The performance of passive flow monitors and phosphate accumulating passive samplers when exposed to pulses in external water flow rate and/or external phosphate concentrations

Passive samplers are typically calibrated under constant flow and concentration conditions. This study assessed whether concentration and/or flow pulses could be integrated using a phosphate passive sampler (P-sampler). Assessment involved three 21-day experiments featuring a pulse in flow rate, a pulse of filterable reactive phosphate (FRP) concentration and a simultaneous concentration and flow pulse. FRP concentrations were also determined by parallel grab sampling and the P-sampler calibrated with passive flow monitors (PFMs) and direct measurement of flow rates. The mass lost from the PFM over the deployment periods predicted water velocity to within 5.1, 0.48 and 7.1% when exposed to a flow rate pulse (7.5-50 cm s⁻¹), concentration pulse (5-100 μg P L⁻¹), or both simultaneously. For the P-sampler, good agreement was observed between the grab and passive measurements of FRP concentration when exposed to a pulse in flow (6% overestimation) or concentration (2% underestimation).     

Performance evaluation of a tailor-made passive sampler for monitoring of tropospheric ozone

Introduction

This study presents the performance evaluation of a tailor-made passive sampler developed for the monitoring of tropospheric ozone.

Methods

The performance of the passive sampler was tested in the field conditions in terms of accuracy, precision, blank values, detection limit, effects of some parameters such as sampling site characteristics and sampling period on the field blanks, self-consistency, experimental and theoretical uptake rates, shelf life and comparison with commercial passive samplers.

Results

There was an agreement (R ²?=?0.84) between the responses of passive sampler and the continuous automatic analyser. The accuracy of the sampler, expressed as percent relative error, was obtained lower than 15%. Method precision in terms of coefficient of variance for three simultaneously applied passive samplers was 12%. Sampler detection limit was 2.42???g?m^?3 for an exposure period of 1?week, and the sampler can be stored safely for a period of up to 8?weeks before exposure. Satisfactory self-consistency results showed that extended periods gave the same integrated response as a series of short-term samplers run side by side. The uptake rate of ozone was found to be 10.21?mL?min^?1 in a very good agreement with the theoretical uptake rate (10.32?mL?min^?1). The results of the comparison study conducted against a commercially available diffusion tube (Gradko diffusion tube) showed a good linear relationship (R ²?=?0.93) between two passive samplers.

Conclusions

The sampler seems suitable to be used in large-scale measurements of ozone where no data are available or the number of existing automated monitors is not sufficient.     

Polycyclic aromatic hydrocarbons in ambient air in the Philippines derived from passive sampler with polyurethane foam disk

Passive samplers with polyurethane disks (PUF) were applied in the determination of the concentration of polycyclic aromatic hydrocarbons (PAHs) in ambient air in six residential areas in the Philippines during four simultaneous sampling periods. The uptake profiles of PAHs were determined at one site during one sampling period. Most of the PAHs that were detected in air at concentrations that were significantly higher than their analytical detection limits exhibited a linear uptake trend on the PUF disk. The linear uptake profiles of some high molecular weight (HMW) PAHs were not established and this is attributed to the low concentration of the compounds in air in the gaseous phase. The retention concentrations of phenanthrene-d-10 were determined after depuration in four sampling sites during two sampling periods. The sampling rate for phenanthrene-d-10 was calculated at the linear phase of the uptake using the k_A derived from depuration experiments and the relationship of k_A and sampling rate which was established in a previous passive sampling study. The average sampling rate obtained for phenanthrene d-10 (2.94±0.69 m³ d⁻¹) was applied for derivation of the concentrations of the PAHs in the field samples.The passive sampler with PUF disk and short integration time of 42–56 days is applicable for the derivation of the concentrations of PAHs in ambient air in the Philippines. The concentrations of the organic pollutants derived from the passive sampler showed variability for the six residential areas; reflecting the influence of possible sources of emission of the pollutants at the sites at the different sampling periods. The weather conditions, including the occurrence of a tropical cyclone, increased rainfall and high-relative humidity during the rainy season, had an influence on the concentrations of PAHs derived by the passive sampler.     

Development and calibration of a passive sampler for N-nitrosodimethylamine (NDMA) in water

N-Nitrosamines such as N-nitrosodimethylamine (NDMA) are organic compounds of environmental concern in groundwater, wastewater and potable water due to their potent carcinogenicity in laboratory animal studies and probable human carcinogenicity. While passive sampling techniques have become a widely used tool for providing time-averaged estimates of trace pollutant concentration, for chemicals such as NDMA that have relatively high water solubility, the selection of a suitable sorbent is difficult. This work is a proof of principle study that investigated for the first time the use of coconut charcoal as a passive sampler sorbent. Apparent charcoal/water sorption coefficients for NDMA were >551 mL g⁻¹ at environmentally relevant aqueous concentrations of less than 1 μg L⁻¹. Under the experimental conditions employed, a sampling rate of 0.45 L d⁻¹ was determined and for an aqueous concentration of 1000 ng L⁻¹, it is predicted that the sampler remains in the linear uptake stage for approximately 4 d, while equilibrium attainment would require about 26 d. The presence of humic acid, used as a surrogate for DOC, enhanced NDMA sorption on the coconut charcoal.     

A passive sampler for ambient gaseous oxidized mercury concentrations

This paper reports on the development of a passive sampler for estimating gaseous oxidized mercury concentrations. Atmospheric gaseous oxidized mercury concentrations calculated from passive sampler data were correlated with those obtained using an automated analyzer (r² = 0.71, p < 0.01, n = 110 for one-week deployments; r² = 0.89, p < 0.01, n = 22 for two-week deployments). Sampler uptake was not significantly affected by changes in temperature, humidity, or ozone concentration, but it was slightly dependent on wind speed. As such, an equation for correcting data due to this factor was developed based on wind tunnel and field data. The detection limit for a two-week sampler deployment was ～5 pg m^?3. Field data collected in Nevada and the southeastern United States showed these samplers are useful for investigating spatial and temporal variability in gaseous oxidized mercury concentrations.     

