Nationwide monitoring of atmospheric PCDD/Fs and dioxin-like PCBs in South Korea

Polychlorinated dibenzo-p-dioxins and dibenzofurans (PCDD/Fs) and dioxin-like polychlorinated biphenyls (DL-PCBs) were measured in ambient air samples collected from different parts of South Korea in 2008, and the measured levels were used for assessing the spatial and temporal distribution of atmospheric PCDDFs and DL-PCBs in South Korea. The average concentrations of atmospheric PCDD/Fs and DL-PCBs among the 37 sites were 28 fg I-TEQ m⁻³ (ND ∼ 617) and 1 fg WHO-TEQ m⁻³ (ND ∼ 0.016). Elevated atmospheric levels of PCDD/Fs and DL-PCBs observed at residential/industrial sites and in the north-west of Korea, indicated a potential contribution and impacts of anthropogenic sources of PCDD/Fs and DL-PCBs. These levels were similar or lower than those previously reported in other ambient air surveys. Average concentrations of PCDD/Fs showed small seasonal variations (ANOVA analysis, p = 0.144). The highest concentrations of PCDD/Fs were observed during winter, followed by spring, autumn and summer. Atmospheric PCDD/Fs and DL-PCBs in South Korea rapidly decreased during the last 10 years (1998-2008), demonstrating the efficiency of stricter regulations and the application of best available technologies/best environmental practices at emission sources. Comparison of the congener profiles and principal component analysis showed that current atmospheric PCDD/Fs are mostly influenced by industrial sources and PCBs from old commercial PCB uses. Nationwide POPs monitoring will continue and allows an effective evaluation of the implementation of the Stockholm Convention on POPs.     

Estimation and characterization of PCDD/Fs and dioxin-like PCBs from Chinese iron foundries

The iron foundry industry is considered to be a potential source of polychlorinated dibenzo-p-dioxins and dibenzofurans (PCDD/Fs). This study investigated the emission factors and total emission amounts of PCDD/Fs and dioxin-like polychlorinated biphenyls (DL-PCBs) from iron foundries in China. The concentrations and the World Health Organization toxicity equivalents (WHO-TEQs) are presented and the congener profiles are discussed in this paper.In the present work, 26 fly ash samples were collected and tested to quantify the PCDD/Fs and DL-PCBs generated by 14 plants of different scales, and five stack gas samples were collected from two (named as EFG and LFG) of those plants. The emission levels of PCDD/Fs and DL-PCBs indicated that hot-air cupolas had lower emissions than cold-air cupolas. When iron ore lump and sinter were used as raw material, the emission factors were about 250 ng TEQ t⁻¹ of product. However, if the raw material was scrap, the emission factors varied owing to the different contents of organic materials in the raw materials. It was found that the mean WHO-TEQ values of PCDD/Fs and DL-PCBs were 144 and 34.2 pg Nm⁻³ in stack gas and 20.0 and 1.58 pg g⁻¹ in fly ash. In multiple tests, it was estimated that the mean emission factors of PCDD/Fs and DL-PCBs were 365 and 10.9 ng WHO-TEQ t⁻¹ released to residue and 2719 and 555 ng TEQ t⁻¹ released to air. The total emission amounts of PCDD/Fs and DL-PCBs from Chinese iron foundries with cupola furnaces released to residue and air were 16.8 and 146 g WHO-TEQ in 2008, respectively.     

Estimation and characterization of PCDD/Fs, dl-PCBs, PCNs, HxCBz and PeCBz emissions from magnesium metallurgy facilities in China

Magnesium production is considered to be one potential source of unintentional persistent organic pollutants (unintentional POPs). However, studies on the emissions of unintentional POPs from magnesium metallurgy are still lacking. Emissions of unintentional POPs, such as polychlorinated dibenzo-p-dioxins/dibenzofurans (PCDD/Fs), dioxin-like polychlorinated biphenyls (dl-PCBs), polychlorinated naphthalenes (PCNs), hexachlorobenzene (HxCBz) and pentachlorobenzene (PeCBz) are covered under the Stockholm Convention. In this study, these emissions were investigated through a magnesium smelting process. Stack gas and fly ash samples from a typical magnesium plant in China were collected and analyzed to estimate the emissions of unintentional POPs from magnesium metallurgy. Emissions factors of 412 ng TEQ t⁻¹ for PCDD/Fs, 18.6 ng TEQ t⁻¹ for dl-PCBs, 3329 μg t⁻¹ for PCNs, 820 μg t⁻¹ for HxCBz, and 1326 μg t⁻¹ for PeCBz were obtained in 2009. Annual emissions from magnesium metallurgy in China were estimated to be 0.46 g WHO-TEQ for PCDD/Fs and dl-PCBs, 1651 g for PCNs, 403 g for HxCBz and 653 g for PeCBz, respectively.     

