Solvent tolerant marine bacterium Bacillus aquimaris secreting organic solvent stable alkaline cellulase

The organic solvent tolerant bacteria with their physiological abilities to decontaminate the organic pollutants have potentials to secrete extracellular enzymes of commercial importance. Of the 19 marine bacterial isolates examined for their solvent tolerance at 10 vol.% concentration, one had the significant tolerance and showed a relative growth yield of 86% for acetone, 71% for methanol, 52% for benzene, 35% for heptane, 24% for toluene and 19% for ethylacetate. The phylogenetic analysis of this strain using 16S rDNA sequence revealed 99% homology with Bacillus aquimaris. The cellulase enzyme secreted by this strain under normal conditions showed an optimum activity at pH 11 and 45 °C. The enzyme did show functional stability even at higher pH (12) and temperature (75 °C) with residual activity of 85% and 95% respectively. The enzyme activity in the presence of different additives were in the following order: Co⁺² > Fe⁺² > NaOCl₂ > CuSO₄ > KCl > NaCl. The enzyme stability in the presence of solvents at 20 vol.% concentration was highest in benzene with 122% followed by methanol (85%), acetone (75%), toluene (73%) and heptane (42%). The pre-incubation of enzyme in ionic liquids such as 1-ethyl-3-methylimidazolium methanesulfonate and 1-ethyl-3-methylimidazolium bromide increased its activity to 150% and 155% respectively. The change in fatty acid profile with different solvents further elucidated the physiological adaptations of the strain to tolerate such extreme conditions.     

Distribution of Se and its species in Myriophyllum spicatum and Ceratophyllum demersum growing in water containing Se (VI)

The uptake of Se (VI) by two aquatic plants, Myriophyllum spicatum L. and Ceratophyllum demersum L., and its effects on their physiological characteristics have been studied. Plants were cultivated outdoors under semi-controlled conditions and in two concentrations of Na selenate solution (20 μg Se L⁻¹ and 10 mg Se L⁻¹). The higher dose of Se reduced the photochemical efficiency of PSII in both species, while the lower dose had no effect on PSII. Addition of Se had no effect on the amounts of chlorophyll a and b. The concentration of Se in plants grown in 10 mg Se L⁻¹, averaged 212 ± 12 μg Se g⁻¹ DM in M. spicatum (grown from 8-13 d), and 492 ± 85 μg Se g⁻¹ DM in C. demersum (grown for 31 d). Both species could take up a large amount of Se. The amount of soluble Se compounds in enzyme extracts ranged from 16% to 26% in control, and in high Se solution from 48% to 36% in M. spicatum and C. demersum, respectively. Se-species were determined using HPLC-ICP-MS. The main soluble species in both plants was selenate (∼37%), while SeMet and SeMeSeCys were detected at trace levels.     

Selenium speciation in acidic environmental samples: application to acid rain-soil interaction at Mount Etna volcano

Speciation plays a crucial role in elemental mobility. However, trace level selenium (Se) speciation analyses in aqueous samples from acidic environments are hampered due to adsorption of the analytes (i.e. selenate, selenite) on precipitates. Such solid phases can form during pH adaptation up till now necessary for chromatographic separation. Thermodynamic calculations in this study predicted that a pH < 4 is needed to prevent precipitation of Al and Fe phases. Therefore, a speciation method with a low pH eluent that matches the natural sample pH of acid rain-soil interaction samples from Etna volcano was developed. With a mobile phase containing 20 mM ammonium citrate at pH 3, selenate and selenite could be separated in different acidic media (spiked water, rain, soil leachates) in <10 min with a LOQ of 0.2 μg L⁻¹ using ⁷⁸Se for detection. Applying this speciation analysis to study acid rain-soil interaction using synthetic rain based on H₂SO₄ and soil samples collected at the flanks of Etna volcano demonstrated the dominance of selenate over selenite in leachates from samples collected close to the volcanic craters. This suggests that competitive behavior with sulfate present in acid rain might be a key factor in Se mobilization. The developed speciation method can significantly contribute to understand Se cycling in acidic, Al/Fe rich environments.     

