光催化高级氧化与无机陶瓷膜分离技术耦合的研究

近年来,光催化高级氧化技术在深度水处理中已引起广泛关注.悬浮式光催化反应器作为一种高效光催化反应器,传质效果好、光利用率高,但光催化剂尤其是纳米光催化剂从悬浮液中的分离回收成为光催化高级氧化技术应用的难题.引入无机陶瓷膜分离技术来解决这一难题,设计了工艺流程,搭建了耦合装置并优化了工艺参数.该耦合系统在光催化高级氧化降解甲基橙(降解率达到99.1％以上)后能实现光催化剂的高效分离回收再利用,对光催化剂能达到99％以上的截留率.同时,研究更廉价、阻力降更小的膜材料及新型可见光响应光催化剂成为该技术发展的关键.     

天然沸石负载TiO2光催化降解敌敌畏和对硫磷

以钛酸丁酯为原料,以天然沸石作载体负载TiO2制备光催化剂;并采用高压汞灯为光源,用负载型TiO2光催化降解敌敌畏和对硫磷.结果表明,浓度为1.2×10-4mol/L的农药光照2 h左右可完全被光催化氧化为PO3-4.同时,还研究了合成光催化剂的处理温度、溶液的初始pH值、过氧化氢浓度等对负载TiO2光催化降解的影响.     

电助光催化氧化过程中羟基自由基（OH·）的定量分析

电助光催化氧化技术是一种增强型的光催化氧化技术,应用前景广阔.对电助光催化氧化过程中产生的羟基自由基(OH·)进行定量分析对进一步探讨电场辅助作用机理十分重要.以对氯苯甲酸为探针化合物对电助光催化氧化过程中的OH·进行定量分析,发现电助光催化氧化过程中的OH·浓度是普通光催化氧化过程的2倍.对苯甲酰胺进行电助光催化氧化降解试验,求得了苯甲酰胺与羟基自由基的二级反应动力学常数.研究还对电场辅助作用机理进行了分析.     

光催化降解有机污染物的进展

综合国内外资料,探讨了半导体光催化氧化降解不中有机污染物的机理,综述了半导体光催化剂在降解水中有机物方面的研究现状及其进展情况。并对半导体光催化氧化法催化剂本身存在的问题提出了一些看法。     

纳米TiO2光催化氧化去除水中痕量双氯芬酸的研究

以TiCl4为前驱体,采用水解法经不同温度煅烧制备了具有不同理化性能的纳米TiO2光催化剂。利用X射线衍射(XRD)、扫描电子显微镜(SEM)、透射电子显微镜(TEM)、物理吸附仪、紫外—可见光漫反射吸收光谱(UV-Vis DRS)等手段对纳米TiO2的晶相结构、粒径、孔径分布以及禁带宽度等进行了表征。以蒸馏水配制的双氯芬酸溶液为目标物,进行了纳米TiO2光催化氧化去除双氯芬酸的活性测试,研究了纳米TiO2的理化性能与光催化氧化活性之间的关系。结果表明,经400℃煅烧制得的纳米TiO2样品具有最高的光催化氧化活性,其在紫外光照射60min下对双氯芬酸的去除率为98%左右,比单独紫外光照射高出85百分点。纳米TiO2光催化氧化去除双氯芬酸的反应近似一级反应动力学模型,其中经400℃煅烧制得的纳米TiO2光催化氧化去除双氯芬酸的表观反应速率常数为0.054 54min-1,是普通商用TiO2的2倍左右,与德国Degussa P-25TiO2的光催化氧化活性最相近。     

掺硼氧化银光催化剂制备及降解模拟印染废水

采用离子交换共沉淀法制备掺硼氧化银光催化剂并进行相应表征,以甲基橙为降解对象对其光催化氧化性能进行考察,并将其用于可见光下降解多种有机物及模拟印染废水。实验结果表明:掺硼氧化银光催化剂能带带隙为1.29e V,具有很好的光催化氧化-还原能力,可见光下降解甲基橙,光照120 s可实现甲基橙完全降解;重复使用活性保持稳定;对不同有机物均可实现光催化氧化完全降解;模拟印染废水降解实验证实,在p H值5~10范围内,可见光照射下氧化银光催化剂在25 min内可实现混合染料的完全降解。掺硼氧化银是一种具有应用前景的可见光光催化剂。     

Fe/Si/TiO2三元复合光催化剂的性能研究

用溶胶-凝胶法制备了Fe/Si/TiO2三元复合光催化剂,利用X射线衍射(XRD)和紫外-可见漫反射光谱(DRS)对样品进行了分析表征,并以甲基橙为模拟污染物,考察了其光催化活性.结果表明,Fe/Si/TiO2三元复合光催化剂与TiO2相比,光催化活性明显提高;当煅烧温度为900℃、添加Fe的摩尔分数为0.050%时,光催化活性最佳.     

