Characterization of Compost from a Pilot Plant-scale Composter Utilizing Simulated Solid Waste

A pilot plant-scale composter using simulated solid waste was developed to test the fate of consumer products such as disposable diapers. The simulated waste consisted of a mixture of rabbit chow (which included alfalfa), shredded newspaper, sand, and composted cow manure. The compost mass self-heated from an ambient temperature of 27°C to about 55°C in the first 24 h. Dissolved ammonia levels, high in the early stages of the process, began to decrease after about 4 weeks as nitrate concentration began to increase. Both volatile solids and carbon:nitrogen ratios exhibited gradual decreases with time. Microbial biomass, esterase activity, cellulose mineralization, direct microscopic counts (AODC), and relative APIZYM enzyme activity increased significantly in the first several days, and maintained higher levels than initial measurements throughout the 22-week testing period. We concluded that the simulated solid waste underwent physical, chemical, and microbiological changes that would be expected to occur in municipal solid waste in a full-scale composting system. The pilot plant-scale composter should prove to be a valuable tool in assessing the fate of products and materials under simulated compost conditions.     

Agricultural waste as household fuel: Techno-economic assessment of a new rice-husk cookstove for developing countries

In many rural contexts of the developing world, agricultural residues and the organic fraction of waste are often burned in open-air to clear the lands or just to dispose them. This is a common practice which generates uncontrolled emissions, while wasting a potential energy resource. This is the case of rice husk in the Logone Valley (Chad/Cameroon). In such a context household energy supply is a further critical issue. Modern liquid fuel use is limited and traditional solid fuels (mainly wood) are used for daily cooking in rudimentary devices like 3-stone fires, resulting in low efficiency fuel use, huge health impacts, increasing exploitation stress for the local natural resources. Rice husk may be an alternative fuel to wood for household energy supply. In order to recover such a biomass, the authors are testing a proper stove with an original design. Its lay-out (featuring a metal-net basket to contain the fuel and a chimney to force a natural air draft) allows a mix of combustion/gasification of the biomass occurring in a completely burning fire, appropriate for cooking tasks. According to results obtained with rigorous test protocols (Water Boiling Test), different lay-outs have been designed to improve the performance of the stove. Technical and economic issues have been addressed in the development of such a model; building materials have been chosen in order to guarantee a cost as low as possible, using locally available items. The feasibility of the introduction of the stove in the studied context was assessed through an economic model that keeps into account not only the technology and fuel costs, but also the energy performance. According to the model, the threshold for the trade-off of the stove is the use of rice husk to cover 10–15% of the household energy needs both with traditional fireplaces or with improved efficiency cookstoves. The use of the technology proposed in combination with improved woodstove would provide householders with an appropriate and convenient cooking technology portfolio, increasing the opportunities of choice of the preferred energy system for the user and allowing significant savings for the family budget (up to 50% of the total annual cooking energy expenditure). The proposed model may be used also as a tool for the evaluation of the affordability or for the comparison of different cooking technologies also in other similar contexts, given their specific techno-economic parameter values.     

Food waste treatment in a community center

For urban community composting centers, the proper selection and use of bulking agent is a key element in not only the cost but also the quality of the finished compost. Besides wood chips (WC) widely used as BA, readily usable cereal residue pellets (CRP) can provide biodegradable carbon and sufficient free air space (FAS) to produce stabilizing temperatures. The objective of the present project was to test at a community center, the effectiveness of CRP in composting food waste (FW). Two recipes were used (CRP with and without WC) to measure: FAS; temperature regimes, and; losses in mass, water, carbon and nitrogen. Both recipes were composted during three consecutive years using a 2 m³ commercial in-vessel composter operated in downtown Montreal (Canada). For all recipes, FAS exceeded 30% for moisture content below 60%, despite yearly variations in FW and BA physical properties. When properly managed by the center operator, both FW and CRP compost mixtures with and without WC developed within 3 days thermophilic temperatures exceeding 50 °C. The loss of total mass, water, carbon and nitrogen was quite variable for both recipes, ranging from 36% to 54%, 42% to 55%, 48% to 65%, and 4% to 55%, respectively. The highest loss in dry mass, water and C was obtained with FW and CRP without WC aerated to maintain mesophilic rather than thermophilic conditions. Although variable, lower nitrogen losses were obtained with CRP and WC as BA, compared to CRP alone, as also observed during previous laboratory trials. Therefore and as BA, CRP can be used alone but nitrogen losses will be minimized by adding WC. Compost stabilization depends on operator vigilance in terms of aeration. The measured fresh compost density of 530-600 kg/m³ indicates that the 2 m³ in-vessel composter can treat 6.5 tons of FW/year if operated during 7 months.     