Photocatalytic inactivation of Escherichia coli by natural sphalerite suspension: effect of spectrum, wavelength and intensity of visible light

The photocatalytic disinfection of Escherichia coli K-12 is investigated by the natural sphalerite (NS) under different spectra, wavelengths and intensities of visible light (VL) emitted by light-emitting-diode lamp (LED). The spectrum effect of VL on disinfection efficiency is studied by using white LED, fluorescent tube (FT) and xenon lamp (XE), which indicates that the “discreted peak spectrum” of FT is more effective to inactivate bacteria than “continuous spectrum” of LED and XE. Besides, the photocatalytic disinfection of bacteria is compared under different single spectrum (blue, green, yellow and red color) LEDs. The results show that the most effective wavelength ranges of VL for photocatalytic disinfection with the NS are 440-490 and 570-620 nm. Furthermore, a positive relationship is obtained between the disinfection efficiency and the VL intensity. The experiment shows that NS can completely inactivate 10⁷ cfu mL⁻¹E. coli K-12 within 8 h irradiation by white LED with the intensity of 200 mW cm⁻² at pH 8. Moreover, the destruction process of the cell wall and the cell membrane are directly observed by TEM. Finally, no bacterial colony can be detected within a 96 h regrowth test of inactivated bacteria, which reveals that the VL-photocatalytic disinfection leads to an irreversible damage to the bacterial cells.     

Selenium fractions in organic matter from Se-rich soils and weathered stone coal in selenosis areas of China

A high degree of association between Selenium (Se) and organic matter has been demonstrated in natural environments, but Se fractions and speciation in organic matter is unclear. In this study, a method for quantifying organic matter associated with Se (OM-Se) was developed to investigate Se fractions in organic matter in Se-rich soils and weathered stone coal from Enshi, China, where Se poisoning of humans and livestock has been documented. Initially, Se was extracted using water and a phosphate buffer. Subsequently, OM-Se was extracted using NaOH, and then speciated into Se associated with fulvic acids (FA-Se) and humic acids (HA-Se). Both FA-Se and HA-Se were further speciated into the weakly bound and strongly bound fractions using a customized hydride generation reactor. The results show that FA-Se (1.91-479 mg kg⁻¹) is the predominant form of Se in all Se-rich soils and the weathered stone coal samples, accounting for more than 62% of OM-Se (3.07-484 mg kg⁻¹). Weakly bound FA-Se (1.33-450 mg kg⁻¹) was prevalent in the total FA-Se, while weakly bound HA-Se (0.62-26.2 mg kg⁻¹) was variable in the total HA-Se (1.15-32.5 mg kg⁻¹). These data indicate that OM-Se could play a significant source and sink role in the biogeochemical cycling of Se in the supergene environment. Weakly bound FA-Se seems to act as a potential source for bioavailable Se, whereas strongly bound HA-Se is a possible OM-Se sink which is not readily transformed into bioavailable Se.     

Effect of fungicides on plant growth promoting activities of phosphate solubilizing Pseudomonasputida isolated from mustard (Brassica compestris) rhizosphere

This study was navigated to examine the effects of fungicide-stress on the activities of plant-growth-promoting rhizobacterium Pseudomonasputida with inherent phosphate solubilizing activity. The fungicide-tolerant and phosphate solubilizing P.putida strain PS9 was isolated from the mustard rhizosphere and tentatively identified following standard morphological, physiological and biochemical tests. To further consolidate the identity of the strain PS9, the 16S rDNA sequence analysis was performed. Following the BLAST program, the strain PS9 was identified as P.putida. In the presence of the varying concentrations (0-3200 μg mL⁻¹; at a two fold dilution interval) of four fungicides of different chemical families (tebuconazole, hexaconazole, metalaxyl and kitazin) amended in minimal salt agar medium, the P.putida strain PS9 showed a variable tolerance levels (1400-3200 μg mL⁻¹) against the tested fungicides. The strain PS9 produced plant-growth-promoting (PGP) substances in significant amount in the absence of fungicides. In general, fungicides applied at the recommended, two and three times of the recommended rates, decreased the PGP attributes of P.putida the strain PS9 and affected the PGP activities in concentration-dependent manner. Fungicides at the recommended dose had minor reducing effect while the doses higher than the recommended dose significantly reduced the PGP activities (phosphate solubilization, salicylic acid, 2,3-dihydroxy benzoic acid, and indole-3-acetic acid production except exo-polysaccharides, hydrogen cyanate and ammonia production). Of the four fungicides, tebuconazole generally, showed maximum toxicity to the PGP activities of the strain PS9. This study inferred that fungicides must be examined in vitro for their possible adverse effects on soil micro flora before their application in agricultural fields. Moreover, the results also suggested the prerequisite of application of fungicide-tolerant PGPR strains as bioinoculants so that their PGP activities may not be suppressed under fungicide stress.     

