SMX degradation by ozonation and UV radiation: a kinetic study

The rate constants of sulfamethoxazole (SMX) degradation by ozonation and UV₂₅₄ radiation were investigated under various parameters including influent ozone gas concentration, initial SMX concentration, UV light intensity, ionic strength, water quality in terms of varying anions (bicarbonate, sulfate and nitrate), humic acid (HA) and pH. The results indicated that the removal of SMX by ozonation and UV₂₅₄ radiation fitted well to a pseudo first-order kinetic model and the rate constants were in the range of (0.9-9.8) × 10⁻³ and (1.7-18.9) × 10⁻³ s⁻¹, respectively. The second-order rate constants of SMX with ozone (k_O3), under varying operational parameters, were also determined and varied in the range of (0.60-3.38) ± 0.13 × 10⁵ M⁻¹ s⁻¹. In addition, SMX degradation through UV pretreatment followed by ozonation in the presence of HA was proved to be an effective method which can remove SMX with a low ozone dose. The results suggested that ozonation of SMX was more affected by concentration of influent ozone gas, alkalinity, and HA, while incident UV light intensity, pH, and HA were the dominant factors influencing UV degradation of SMX.     

Metal contamination of short-term snow cover near urban crossroads: correlation analysis of metal content and fine particles distribution

Snow samples were collected near crossroads in Novi Sad, Serbia, during December 2009 to assess metal concentrations (Ca, K, Zn, Fe, Cu, Mn, Al, Pb and Na), fine particle distribution and pH value. The filtered samples of melted snow were analysed, with a focus on particles smaller than a few μm. The most common values of the frequency number distribution curve were either in the range of 0.05-0.07 μm or one order of magnitude higher (0.2-0.5 μm). At examined locations metal concentrations varied from 0.0004 mg L⁻¹ for Pb to 18.9 mg L⁻¹ for Na. Besides Na, which mostly originated from de-icing salt, Ca is found to be the most abundant element in snow indicating the dominant influence of natural factors on snow chemistry. No significant difference was found in concentration of the elements at locations near crossroads with either low or high traffic volume, except for Na and Zn.To investigate how metals were related a correlation analysis was done for the concentrations of metals and with respect to the particle size distribution parameters and pH values. The major influence on the fine particle volume (mass) was concluded to be due to the elements from anthropogenic sources. This conclusion was based on the significant positive correlation between Fe, Zn and Al and the fine particle volume based distribution parameters.     

Selenium speciation in acidic environmental samples: application to acid rain-soil interaction at Mount Etna volcano

Speciation plays a crucial role in elemental mobility. However, trace level selenium (Se) speciation analyses in aqueous samples from acidic environments are hampered due to adsorption of the analytes (i.e. selenate, selenite) on precipitates. Such solid phases can form during pH adaptation up till now necessary for chromatographic separation. Thermodynamic calculations in this study predicted that a pH < 4 is needed to prevent precipitation of Al and Fe phases. Therefore, a speciation method with a low pH eluent that matches the natural sample pH of acid rain-soil interaction samples from Etna volcano was developed. With a mobile phase containing 20 mM ammonium citrate at pH 3, selenate and selenite could be separated in different acidic media (spiked water, rain, soil leachates) in <10 min with a LOQ of 0.2 μg L⁻¹ using ⁷⁸Se for detection. Applying this speciation analysis to study acid rain-soil interaction using synthetic rain based on H₂SO₄ and soil samples collected at the flanks of Etna volcano demonstrated the dominance of selenate over selenite in leachates from samples collected close to the volcanic craters. This suggests that competitive behavior with sulfate present in acid rain might be a key factor in Se mobilization. The developed speciation method can significantly contribute to understand Se cycling in acidic, Al/Fe rich environments.     

Adsorption and breakdown of penicillin antibiotic in the presence of titanium oxide nanoparticles in water

The fate and transport of antibiotics in natural water systems is controlled in part by interactions with nanometer (10⁻⁹ m) metal oxide particles. Experiments were performed by mixing solutions of ampicillin (AMP), a common, penicillin-class human and veterinary antibiotic, with 25 nm-TiO₂ (anatase) nanoparticles at different pH conditions. Both sorption and degradation of AMP were observed in the AMP-nanoparticle solutions. For AMP concentrations from ∼3 μM to 2.9 mM the overall AMP removal from solution can be described by linear isotherms with removal coefficients (K_r) of 3028 (±267) L kg⁻¹ at pH 2, 11,533 (±823) L kg⁻¹ at pH 4, 12,712 (±672) L kg⁻¹ at pH 6, and 1941 (±342) L kg⁻¹ at pH 8. Mass spectral analysis of AMP solutions after removal of the solid nanoparticles yielded ions that indicate the presence of peniclloic acid, penilloic acid and related de-ammoniated by-products as possible compounds resulting from the degradation of AMP at the TiO₂ surface.     

