Open burning of household waste: Effect of experimental condition on combustion quality and emission of PCDD, PCDF and PCB

Open burning for waste disposal is, in many countries, the dominant source of polychlorinated dibenzodioxins, dibenzofurans and biphenyls (PCDD/PCDF/PCB) release to the environment. To generate emission factors for open burning, experimental pile burns of about 100 kg of household waste were conducted with emissions sampling. From these experiments and others conducted by the same authors it is found that less compaction of waste or active mixing during the fire - “stirring” - promotes better combustion (as evidenced by lower CO/CO₂ ratio) and reduces emissions of PCDD/PCDF/PCB; an intuitive but previously undemonstrated result. These experiments also support previous results suggesting PCDD/PCDF/PCB generation in open burning - while still highly variable - tends to be greater in the later (smoldering) phases of burning when the CO/CO₂ ratio increases.     

Quality control for sampling of PCDD/PCDF emissions from open combustion sources

Both long duration (>6 h) and high temperature (up to 139 °C) sampling efforts were conducted using ambient air sampling methods to determine if either high volume throughput or higher than ambient air sampling temperatures resulted in loss of target polychlorinated dibenzodioxins/dibenzofurans (PCDDs/PCDFs) from a polyurethane foam (PUF) sorbent. Emissions from open burning of simulated military forward operating base waste were sampled using EPA Method TO-9A for 185 min duration using a filter/PUF/PUF in series combination. After a 54 m³ sample was collected, the sampler was removed from the combustion source and the second PUF was replaced with a fresh, clean PUF. An additional 6 h of ambient air sampling (171 m³) was conducted and the second PUF was analyzed to determine if the PCDD/PCDF transferred from the filter and the first PUF. Less than 4.4% of the initial PCDD/PCDF was lost to the second PUF. To assess the potential for blow off of PCDD/PCDF analytes during open air sampling, the mobility of spiked mono- to hepta-PCDD/PCDF standards across a PUF sorbent was evaluated from ambient air temperatures to 145 °C with total volumes between 600 L and 2400 L. Lower molecular weight compounds and higher flow amounts increased release of the spiked standards consistent with vapor pressure values. At 600 L total sampled volume, the release temperature for 1% of the tetra-CDD (the lowest chlorinated homologue with a toxic compound) was 87 °C; increasing the volume fourfold reduced this temperature to 73 °C.     

Influence of pesticides contamination on the emission of PCDD/PCDF to the land from open burning of corn straws

Open burning of crop residues has been identified as an important emission source of PCDD/PCDF to the environment. This paper presents the first known data on the emission of PCDD/PCDF to the land considering the influence of pesticides applied in crops planting. Emission factor for PCDD/PCDF to the land from open burning of corn straw with pesticides contamination ranged from 0.07 to 0.57 ng WHO₂₀₀₅-TEQ/kg straw burned with a mean value of 0.24 ng WHO₂₀₀₅-TEQ/kg straw burned and median value of 0.20 ng WHO₂₀₀₅-TEQ/kg straw burned, respectively. The concentration was 35 to 270 times higher than that without additional pesticide contaminated. Initial observation was that emission factor for PCDD/PCDF from open burning of crop residues was overestimated in the former UNEP Dioxin Toolkit. Pesticides contamination should be considered in some hotpots where special and over dosed pesticides has been sprayed especially in developing countries.     

Trends,temporal and spatial characteristics,and uncertainties in biomass burning emissions in the Pearl River Delta,China