PCDD/Fs-induced oxidative damage and antioxidant system responses in tobacco cell suspension cultures

Polychlorinated dibenzo-p-dioxins and polychlorinated dibenzofurans (PCDD/Fs) are ubiquitous contaminants and can be considerably accumulated by natural plants. In order to elucidate the biochemical and physiological responses of plant to PCDD/Fs, tobacco Bright Yellow-2 (BY-2) cells were selected as model plant and treated with time- and concentration-dependent PCDD/Fs. The toxic effect and oxidative stress caused by PCDD/Fs were evident, which could be indicted by the reduction in fresh mass, the increase in malondialdehyde (MDA) content, and the damage of tobacco cell ultrastructure. PCDD/Fs tolerance was correlated with changes in antioxidant system and hormones of tobacco cells. Superoxide dismutase (SOD) and peroxidase (POD) exhibited peak enzyme activities at the PCDD/Fs concentration of 1000 ng WHO₉₈-TEQ g⁻¹ fresh weight. Glutathione reductase (GR) enzyme activity increased monotonically at high level PCDD/Fs, but the activity of catalase (CAT) was only slightly affected at all treatment. Meanwhile, the exposure to PCDD/Fs resulted in the changes of hormones content. With the increase of exposure concentration of PCDD/Fs, the levels of indole-3-acetic acid (IAA) and abscisic acid (ABA) increased, whereas the concentration of jasmonates (JAs) decreased. The above results suggest that tobacco cells had the ability to cope with the oxidative stress induced by low concentration of PCDD/Fs through increasing the activities of antioxidant enzymes and alternating plant hormones levels. However, oxidative stress and toxicity would burst out when plant cells were exposed to the high levels of PCDD/Fs.     

Transport of chlorinated dioxins and furans in soil columns: modeling pentachlorophenol pole-treating oil influence

Column experiments were conducted to validate a screening model predicting the influence of pentachlorophenol (PCP) pole-treating oil on the vertical migration of its impurities, chlorinated dioxins and furans (PCDD/Fs). PCP pole-treating oil (15 mL d⁻¹) and water (20 mL d⁻¹) were added daily to the top of sand and organic soil columns during 35 d. Column soil samples were analyzed to determine concentrations of hydrocarbons and PCDD/Fs at several depths in the columns (0-30 cm) and their evolution in time (7, 14, 21 and 35 d).The model predicted a significant vertical migration of PCDD/Fs due to the presence of oil as a free phase and PCDD/Fs were found in the different column layers at concentrations consistent with model predictions (same order of magnitude). Measured PCDD/Fs concentrations are in total disagreement with literature data and with model prediction in the absence of oil free phase, which implies PCDD/F properties alone cannot be used to predict their fate in the current context: the influence of PCP pole-treating oil must be accounted for to properly explain their migration.     

Contamination and emission factors of PCDD/Fs, unintentional PCBs, HxCBz, PeCBz and polychlorophenols in chloranil in China

The production of chloranil is regarded as a potentially significant source of unintentional POPs. This research aimed to identify the contamination levels of polychlorinated dibenzo-p-dioxins and dibenzofurans (PCDD/Fs), polychlorinated biphenyls (PCBs), hexachlorobenzene (HxCBz), pentachlorobenzene (PeCBz) and polychlorophenols in chloranil samples and identify the formation pathways. The toxicity equivalent (TEQ) values for PCDD/Fs in the chloranil samples ranged from 163 to 1 540 200 pg I-TEQ g⁻¹, while the PCB TEQ values ranged from 1.9 to 3.3 pg WHO-TEQ g⁻¹. High levels of HxCBz, PeCBz and polychlorophenols were also detected in the chloranil samples. The average emission factors were 522.2 mg I-TEQ t⁻¹ (PCDD/Fs), 0.0026 mg WHO-TEQ t⁻¹ (PCBs), 32.6 mg t⁻¹ (HxCBz), and 136.6 mg t⁻¹ (PeCBz). The PCDD/Fs and PCBs are thought to be formed from the polychlorophenols and polychlorobenzenes generated during the chloranil production process. Purification of the chloranil products can reduce the unintentional POPs releases and protect the environment.     