Absorption of selenium by Lactuca sativa as affected by carboxymethylcellulose

Several organic compounds of high molecular weight present in soil interact with selenium and may act as active binding agents affecting its availability in soil, and, consequently, selenium uptake by plants. This study is aimed at investigating the effects of polysaccharides on selenium speciation in soil and on selenium absorption by Lactuca sativa L. plants. Three-week-old seedlings were transplanted into pots filled with soil, and sodium selenite at rates of 1.5 and 5mgSekg(-1) of soil, or sodium selenate at a rate of 1.5mgSekg(-1) of soil were applied. Carboxymethylcellulose (CMC) was added to the soil at rates of 0, 3 and 30mgkg(-1) of soil. After 48 and 110d from transplanting plants were harvested, separated into root and shoot, and fresh and dry matter weights were recorded. Total selenium was determined in both soil and plant samples. A sequential extraction was used to investigate the different Se oxidation states and assess the availability of Se in soil after the final harvesting. Both selenite and selenate were absorbed by roots, but plants amended with Se(VI+) showed higher selenium concentration than plants amended with Se(IV+). Selenite appears to be less mobile than selenate both in soil and plants. The addition of carboxymethylcellulose to soil decreased the amount of selenium absorbed by plants. CMC interacted with Se, making it less mobile as evidenced by the increase in the insoluble fractions. The insoluble Se forms in soil may represent environmental Se sinks potentially available for plants if the substrate is re-used for subsequent growth cycles and selenium species are mobilized as a result of biological and chemical processes.     

Effect of metals on a siderophore producing bacterial isolate and its implications on microbial assisted bioremediation of metal contaminated soils

A bacterial isolate producing siderophore under iron limiting conditions, was isolated from mangroves of Goa. Based on morphological, biochemical, chemotaxonomical and 16S rDNA studies, the isolate was identified as Bacillus amyloliquefaciens NAR38.1. Preliminary characterization of the siderophore indicated it to be catecholate type with dihydroxy benzoate as the core component. Optimum siderophore production was observed at pH 7 in mineral salts medium (MSM) without any added iron with glucose as the carbon source. Addition of NaCl in the growth medium showed considerable decrease in siderophore production above 2% NaCl. Fe⁺² and Fe⁺³ below 2 μM and 40 μM concentrations respectively, induced siderophore production, above which the production was repressed. Binding studies of the siderophore with Fe⁺² and Fe⁺³ indicated its high affinity towards Fe⁺³. The siderophore concentration in the extracellular medium was enhanced when MSM was amended with essential metals Zn, Co, Mo and Mn, however, decreased with Cu, while the concentration was reduced with abiotic metals As, Pb, Al and Cd. Significant increase in extracellular siderophore production was observed with Pb and Al at concentrations of 50 μM and above. The effect of metals on siderophore production was completely mitigated in presence of Fe. The results implicate effect of metals on the efficiency of siderophore production by bacteria for potential application in bioremediation of metal contaminated iron deficient soils especially in the microbial assisted phytoremediation processes.     

Antioxidant response versus selenium accumulation in the liver and kidney of the Siberian sturgeon (Acipenser baeri)