Multi-year inventories of biomass burning emissions were established in the Pearl River Delta (PRD) region for the period 2003–2007 based on the collected activity data and emission factors. The results indicated that emissions of sulfur dioxide (SO₂), nitrogen oxide (NO_x), ammonia (NH₃), methane (CH₄), organic carbon (OC), non-methane volatile organic compounds (NMVOC), carbon monoxide (CO), and fine particulate matter (PM_2.5) presented clear declining trends. Domestic biofuel burning was the major contributor, accounting for more than 60% of the total emissions. The preliminary temporal profiles were established with MODIS fire count information, showing that higher emissions were observed in winter (from November to March) than other seasons. The emissions were spatially allocated into grid cells with a resolution of 3 km × 3  km, using GIS-based land use data as spatial surrogates. Large amount of emissions were observed mostly in the less developed areas in the PRD region. The uncertainties in biomass burning emission estimates were quantified using Monte Carlo simulation; the results showed that there were higher uncertainties in organic carbon (OC) and elemental carbon (EC) emission estimates, ranging from ?71% to 133% and ?70% to 128%, and relatively lower uncertainties in SO₂, NO_x and CO emission estimates. The key uncertainty sources of the developed inventory included emission factors and parameters used for estimating biomass burning amounts.     

PCDDs/PCDFs in ambient air (<1 fg m(-3)) - the CTDEP long term sampling (30 d) method

The Connecticut Department of Environmental Protection (CTDEP) commenced monitoring for PCDDs/PCDFs (polychlorinated dibenzodioxins and polychlorinated dibenzofurans) in ambient air in 1987 and adopted the long term (30 d) sampling approach in 1993. The CTDEP method represents the first use of isotopically labeled PCDDs/PCDFs as field surrogates to monitor the behavior of native PCDDs/PCDFs present in actual ambient air samples. This feature first introduced in 1987 was later adopted by US EPA in revisions to sampling methods for PCDDs/PCDFs in ambient air (EPA Method TO9A) as well as development of EPA Reference Method 23 for measurement of PCDDs/PCFDs in stationary source emissions. Results are provided here for a total of twenty-three (23) samples (reported as pairs) representing twelve (12) 30 d sampling events conducted at a site located in metropolitan Hartford CT. Samples were collected in winter months during calendar years 2002-2008. PCDDs/PCDFs concentration data (pg m⁻³) are reported as both congener sums (Cl₄-Cl₈) and 2378-substitued congeners. Total PCDDs/PCDFs concentrations for these twelve (12) sampling events ranged from 0.68 pg m⁻³ (2003) to 4.18 pg m⁻³ (2004) with a mean concentration of 2.04 pg m⁻³.Method performance was monitored through use of collocated samples, in field isotopically labeled compounds, isotopically labeled laboratory applied internal standards and field blank samples. Method performance consistently exceeded goals established in USEPA Method TO9A for these same parameters. Average recoveries of in field labeled PCDDs/PCDFs ranged from 97.5% to 104.2%. Average (mean) recoveries for each of the ten (10) isotopically labeled internal standards ranged from 77.0% (¹³C-OCDF) to 95.5% (¹³C-2,3,7,8-TCDF). Method precision defined as % RPD data for collocated sampler pairs ranged from 8% to 14% for PCDDs and from 5% to 12% for PCDFs. The mean RPD for all PCDDs/PCDFs combined is 9.6%. Field monitoring results demonstrate method sensitivity for all PCDDs/PCDFs congeners and 2378-substituted congeners to be well below concentrations typically found for these compounds in ambient air (all reported data represent measured concentrations). Quantities (pg) found in field blanks represent the major determinant to achieving further enhancements in method sensitivity for selected congeners (OCDD < 42 fg m⁻³; 1,2,3,4,6,7,8-HpCDD < 5.7 fg m⁻³; and 1,2,3,4,6,7,8-HpCDF < 2.1 fg m⁻³). The CTDEP method represents a highly sensitive and reliable technique for monitoring of PCDDs/PCDFs congeners and other persistent organic pollutants (POPs) at ultra trace levels in ambient air (fg m⁻³).     

