sediment 31.5 mg Cr kg-1dry sediment, 20.6 mg Cu kg-1dry sediment 48.4 mg Ni kg-1dry sediment, 43.4 mg Pb kg-1dry sediment and 7.6 mg As kg-1dry sediment). The sediment was allowed to dry. Cores (10 cm long) of the drying canal sediment were taken over a period of 12 weeks. A simple water extraction procedure was used to investigate changes in metal leachability at varying depths through the cores. Metal leachability increased over the first five weeks of drying and then subsequently decreased between weeks five and twelve, (e.g. Cd increased from approximately 0.006 to 0.018 mg/kgsediment then decreased to approximately 0.006 mg/kgsediment, Zn increased from approximately 1.5 to 3 mg/kgsediment and then decreased to approximately 1.5 mg/kgsediment). These results were combined with sulphide/sulphate ratios, which showed a decrease as the sediment dried (e.g. at 2-4 cm depth from approximately 1 to 0.49), and BCR sequential extraction data. Most metals (except Cd and As) showed a redistribution from the residual phase into more mobile phases as the sediment dried and oxidised. Metal leachability was strongly correlated with the sulphide/sulphate ratio with leachability normally increasing with decreasing sulphide/sulphate ratio. The combined results were used to infer the likely behaviour of dredged material upon disposal to land.     

Potential sensitivity of mires to drought,acidification and mobilisation of heavy metals: the sediment s/(Ca + Mg) ratio as diagnostic tool

In recent decades sulphate concentrations in the ground water in many parts of The Netherlands have increased dramatically resulting in increased production of iron-(di)sulphides in sediments of ecosystems fed by this water. A sediment survey was carried out to study the potential sensitivity of wetlands to drought and subsequent acidification as a consequence of iron-(di)sulphide oxidation. Dessication led to severe acidification and mobilisation of heavy metals when the sediment S/(Ca + Mg) ratio exceeded 2/ 3. A total of 47% of the investigated locations contained S/(Ca + Mg) ratios higher than 2/3 and in 100, 75 and 50% of the locations mobilisation of Zn, Cd and Ni exceeded the Dutch signal value for ground water. Consistent with the sediment survey, lime addition experiments confirmed that increasing the buffer capacity, down to a S/(Ca + Mg) ratio 2/3, led to a drastic inhibition of the acidification and heavy metal percolation from dredged sediments. The performance of the same processes under drained field conditions demonstrates the relevance of these processes during dry summers.     

Experimental determination of efficiency of capping materials during consolidation of metal-contaminated dredged material

Capping has received considerable attention as a method to reduce contaminant transport from contaminated sediments and sub-aqueous disposed dredged materials. Consolidation of dredged material after capping can result in a substantial advection of pore water, into or through the capping layer. The effect of two different capping materials (crushed limestone and gneiss) on the transport of heavy metals and phosphorus during consolidation was studied with a novel experimental design. Capped dredged material was placed in a consolidation cell and pore water expelled during the consolidation was collected for chemical analysis. To support interpretation of the results from this test, interactions between the capping material and the dredged material were also studied in batch tests. The study revealed large differences in the capping efficiency (CE) between the two materials. Both materials were efficient caps for Fe and P (CE>99% with 2cm cap), while limestone also was efficient for Mn (CE>92% with 2cm cap). Contrary to what was expected, capping of dredged material with crushed gneiss increased the release of Ca, Mn, Co, Ni, Cd, and Cu, resulting in negative CE. The batch tests showed that leaching from the crushed gneiss was the source of the observed release of metals. The results also show that the high concentrations of heavy metals in the dredged material were immobilised, probably by sulphides. Protection against re-suspension and oxidation will therefore in many cases be the most important effect of the cap.     