The aim of this study was to examine the effects of selenium on concentrations of metabolites and enzyme activities acting as antioxidant markers in liver and kidney of Siberian sturgeon Acipenser baeri. Sturgeons were fed selenium cysteine for 30 and 60 d at 1.25, 5, 20 mg Se kg⁻¹. Selenium level in the control feed was 0.32 mg kg⁻¹. Se concentration was measured in liver, kidney and muscle of every specimen. Sturgeon accumulated Se in tissues with a clear dose-response relationship and the highest Se concentration was recorded in liver. This outcome is lined up with the findings obtained on the antioxidant markers evaluated in both tissues, and in which a dose-response for several biomarkers was recorded in liver. The superoxide dismutase activity in Se-treated fish was generally induced, while catalase activity was lower in liver or unaltered in kidney. The concentrations of glutathione S-transferase, glutathione reductase and total glutathione responded differently for both tissues and were induced in a different way at both endpoints. No changes of glyoxalase I activity were noted for both Se-treated tissues, while for glyoxalase II enzyme in liver a dose-related pattern was found showing a reversible effect (decreased and increased counteractive response) only in the 5 mg kg⁻¹ group. Moreover, the highest Se concentrations did not cause marked changes in malondialdehyde levels of liver and kidney. The enhancement of glutathione peroxidase activity in Se-treated sturgeon might have prevented the lipid peroxidation in both tissues, providing to the Siberian sturgeon a great defense ability versus the prooxidant effect of selenium.     

Accurate sampling of PCDD/F in high temperature flue-gas using cooled sampling probes

In a laboratory-scale combustion reactor, flue-gas samples were collected at two temperatures in the post-combustion zone, 700 °C and 400 °C, using two different water-cooled sampling probes. The probes were the cooled probe described in the European Standard method EN-1948:1, referred to as the original probe, and a modified probe that contained a salt/ice mixture to assist the cooling, referred to as the sub-zero probe. To determine the efficiency of the cooling probes, internal temperature measurements were recorded at 5 cm intervals inside the probes. Flue-gas samples were analyzed for polychlorinated dibenzo-p-dioxin and dibenzofurans (PCDD/Fs). Samples collected at 700 °C using the original cooling probe showed higher concentrations of PCDD/Fs compared to samples collected using the sub-zero probe. No significant differences were observed between samples collected at 400 °C. The results indicated that artifact formation of PCDD/Fs readily occurs during flue-gas sampling at high temperatures if the cooling within the probe is insufficient, as found for the original probe at 700 °C. It was also shown that this problem could be alleviated by using probes with an enhanced cooling capacity, such as the sub-zero probe.Although this may not affect samples collected for regulatory purposes in exit gases, it is of great importance for research conducted in the high-temperature region of the post-combustion zone.     

Modes of selenium occurrence and LCD modeling of selenite desorption/adsorption in soils around the selenium-rich core,Ziyang County,China

Studying the modes of selenium occurrence in high-Se soils and its behaviors can improve understanding and evaluating its cycling, flux, and balance in geo-ecosystems and its influence on health. In this paper, using a modified sequential chemical extraction technique, seven operationally defined selenium fractions and Se valence distribution were determined about five soils in which paddy was planted (W1, W2, W3, W4, W5) and five soils in which maize was planted (H1, H2, H3, H4, H5) around the selenium-rich core, Ziyang County, Shaanxi Province, China. The results show that selenium fractions in the soils mainly include sulfide/selenide and base-soluble Se, and ligand-exchangeable Se is also high for five soils in which paddy was planted. For water-soluble Se, Se (IV) is main Se valence and almost no Se (VI) was determined about five soils in which paddy was planted, while almost 1:1 of Se (IV) and Se (VI) coexist about five soils in which maize was planted. For exchangeable Se, similar results were found. For the first time, two typical high-Se soils (W1 soil and H1 soil) were chosen to measure the pH-dependent solid-solution distribution of selenite in the pH range 3–9, and the results were explained using LCD (ligand and charge distribution) adsorption modeling. The desorbed selenite concentrations from the two soils are in general underestimated by the model due to a comparable binding affinity of phosphate and selenite on goethite and much lower amount of total selenite than total reactively adsorbed phosphate. The pH dependency of adsorption of selenite added to the soil can be successfully described with the LCD model for W1 soil. Whereas considering the influence of Al-oxides, by lowering selenite adsorption affinity constant K of Se adsorption on goethite by 16 times, the LCD model can describe the adsorption much better. The results can help to understand selenium cycling, flux, and balance in typical high-Se soils.