Open windrow composting of polymers: an investigation into the operational issues of composting polyethylene (PE)

This paper investigates the operational issues surrounding the open windrow composting of degradable polyethylene sacks. Areas for consideration were the impact of degradable polyethylene sacks on the composting process, the quality of the finished compost product, and how the use of sacks influenced the on-site processing. These factors were investigated through determining the amount of polymer residue and chemical contaminants in the finished compost product and the daily monitoring of windrow temperature profiles. Site and practical handling considerations of accepting an organic waste contained within PE sacks are also discussed. Statistical analysis of the windrow temperature profiles has led to the development of a model that can help to predict the expected trends in the temperature profiles of open compost windrows where the organic waste is kerbside collected using a degradable PE sack.     

Effect of the mixing ratio on the composting of OFMSW digestate: assessment of compost quality

This study presents the results obtained in compostability tests of organic fraction of municipal solid waste (OFMSW) digestate. The final aim was to obtain mature compost without phytotoxic effects. For the evaluation of the composting process, a novel parameter describing the performance of the composting process, the relative heat generation standardized with the initial volatile solid content (RHGVS₀), was defined and evaluated at laboratory-scale. From these laboratory-scale test, the optimum operational conditions were obtained, a mixing ratio (v/v) of 1:1:0 (bulking agent:digestate:co-substrate) and with 15% of mature compost as inoculum. Subsequently, these optimum operational conditions were applied in the active phase of the composting pilot-scale reactor. The active composting stage took 7 days, subsequently a curing phase of 60 days was carried out at ambient conditions. After 30 days of curing, the mature compost showed a specific oxygen uptake rate (SOUR) of 0.14 mg O₂/g VS·h, a germination index (GI) of 99.63% and a low volatile fatty acids (VFA) concentration (41.3 AcH mg/kg_dm), being indicative of the good compost stability and maturity of the compost. The very good quality of the final compost obtained indicated that the RHGVS₀ accurately describes the performance of the composting process.

     

Survey of composition and generation rate of household wastes in Beijing, China

It is recognized that information on both quantity and composition of residential waste is important for the effective planning of household waste handling infrastructure. In this paper, we present the results of a survey on household waste generation and composition in Beijing, China. Sample communities were selected by the integration of five indices including family population, income, age, and education. Wastes were sampled on a daily basis from 113 households in six different districts of Beijing City for ten days. The results showed that the generation rate of household wastes was 0.23 kg/pers/day. The bulk density was approximately 221 kg/m³, and the moisture content was approximately 50%. Household waste consisted of kitchen waste, paper/cardboard, plastics, textiles, metals, glass and other wastes, the proportion of each waste was approximately 69.3%, 10.3%, 9.8%, 1.3%, 0.8%, 0.6% and 2.7%, respectively. An evaluation of the relationship between daily per capita generation of household waste and socio-economic factors indicated that household size and income both showed a negative relationship with household waste generation (kg/pers/day). As for the effect of education, families with a secondary educational level produced fewer household wastes (kg/pers/day) than those with a primary or advanced educational level.     

Compact fluorescent lights and the impact of convenience and knowledge on household recycling rates

Increased energy costs, social marketing campaigns, public subsidies, and reduced retail prices have dramatically increased the number of compact fluorescent lights (CFLs) installed worldwide. CFLs provide many benefits, but they contain a very small amount of mercury. Given the billions of CFLs in use worldwide, they represent a significant source of mercury unless CFLs are recycled and the mercury recovered in an environmentally sound manner. In the state of Maine (northeast United States), despite mandated recycling of CFLs and availability of free CFL recycling, the household CFL recycling rate is very low. A study was undertaken to identify the primary factors responsible for low recycling. The first step was to survey householders who use CFLs. The 520 survey responses indicated that insufficient knowledge regarding recycling and inconvenience of the collection system are the two primary factors for the low recycling rate. To validate these findings, the second step was an examination of the current collection system to assess (a) the knowledge requirements necessary for recycling and (b) the convenience of the collection system. The results of this examination validated that knowledge requirements were excessively difficult to fulfill and the collection system is not sufficiently convenient. Based on these results, waste managers should focus on increasing convenience and simplifying access to information when designing or improving household collection and recycling of CFLs.     