Suitability of a magnetic particle immunoassay for the analysis of PBDEs in Hawaiian euryhaline fish and crabs in comparison with gas chromatography/electron capture detection-ion trap mass spectrometry

A gas chromatograph/electron capture detector-ion trap mass spectrometer (GC/ECD-ITMS) was used for the determination of polybrominated diphenyl ethers (PBDEs) in euryhaline fish and crabs. GC/ECD-ITMS results showed that average recoveries from the spiked fish samples are in a range of 58-123% with relative standard deviations (RSDs) of 5-19%. PBDE concentrations obtained from GC/ECD-ITMS ranged from 28 ng/g to 1845 ng/g lipid weight (lw) in all aquatic species collected from Hawaiian brackish waters. The general BDE congener concentration profile observed in this study is BDE-47 > BDE-100 > BDE-154 > BDE-99 > BDE-153 > BDE-28 > BDE-183. The ELISA results expressed as BDE-47 equivalents correlated well with those of GC/ECD-ITMS, with a correlation coefficient (R² = 0.68) and regression coefficient (slope = 0.82). Comparison of ELISA with GC/ECD-ITMS results demonstrated that ELISA provides a timely and cost-effective method to screen PBDEs in fish and crab samples.     

Thermodynamic and kinetic study of phenol degradation by a non-catalytic wet air oxidation process

This work is dedicated to an accurate evaluation of thermodynamic and kinetics aspects of phenol degradation using wet air oxidation process. Phenol is a well known polluting molecule and therefore it is important having data of its behaviour during this process. A view cell is used for the experimental study, with an internal volume of 150 mL, able to reach pressures up to 30 MPa and temperatures up to 350 °C. Concerning the thermodynamic phase equilibria, experimental and modelling results are obtained for different binary systems (water/nitrogen, water/air) and ternary system (water/nitrogen/phenol). The best model is the Predictive Soave Redlich Kwong one. This information is necessary to predict the composition of the gas phase during the process. It is also important for an implementation in a process simulation. The second part is dedicated to kinetics evaluation of the degradation of phenol. Different compounds have been detected using GC coupled with a MS. A kinetic scheme is deduced, taking into account the evolution of phenol, hydroquinones, catechol, resorcinol and acetic acid. The kinetic parameters are calculated for this scheme. These data are important to evaluate the evolution of the concentration of the different polluting molecules during the process. A simplified kinetic scheme, which can be easily implemented in a process simulation, is also determined for the direct degradation of phenol into H₂O and CO₂. The Arrhenius law data obtained for the phenol disappearance are the following: k = 1.8 × 10⁶ ± 3.9 × 10⁵ M⁻¹ s⁻¹ (pre-exponential factor) and E_a = 77 ± 8 kJ mol⁻¹ (activation energy).     

Spatial distribution of organochlorine contaminants in soil, sediment, and fish in Bikini and Enewetak Atolls of the Marshall Islands, Pacific Ocean

Several nuclear tests were performed at Enewetak and Bikini Atolls in the Marshall Islands between 1946 and 1958. The events at Bikini Atoll involved several ships that were tested for durability during nuclear explosions, and 24 vessels now rest on the bottom of the Bikini lagoon. Nine soil samples were collected from different areas on the two islands of the atoll, and eighteen sediment, nine fish, and one lobster were collected in the vicinity of the sunken ships. Organochlorine pesticides (OCPs), polychlorinated biphenyls (PCBs), and polychlorinated terphenyls (PCTs) in these samples were analyzed using gas chromatography/ion trap mass spectrometry (GC/ITMS). The average recoveries ranged from 78% to 104% for the different PCB congeners. The limits of detection (LOD) for PCBs, PCTs, DDE, DDT, and dieldrin ranged 10-50 pg g⁻¹. Some fish from Enewetak contained PCBs at a concentration range of 37-137 ng g⁻¹, dry weight (dw), and most of the soils from Enewetak showed evidence of PCBs (22-392 ng g⁻¹ dw). Most of the Bikini lagoon sediment samples contained PCBs, and the highest was the one collected from around the Saratoga, an aircraft carrier (1555 ng g⁻¹ dw). Some of the fish samples, most of the soil samples, and only one of the sediment samples contained 2,2-bis(4-chlorophenyl)-1,1-dichloroethylene (DDE) and PCBs. In addition to PCBs, the soils from Enewetak Atoll contained PCTs. PCTs were not detected in the sediment samples from Bikini Atoll. The results suggest local pollution sources of PCBs, PCTs, and OCPs.     