Impact of anthropogenic emissions and open biomass burning on regional carbonaceous aerosols in South China

Carbonaceous aerosols were studied at three background sites in south and southwest China. Hok Tsui in Hong Kong had the highest concentrations of carbonaceous aerosols (OC = 8.7 ± 4.5 μg/m³, EC = 2.5 ± 1.9 μg/m³) among the three sites, and Jianfeng Mountains in Hainan Island (OC = 5.8 ± 2.6 μg/m³, EC = 0.8 ± 0.4 μg/m³) and Tengchong mountain over the east edge of the Tibetan Plateau (OC = 4.8 ± 4.0 μg/m³, EC = 0.5 ± 0.4 μg/m³) showed similar concentration levels. Distinct seasonal patterns with higher concentrations during the winter, and lower concentrations during the summertime were observed, which may be caused by the changes of the regional emissions, and monsoon effects. The industrial and vehicular emissions in East, Southeast and South China, and the regional open biomass burning in the Indo-Myanmar region of Asia were probably the two major potential sources for carbonaceous matters in this region.     

Estimation of Organic Compound Emissions from Waste Lagoons

Abstract

With the recent focus on fine particle matter (PM_2.5),new, self-consistent data are needed to characterize emissions from combustion sources. Such data are necessary for health assessment and air quality modeling. To address this need, emissions data for gas-fired combustors are presented here, using dilution sampling as the reference.The dilution method allows for collection of emitted particles under conditions simulating cooling and dilution during entry from the stack into the air. The sampling and analysis of the collected particles in the presence of precursor gases, SO₂, nitrogen oxide, volatile organic compound, and NH₃ is discussed; the results include data from eight gas fired units, including a dual-fuel institutional boiler and a diesel engine powered electricity generator. These data are compared with results in the literature for heavy-duty diesel vehicles and stationary sources using coal or wood as fuels. The results show that the gas-fired combustors have very low PM_2.5 mass emission rates in the range of ～10_-4 lb/million Btu (MMBTU) compared with the diesel backup generator with particle filter, with ～5 × 10_-3 lb/MMBTU. Even higher mass emission rates are found in coal-fired systems, with rates of ～0.07 lb/MMBTU for a bag-filter-controlled pilot unit burning eastern bituminous coal. The characterization of PM_2.5 chemical composition from the gas-fired units indicates that much of the measured primary particle mass in PM_2.5 samples is organic or elemental carbon and, to a much less extent, sulfate. Metal emissions are quite low compared with the diesel engines and the coal- or woodfueled combustors. The metals found in the gas-fired combustor particles are low in concentration, similar in concentration to ambient particles. The interpretation of the particulate carbon emissions is complicated by the fact that an approximately equal amount of particulate carbon (mainly organic carbon) is found on the particle collector and a backup filter. It is likely that measurement artifacts, mostly adsorption of volatile organic compounds on quartz filters, are positively biasing “true” particulate carbon emission results.     

On the origin of water-soluble organic tracer compounds in fine aerosols in two cities: the case of Los Angeles and Barcelona

Water-soluble organic compounds (WSOCs), represented by anhydro-saccharides, dicarboxylic acids, and polyols, were analyzed by gas chromatography interfaced to mass spectrometry in extracts from 103 PM₁ and 22 PM_2.5 filter samples collected in an urban background and road site in Barcelona (Spain) and an urban background site in Los Angeles (USA), respectively, during 1-month intensive sampling campaigns in 2010. Both locations have similar Mediterranean climates, with relatively high solar radiation and frequent anti-cyclonic conditions, and are influenced by a complex mixture of emission sources. Multivariate curve resolution-alternating least squares analyses were applied on the database in order to resolve differences and similarities in WSOC compositions in the studied sites. Five consistent clusters for the analyzed compounds were obtained, representing primary regional biomass burning organic carbon, three secondary organic components (aged SOC, isoprene SOC, and α-pinene SOC), and a less clear component, called urban oxygenated organic carbon. This last component is probably influenced by in situ urban activities, such as food cooking and traffic emissions and oxidation processes.     