Sources and levels of potentially toxic elements in the biodegradable fraction of autoclaved non-segregated household waste and its compost/digestate

Waste that reflected the average UK composition of household waste was treated by autoclaving at the three set pressure/temperature levels of 2.7 bar/130 degrees C, 6.2 bar/160 degrees C and 15.5 bar/200 degrees C. The biodegradable fraction of the autoclaved household waste (;floc') was manually separated by screening and underwent characterization for its Cd, Cr, Cu, Pb, Hg, Ni, and Zn content. Autoclaving did not guarantee the production of compost/digestate that met the UK specification for compost, BSi PAS100, without restrictions being made on the composition of the waste feedstock. Results indicate that the levels of Zn and Cd associated with floc materials alone could lead to compost limit values being exceeded. For all other potentially toxic elements (PTEs), the estimated excessive (i.e. above levels of compliance) PTEs levels for compost/digestate were mainly due to external (i.e. non-floc) materials, primarily electronic/electrical waste. Batteries may have also contributed to the high levels of Zn and Hg. In this study, for all PTEs examined, with the exception of Cd and Zn, autoclaving had a performance comparable to that of the most effective mechanical biological treatment systems.     

Effect of light Sphagnum peat on odour formation in the early stages of biowaste composting

In the present study, we investigated the effects of two bulking materials, Sphagnum peat and pine wood chips, on the early stages of biowaste composting in two pilot-scale processes. Emphasis was placed on studying the formation conditions of malodorous compost gases in the initial phases of the processes. The results showed that gas emission leaving an open windrow and a closed drum composting system contained elevated concentrations of fermentative microbial metabolites when acid Sphagnum peat (pH 3.2) was used as a bulking material. Moreover, the gas emission of the peat amended drum composter contained a high concentration of odour (up to 450,000 ou m^?3 of air). The highest odour values in the outlet gas of peat amended composts coincided with the elevated concentrations of volatile organic compounds such as acetoin and buthanedion. We conclude that the acidifying qualities of composting substrates or bulking material may intensify odour emission from biowaste composts and prolong the early stages of the composting process.     

Substitution of peat,fertiliser and manure by compost in hobby gardening: User surveys and case studies

Four user surveys were performed at recycle centres (RCs) in the Municipalities of Aarhus and Copenhagen, Denmark, to get general information on compost use and to examine the substitution of peat, fertiliser and manure by compost in hobby gardening. The average driving distance between the users’ households and the RCs was found to be 4.3 km and the average amount of compost picked up was estimated at 800 kg per compost user per year. The application layer of the compost varied (between 1 and 50 cm) depending on the type of use. The estimated substitution (given as a fraction of the compost users that substitute peat, fertiliser and manure with compost) was 22% for peat, 12% for fertiliser and 7% for manure (41% in total) from the survey in Aarhus (n = 74). The estimate from the survey in Copenhagen (n = 1832) was 19% for peat, 24% for fertiliser and 15% for manure (58% in total). This is the first time, to the authors’ knowledge, that the substitution of peat, fertiliser and manure with compost has been assessed for application in hobby gardening. Six case studies were performed as home visits in addition to the Aarhus surveys. From the user surveys and the case studies it was obvious that the total substitution of peat, fertiliser and manure was not 100%, as is often assumed when assigning environmental credits to compost. It was more likely around 50% and thus there is great potential for improvement. It was indicated that compost was used for a lot of purposes in hobby gardening. Apart from substitution of peat, fertiliser and manure, compost was used to improve soil quality and as a filling material (as a substitute for soil). Benefits from these types of application are, however, difficult to assess and thereby quantify.     

Study on the quality and stability of compost through a Demo Compost Plant

This study is concerned with the performance of a Demo Compost Plant for the development of acceptable composting technology in Bangladesh. The Demo Compost Plant was setup at the adjacent area of an existing compost plant located at Khulna city in Bangladesh. Four different composting technologies were considered, where Municipal Solid Waste (MSW) were used as a raw material for composting, collected from the adjacent areas of the plant. Initially the whole composting system was conducted through two experimental setups. In the 1st setup three different types of aerators (horizontal and vertical passively aerator and forced aerator) were selected. For a necessary observation four piles, using only MSW as the input materials in the first three compost pile, the fourth one was the existing Samadhan’s compost pile. Based on the analysis of the experimental findings, the horizontal passively aerated composting technique is suitable for Bangladesh as it had better performance for reducing composting period than that of the others. It was being observed from the quality parameters of compost in the both 1st and 2nd setup that as the waste directly come from kitchen, degradation rate of waste shows a positive result for reducing this waste and there is no possibility of toxic contamination, when it would be used as a soil conditioner. Though there is no significant improvement in the quality of the final product in the 2nd setup as comparing with the 1st setup but it fulfills one of the main objectives of this study is to reduce the whole composting period as well as immediate management of the increasing amount of waste and reducing load on landfill. Selfheating tests reveal that degree of stability of compost with respect to maturation period was remained in the acceptable level, which was further accelerated due to the use of organic additives.     

