Explosibility of fine graphite and tungsten dusts and their mixtures

To evaluate the explosion hazard of ITER-relevant dusts, a standard method of 20-l-sphere was used to measure the explosion indices of fine graphite and tungsten dusts and their mixtures. The effect of dust particle size was studied on the maximum overpressures, maximum rates of pressure rise, and lower explosive concentrations of graphite dusts in the range 4 μm to 45 μm. The explosion indices of 1 μm tungsten dust and its mixtures with 4 μm graphite dust were measured. The explosibility of these dusts and mixtures were evaluated. The dusts tested were ranked as St1 class. Dust particle size was shown to be very important for explosion properties. The finest graphite dust appeared to have the lowest minimum explosion concentration and be able to explode with 2 kJ ignition energy.     

Explosibility of hydrogen–graphite dust hybrid mixtures

To evaluate the hazard of combined hydrogen/dust explosions under severe accident conditions in International Thermonuclear Experimental Reactor (ITER), standard method of 20-L-sphere was used to measure the explosion indices of 4-μm fine graphite dust in lean hydrogen/air mixtures. The mixtures were ignited by a weak electric spark. The tested fuel concentrations were 8–18 vol% H₂ and 25–250 g/m³ dust. If the hydrogen content is higher than 10 vol%, the dust constituent can be induced to explode by the hydrogen explosion initiated by a weak electric spark. Depending on the fuel component concentrations, the explosions proceed in either one or two stages. In two-stage explosions occurring at low hydrogen and dust concentrations, the mixture ignition initiates first a fast hydrogen explosion followed by a slower phase of the dust explosion. With increasing dust concentration, the dust explodes faster and can overlap the hydrogen-explosion stage. At higher hydrogen concentrations, the hybrid mixtures explode in one stage, with hydrogen and dust reacting at the same time scale. Maximum overpressures of hybrid explosions are higher than those observed with hydrogen alone; maximum rates of pressure rise are lower in two-phase explosions and, generally, higher in one-stage explosions, than those characteristic of the corresponding H₂/air mixtures.     

Explosibility of cork dust in methane/air mixtures

Explosibility studies of hybrid methane/air/cork dust mixtures were carried out in a near-spherical 22.7 L explosibility test chamber, using 2500 J pyrotechnic ignitors. The suspension dust burned as methane/air/dust clouds and the uniformity of the cork dust dispersion inside the chamber was evaluated through optical dust probes and during the explosion the pressure and the temperature evolution inside the reactor were measured. Tested dust particles had mass median diameter of 71.3 μm and the covered dust cloud concentration was up to 550 g/m³. Measured explosions parameters included minimum explosion concentration, maximum explosion pressures and maximum rate of pressure rise. The cork dust explosion behavior in hybrid methane/air mixtures was studied for atmospheres with 1.98 and 3.5% (v/v) of methane. The effect of methane content on the explosions characteristic parameters was evaluated. The conclusion is that the risk and explosion danger rises with the increase of methane concentration characterized by the reduction of the minimum dust explosion concentration, as methane content increases in the atmosphere. The maximum explosion pressure is not very much sensitive to the methane content and only for the system with 3.5% (v/v) of methane it was observed an increase of maximum rate of pressure rise, when compared with the value obtained for the air/dust system.     