Formation of artefacts while sampling emissions of PCDD/PCDF from open burning of biomass

Emission factors for PCDD/PCDF determined from open combustion are used to estimate national emission budgets; therefore, it is important to have confidence in their accuracy. It has been suspected that artefacts may form due to the presence of hot metal surfaces of sampling equipment, thus skewing emission factors. In this study, emissions of PCDD/PCDF from open burning of forest biomass over a brick hearth were sampled. Five experiments were carried out using a portable sampler. Experiments were designed where the key variable, sample hood and inlet temperatures were manipulated. Other variables such as fuel origin, type and density were consistent. The measured concentration of PCDD/PCDF in the smoke samples ranged from 0.01 μg TEQ (t fuel)⁻¹ at the lowest maximum hood temperature (185 °C) to 15 μg TEQ (t fuel)⁻¹ at the highest maximum hood temperature (598 °C). when hood inlet temperatures exceeded 400 °C emission factors were significantly elevated and this is attributed to the formation of artefacts that can cause the over estimation of emission factors. The increase in hood temperature also resulted in a change in the PCDD/PCDF congener and homologue profile of the emissions. For example at the lowest temperature (Fire 1) the PCDD/PCDF ratio measured was 50:1, whereas at the highest temperature (Fire 5) this ratio was about 0.53:1. When the sampler hood and inlet temperatures were kept in the normal operating range of <200 °C, emission factors were comparable to those observed in many previous studies in Australia with emissions dominated by PCDD.     

Historical estimation of carbonaceous aerosol emissions from biomass open burning in China for the period 1990-2005

Multi-year inventories of carbonaceous aerosol emissions from biomass open burning at a high spatial resolution of 0.5° × 0.5° have been constructed in China using GIS methodology for the period 1990-2005. Black carbon (BC) emissions have increased by 383.03% at an annual average rate of 25.54% from 14.05 Gg in 1990 to 67.87 Gg in 2005; while organic carbon (OC) emissions have increased by 365.43% from 57.37 Gg in 1990 to 267.00 Gg in 2005. Through the estimation period, OC/BC ratio for biomass burning was averagely 4.09, suggesting that it was not the preferred control source from a climatic perspective. Spatial distribution of BC and OC emissions were similar, mainly concentrated in three northeastern provinces, central provinces of Shandong, Jiangsu, Anhui and Henan, and southern provinces of Guangxi, Guangdong, Hunan and Sichuan basin, covering 24.89% of China’s territory, but were responsible for 63.38% and 67.55% of national BC and OC emissions, respectively.     

Determination and potential importance of diterpene (kaur-16-ene) emitted from dominant coniferous trees in Japan

Reactive volatile organic compounds (VOCs) are known to affect atmospheric chemistry. Biogenic VOCs (BVOCs) have a significant impact on regional air quality due to their large emission rates and high reactivities. Diterpenes (most particularly, kaur-16-ene) were detected in all of the 205 enclosure air samples collected over multiple seasons at two different sites from Cryptomeria japonica and Chamaecyparis obtusa trees, the dominant coniferous trees in Japan,. The emission rate of kaur-16-ene, was determined to be from 0.01 to 7.1 μg dwg⁻¹ h⁻¹ (average: 0.61 μg dwg⁻¹ h⁻¹) employing branch enclosure measurements using adsorbent sampling followed by solid phase-liquid extraction techniques. The emission rate was comparable to that of monoterpenes, which is known major BVOC emissions, collected from the same branches. In addition, total emission of kaur-16-ene at 30 °C was estimated to exceed that of total anthropogenic VOC emissions.     

The effects of dissolved organic matter and pH on sampling rates for polar organic chemical integrative samplers (POCIS)