Influence of aggregated particles on biodegradation activities for dimethylarsinic acid (DMA) in Lake Kahokugata

Aquatic arsenic cycles mainly depend on microbial activities that change the arsenic chemical forms and influence human health and organism activities. The microbial aggregates degrading organic matter are significantly related to the turnover between inorganic arsenic and organoarsenic compounds. We investigated the effects of microbial aggregates on organoarsenic mineralization in Lake Kahokugata using lake water samples spiked with dimethylarsinic acid (DMA). The lake water samples converted 1 μmol L⁻¹ of DMA to inorganic arsenic for 28 d only under anaerobic and dark conditions in the presence of microbial activities. During the DMA mineralization process, organic aggregates >5.0 μm with bacterial colonization increased the densities. When the organic aggregates >5.0 μm were eliminated from the lake water samples using filters, the degradation activities were reduced. DMA in the lake water would be mineralized by the microbial aggregates under anaerobic and dark conditions. Moreover, DMA amendment enhanced the degradation activities in the lake water samples, which mineralized 50 μmol L⁻¹ of DMA. The DMA-amended aggregates >5.0 μm completely degraded 1 μmol L⁻¹ of DMA with a shorter incubation time of 7 d. The supplement of KNO₃ and NaHCO₃ to lake water samples also shortened the DMA-degradation period. Presumably, the bacterial aggregates involved in the chemical heterotrophic process would contribute to the DMA-biodegradation process in Lake Kahokugata, which is induced by the DMA amendment.     

Sorption of chlorinated solvents and degradation products on natural clayey tills

The sorption of chlorinated solvents and degradation products on seven natural clayey till samples from three contaminated sites was investigated by laboratory batch experiments in order to obtain reliable sorption coefficients (K_d values). The sorption isotherms for all compounds were nearly linear, but fitted by Freundlich isotherms slightly better over the entire concentration range. For chloroethylenes, tetrachloroethylene (PCE) was most strongly sorbed to the clayey till samples (K_d = 0.84-2.45 L kg⁻¹), followed by trichloroethylene (TCE, K_d = 0.62-0.96 L kg⁻¹), cis-dichloroethylene (cis-DCE, K_d = 0.17-0.82 L kg⁻¹) and vinyl chloride (VC, K_d = 0.12-0.36 L kg⁻¹). For chloroethanes, 1,1,1-trichloroethane (1,1,1-TCA) was most strongly sorbed (K_d = 0.2-0.45 L kg⁻¹), followed by 1,1-dichloroethane (1,1-DCA, K_d = 0.16-0.24 L kg⁻¹) and chloroethane (CA, K_d = 0.12-0.18 L kg⁻¹). This is consistent with the order of hydrophobicity of the compounds. The octanol-water coefficient (log K_ow) correlated slightly better with log K_d values than log K_oc values indicating that the K_d values may be independent of the actual organic carbon content (f_oc). The estimated log K_oc or log K_d for chlorinated solvents and degradation products determined by regression of data in this study were significantly higher than values determined by previously published empirical relationships. The site specific K_d values as well as the new empirical relationship compared well with calculations on water and soil core concentration for cis-DCE and VC from the Rugårdsvej site. In conclusion, this study with a wide range of chlorinated ethenes and ethanes - in line with previous studies on PCE and TCE - suggest that sorption in clayey tills could be higher than typically expected.     

Environmental occurrence and fate of semifluorinated n-alkanes in snow and soil samples from a ski area

Semifluorinated n-alkanes (SFAs) with carbon chain lengths of 22 to approximately 36 atoms are present in fluorinated ski waxes to reduce the friction between ski base and snow, resulting in a better glide. Semifluorinated n-alkenes (SFAenes) are byproducts in the production process of SFAs and are also found in ski waxes. Snow and soil samples from a ski area in Sweden were taken after a large skiing competition and after snowmelt, respectively, and analyzed for SFAs and SFAenes. Single analyte concentrations in snow (analyzed as melt water) ranged from a few ng L⁻¹ up to 300 μg L⁻¹. ∑SFA concentrations decreased significantly from the start to the finish of the ski trail. Single analyte concentrations in soil ranged up to 9 ng g⁻¹ dw. ∑SFA concentrations in soil did not show a trend along the ski trail. This may be due to the fact that concentrations in soil, although strongly influenced by the competition, reflect inputs during the whole skiing season. The chemical inventory in snow was greater than the inventory in soil for shorter chain SFAs (C₂₂C₂₈) and for all SFAenes. Additionally, a significant change in SFA patterns between snow and soil samples was found. These observations suggested volatilization of shorter chain SFAs and of SFAenes during snowmelt. Evidence for long-term accumulation of SFAs in surface soil over several skiing seasons was not found.     