Accurate sampling of PCDD/F in high temperature flue-gas using cooled sampling probes

In a laboratory-scale combustion reactor, flue-gas samples were collected at two temperatures in the post-combustion zone, 700 °C and 400 °C, using two different water-cooled sampling probes. The probes were the cooled probe described in the European Standard method EN-1948:1, referred to as the original probe, and a modified probe that contained a salt/ice mixture to assist the cooling, referred to as the sub-zero probe. To determine the efficiency of the cooling probes, internal temperature measurements were recorded at 5 cm intervals inside the probes. Flue-gas samples were analyzed for polychlorinated dibenzo-p-dioxin and dibenzofurans (PCDD/Fs). Samples collected at 700 °C using the original cooling probe showed higher concentrations of PCDD/Fs compared to samples collected using the sub-zero probe. No significant differences were observed between samples collected at 400 °C. The results indicated that artifact formation of PCDD/Fs readily occurs during flue-gas sampling at high temperatures if the cooling within the probe is insufficient, as found for the original probe at 700 °C. It was also shown that this problem could be alleviated by using probes with an enhanced cooling capacity, such as the sub-zero probe.Although this may not affect samples collected for regulatory purposes in exit gases, it is of great importance for research conducted in the high-temperature region of the post-combustion zone.     

Thermal removal of PCDD/Fs from medical waste incineration fly ash--effect of temperature and nitrogen flow rate

The fly ash used in this study was collected from a bag filter in a medical waste rotary kiln incineration system, using lime and activated carbon injection followed by their collection as mixed fly ash. Experiments were conducted on fly ash in a quartz tube, heated in a laboratory-scale horizontal tube furnace, in order to study the effect of temperature and nitrogen flow rate on the removal of PCDD/Fs. Results indicated that in this study PCDD/Fs in the fly ash mostly were removed and desorbed very little into the flue gas under thermal treatment especially when the heating temperature was higher than 350 °C, and dechlorination and destruction reactions took important part in the removal of PCDD/Fs. However, in terms of flow rate, when flow rate was higher than 4 cm s⁻¹, destruction efficiency of PCDD/Fs decreased dramatically and the main contributors were P₅CDF, H₆CDF and H₇CDF desorbed to flue gas, the PCDD/Fs in the fly ash decreased with enhanced flow rate.     

A proposal for a diet-based local PCDD/F deposition limit

This study proposes a method to estimate the maximal tolerable value for the atmospheric deposition of dioxins (PCDD/Fs) to soil. The case study for the application of this methodology is an Alpine valley where a steel production plant is present. In order to estimate the limit value for the PCDD/F deposition, consolidated food chain models were applied, but were adapted to be run backwards with respect to their original formulation, by starting from the diet of people living in the region and from the PCDD/F Tolerable Daily Intake value proposed by the World Health Organization. For this case study, the estimated limit value was 2.30 pg WHO-TEQ m⁻² d⁻¹ when only local diary products were taken into account and 1.91 pg WHO-TEQ m⁻² d⁻¹ when also the role of local cereals and vegetables was considered. The average PCDD/F deposition measured in the same region during a monitoring campaign was lower than the above limit values (1.40 pg WHO-TEQ m⁻² d⁻¹). Indications on how to consider the contribution of meat and fish are provided too. The approach proposed in this paper represents a useful tool to assess the acceptable overall deposition for a specific region.     