     

Metal stabilization mechanism of incorporating lead-bearing sludge in kaolinite-based ceramics

The feasibility and mechanism of incorporating simulated lead-laden sludge into low-cost ceramic products was investigated by observing the reaction of lead with two kaolinite-based precursors under sintering conditions. To investigate the phase transformation process of lead, lead oxide (PbO) mixed with a kaolinite or mullite precursor were fired at 500-950 °C for 3 h. Detailed X-ray diffraction analysis of sintered products revealed that both precursors had crystallochemically incorporated lead into the lead feldspar (PbAl₂Si₂O₈) crystalline structure. By mixing lead oxide with kaolinite, lead feldspar begins to crystallize at 700 °C; maximum incorporation of lead into this structure occurred at 950 °C. However, two intermediate phases, Pb₄Al₄Si₃O₁₆ and a polymorph of lead feldspar, were detected at temperatures between 700 and 900 °C. By sintering lead oxide with the mullite precursor, lead feldspar was detected at temperatures above 750 °C, and an intermediate phase of Pb₄Al₄Si₃O₁₆ was observed in the temperature range of 750-900 °C. This study compared the lead leachabilities of PbO and lead feldspar using a prolonged leaching test (at pH 2.9 for 23 d) modified from the toxicity characteristic leaching procedure. The results indicate the superiority of lead feldspar in stabilizing lead and suggest a promising and reliable strategy to stabilize lead in ceramic products.     

Relationships between hepatic trace element concentrations, reproductive status, and body condition of female greater scaup

We collected female greater scaup (Aythya marila) on the Yukon-Kuskokwim Delta, Alaska during two breeding seasons to determine if concentrations of 18 trace elements in livers and eggs were elevated and if hepatic concentrations correlated with body condition or affected reproductive status. Fifty-six percent, 5%, and 42% of females, respectively, had elevated hepatic cadmium (Cd: >3 μg g⁻¹ dry weight [dw]), mercury (Hg: >3 μg g⁻¹ dw), and selenium (Se: >10 μg g⁻¹ dw). Somatic protein and lipid reserves were not correlated with hepatic Cd or Hg, but there was a weak negative correlation between protein and Se. Hepatic Cd, Hg, and Se were similar in females that had and had not initiated egg production. In a sample of six eggs, 33% and 100%, respectively, contained Se and Hg, but concentrations were below embryotoxicity thresholds. We conclude that trace element concentrations documented likely were not adversely impacting this study population.     

Biodegradation of 4-aminobenzenesulfonate by Ralstonia sp. PBA and Hydrogenophaga sp. PBC isolated from textile wastewater treatment plant

A co-culture consisting of Hydrogenophaga sp. PBC and Ralstonia sp. PBA, isolated from textile wastewater treatment plant could tolerate up to 100 mM 4-aminobenzenesulfonate (4-ABS) and utilize it as sole carbon, nitrogen and sulfur source under aerobic condition. The biodegradation of 4-ABS resulted in the release of nitrogen and sulfur in the form of ammonium and sulfate respectively. Ninety-eight percent removal of chemical oxygen demand attributed to 20 mM of 4-ABS in cell-free supernatant could be achieved after 118 h. Effective biodegradation of 4-ABS occurred at pH ranging from 6 to 8. During batch culture with 4-ABS as sole carbon and nitrogen source, the ratio of strain PBA to PBC was dynamic and a critical concentration of strain PBA has to be reached in order to enable effective biodegradation of 4-ABS. Haldane inhibition model was used to fit the degradation rate at different initial concentrations and the parameters μ_max, K_s and K_i were determined to be 0.13 h⁻¹, 1.3 mM and 42 mM respectively. HPLC analyses revealed traced accumulation of 4-sulfocatechol and at least four unidentified metabolites during biodegradation. This is the first study to report on the characterization of 4-ABS-degrading bacterial consortium that was isolated from textile wastewater treatment plant.     