Peroxymonosulfate-Co(II) oxidation system for the removal of the non-ionic surfactant Brij 35 from aqueous solution

The non-ionic surfactant Brij 35 was effectively removed from concentrated aqueous solution by the peroxymonosulfate/Co(II) system, using oxone (2KHSO₅·KHSO₄·K₂SO₄) as a source of peroxymonosulfate. At pH = 2.3 and initial Brij 35 concentration in the range 680-2410 mg L⁻¹, 86-94% removal was achieved after 24 h, using Co(II) = 15 μM and oxone = 5.9 mM. The effectiveness of removal did not change when initial pH was in the range 2.3-8.2. After five subsequent additions of Co(II) and oxone to the solution, COD and TOC removals increased up to 64% and 33%, respectively. Radical quenching tests confirmed that sulfate radical was the dominant radical species in the system. The main identified by-products from surfactant degradation were: (a) low molecular weight organic acids; (b) aldehydes and formates with shorter ethoxy chain than Brij 35; (c) alcohol ethoxylates carrying hydroxyl groups bonded to ethoxy chain. By-products identification allowed to hypothesize the pathways of Brij 35 degradation.     

Major inorganic ions in North Pole snow samples

Major inorganic ions, pH, total N and P were analyzed in eight arctic snow samples collected in March, April and May 1984 during an expedition in the North Pole region (N83₀18′ W73₀06′ - N89.960₀). The concentrations of the ions in different samples were close to each other and the values obtained seem to be representative for mean concentrations in the snow. In the sample taken from the North Pole the pH value was 5.00 while the H⁺-, SO^2?₄- and NO^?₃-concentrations were 0.24, 6.2 and 4.3 μmol/l, respectively. The concentrations are exceedingly low and agree very well with earlier results from arctic snow samples.     

Temperature and water pressure head effects on the degradation of the diketonitrile metabolite of isoxaflutole in a loamy soil under two tillage systems

Laboratory studies were conducted to evaluate the effects of temperature and water pressure head on the degradation of the diketonitrile metabolite (DKN) of isoxaflutole during 84 d in samples collected in a loamy soil under conventional (CT) and conservation (MT) tillage systems. Soil temperature was the major factor controlling DKN degradation in the two tillage systems. The shortest half-lives (T_1/2) were measured in the seedbed samples under MT at 25 °C and −33 cm water pressure head. We found that mouldboard ploughing under CT was responsible for the spatial variability of herbicide degradation properties, whereas under MT herbicide degradation was associated to the vertical distribution of organic matter.     

Zamzam water: concentration of trace elements and other characteristics

Many Muslims drink Zamzam water for use either medicinally or religiously. Millions of pilgrims drink it and take bottles of it to their home countries. Heated scientific and political debates appeared after BBC reported in May 2011 that Zamzam water is poisonous, because of the high levels of arsenic. The World Health Organizations classifies arsenic as a human carcinogen, but some types of arsenic are also used as medicines. Adequate scientific studies on the Zamzam water are absent. This paper will provide, for the first time, basic and comprehensive information regarding the geochemical properties of Zamzam water for more than 30 indicators and using the state-of-the-art laboratory facilities. The data will help us to understand the sources of pollution under discussion, reactions at both local and international levels; and will highlight the potential healing capacity of Zamzam water. Thirty Zamzam water samples were collected by three distinct methods; from 10 pilgrims living in different locations in Germany in 2007, 10 samples from shops in Frankfurt and Berlin in 2011, and 10 samples directly from Makkah in 2011. The samples were analyzed 2 weeks after collection for more than 30 indicators: pH, EC, Eh, Cl, F, Br, NO₃, PO₄, SO₄, HCO₃, Ag, Al, As, Ba, Ca, Cd, Co, Cr, Cu, Fe, K, Mg, Mn, Na, Ni, Pb, Sr, and Zn beside others. Four major instruments were used; the IC, the ICPOES, the ICPMS and the HGAAS. The quality of the water did not change for 2 years and there was an excellent agreement among the results of the 30 water samples as well as between the results of the 2 years for the same samples analyzed in 2007 and 2008. The water is alkaline (average pH is 8) with an average Li concentration of 15 μg L⁻¹. The average concentrations of As and NO₃ showed values three times higher than the WHO standards (27 μg L⁻¹ and 150 mg L⁻¹, respectively). The averages of Ca and K were 95 and 50 mg L⁻¹, respectively. Very urgent steps are required to scientifically screen for the elevated parameters As, NO₃, Ca, and K in all Zamzam water sources and locations with full transparency. The resultant information should be made available to the public, and the relationship between pollution and human health should be addressed. The alkalinity of Zamzam water and the presence of trace amounts of As and Li may cause the healing power. However, a scientific strategy should be developed and adopted to enable further research and studies on toxicology and treatment technologies could be applied if needed.     