Analysis of PCDD/Fs and dioxin-like PCBs in atmospheric deposition samples from the Flemish measurement network: correlation between the CALUX bioassay and GC-HRMS

Since the CALUX (Chemically Activated LUciferase gene eXpression) bioassay is a fast, sensitive and inexpensive tool for the analysis of a high number of samples, the use of this technique in routine analysis of atmospheric deposition samples may be a valuable alternative for GC-HRMS. In this study, a validated CALUX method was used for the analysis of PCDD/Fs and dioxin-like PCBs in more than 90 atmospheric deposition samples for different locations in Flanders. The samples were taken in residential and agricultural areas, where a threshold limit of 21 pg WHO-TEQ m⁻² d⁻¹ for the sum of PCDD/Fs and dioxin-like PCBs was set, and in industrial zones and natural reserves, where no official threshold limit is available. The results from the Flemish measurement program showed correlation between CALUX and GC-HRMS for all the samples, originating from the different areas (R² of 0.81, 0.53 and 0.64 for dl-PCBs, PCDD/Fs and sum of both fractions, respectively). Median CALUX/GC-HRMS ratios of 2.0, 0.9 and 1.3 were reported for the PCDD/Fs, dioxin-like PCBs and the sum of both fractions, respectively. The results show that the CALUX bioassay is a valuable alternative tool for the classic GC-HRMS analysis of atmospheric deposition samples in the Flemish measurement network.     

PCDDs, PCDFs, dioxin-like PCBs and indicator PCBs in soil from five selected areas in Slovakia

There is a lack of information regarding persistent organic pollutants (POPs) in soil from Slovakia. This paper reports the concentrations of 17 polychlorinated dibenzo-p-dioxins and dibenzofurans (PCDD/Fs), 12 dioxin-like polychlorinated biphenyls (dl-PCBs) and 6 indicator PCBs associated with 32 soil samples collected in 2007 from areas in the vicinity up to several kilometres from four selected industrial PCDD/F sources in Slovakia and one background area.The results show that the total WHO₁₉₉₈-PCDD/F/dl-PCB-TEQ concentrations varied from 0.34 to 18.05 pg g⁻¹ dry weight (dw) and the average total TEQ concentrations in samples collected at the Šala, Košice, Krompachy and Dubová areas were 3.18, 2.64, 7.80, and 3.19 pg g⁻¹ dw respectively. The average of the total WHO₁₉₉₈-TEQ values in three soil samples representing the background Starina area was 0.66 pg g⁻¹ dw. The predominant contaminants among 2,3,7,8-substituted PCDD/Fs, dl-PCB, and indicator PCBs was OCDD, PCB 118, and PCB 153 respectively. The major contributors to the TEQ were 2,3,4,7,8-PeCDF, PCB 126, 1,2,3,7,8-PeCDD, PCB 156 and 1,2,3,4,7,8-HxCDF + 1,2,3,4,7,9-HxCDF in descending order.     

Analysis of polychlorinated dibenzo-p-dioxins and furans in various aqueous samples in Taiwan

Twenty-one fresh water samples were taken from reservoirs, wells and drinking water treatment plants in Taiwan for measurement of polychlorinated dibenzo-p-dioxins and dibenzofurans (PCDD/F) concentrations. Due to low concentration of PCDD/Fs, water samples (400-1000 L) were collected by using the on-site large volume pre-concentration system and analyzed by high resolution gas chromatography (HRGC)/high resolution mass spectrometer (HRMS). Different characteristics of dioxin profiles in surface water and groundwater are observed. The PCDD/F concentrations in fresh water samples varied from 0.001 to 0.265 pg WHO₉₈-TEQ/L which are lower than the standard (12 pg WHO₉₈-TEQ/L) set by the Taiwan Environmental Protection Administration (TEPA) for drinking water. Only a small fraction (<5%) of the total PCDD/F concentration in fresh water samples was water-soluble. As a result of their hydrophobicity, PCDD/Fs are effectively removed along with suspended solid via the water treatment process (average 98% removal efficiency).     