磨细粉煤灰自动装车除尘系统的研制

针对磨细粉煤灰由储料仓向罐式汽车内装料的作业特点,研制了自动化装车除尘系统,解决了装车过程中的粉尘污染问题,并实现了装车过程的自动化。     

攀钢发电厂粉煤灰的利用

介绍了粉煤灰的产生过程和特性 ,以及水泥型粉煤灰的生产工艺。简述了新型粉煤灰混凝土混合比试验 ,分析了水泥型粉煤灰利用的经济效益     

Explosibility of polyamide and polyester fibers

The current research is aimed at investigating the explosion behavior of hazardous materials in relation to aspects of particulate size. The materials of study are flocculent (fibrous) polyamide 6.6 (nylon) and polyester (polyethylene terephthalate). These materials may be termed nontraditional dusts due to their cylindrical shape which necessitates consideration of both particle diameter and length. The experimental work undertaken is divided into two main parts. The first deals with the determination of deflagration parameters for polyamide 6.6 (dtex 3.3) for different lengths: 0.3 mm, 0.5 mm, 0.75 mm, 0.9 mm and 1 mm; the second involves a study of the deflagration behavior of polyester and polyamide 6.6 samples, each having a length of 0.5 mm and two different values of dtex, namely 1.7 and 3.3. (Dtex or decitex is a unit of measure for the linear density of fibers. It is equivalent to the mass in grams per 10,000 m of a single filament, and can be converted to a particle diameter.) The explosibility parameters investigated for both flocculent materials include maximum explosion pressure (P_max), size-normalized maximum rate of pressure rise (K_St), minimum explosible concentration (MEC), minimum ignition energy (MIE) and minimum ignition temperature (MIT). ASTM protocols were followed using standard dust explosibility test equipment (Siwek 20-L explosion chamber, MIKE 3 apparatus and BAM oven). Both qualitative and quantitative analyses were undertaken as indicated by the following examples. Qualitative observation of the post-explosion residue for polyamide 6.6 indicated a complex interwoven structure, whereas the polyester residue showed a shiny, melt-type appearance. Quantitatively, the highest values of P_max and K_St were obtained at the shortest length and finest dtex for a given material. For a given length, polyester displayed a greater difference in P_max and K_St at different values of dtex than polyamide 6.6. Long ignition delay times were observed in the BAM oven (MIT measurements) for polyester, and video framing of explosions in the MIKE 3 apparatus (MIE measurements) enabled observation of secondary ignitions caused by flame propagation after the initial ignition occurring at the spark electrodes.     

Explosibility of micron- and nano-size titanium powders

Explosibility of micron- and nano-titanium was determined and compared according to explosion severity and likelihood using standard dust explosion equipment. ASTM methods were followed using a Siwek 20-L explosion chamber, MIKE 3 apparatus and BAM oven. The explosibility parameters investigated for both size ranges of titanium include explosion severity (maximum explosion pressure (P_max) and size-normalized maximum rate of pressure rise (K_St)) and explosion likelihood (minimum explosible concentration (MEC), minimum ignition energy (MIE) and minimum ignition temperature (MIT)). Titanium particle sizes were ?100 mesh (<150 μm), ?325 mesh (<45 μm), ≤20 μm, 150 nm, 60–80 nm, and 40–60 nm. The results show a significant increase in explosion severity as the particle size decreases from ?100 mesh with an apparent plateau being reached at ?325 mesh and ≤20 μm. Micron-size explosion severity could not be compared with that for nano-titanium due to pre-ignition of the nano-powder in the 20-L chamber. The likelihood of an explosion increases significantly as the particle size decreases into the nano range. Nano-titanium is very sensitive and can self-ignite under the appropriate conditions. The explosive properties of the nano-titanium can be suppressed by adding nano-titanium dioxide to the dust mixture. Safety precautions and procedures for the nano-titanium are also discussed.     

Explosibility and thermal decomposition behavior of nitrile rubber dust in industrial processes

The formation of nitrile rubber (NBR) dust clouds during processing can lead to a potential dust explosion under certain conditions. However, the potential explosion hazard posed by NBR dust is usually overlooked by enterprises. In this paper, the explosive properties of NBR dust are investigated using a Hartmann tube, a G-G furnace, and a 20 L explosion chamber. The results showed that NBR dust could cause explosions severe enough to be classified as St-1. In addition, the thermal decomposition behavior of NBR dust under combustion conditions was investigated using a combination of thermogravimetric analysis coupled with Fourier transform infrared spectroscopy (TGA-FTIR). The results indicated that in the early stage, NBR dust mainly undergoes self-thermal decomposition to produce a large amount of combustible gas, which combines with oxygen to form a mixed gas and cause a gas-phase explosion. In addition, the participation of oxygen could lower the initial temperature of NBR dust thermal decomposition. As a result, decomposition occurred more quickly and a large amount of combustible gas was produced, thus expanding the range of dust explosions. Furthermore, these combustible gases exhibit varying degrees of toxicity, seriously affecting the life and health safety of relevant personnel. This work provides theoretical guidance for the development of safe procedures to prevent and address problems during NBR dust processing in enterprises.     

Prediction of flammability limits of fuel-air and fuel-air-inert mixtures from explosivity parameters in closed vessels

Flammability limits of fuel-air and fuel-air-inert gaseous mixtures, especially at non-atmospheric conditions, are essential properties required for establishing safety operating conditions for handling and processing flammable gases. For pure fuels, an important data pool exists, formed by the flammability limits of fuel-air and fuel-air-inert gaseous mixtures at ambient initial conditions measured by standard methods. Such methods can be used for experimental determination of flammability limits for multi-fuels mixed with air, with or without additives, under non-atmospheric conditions. Their use is however a time- and material-consuming process; in addition, the flammability limits obtained by various standard methods may be scattered as a result of different choices in the operating parameters, for each standard method. It appears that a preliminary estimation of the flammability limits for fuel-air and fuel-air-inert gaseous mixtures can minimize the effort of measuring them in specific initial conditions.The present paper describes a new method for estimating the flammability range of fuel-oxidizer gaseous mixtures based on measurements of explosivity properties e.g. the peak explosion pressure and maximum rate of pressure rise recorded during closed vessel laminar explosions of fuel-oxidizer mixtures far from limits. Data obtained for several hydrocarbon-air gaseous mixtures with or without inert gas addition are used to examine the accuracy of estimated flammability limits (LFL – the lower and UFL – the upper flammability limit) as well as of the Limiting Oxygen Concentration (LOC) and the Minimum Inert Concentration (MIC). The predictive ability of the proposed method is examined against the predictive ability of other recently described methods.     