The effect of solution pH and levels of dissolved organic matter (DOM) on the sampling rates for model pharmaceuticals and personal care products (PPCPs) and endocrine disrupting substance (EDS) by polar organic chemical integrative samplers (POCIS) was investigated in laboratory experiments. A commercially available POCIS configuration containing neutral Oasis HLB (hydrophilic-lipophilic balance) resin (i.e. pharmaceutical POCIS) and two POCIS configurations prepared in-house containing MAX and MCX anion and cation exchange resins, respectively were tested for uptake of 21 model PPCPs and EDS, including acidic, phenolic, basic and neutral compounds. Laboratory experiments were conducted with dechlorinated tap water over a pH range of 3, 7 and 9. The effects of DOM were studied using natural water from an oligotrophic lake in Ontario, Canada (i.e. Plastic Lake) spiked with different amounts of DOM (the concentration of dissolved organic carbon ranged from 3 to 5 mg L⁻¹ in uptake experiments). In experiments with the commercial (HLB) POCIS, the MCX-POCIS and the MAX-POCIS, the sampling rates generally increased with pH for basic compounds and declined with pH for acidic compounds. However, the sampling rates were relatively constant across the pH range for phenols with high pKa values (i.e. bisphenol A, estrone, estradiol, triclosan) and for the neutral pharmaceutical, carbamazepine. Thus, uptake was greatest when the amount of the neutral species in solution was maximized relative to the ionized species. Although the solution pH affected the uptake of some model ionic compounds, the effect was by less than a factor of 3. There was no significant effect of DOM on sampling rates from Plastic Lake. However, uptake rates in different aqueous matrixes declined in the order of deionized water > Plastic Lake water > dechlorinated tap water, so other parameters must affect uptake into POCIS, although this influence will be minor. MAX-POCIS and MCX-POCIS showed little advantage over the commercial POCIS configuration for monitoring in natural waters.     

Emissions of unintentional persistent organic pollutants from open burning of municipal solid waste from developing countries

Open burning of waste is the most significant source of polychlorinated dibenzo-para-dioxins and dibenzofurans (PCDD/PCDF) in many national inventories prepared pursuant to the Stockholm Convention on Persistent Organic Pollutants. This is particularly true for developing countries. Emission factors for POPs such as PCDD/PCDF, dioxin-like polychlorinated biphenyls (dl-PCB) and penta- and hexachlorobenzenes (PeCBz/HCB) from open burning of municipal solid waste in China and Mexico are reported herein. Six different waste sources were studied varying from urban-industrial to semi-urban to rural. For PCDD/PCDF, the emission factors to air ranged from 3.0 to 650 ng TEQ kg⁻¹ waste and for dl-PCB from 0.092 to 54 ng TEQ kg⁻¹ waste. Emission factors for PeCBz (17-1200 ng kg⁻¹ waste) and HCB (24-1300 ng kg⁻¹ waste) spanned a wide but similar range. Within the datasets there is no indication of significant waste composition effect on emission factor with the exception of significantly higher Mexico rural samples.     

Emissions of biogenic VOC from forest ecosystems in central Europe: Estimation and comparison with anthropogenic emission inventory

This paper describes a method of estimating emission fluxes of biogenic volatile organic compounds (BVOCs) based on the approach proposed by Guenther et al. (1995) and the high-resolution Corine land-cover 2000 database (1 × 1 km resolution). The computed emission fluxes for the Czech Republic (selected for analysis as being representative of a heavily cultivated, central European country) are compared with anthropogenic emissions, both for the entire country and for individual administrative regions. In some regions, BVOC emissions are as high as anthropogenic emissions; however, in most regions the BVOC emissions are approximately 50% of the anthropogenic emissions. The yearly course of BVOC emissions (represented by monoterpenes and isoprene) is presented, along with the spatial distribution of annual mean values. Differences in emission distributions during winter (January) and summer (June) are also considered.     