城市河涌受污染底泥的固化/稳定化处理

为了给河涌疏浚底泥的资源化提供技术支持,以广州市车陂涌表层受污染底泥为研究对象,用水泥、石灰、粉煤灰、膨润土等材料对底泥进行固化/稳定化处理实验。通过无侧限抗压强度、污染物在模拟自然条件下(中性)的释放特征、毒性浸出实验(酸性条件)对固化/稳定化处理效果进行综合分析。结果表明:经合适的处理后,固化体抗压强度能高于300 kPa;固化体自然条件下重金属的释放量明显减少,固化/稳定化处理能够有效减缓和减少固化体的二次污染;毒性浸出实验结果表明,河涌底泥经固化/稳定化处理后其重金属浸出能力显著降低。     

Vegetative buffers for fan emissions from poultry farms: 2. ammonia,dust and foliar nitrogen

This study evaluated the potential of trees planted around commercial poultry farms to trap ammonia (NH₃) and dust or particulate matter (PM). Norway spruce, Spike hybrid poplar, hybrid willow, and Streamco purpleosier willow were planted on five commercial farms from 2003 to 2004. Plant foliage was sampled in front of the exhaust fans and at a control distance away from the fans on one turkey, two laying hen, and two broiler chicken farms between June and July 2006. Samples were analyzed for dry matter (DM), nitrogen (N), and PM content. In addition, NH₃ concentrations were measured downwind of the exhaust fans among the trees and at a control distance using NH₃ passive dosi–tubes. Foliage samples were taken and analyzed separately based on plant species. The two layer farms had both spruce and poplar plantings whereas the two broiler farms had hybrid willow and Streamco willow plantings which allowed sampling and species comparisons with the effect of plant location (control vs. fan). The results showed that NH₃ concentration h^{? 1} was reduced by distance from housing fans (P ≤ 0.0001), especially between 0 m (12.01 ppm), 11.4 m (2.59 ppm), 15 m (2.03 ppm), and 30 m (0.31 ppm). Foliar N of plants near the fans was greater than those sampled away from the fans for poplar (3.87 vs. 2.56%; P ≤ 0.0005) and hybrid willow (3.41 vs. 3.02%; P ≤ 0.05). The trends for foliar N in spruce (1.91 vs. 1.77%; P = 0.26) and Streamco willow (3.85 vs. 3.33; P = 0.07) were not significant. Pooling results of the four plant species indicated greater N concentration from foliage sampled near the fans than of that away from the fans (3.27 vs. 2.67%; P ≤ 0.0001). Foliar DM concentration was not affected by plant location, and when pooled the foliar DM of the four plant species near the fans was 51.3% in comparison with 48.5% at a control distance. There was a significant effect of plant location on foliar N and DM on the two layer farms with greater N and DM adjacent to fans than at a control distance (2.95 vs. 2.15% N and 45.4 vs. 38.2% DM, respectively). There were also significant plant species effects on foliar N and DM with poplar retaining greater N (3.22 vs. 1.88%) and DM (43.7 vs. 39.9%) than spruce. The interaction of location by species (P ≤ 0.005) indicated that poplar was more responsive in terms of foliar N, but less responsive for DM than spruce. The effect of location and species on foliar N and DM were not clear among the two willow species on the broiler farms. Plant location had no effect on plant foliar PM weight, but plant species significantly influenced the ability of the plant foliage to trap PM with spruce and hybrid willow showing greater potential than poplar and Streamco willow for PM_2.5(0.0054, 0.0054, 0.0005, and 0.0016 mg cm^{? 2}; P ≤ 0.05) and total PM (0.0309, 0.0102, 0.0038, and 0.0046 mg cm^{? 2}, respectively; P ≤ 0.001). Spruce trapped more dust compared to the other three species (hybrid willow, poplar, and Streamco willow) for PM₁₀ (0.0248 vs. 0.0036 mg cm^{? 2}; P ≤ 0.0001) and PM_{> 10} (0.0033 vs. 0.0003 mg cm^{? 2}; P = 0.052). This study indicates that poplar, hybrid willow, and Streamco willow are appropriate species to absorb poultry house aerial NH₃–N, whereas spruce and hybrid willow are effective traps for dust and its associated odors.