The exposition of a calcareous Mediterranean soil to toxic concentrations of Cr, Cd and Pb produces changes in the microbiota mainly related to differential metal bioavailability

The involvement of the bacterial community of an agricultural Mediterranean calcareous soil in relation to several heavy metals has been studied in microcosms under controlled laboratory conditions. Soil samples were artificially polluted with Cr(VI), Cd(II) and Pb(II) at concentrations ranging from 0.1 to 5000 mg kg⁻¹ and incubated along 28 d. The lowest concentrations with significant effects in soil respirometry were 10 mg kg⁻¹ Cr and 1000 mg kg⁻¹ Cd and Pb. However, only treatments showing more than 40% inhibition of respirometric activity led to significant changes in bacterial composition, as indicated by PCR-DGGE analyses. Presumable Cr- and Cd-resistant bacteria were detected in polluted microcosms, but development of the microbiota was severely impaired at the highest amendments of both metals. Results also showed that bioavailability is an important factor determining the impact of the heavy metals assayed, and even an inverted potential toxicity ranking could be achieved if their soluble fraction is considered instead of the total concentration. Moreover, multiresistant bacteria were isolated from Cr-polluted soil microcosms, some of them showing the capacity to reduce Cr(VI) concentrations between 26% and 84% of the initial value. Potentially useful strains for bioremediation were related to Arthrobacter crystallopoietes, Stenotrophomonas maltophilia and several species of Bacillus.     

Molecular and physiological approaches to understand the ecology of methanol degradation during the biofiltration of air streams

A 13.4 L biofilter treating an off-gas stream supplemented with methanol under two different situations was studied in terms of MeOH removal efficiency, microbial ecology and odor removal. During Period 1 (P1) the reactor was packed with wood bark chips with no pH control, treating an off-gas resulting from the aerobic chamber of a membrane biological reactor treating sewage and located outdoor, whereas during Period 2 (P2) a compressed air stream fed with MeOH was treated using PVC rings and maintaining pH at neutral values. Both systems operated at 96 g MeOH m⁻³ h⁻¹ achieving removal efficiencies of around 90% during P1 and 99.9% during P2. The relative activity of biomass developed in both systems was assessed using respirometric analysis with samples obtained from both biofilms. Higher biomass activity was obtained during P2 (0.25-0.35 kg MeOH kg⁻¹ VSS d⁻¹) whereas 1.1 kg MeOH kg⁻¹ VSS d⁻¹ was obtained in the case of P1. The application of molecular and microscopic techniques showed that the eukaryotes were predominant during P1, being the yeast Candida boidinii the most abundant microorganism. A specific Fluorescence in situ hybridization probe was designed for C. boidinii and tested successfully. As a result of the neutral pH, a clear predominance of prokaryotes was detected during P2. Interestingly, some anaerobic bacteria were detected such as Desulfovibrio, Desulfobacteraceae species and also some archaea such as Methanosarcina.     

Adsorption and breakdown of penicillin antibiotic in the presence of titanium oxide nanoparticles in water

The fate and transport of antibiotics in natural water systems is controlled in part by interactions with nanometer (10⁻⁹ m) metal oxide particles. Experiments were performed by mixing solutions of ampicillin (AMP), a common, penicillin-class human and veterinary antibiotic, with 25 nm-TiO₂ (anatase) nanoparticles at different pH conditions. Both sorption and degradation of AMP were observed in the AMP-nanoparticle solutions. For AMP concentrations from ∼3 μM to 2.9 mM the overall AMP removal from solution can be described by linear isotherms with removal coefficients (K_r) of 3028 (±267) L kg⁻¹ at pH 2, 11,533 (±823) L kg⁻¹ at pH 4, 12,712 (±672) L kg⁻¹ at pH 6, and 1941 (±342) L kg⁻¹ at pH 8. Mass spectral analysis of AMP solutions after removal of the solid nanoparticles yielded ions that indicate the presence of peniclloic acid, penilloic acid and related de-ammoniated by-products as possible compounds resulting from the degradation of AMP at the TiO₂ surface.     

Bioremediation of tributyltin contaminated sediment: degradation enhancement and improvement of bioavailability to promote treatment processes