Effect of vermiculite addition on compost produced from Korean food wastes

To evaluate the effect of vermiculite addition on composting food wastes from Korean households, food wastes were composted in three small bins to which different additives were added. The following three bins were employed: in Case I, only recycled compost was composted; in Case II, food wastes with recycled compost; and in Case III, food wastes with recycled compost and vermiculite. In the experiment performed for 30 days, it was confirmed that the supplementary addition of vermiculite to the composting mixture did not significantly improve the weight loss rate and the decomposition rate of food wastes. Due to dilution through the use of inorganic vermiculite, the vermiculite addition reduced the organic matter concentration of the composting mixtures. Vermiculite addition did not raise the pH value. Weight losses of roughly 70% were observed based on calculating moisture loss as well as dry food waste loss and not considering additives, while dry food waste loss was 29.4% and 35.8% with and without the addition of vermiculite, respectively. For these experiments, the major portion of the weight loss was the loss of water. The results indicate a need to differentiate between weight loss percentages and decomposition percentages, and a need to indicate if either of these percentages includes or excludes the mass of additives.     

Home composting versus industrial composting: Influence of composting system on compost quality with focus on compost stability

Stability is one of the most important properties of compost obtained from the organic fraction of municipal solid wastes. This property is essential for the application of compost to land to avoid further field degradation and emissions of odors, among others. In this study, a massive characterization of compost samples from both home producers and industrial facilities is presented. Results are analyzed in terms of chemical and respiration characterizations, the latter representing the stability of the compost. Results are also analyzed in terms of statistical validation. The main conclusion from this work is that home composting, when properly conducted, can achieve excellent levels of stability, whereas industrial compost produced in the studied facilities can also present a high stability, although an important dispersion is found in these composts. The study also highlights the importance of respiration techniques to have a reliable characterization of compost quality, while the chemical characterization does not provide enough information to have a complete picture of a compost sample.     

The potential of financial incentives to enhance householders' kerbside recycling behaviour

Although the successful enhancement of householders' participation in kerbside recycling schemes is essential for household waste recycling schemes to reach their desired levels of achievement, our understanding of householders' responses to the various incentives available to waste managers is incomplete. In particular, whether and how the recycling behaviour of householders may be favourably altered through imposition of financial penalties or rewards is not fully understood. Surveys of householders' attitudes in the London Borough of Havering, served by a kerbside co-mingled survival bag recycling scheme, showed they might be better encouraged to recycle more through improvements to structural and promotional aspects of the recycling scheme than through imposition of financial incentives. If financial incentives were to be imposed to enhance kerbside recycling, householders preferred: (1) rewards to penalties, and (2) community-based rewards and local taxation rebates to other or individual rewards. Given the attitudes of householders and the resources that would be needed to monitor their recycling behaviour as a basis for delivering financial incentives, it is suggested that the priority for enhancing recycling should be to make appropriate improvements in the infrastructure and support of the kerbside scheme and service.     

In-vessel composting of household wastes

The process of composting has been studied using five different types of reactors, each simulating a different condition for the formation of compost; one of which was designed as a dynamic complete-mix type household compost reactor. A lab-scale study was conducted first using the compost accelerators culture (Trichoderma viridae, Trichoderma harzianum, Trichorus spirallis, Aspergillus sp., Paecilomyces fusisporus, Chaetomium globosum) grown on jowar (Sorghum vulgare) grains as the inoculum mixed with cow-dung slurry, and then by using the mulch/compost formed in the respective reactors as the inoculum. The reactors were loaded with raw as well as cooked vegetable waste for a period of 4 weeks and then the mulch formed was allowed to maturate. The mulch was analysed at various stages for the compost and other environmental parameters. The compost from the designed aerobic reactor provides good humus to build up a poor physical soil and some basic plant nutrients. This proves to be an efficient, eco-friendly, cost-effective, and nuisance-free solution for the management of household solid wastes.     

Physical analyses of compost from composting plants in Brazil

Nowadays the composting process has shown itself to be an alternative in the treatment of municipal solid wastes by composting plants. However, although more than 50% of the waste generated by the Brazilian population is composed of matter susceptible to organic composting, this process is, still today, insufficiently developed in Brazil, due to low compost quality and lack of investments in the sector. The objective of this work was to use physical analyses to evaluate the quality of the compost produced at 14 operative composting plants in the Sao Paulo State in Brazil. For this purpose, size distribution and total inert content tests were done. The results were analyzed by grouping the plants according to their productive processes: plants with a rotating drum, plants with shredders or mills, and plants without treatment after the sorting conveyor belt. Compost quality was analyzed considering the limits imposed by the Brazilian Legislation and the European standards for inert contents. The size distribution tests showed the influence of the machinery after the sorting conveyer on the granule sizes as well as the inert content, which contributes to the presence of materials that reduce the quality of the final product.     