Wood smoke as a source of particle-phase organic compounds in residential areas

The objective of this study was to investigate the organic composition of wood smoke emissions and ambient air samples in order to determine the wood smoke contribution to the ambient air pollution in the residential areas. From November 2005 to March 2006 particle-phase PM₁₀ samples were collected in the residential town Dettenhausen surrounded by forests near Stuttgart in southern Germany. Samples collected on pre-baked glass fibre filters were extracted using toluene with ultrasonic bath and analysed by gas chromatography mass spectrometry (GC-MS). 21 polycyclic aromatic hydrocarbons (PAH) including 16 USEPA priority pollutants, different organic wood smoke tracers, primarily 21 species of syringol and guaiacol derivatives, levoglucosan and its isomers mannosan, galactosan and dehydroabietic acid were detected and quantified in this study. The concentrations of these compounds were compared with the fingerprints of emissions from hardwood and softwood combustion carried out in test facilities at Universitaet Stuttgart and field investigations at a wood stove during real operation in Dettenhausen. It was observed that the combustion derived PAH was detected in higher concentrations than other PAH in the ambient air PM₁₀ samples. Syringol and its derivatives were found in large amounts in hardwood burning but were not detected in softwood burning emissions. On the other hand, guaiacol and its derivatives were found in both softwood and hardwood burning emissions, but the concentrations were higher in the softwood smoke compared to hardwood smoke. So, these compounds can be used as typical tracer compounds for the different types of wood burning emissions. In ambient air samples both syringol and guaiacol derivatives were found which indicates the wood combustion contribution to the PM load in such residential areas. Levoglucosan was detected in high concentrations in all ambient PM₁₀ samples. A source apportionment modelling, Positive Matrix Factorization (PMF) was implemented to quantify the wood smoke contribution to the ambient PM₁₀ bound organic compounds in the residential area.     

Ozonation of azo dye Acid Red 14 in a microporous tube-in-tube microchannel reactor: decolorization and mechanism

Despite the great success of time-weighted average passive sampling of hydrophobic contaminants, such as PCBs and PAHs, the sampling of polar organic compounds still presents a challenge because the equilibrium between water and most sampling phases is attained in a relatively short time. In this study, we proposed a new time-integrative sampler using in situ solvent extraction (TISIS) for polar organic chemicals. The sampler was composed of a 15 cm poly(dimethylsiloxane) (PDMS) tubing, with an internal diameter of 0.5 mm and wall thickness of 0.5 mm, through which an extraction solvent (acetonitrile) was passed. Four polar organic contaminants, caffeine, atrazine, diuron and 17α-ethynylestradiol, were chosen for the evaluation of the performance of the sampler. Without the use of in situ solvent extraction, the PDMS tubing when exposed to a constant aqueous concentration of the four model compounds was able to linearly accumulate those compounds for less than 12 h and equilibrium between the PDMS tubing and water was attained in 2 d under our laboratory conditions. However, TISIS when exposed to a constant aqueous concentration was able to linearly accumulate all the model compounds without any exposure time limitation. The measured sampling rates at three different extraction flow rates (0.2, 0.5, 1.5 mL min⁻¹) were similar, regardless of the chemicals, indicating that the overall mass transfer from aqueous solution to the extraction solvent was most likely dominated by partitioning to the PDMS tubing and the internal diffusion within PDMS. In addition, a pulsed exposure experiment confirmed that TISIS operated in a time-integrative mode when the environmental concentration was highly fluctuated.     

Potential of BAC combined with UVC/H2O2 for reducing organic matter from highly saline reverse osmosis concentrate produced from municipal wastewater reclamation

The organic matter present in the concentrate streams generated from reverse osmosis (RO) based municipal wastewater reclamation processes poses environmental and health risks on its disposal to the receiving environment (e.g., estuaries, bays). The potential of a biological activated carbon (BAC) process combined with pre-oxidation using a UVC/H₂O₂ advanced oxidation process for treating a high salinity (TDS ∼ 10 000 mg L⁻¹) municipal wastewater RO concentrate (ROC) was evaluated at lab scale during 90 d of operation. The combined treatment reduced the UVA₂₅₄ and colour of the ROC to below those for the influent of the RO process (i.e., biologically treated secondary effluent), and the reductions in DOC and COD were approximately 60% and 50%, respectively. UVC/H₂O₂ was demonstrated to be an effective means of converting the recalcitrant organic compounds in the ROC into biodegradable substances which were readily removed by the BAC process, leading to a synergistic effect of the combined treatment in degrading the organic matter. The tests using various BAC feed concentrations suggested that the biological treatment was robust and consistent for treating the high salinity ROC. Using Microtox analysis no toxicity was detected for the ROC after the combined treatment, and the trihalomethane formation potential was reduced from 3.5 to 2.8 mg L⁻¹.     