Sources of PCDD/Fs, non-ortho PCBs and PAHs in sediments of high and low impacted transboundary rivers (Belgium-France)

PAHs, PCDD/Fs and non-ortho PCBs have been assessed in Yser and Upper-Scheldt river sediments. Higher contamination levels were observed in the Upper-Scheldt sediments: maximum concentrations for the 16 US-EPA PAHs, PCDD/Fs and non-ortho PCBs respectively amount to 8.9 mg kg⁻¹, 12 ng TEQ kg⁻¹ and 5.1 ng TEQ kg⁻¹. Diagnostic PAH ratios in sediments and atmospheric samples suggest that the PAH compounds are from pyrolytic origin, more specifically combustion processes. The huge consumption of coal in cokes-ovens and smelters and its use for house-heating in Northern France, although decreasing during the last decades, are in support of that suggestion. PCDD/F fingerprints in sediments and deposition material indicate that OCDD is the dominant congener. In addition use of pentachlorophenol (PCP) in the past led to a minor contribution of PCDD/Fs in our sediment samples. Non-ortho PCBs form a substantial fraction of the total TEQ concentrations observed in the sediments. Since the 1980s and 1990s a substantial reduction of the PCDD/F sediment concentrations is observed, but this is not the case for the PAHs.     

Polychlorinated dibenzo-p-dioxins,dibenzofurans, biphenyls,paraffins and polybrominated diphenyl ethers in marine fish species from Ebro River Delta (Spain)

The results of a surveillance programme on the determination of polychlorinated dibenzo-p-dioxins (PCDDs), polychlorinated dibenzofurans (PCDFs), polychlorinated biphenyls (PCBs), polybrominated diphenyl ethers (PBDEs) and short chain chlorinated paraffins (SCCPs) in marine fish and shellfish species which are fished, commercialised and consumed in the Ebro River Delta area (NE, Spain) are presented. The study included the analysis of five marine fish species (sardine, gilthead sea bream, conger, eel and flounder) and three shellfish species (murex, carpet shell and mussel) collected in 2012 in five fishing harbours near to this area. WHO-TEQ concentrations for PCDD/Fs and dioxin like PCBs (dl-PCBs) ranged from 0.03 to 0.31 pg WHO-TEQ_2005PCDD/F g⁻¹ wet weight (ww) and from 0.02 to 3.15 pg WHO-TEQ_2005PCB g⁻¹ ww, respectively. All levels were below the maximum concentrations established by the EU Regulation. The PCBs and PCDD/Fs accumulation pattern found in the samples analysed showed a distribution typically reported for marine samples. For marker PCBs and PBDEs, concentration levels ranging from 929 to 57 494 pg g⁻¹ ww and from 36.2 to 827 pg g⁻¹ ww were obtained, respectively, meanwhile for SCCPs levels were between 3.1 and 141 ng g⁻¹ ww. Finally, the trends in the levels of PCDD/F and dl-PCBs found from 2006 to 2012 in fish and shellfish species were studied. A slight decrease of PCDD/F and dl-PCB concentrations was found since 2006.     

Polychlorinated dibenzo-p-dioxin and dibenzofuran in urban air of an Andean city

Particle-bound polychlorinated dibenzo-p-dioxins and polychlorinated dibenzofurans (PCDD/Fs) in ambient air were monitored together with particulate matter less than 10 μm (PM₁₀) at three sampling sites of the Andean city of Manizales, Colombia; during September 2009 and July 2010. PCDD/Fs ambient air emissions ranged from 1 fg WHO-TEQ m⁻³ to 52 fg WHO-TEQ m⁻³ in particulate fraction. The PM₁₀ concentrations ranged from 23 μg m⁻³ to 54 μg m⁻³. Concentrations of PM₁₀ and PCDD/Fs in ambient air observed for Manizales - a medium sized city with a population of 380 000 - were comparable to concentrations in larger cities. The highest concentrations of PCDD/Fs and PM₁₀ found in this study were determined at the central zone of the city, characterized by public transportation density, where diesel as principal fuel is used. In addition, hypothetical gas fractions of PCDD/Fs were calculated from theoretical K_p data. Congener profiles of PCDD/Fs exhibited ratios associated with different combustion sources at the different sampling locations, ranging from steel recycling to gasoline and diesel engines. Taking into account particle and gas hypothetical fraction of PCDD/Fs, Manizales exhibited values of PCDD/Fs equivalent to rural and urban-industrial sites in the southeast and center of the city respectively. Poor correlation of PCDDs with PM₁₀ (r = −0.55 and r = 0.52) suggests ambient air PCDDs were derived from various combustion sources. Stronger correlation was observed of PCDFs with PM₁₀. Poor correlation between precipitation and reduced PM₁₀ concentration in ambient air (r = −0.45) suggested low PM₁₀ removal by rainfall.     