钢渣制光催化剂降解甲基橙的性能研究

以废弃的冶金钢渣为原料制备了光催化剂,对其进行了物性测试,并通过处理甲基橙模拟废水,研究了光催化剂投加量、模拟废水pH值和初始浓度及投加FeCl2作助剂对光催化剂性能的影响.结果表明,实验制备的钢渣光催化剂粉体颗粒分散均匀,紫外-可见光吸收波长较纯TiO2产生了红移,并且具有良好的光催化活性,在最佳处理条件下,光催化氧...     

磷钨酸光催化降解甲基橙溶液的研究

以磷钨酸为光催化剂,在紫外灯照射下,对模拟染料废水甲基橙溶液进行光催化降解,并研究了催化剂加入量、pH值、甲基橙初始浓度和外加氧化剂H2O2对光催化降解效果的影响.结果表明,磷钨酸光催化剂加入量为300 mg/100 mL,pH=2.5时,甲基橙溶液的降解率明显高于其他pH值的降解率;在较低浓度下,甲基橙溶液的光催化降解反应符合一级动力学方程;外加氧化剂H2O2可提高光催化反应速率.     

TiO2光催化剂在污水处理中的应用

在污水处理方面TiO2光催化剂以其独特的氧化活性、光学性能和无机化能力引起了人们极大的关注.对TiO2光催化原理、农药、染料和环境荷尔蒙等有机污染物的分解,提高催化效率的方法以及其实用技术等方面,分别作了综合评述.     

风淬钢渣对高炉渣基微晶玻璃性能的影响

以风淬钢渣和高炉渣为主要原料,采用一次烧结法制备微晶玻璃。结果表明,该方法制备的微晶玻璃主晶相为钙铝黄长石(Ca2Al2SiO7),还有少量的镁黄长石(Ca2MgSi2O7),钢渣最大用量达到50%;随着风淬钢渣含量的增加,样品的最佳烧结温度逐渐增加;烧结温度对样品析晶性能的影响明显大于风淬钢渣含量的影响;样品的抗折强度随风淬钢渣的增加呈现出先增大后减小的趋势;样品的密度随风淬钢渣的增加而逐渐减小;直接用风淬钢渣和高炉渣制备出的微晶玻璃具有良好的抗折强度和耐酸碱性,抗折强度最大可达90 MPa,该方法为综合治理冶金渣污染及其综合利用开辟了新的途径。     

Manganese-cerium oxide (MnOx-CeO2) catalysts supported by titanium-bearing blast furnace slag for selective catalytic reduction of nitric oxide with ammonia at low temperature

A series of manganese-cerium oxide (MnO_x-CeO₂) catalysts supported by Ti-bearing blast furnace slag were prepared by wet impregnation and used for low-temperature selective catalytic reduction (SCR) of NO with NH₃. The slag-based catalyst exhibited high nitrogen oxide removal (deNO_x) activity and wide effective temperature range. Under the condition of NO = 500 ppm, NH₃ = 500 ppm, O₂ = 7–8 vol%, and total flow rate = 1600 mL/min, the Mn-Ce/Slag catalyst exhibited a NO conversion higher than 95% in the range of 180–260 °C. The activity of Mn/Slag catalysts was greatly enhanced with the addition of CeO₂. The results indicated that Ti-bearing blast furnace slag had suitable phase composition as good support of SCR catalyst.

Implications: Ti-bearing blast furnace slag is a kind of industrial waste in China. Much slag was underused and piling up, which could cause many environmental issues, such as enormous waste of titanium and groundwater and soil contamination by heavy metals in leachates. The utilization of slag as the support of SCR catalyst will not only make use of solid waste but also cut down the NO_x emitted from power plant.     

Preparation of Calcium Silicate Absorbent from Iron Blast Furnace Slag

ABSTRACT

Calcium silicate hydrate (CSH) solids were prepared from hydrated lime and iron blast furnace slag in an aqueous agitated slurry at 92 °C. While it was hoped a minimal lime/slag ratio could be used to create near-amorphous CSH, the surface area of the product improved by increasing the lime/slag weight ratio to 2. The addition of gypsum to the lime/slag system dramatically improved the formation of surface area, creating solids with 139 m²/g after 30 hr of reaction when only a minimal amount of lime was present. The SO₂ reactivity of solids prepared with gypsum greatly exceeded that of hydrated lime, achieving greater than 70-80% conversion of the alkalinity after 1 hr of reaction with SO₂. The use of CaCl₂ as an additive to the lime/slag system, in lieu of gypsum, also produced high-surface-area solids, 115 m²/g after 21 hr of reaction. However, the SO₂ reactivity of these sorbents was relatively low given the high surface area. This emphasized that the correlation between surface area and SO₂ reactivity was highly dependent on the solid phase, which was subsequently dependent on slurry composition.     