Photolytic and photocatalytic degradation of 6-chloronicotinic acid

This work describes for the first time the photolytic and photocatalytic degradation of 6-chloronicotinic acid (6CNA) in double deionised water, which is a degradation product of neonicotinoid insecticides imidacloprid and acetamiprid, and it is known to appear in different environmental matrices. Photolytic experiments were performed with three UVA (ultraviolet A) polychromatic fluorescent lamps with broad maximum at 355 nm, while photocatalytic experiments were performed using immobilised titanium dioxide (TiO₂) on six glass slides in the spinning basket inside a photocatalytic quartz cell under similar irradiation conditions. Photolytic degradation revealed no change in concentration of 6CNA within 120 min of irradiation, while the photocatalytic degradation within 120 min, obeyed first-order kinetics. The observed disappearance rate constant was k = 0.011 ± 0.001 min⁻¹ and t_1/2 was 63.1 ± 5.5 min. Mineralisation rate was estimated through total organic carbon (TOC) and measurements revealed no carbon removal in case of photolysis after 120 min of exposure. However in photocatalytic experiments 46 ± 7% mineralisation was achieved within 120 min of irradiation. Nevertheless, the removal of total nitrogen (TN) was not observed across all experiments. Ion chromatographic analyses indicated transformation of chlorine atoms to chloride and increase of nitrate(V) ions only via photocatalytic experiments. Efficiency of selected advanced oxidation process (AOP) was investigated through toxicity assessment with Vibrio fischeri luminescent bacteria and revealed higher adverse effects of treated samples on bacteria following photocatalytic degradation in spite of the fact that higher mineralisation was achieved. New hydroxylated product generated in photocatalytic experiments with TiO₂, was confirmed with liquid chromatography-electro spray ionisation mass spectrometry (LC-ESI-MS/MS) analyses, gas chromatography-mass spectrometry (GC-MS) and nuclear magnetic resonance spectroscopy (¹H NMR).     

Perfluorinated compounds in Haihe River and Dagu Drainage Canal in Tianjin, China

In this study, nine perfluorinated compounds (PFCs) were investigated in water and sediment of Haihe River (HR) and Dagu Drainage Canal (DDC), Tianjin, China. The total PFCs in water samples from DDC (40-174 ng L⁻¹) was much greater than those from HR (12-74 ng L⁻¹). PFC contamination was severe at lower reaches of HR due to industry activities, while high PFCs were found in the middle of DDC due to the effluents from wastewater treatment plants. Perfluorohexanoic acid (PFHxA), perfluorooctanoic acid (PFOA) and perfluorooctane sulfonate (PFOS) were the predominant PFCs in aqueous phase. The total PFCs in sediments from DDC (1.6-7.7 ng g⁻¹ dry weight) were lower as compared to HR (7.1-16 ng g⁻¹), maybe due to the dredging of sediment in DDC conducted recently. PFOS was the major PFC in HR sediments followed by PFOA; while PFHxA was the major PFC in DDC sediments. Organic carbon calibrated sediment-water distribution coefficients (K_OC) were calculated for HR. The Log K_OC ranged from 3.3 to 4.4 for C7-C11 perfluorinated carboxylic acids, increasing by 0.1-0.6 log units with each additional CF₂ moiety. The log K_OC for 8:2 fluorotelomer unsaturated acid was reported for the first time with a mean value of 4.0. The log Koc of PFOS was higher than perfluoronanoic acid by 0.8 log units.     