Bioremediation of tributyltin (TBT) contaminated sediment was studied and degradation enhancement and improvement of bioavailability were also investigated. In TBT spiked sediment, the half-life of TBT in the control sample, representing natural attenuation, was 578 d indicating its persistence. In the stimulated sample (pH 7.5, aeration and incubated at 28 °C), the half-life was significantly reduced to 11 d. Further stimulation by nutrient addition (succinate, glycerol and l-arginine) or inoculation with Enterobacter cloacae (∼10⁷ viable cells g⁻¹ of sediment) resulted in half-life reduction to 9 and 10 d, respectively. In non-spiked sediment, the indigenous microorganisms were able to degrade aged TBT, but the extended period of contamination decreased the degradation efficiency. To improve bioavailability, addition of surfactant, adjustment of salinity and sonication were studied. The highest percentage solubilisation of TBT in water was obtained by adjusting salinity to 20 psu, which increased the solubility of TBT from 13% to 33%. Half-lives after bioavailability was improved were 5, 4 and 4 d for stimulation, stimulation w/nutrient addition and stimulation w/inoculation, respectively. However, natural attenuation in the control sample was not enhanced. The results show that providing suitable conditions is important in enhancing TBT biodegradation, and bioavailability improvement additionally increased the rate and degraded amount of TBT. Unfortunately, nutrient addition and inoculation of the degrader did not enhance the degradation appreciably.     

Comparison of biochar- and activated carbon-supported zerovalent iron for the removal of Se(IV) and Se(VI): influence of pH,ionic strength,and natural organic matter

Biochar (BC) and activated carbon (AC) were both produced from corn straw. Biochar-supported zerovalent iron (BC-ZVI) and activated carbon-supported zerovalent iron (AC-ZVI) were synthesized and applied for Se(IV)/Se(VI) removal. The sorption capacity of BC-ZVI for Se(IV) and Se(VI) was reported at 62.52 and 35.39 mg g^?1, higher than that of AC-ZVI (56.02 and 33.24 mg g^?1), respectively, due to its higher iron content and more positive charges. The spectroscopic analyses showed that Se(IV)/Se(VI) were reduced to Se(0)/Se(-II) of less toxicity and solubility. The effects of various factors such as pH, ionic strength, co-existing cations and anions, and natural organic matter (NOM) were also investigated. Ionic strength showed no significant effect on Se(IV)/Se(VI) removal, but pH was critical. The presence of NO₃^? and SO₄^2? did not cause obvious inhibition to the removal, while PO₄^3? inhibited the sorption capacity of BC-ZVI and AC-ZVI for Se(IV)/Se(VI) significantly. Common cations (K⁺, Ca²⁺, and Mg²⁺) were found to slightly enhance the removal, while NOM significantly decreased the sorption capacity of BC-ZVI and AC-ZVI for Se(IV)/Se(VI). Besides, NOM showed stronger inhibition effect on AC-ZVI than that on BC-ZVI. These results indicated that BC-ZVI, compared with AC-ZVI, could be a promising sorbent to remove Se(IV)/Se(VI) due to its low cost and high efficiency.

     

Arbuscular mycorrhizal fungi enhance both absorption and stabilization of Cd by Alfred stonecrop (Sedum alfredii Hance) and perennial ryegrass (Lolium perenne L.) in a Cd-contaminated acidic soil

A greenhouse pot experiment was conducted to compare the phytoextraction efficiencies of Cd by hyper-accumulating Alfred stonecrop (Sedum alfredii Hance) and fast-growing perennial ryegrass (Lolium perenne L.) from a Cd-contaminated (1.6 mg kg⁻¹) acidic soil, and their responses to the inoculations of two arbuscular mycorrhizal (AM) fungal strains, Glomus caledonium 90036 (Gc) and Glomus mosseae M47V (Gm). Ryegrass and stonecrop were harvested after growing for 9 and 27 wk, respectively. Without AM fungal inoculation, the weekly Cd extraction by stonecrop (8.0 μg pot⁻¹) was 4.3 times higher than that by ryegrass (1.5 μg pot⁻¹). Both Gc and Gm significantly increased (P < 0.05) root mycorrhizal colonization rates, soil acid phosphatase activities, and available P concentrations, and thereby plant P absorptions (except for Gm-inoculated ryegrass), shoot biomasses, and Cd absorptions (except for Gm-inoculated stonecrop), while only Gc-inoculated stonecrop significantly accelerated (P < 0.05) the phytoextraction efficiency of Cd by 78%. In addition, both Gc and Gm significantly decreased (P < 0.05) phytoavailable Cd concentrations by 21–38% via elevating soil pH. The results suggested the potential application of hyper-accumulating Alfred stonecrop associated with AM fungi (notably Gc) for both extraction and stabilization of Cd in the in situ treatment of Cd-contaminated acidic soil.