Smoke emissions from biomass burning in a Mediterranean shrubland

Gaseous and particulate samples from the smoke from prescribed burnings of a shrub-dominated forest with some pine trees in Lousã Mountain, Portugal, in May 2008, have been collected. From the gas phase Fourier transform infrared (FTIR) measurements, an average modified combustion efficiency of 0.99 was obtained, suggesting a very strong predominance of flaming combustion. Gaseous compounds whose emissions are promoted in fresh plumes and during the flaming burning phase, such as CO₂, acetylene and propene, produced emission factors higher than those proposed for savannah and tropical forest fires. Emission factors of species that are favoured by the smouldering phase (e.g. CO and CH₄) were below the values reported in the literature for biomass burning in other ecosystems. The chemical composition of fine (PM_2.5) and coarse (PM_2.5–10) particles was achieved using ion chromatography (water-soluble ions), instrumental neutron activation analysis (trace elements) and a thermal–optical transmission technique (organic carbon and elemental carbon). Approximately 50% of the particulate mass was carbonaceous in nature with a clear dominance of organic carbon. The organic carbon-to-elemental carbon ratios up to 300, or even higher, measured in the present study largely exceeded those reported for fires in savannah and tropical forests. More than 30 trace elements and ions have been determined in smoke aerosols, representing in total an average contribution of about 7% to the PM₁₀ mass.     

Emission factors of atmospheric and climatic pollutants from crop residues burning

Biomass burning is a common agricultural practice, because it allows elimination of postharvesting residues; nevertheless, it involves an inefficient combustion process that generates atmospheric pollutants emission, which has implications on health and climate change. This work focuses on the estimation of emission factors (EFs) of PM_2.5, PM₁₀, organic carbon (OC), elemental carbon (EC), carbon monoxide (CO), carbon dioxide (CO₂), and methane (CH₄) of residues from burning alfalfa, barley, beans, cotton, maize, rice, sorghum, and wheat in Mexico. Chemical characteristics of the residues were determined to establish their relationship with EFs, as well as with the modified combustion efficiency (MCE). Essays were carried out in an open combustion chamber with isokinetic sampling, following modified EPA 201-A method. EFs did not present statistical differences among different varieties of the same crop, but were statistically different among different crops, showing that generic values of EFs for all the agricultural residues can introduce significant uncertainties when used for climatic and atmospheric pollutant inventories. EFs of PM_2.5 ranged from 1.19 to 11.30 g kg^?1, and of PM₁₀ from 1.77 to 21.56 g kg^?1. EFs of EC correlated with lignin content, whereas EFs of OC correlated inversely with carbon content. EFs of EC and OC in PM_2.5 ranged from 0.15 to 0.41 g kg^?1 and from 0.33 to 5.29 g kg^?1, respectively, and in PM₁₀, from 0.17 to 0.43 g kg^?1 and from 0.54 to 11.06 g kg^?1. CO₂ represented the largest gaseous emissions volume with 1053.35–1850.82 g kg^?1, whereas the lowest was CH₄ with 1.61–5.59 g kg^?1. CO ranged from 28.85 to 155.71 g kg^?1, correlating inversely with carbon content and MCE. EFs were used to calculate emissions from eight agricultural residues burning in the country during 2016, to know the potential mitigation of climatic and atmospheric pollutants, provided this practice was banned.

Implications: The emission factors of particles, short-lived climatic pollutants, and atmospheric pollutants from the crop residues burning of eight agricultural wastes crops, determined in this study using a standardized method, provides better knowledge of the emissions of those species in Latin America and other developing countries, and can be used as inputs in air quality models and climatic studies. The EFs will allow the development of more accurate inventories of aerosols and gaseous pollutants, which will lead to the design of effective mitigation strategies and planning processes for sustainable agriculture.