Determination of dioxin concentrations in fish and seafood samples using a highly sensitive reporter cell line, DR-EcoScreen cells

There is a strong need for the development of relatively rapid and low-cost bioassays for the determination of polychlorinated dibenzo-p-dioxins and dibenzofurans (PCDD/Fs), and dioxin-like polychlorinated biphenyls (dl-PCBs) in environmental and food samples. In this study, we applied a reporter gene assay using DR-EcoScreen cells (DR-cell assay), which is highly sensitive to dioxins, to the determination of PCDD/Fs and dl-PCBs in fish and seafood samples. The PCDD/Fs and dl-PCBs were extracted from homogenated samples (10 g) of 30 fish and shellfish, purified by clean-up procedure using a multilayered silica gel column and an alumina column, and applied to DR-cell assay. Interestingly, the bioanalytical equivalent (BEQ) values obtained from the DR-cell assay [<0.1 ∼ 5.4 pg BEQ g⁻¹ wet weight (ww)] were closely correlated with the toxicity equivalent (TEQ) values from conventional high-resolution gas chromatography/high-resolution mass spectrometry (HRGC-HRMS) analysis (r² = 0.912), and the slope of regression line was 0.913. Therefore, we multiplied the BEQ values from the DR-cell assay by a conversion coefficient (1.095, the reciprocal of 0.913) to approximate the TEQ values from the HRGC-HRMS analysis. Furthermore, we used this DR-cell assay to perform a prescreening test of PCDD/Fs and dl-PCBs in 16 fish and seafood samples purchased from a supermarket, revealing that a sample from the fatty flesh of a bluefin tuna exceeded 8 pg TEQ g⁻¹ ww (the European Union-tolerance limit). Taken together, these results suggest that the DR-cell assay might be applicable as a rapid and low-cost prescreening method to determine dioxin levels in fish and seafood samples.     

Reduction of dioxin emission by a multi-layer reactor with bead-shaped activated carbon in simulated gas stream and real flue gas of a sinter plant

A laboratory-scale multi-layer system was developed for the adsorption of PCDD/Fs from gas streams at various operating conditions, including gas flow rate, operating temperature and water vapor content. Excellent PCDD/F removal efficiency (>99.99%) was achieved with the multi-layer design with bead-shaped activated carbons (BACs). The PCDD/F removal efficiency achieved with the first layer adsorption bed decreased as the gas flow rate was increased due to the decrease of the gas retention time. The PCDD/F concentrations measured at the outlet of the third layer adsorption bed were all lower than 0.1 ng I-TEQ Nm⁻³. The PCDD/Fs desorbed from BAC were mainly lowly chlorinated congeners and the PCDD/F outlet concentrations increased as the operating temperature was increased. In addition, the results of pilot-scale experiment (real flue gases of an iron ore sintering plant) indicated that as the gas flow rate was controlled at 15 slpm, the removal efficiencies of PCDD/F congeners achieved with the multi-layer reactor with BAC were better than that in higher gas flow rate condition (20 slpm). Overall, the lab-scale and pilot-scale experiments indicated that PCDD/F removal achieved by multi-layer reactor with BAC strongly depended on the flow rate of the gas stream to be treated.     

Formation of dioxins during exposure of pesticide formulations to sunlight

Chlorinated pesticides can contain impurities of dibenzo-p-dioxins and dibenzofurans (PCDD/Fs), and their precursors, as a result of various manufacturing processes and conditions. As precursor formation of PCDD/Fs can also be mediated by ultraviolet light (UV), this study investigated whether PCDD/Fs are formed when currently used pesticides are exposed to natural sunlight. Formulations containing pentachloronitrobenzene (PCNB; n = 2) and 2,4-dichlorophenoxyacetic acid (2,4-D; n = 1) were exposed to sunlight in quartz tubes, and the concentration of 93 PCDD/F congeners were monitored over time. Considerable formation of PCDD/Fs was observed in both PCNB formulations (by up to 5600%, to a maximum concentration of 57 000 μg ∑PCDD/F kg⁻¹) as well as the 2,4-D formulation (by 3000%, to 140 μg ∑PCDD/F kg⁻¹). TEQ also increased by up to 980%, to a maximum concentration of 28 μg kg⁻¹ in PCNB, but did not change in the 2,4-D formulation. Assuming similar yields as observed in the present study as a worst case scenario the use of PCNB in Australia may result in the formation of 155 g TEQ annum⁻¹, contributed primarily by OCDD formation. This warrants detailed evaluations on the contemporary release of PCDD/Fs to the environment after the use of pesticides. Changes in congener profiles (including the ratio of PCDDs to PCDFs (DF ratio)) suggest that pesticide sources of PCDD/Fs after sunlight exposure may not be recognized based on matching source fingerprints established from manufacturing impurities. These changes also provide preliminary insights into the possible formation routes and types of precursors involved.     