Effect of Oxidizing and Reducing Conditions on the Reaction of Water with Sulfur Bearing Blast Furnace Slags

The evolution of H₂S and SO₂ from hot blast furnace slags by reaction with H₂O has been found to be dependent upon the presence of O₂ or H₂ in the reaction zone as well as on the temperature. H₂ has been found to produce a small increase in H₂S and a small decrease in SO₂ emission, while O₂ has been found to produce a very great inhibiting effect on H₂S emission and only a small increase in SO₂ emission. The total emission of sulfur bearing gases is much less when H₂O + air is blown at the slag than when H₂O + Ar is blown at the slag, particularly at 1200°C and above. These effects may be useful in attempts to design systems for slag quenching which will produce less pollution.     

Studies on the phosphorus sorption capacity of substrates used in constructed wetland systems

Langmuir sorption isotherm was used to screen various substrates for use in removing phosphorus (P) in constructed wetlands (CW). The nine tested substrates included four sands, two soils, bentonite, and two industrial by-products of furnace slag and fly ash. Results showed that the furnace slag had the highest P sorption capacity (8.89 g Pk g(-1)), followed was the fly ash (8.81 g P kg(-1)), and that of sand II was the lowest. Different kinds of sands also showed varying P sorption capacity (0.13-0.29 g P kg(-1)). P sorption capacity was influenced by both the physico-chemical characteristics of the substrates and the amount of organic matter (OM) added. Lifetime of sand II for P sorption estimated by Langmuir P sorption maximum was up to only 9 months in full-scale systems, while that of furnace slag could be used for up to 22 yr. Furnace slag has great potential as a CW substrate, due to its high P sorption capacity. The expected lifetime of constructed wetlands for P removal is strongly influenced by the choice of adsorbing substrate.     

不同因素对人工湿地基质脱氮除磷效果的影响

在人工配制的污水中投入一定量的基质,不同条件下振荡培养,评价沸石、炉渣和陶瓷滤料3种基质在不同因素影响下对氨氮(NH4+-N)和总磷(TP)的吸附能力。结果表明,不同吸附时间时,沸石对NH4+-N的吸附效果最好,陶瓷滤料对TP的吸附效果最好;进水浓度对沸石吸附NH4+-N的影响较大,其吸附量随进水浓度的增大而增大,进水浓度对炉渣和陶瓷滤料吸附NH4+-N及炉渣吸附TP影响不大;3种基质对NH4+-N和TP的吸附量均是随吸附剂量的增加而降低,要达到较好的去污效果,应根据实验结果考虑基质投入量;pH值对沸石吸附NH4+-N影响显著,pH值6～7范围内吸附效果最好,pH值8～12的碱性条件有利于基质对TP的吸附。     

利用高炉水淬渣制作多孔吸声材料的研究

为了促进高炉炼铁水淬渣的二次利用,研究了以高炉炼铁水淬渣为原料,以硅微粉或水泥为粘结剂,采用压制成型方法制作的多孔吸声材料的吸声性能及力学性能。结果表明:用颗粒状的高炉炼铁水淬渣制作的多孔吸声材料具有良好的吸声性能,其平均吸声系数可以达到0.70以上;材料的抗压强度可以达到3.0 MPa以上。     

颜料红254-TiO_2光催化降解罗丹明B废水

以工业有机颜料C.I.颜料红254(DPP254)为敏化剂,通过溶剂热法对纯TiO2进行改性,得到复合光催化剂DPP254-TiO2。并通过XRD、SEM、UV-Vis DRS和N2吸附-脱附(BET和BJH)等测试手段对DPP254-TiO2进行了表征。以罗丹明B(RhB)为目标降解物,研究了DPP254-TiO2在可见光下对有机污染物的光催化降解性能。同时考察了DPP254含量、反应时间、RhB初始浓度和催化剂浓度等因素对RhB降解速率的影响。结果表明,改性后的催化剂光响应范围由紫外光区拓宽到可见光区。对其光催化反应机理进行了探讨。催化剂重复使用4次,活性没有明显降低,说明催化剂具有很好的稳定性。     

Expanding Blast Furnace Slag Without Air Pollution

Expansion of blast furnace slag causes emissions of hydrogen sulfide, creating an air pollution problem common throughout the steel industry. This paper describes a new process, called pelletizing which eliminates the air pollution problem while at the same time producing a superior slag product.     

CuO/TiO2-H2O2可见光催化亚甲基蓝脱色效果及影响因素研究

以水解法制备的锐钛矿型TiO2为载体,制备了CuO/TiO2型光催化剂.以亚甲基蓝为对象,在可见光照射下研究了H2O3加入量、pH值和催化剂投加量对脱色效果的影响,同时与改性前的TiO2催化剂进行了脱色效果的对比.结果表明亚甲基蓝在碱性条件下能较好脱色,H2O2用量和CuO/TiO2催化剂投加量分别为每1 000 mL反应液各加入10 mL和0.1 g时脱色最好;另外,TiO2催化剂也在碱性条件下能较好脱色,H2O2用量和催化剂投加量分别为每1 000 mL反应液各加入12.5 mL和0.1 g时脱色最好.最优条件下对比实验表明,CuO/TiO2型催化剂在可见光照射下具有很高的催化活性,亚甲基蓝2 h脱色率达到88%,远好于改性前的TiO2和Degussa P25催化剂.