Microbial degradation of pharmaceuticals in estuarine and coastal seawater

Microbial degradation rates were measured for 19 pharmaceuticals in estuarine and coastal surface water samples. Antipyrine, carbamazepine, cotinine, sulfamethoxazole, and trimethoprim were the most refractory (half-lives, t_1/2 = 35 to >100 days), making them excellent candidates for wastewater tracers. Nicotine, acetaminophen, and fluoxetine were labile across all treatments (t_1/2 = 0.68-11 days). Caffeine, diltiazem, and nifedipine were also and relatively labile in all but one of the treatments (t_1/2 = 3.5-13 days). Microbial degradation of caffeine was further confirmed by production ¹⁴CO₂. The fastest decay of non-refractory compounds was always observed in more sewage-affected Jamaica Bay waters. Degradation rates for the majority of these pharmaceuticals are much slower than reported rates for small biomolecules, such as glucose and amino acids. Batch sorption experiments indicate that removal of these soluble pharmaceuticals from the water column to sediments is a relatively insignificant removal process in these receiving waters.     

Comparative survey of levels of chlorinated cyclodiene pesticides in breast milk from some cities of China, Korea and Japan

Exposure of mothers to organochlorine pesticides (OCPs) was assessed by measuring the levels of 20 OCPs in 70 human breast milk samples pooled from 210 individuals from China, Korea and Japan. The OCPs were analyzed using gas chromatography/mass spectrometry (GC/MS) in electron capture negative ionization (ECNI) monitoring. The results showed that β-hexachlorocyclohexane and hexachlorobenzene were one order of magnitude higher in China than in the other nations, whereas chlordanes and polychlorinated biphenyl levels were highest in Japan. Heptachlor epoxide, dieldrin, endrin, toxaphenes and mirex were detected in most samples, and levels of these chemicals were significantly higher in Japan (0.8-4.5 ng g⁻¹ lipid), followed by Korea (0.2-4.7 ng g⁻¹ lipid), and lowest in China (less than 1.0 ng g⁻¹ lipid). α- and β-endosulfans were detected at a range of 0.9-1.5 ng g⁻¹ lipid levels in all samples analyzed, and their levels were higher in Korean than in Chinese samples.     

Distribution of perfluorinated compounds in surface water from Hanjiang River in Wuhan,China

This study provided the first spatial distribution of perfluorinated compounds (PFCs) in Hanjiang River in Wuhan, China (HR). Surface water samples, collected from 23 sites in HR were analyzed for eight PFCs. The total concentrations of PFCs ranged from 8.90 to 568 ng L⁻¹, while perfluoropentanoic acid (PFOA, <LOQ − 256 ng L⁻¹) and perfluorooctane sulfonate (PFOS, <LOQ − 88.9 ng L⁻¹) dominated. All data were found to be normally distributed in the river. Similar spatial distribution tendencies were found among perfluorocarboxylates (PFCAs) and significant correlations were observed among PFCAs, while no significant correlations were found between PFOS and PFCAs. The distributions of PFCs were highly influenced by the industrial discharge and urban activities. The flux of PFCs from HR to the Yangtze River was estimated in the range of 16.9–127 kg yr⁻¹. More than a half of the samples studied could not meet the drinking water standards and avian wildlife values, suggesting further studies of characterizing PFCs and their potential risk to human were needed.     

Photocatalytic decomposition of crotamiton over aqueous TiO(2) suspensions: determination of intermediates and the reaction pathway

The photocatalytic degradation of crotamiton in aqueous solution using TiO₂ was investigated. To investigate the effect of initial pH, the photodegradation behaviors of three types of pharmaceuticals were compared (crotamiton, clofibric acid, sulfamethoxazole). The degradation rates of crotamiton in the pH range 3-9 were nearly equal, but those of clofibric acid and sulfamethoxazole were affected by pH. At pH > 6.5, TiO₂ particles, clofibric acid and sulfamethoxazole had negative charge, therefore, the repulsive force between TiO₂ particles and anionic pharmaceuticals occurred and a low reaction rate at high pH was observed. The effect of UV intensity and TiO₂ concentration on photodegradation efficiency was also investigated. Linear and logarithmical relationships between UV intensity, TiO₂ concentration and the reaction rate constant were confirmed. Furthermore, the structures of photodegradation intermediates formed concomitantly with the disappearance of crotamiton were estimated. Seven intermediates were characterized by LC/MS/MS analyses, and it was assumed that the photocatalytic degradation of crotamiton was initiated by the attack of electrophilic hydroxyl radicals on aromatic rings and alkyl chains.