Explosibility,flammability and the thermal decomposition of Bisphenol A,the main component of epoxy resin

Bisphenol A is one of the basic compounds used in a synthesis of polycarbonates and epoxy resins. Its dust can create an explosive mixture with air under specific circumstances. Therefore, the main goal of this research was to determine explosion characteristics and flammability behaviour of this compound. The complete flammability characteristic requires the determination of the basic parameters of Bisphenol A under fire conditions including Heat Release Rate, speed of combustion, ability to ignite and the temperature of the decomposition range. To establish those parameters, a cone calorimeter was used. The explosion characteristics were tested in a 20-L spherical vessel. Minimum Ignition Energy was tested on MINOR II Apparatus which is a modified Hartman's Tube. In order to identify hazardous substances generated during a fire involving Bisphenol A, a simultaneous thermal analysis that combines thermogravimetry and differential scanning calorimetry was used. The substances obtained from the thermal degradation were analyzed by infrared spectroscope with Fourier transformation. Furthermore, the application of a Purser furnace and gas chromatography with mass spectrometry facilitated the identification of gaseous substances formed during the thermal degradation of Bisphenol A samples.     

影响飞机燃油箱惰化系统参数的数值研究

选取单个飞机燃油箱,运用CFD方法模拟了燃油箱惰化系统的惰化过程。CFD方法的模拟结果与文献中的理想混合模型及经验公式吻合较好。通过模拟,发现增加富氮气体的流量、提高富氮气体中的氮气含量可以缩短惰化时间,而增加富氮气体喷嘴直径和燃油箱的体积则会延长惰化时间。其他参数如燃油箱的形状和富氮气体喷嘴位置对惰化时间没有明显的影...     

Effect of spark duration on explosion parameters of methane/air mixtures in closed vessels

The paper outlines an experimental study on influence of the spark duration and the vessel volume on explosion parameters of premixed methane–air mixtures in the closed explosion vessels. The main findings from these experiments are: For the weaker ignition the spark durations in the range from 6.5 μs to 40.6 μs had little impact on explosion parameters for premixed methane–air mixtures in the 5 L vessel or 20 L vessel; For the same ignitions and volume fractions of methane in air the explosion pressures and the flame temperatures in both vessels of 5 L and 20 L were approximately the same, but the rates of pressure rises in both vessels of 5 L and 20 L were different; The explosion indexes obtained from the measured pressure time histories for both vessels of 5 L and 20 L were approximately equal; For the weaker ignition with the fixed spark duration 45 μs the ignition energies in the range from 54 mJ to 430 mJ had little impact on the explosion parameters; For the same ignition and the volume fractions of methane in air, the vessel volumes had a significant impact on the flame temperatures near the vessel wall; The flame temperatures near the vessel wall decreased as the vessel volumes increased.     

Limit of safety against flame transmission for sintered metal flame arrester elements in the case of flashback in fuel gas/oxygen mixtures

In autogenous welding, cutting and allied processes, so-called dry safety devices are used to protect the outlet terminals of gas distribution lines. To prevent flame transmission, these units are fitted with sintered metal flame arrester elements. At the Federal Institute for Materials Research and Testing (BAM), extensive investigations have been carried out with an experimental flame arrester to determine the limits of safety against flame transmission for sintered metal flame arrester elements in the case of flashback in fuel gas/oxygen mixtures. On the basis of the results of these investigations, it is possible to estimate the pore sizes up to which a sintered metal element can prevent any flame transmission with a given fuel gas.     

Determination of explosion parameters of methane-air mixtures in the chamber of 40 dm3 at normal and elevated temperature

The experimental results of the measurements of the explosion pressure and rate of explosion pressure rise as a function of molar methane concentration in the mixture with air in the 40 dm³ explosion chamber are presented. The research was aimed at determination of the explosion limits, according to the EU Standard. The influence of initial temperature of the mixture (changing in the range of 293–473 K) on the fundamental explosion parameters was also investigated. The ignition source was an induction electrical spark of the power equal to approximately 10 W. It was stated, that the increase of initial temperature of the methane-air mixture causes a significant increase of the explosion range.     