Evaluation of atmospheric sources of PCDD/Fs, PCBs and PBDEs around a steel industrial complex in northeast China using passive air samplers

The concern about emissions of polychlorinated dibenzo-p-dioxins and dibenzofurans (PCDD/Fs) polychlorinated biphenyls (PCBs), and polybrominated diphenyl ethers (PBDEs) from steel industrial parks has increased in the past decades. In this study, polyurethane foam (PUF)-disk based passive air samples were collected in and around a big steel industrial park of Anshan, Northeast China from June 2008 to March 2009. The levels, seasonal variations and potential sources of PCDD/Fs, PCBs and PBDEs in the atmosphere around the steel industrial complex were investigated, and potential contribution of these three groups of persistent organic pollutants (POPs) from iron and steel production was also assessed. The air concentrations of ∑₁₇PCDD/Fs (summer: 0.02-2.77 pg m⁻³; winter: 0.20-9.79 pg m⁻³), ∑₁₉PCBs (summer: 23.5-155.8 pg m⁻³; winter: 14.6-81.3 pg m⁻³) and ∑₁₃PBDEs (summer: 2.91-10.7 pg m⁻³; winter: 1.10-3.89 pg m⁻³) in this targeted industrial park were relatively low in comparison to other studies, which implied that the industrial activities of iron and steel had not resulted in serious contamination to the ambient air in this area. On the whole, the air concentrations of PCDD/Fs in winter were higher than those of summer, whereas the concentrations of PCBs and PBDEs showed opposite trends. The result from principal component analysis indicated that coal combustion might be the main contributor of PCDD/F sources in this area.     

Congener profile, occurrence and estimated dietary intake of dioxins and dioxin-like PCBs in foods marketed in the Region of Valencia (Spain)

During 2006-2008, a monitoring program was conducted on 29 target compounds, including PCDD/Fs and dl-PCBs, comprising 150 randomly collected individual food samples marketed in the Region of Valencia, Spain, grouped into 8 categories (vegetables, cereals, fats and oils, eggs, milk and dairy products, fish products, meat and meat products and fish oil). For PCDD/Fs, the highest frequency of detection corresponds to 1,2,3,4,6,7,8-HpCDD, OCDD, 2,3,4,7,8-PeCDF; and PCBs 118, 105 and 156 were the more frequent dl-PCBs. The food groups presenting higher contamination, expressed as toxic equivalents (WHO-TEQs), were fish oil (6.38 pg WHO-TEQ g⁻¹ fat), fish (1.21 pg WHO-TEQ g⁻¹ w.w.) and milk and dairy products (0.90 pg WHO-TEQ g⁻¹ fat). Of all analysed samples, only two fish oils presented levels higher than the EU limits for total WHO-TEQ. The average PCDD/Fs and dl-PCBs intakes were estimated as 2.86 pg WHO-TEQ kg⁻¹ b.w. d⁻¹ and 4.58 pg WHO-TEQ kg⁻¹ b.w. d⁻¹, for adults and children, respectively, using the deterministic method for chronic exposure. The main contributors to total intake for adults were fish (59%), milk and dairy products (19%), and fat and oils (9%). The average daily intake for adults (2.86 pg WHO-TEQ kg⁻¹ b.w. d⁻¹) is within range of TDI recommended by the WHO (1-4 pg WHO-TEQ kg⁻¹ b.w. d⁻¹), and slightly above the TWI and PTMI adopted by SCF and JECFA respectively.