Household food waste separation behavior and the importance of convenience

Two different strategies aiming at increasing household source-separation of food waste were assessed through a case-study in a Swedish residential area (a) use of written information, distributed as leaflets amongst households and (b) installation of equipment for source-segregation of waste with the aim of increasing convenience food waste sorting in kitchens. Weightings of separately collected food waste before and after distribution of written information suggest that this resulted in neither a significant increased amount of separately collected food waste, nor an increased source-separation ratio. After installation of sorting equipment in households, both the amount of separately collected food waste as well as the source-separation ratio increased vastly. Long-term monitoring shows that results where longstanding. Results emphasize the importance of convenience and existence of infrastructure necessary for source-segregation of waste as important factors for household waste recycling, but also highlight the need of addressing these aspects where waste is generated, i.e. already inside the household.     

Estimating the quantity of solid waste generation in Oyo, Nigeria.

The study established waste multipliers that could be used in conjunction with the population figure of a city to estimate the quantity of solid waste generation in the developing world. Oyo, a traditional city in Nigeria was the focus of the study. Two sets of data were collected. The first was the information on the socio-economic attributes of residents obtained from 648 households through questionnaires administered using a systematic random sampling technique. The second was the measurement of waste generated in 25% of the households for a week in each of the 12 months of the year. The study established that 23.3% of the residents surveyed have educational qualifications beyond secondary school, with 51.2% engaged in occupations requiring very little or no formal education and 50.9% were in the low-income group. The daily per capita solid waste generation was 0.129 kg. The highest (9.8%) and lowest (6.5%) of the annual quantities of waste were produced in October and February, respectively. Similarly, 20.2% of the weekly generation was produced on Saturday and the 10.2% produced on Thursday was the lowest. Animal dung, which accounted for 18.0%, constituted the highest component of the total solid waste generated. The study further established that the organic component of the waste generation was 75.4%. The results of the regression analysis R2 significant at 0.001 showed that income, household size, social status, occupation, education and season of the year explained 88.8% of waste generation in Oyo. It was established that 50.90 tonnes of solid waste was generated per day in the city in 2005, and the daily generation in the year 2008 is estimated to be 55.20 tonnes. The study concluded that with an average annual population growth of 13 000 people for the town, an additional 1.3 acres of land will need to be legally acquired annually, implying that 10.92-19.68 hectares ill be required as dump site(s) over the next 20-30 years.     

Comprehensive quality assessment of municipal organic waste composts produced by different preparation methods

In the first part of this work, the effect of municipal organic waste (MOW) composts on plant growth was evaluated in a greenhouse trial. The treatments included soil amended with 14 different composts (prepared by shredding, adding wood shavings, cocomposting with biosolids or vermicomposting), an inorganically fertilized soil, and a control soil. All of the treatments significantly increased plant growth compared to the control, and yields of three of the amended treatments were as high as that of the inorganic fertilizer treatment. When comparing differently prepared composts to the conventional compost, it was found that cocomposting MOW with biosolids was the method which most positively influenced yields (26-41% yield increases). In the second part of this work, we evaluated the effects of the different preparation methods on compost quality, using a multivariate approach. Three main quality aspects were considered collectively in a principal component analysis: organic matter and nutrient concentrations, degradability and capacity to mineralize these nutrients, and plant growth. The model was restricted to the first and second components (PC1 and PC1) which accounted for 94% of data variance. On the resulting factorial plane, four groups were distinguished. Each of the groups was compared to the reference compost to determine quality increases or decreases. Based on this analysis, it was found that cocomposting MOW with biosolids produced the highest quality products (higher total nutrient and OM concentration, nutrient mineralization potential, and plant growth). Addition of wood shavings increased OM concentration, but reduced quality in terms of the other aspects studied. Shredding was only effective to increase product quality when it was not combined with other methods, whereas vermicomposting only increased quality when MOW was not mixed with biosolids.     

Door-to-door measurement of household waste arisings in selected towns in Malaysia

To establish the per capita household waste arisings, door-to-door measurement of discharged waste was carried out. Survey was done in four 2-week phases over a period of 13 months. A questionnaire survey was also carried out to obtain data on household size and other household characteristics as well as the extent of reduce and recycle activities. The results showed that there is a big variance among households on waste arisings, and that household size is an important socio-economic factor in determining per capita waste generation.