Flash points measurements and prediction for binary miscible mixtures

Flash point is one of the most important parameters used to characterize the potential fire and explosion hazards for flammable liquids. In this study, flash points of twenty eight binary miscible mixtures comprised eighteen flammable pure components with different compositions were measured by using the closed cup apparatus. The obtained experimental data are further employed to develop simple and accurate models for predicting the flash points of binary miscible mixtures. Based on the vapor–liquid equilibrium theory, the normal boiling point, the standard enthalpy of vaporization, the average number of carbon atoms, and the stoichiometric concentration of the gas phase were selected as the dominant physicochemical parameters that were relevant to the overall flash point property of liquids. With these parameters for pure components as well as the compositions of mixtures, the new form of characteristic physicochemical parameters for mixtures were developed and used as the input parameters for the flash point prediction of mixtures. Both the modeling methods of multiple linear regression (MLR) and multiple nonlinear regression (MNR) were employed to model the possible quantitative relationships between the parameters for mixtures and the flash points of binary miscible mixtures. The resulted models showed satisfactory prediction ability, with the average absolute error for the external test set being 2.506 K for the MLR model and 2.537 K for the MNR model, respectively, both of which were within the range of the experimental error of FP measurements. Model validation was also performed to check the stability and predictivity of the presented models, and the results showed that both models were valid and predictive. The models were further compared to other previously published models. The results indicated the superiority of the presented models and revealed which can be effectively used to predict the FP of binary miscible mixtures, requiring only some common physicochemical parameters for the pure components other than any experimental flash point or flammability limit data as well as the use of the Le Chatelier law. This study can provide a simple, yet accurate way for engineering to predict the flash points of binary miscible mixtures as applied in the assessment of fire and explosion hazards and the development of inherently safer designs for chemical processes.     

Database for accidents and incidents in the fuel ethanol industry

The purpose of the present research is to collect information about accidents and incidents that have occurred at fuel ethanol facilities from 1998 to October 2014, and to keep complete unified records of them in a database. The developed database contains general information about the accident or incident, its sequence, mitigation measures, its causes and consequences for humans, environment and for the plant. Until now, this information is not available. The work consisted in gathering information from different documental sources and subsequent organization in a database. It complements the previous work made for biodiesel industry and fills the existing gap in the field of ethanol. Knowledge about this information enables us to manage plant risks, since the accidents that are more likely to occur and the main sources of risk can be easily identified. Also, it makes it possible to exchange information with interested third parties. Statistical analysis shows that accident frequency has an oscillatory behavior, rising in the last year. Fire is the most common type of accident, while equipment mechanical failure is the main cause of accident. Partial material loss has been identified as the most common consequence. Finally, some conclusions are obtained concerning to the importance of having an updated and complete accident and incident database.     

Motorcycle fuel tanks and pelvic fractures: A motorcycle fuel tank syndrome

Objective: Pelvic injuries are a serious and commonly occurring injury to motorcycle riders involved in crashes, yet there has been limited research investigating the mechanisms involved in these injuries. This study aimed to investigate the mechanisms involved in pelvic injuries to crashed motorcyclists.

Method: This study involved in-depth crash investigation and 2 convenience-based data sets were used. These data sets investigated motorcycle crashes in the Sydney, Newcastle, and Adelaide regions. Participants included motorcycle riders who had crashed either on a public road or private property within the study areas. The mechanism of injury and the type of injuries were investigated.

Results: The most frequent cause of pelvic injuries in crashed motorcyclists was due to contact with the motorcycle fuel tank during the crash (85%). For riders who had come into contact with the fuel tank, the injury types were able to be grouped into 3 categories based on the complexity of the injury. The complexity of the injury appeared to increase with impact speed but this was a nonsignificant trend. The pelvic injuries that did not occur from contact with the fuel tank in this sample differed in asymmetry of loading and did not commonly involve injury to the bladder. They were commonly one-sided injuries but this differed based on the point of loading; however, a larger sample of these injuries needs to be investigated.

Conclusion: Overall improvements in road safety have not been replicated in the amelioration of pelvic injuries in motorcyclists and improvements in the design of crashworthy motorcycle fuel tanks appear to be required.     

煤粉燃烧性与工业分析、着火温度的相关性研究

喷吹煤粉燃烧性是生产中的一个重要参数,实时掌握原煤燃烧性的波动变化对保证喷煤的安全和稳定十分必要。直接测量煤粉燃烧性的方法成本高,时间长,操作复杂,不利于生产应用;采用测定煤的工业分析和着火温度的方法简单易行,应用范围广泛。该文针对某炼铁厂的15种原煤,进行了工业分析和着火温度的实验研究,引入了统计学中相关系数的概念对数据进行了处理分析,实验证明煤的挥发分和着火温度与煤粉的燃烧性高度线性相关,此方法为利用两参数间接分析煤粉燃烧性提供了理论基础。