Observation of SO2 dry deposition velocity at a high elevation flux tower over an evergreen broadleaf forest in Central Taiwan

A 60-m flux tower was built on a 2100 m mountain for the measurement of the air pollutant concentration and the evaluation of dry deposition velocity in Central Taiwan. The tower was constructed in an evergreen broadleaf forest, which is the dominant species of forest in the world. Multiple-level SO₂ concentrations and meteorological variables at the site were measured from February to April 2008. The results showed that the mean dry deposition velocities of SO₂ were 0.61 cm s^?1 during daytime and 0.27 cm s^?1 during nighttime. From the comparison of the monthly data, a tendency was observed that the dry deposition velocity increases with LAI and solar radiation. Furthermore, it was observed that the deposition velocity was larger over wet canopy than over dry canopy, and that higher deposition velocities in the wet season were mainly caused by non-stomatal uptake of wet canopy. Over wet canopy, the mean dry deposition velocities of SO₂ were estimated to be 0.83 cm s^?1 during daytime and 0.47 cm s^?1 during nighttime; and 0.44 cm s^?1 during daytime and 0.19 cm s^?1 during nighttime over dry canopy. There is good agreement between the results of this study and those in other studies and the predictions of Zhang et al. (2003a). The medians (geometric means) of derived r_c during daytime are 233 (266) m s^?1 over dry canopy and 147 (146) m s^?1 over wet canopy. It was found that solar radiation is the critical important meteorological variable determining stomatal resistance during daytime. For non-stomatal resistance, clear dependencies were observed on the friction velocity and relative humidity.     

Ozone flux over a Norway spruce forest and correlation with net ecosystem production

Daily ozone deposition flux to a Norway spruce forest in Czech Republic was measured using the gradient method in July and August 2008. Results were in good agreement with a deposition flux model. The mean daily stomatal uptake of ozone was around 47% of total deposition. Average deposition velocity was 0.39 cm s⁻¹ and 0.36 cm s⁻¹ by the gradient method and the deposition model, respectively. Measured and modelled non-stomatal uptake was around 0.2 cm s⁻¹. In addition, net ecosystem production (NEP) was measured by using Eddy Covariance and correlations with O₃ concentrations at 15 m a.g.l., total deposition and stomatal uptake were tested. Total deposition and stomatal uptake of ozone significantly decreased NEP, especially by high intensities of solar radiation.     

Formaldehyde personal exposure measurements and time weighted exposure estimates in children

Residential concentrations of formaldehyde have been associated with poor respiratory health in children, where formaldehyde has been measured using stationary monitors inside homes. Although children spend most of their time indoors at home, there are few studies of children’s personal exposure to formaldehyde. The aim of this study was to investigate the relationship between personal exposure formaldehyde concentrations, microenvironmental concentrations and time weighted exposure estimates in children.Forty-one primary school children (aged between 9 and 12 years) wore a personal passive sampler over two 24 h periods in two seasons and completed 24 h daily activity diaries and a questionnaire about lifestyle and behaviour. Samplers were co located indoors at home, outdoors at centralised locations and indoors at school for the corresponding period.Personal exposure formaldehyde concentrations in this group of children were generally low with a geometric mean concentration of 9.1 ppb (range <detection limit to 27.3 ppb). There were strong correlations between personal exposure concentrations and both domestic indoor (r_s = .779, p < 0.001) and time weighted estimated (r_s = .802, p < 0.001) concentrations. The time weighted model did not improve the estimate of personal exposure compared with stationary indoor concentrations. Indoor air concentration measured with a single stationary monitor was a suitable surrogate for personal exposure.     

Field performance of dichotomous sequential PM air samplers

For over one year, the Environmental Protection Commission of Hillsborough County (EPCHC) in Tampa, Florida, operated two dichotomous sequential particulate matter air samplers collocated with a manual Federal Reference Method (FRM) air sampler at a waterfront site on Tampa Bay. The FRM was alternately configured as a PM_2.5, then as a PM₁₀ sampler. For the dichotomous sampler measurements, daily 24-h integrated PM_2.5 and PM_10–2.5 ambient air samples were collected at a total flow rate of 16.7 l min⁻¹. A virtual impactor split the air into flow rates of 1.67 and 15.0 l min⁻¹ onto PM_10–2.5 and PM_2.5 47-mm diameter PTFE^® filters, respectively. Between the two dichotomous air samplers, the average concentration, relative bias and relative precision were 13.3 μg m⁻³, 0.02% and 5.2% for PM_2.5 concentrations (n=282), and 12.3 μg m⁻³, 3.9% and 7.7% for PM_10–2.5 concentrations (n=282). FRM measurements were alternate day 24-h integrated PM_2.5 or PM₁₀ ambient air samples collected onto 47-mm diameter PTFE^® filters at a flow rate of 16.7 l min⁻¹. Between a dichotomous and a PM_2.5 FRM air sampler, the average concentration, relative bias and relative precision were 12.4 μg m⁻³, −5.6% and 8.2% (n=43); and between a dichotomous and a PM₁₀ FRM air sampler, the average concentration, relative bias and relative precision were 25.7 μg m⁻³, −4.0% and 5.8% (n=102). The PM_2.5 concentration measurement standard errors were 0.95, 0.79 and 1.02 μg m⁻³; for PM₁₀ the standard errors were 1.06, 1.59, and 1.70 μg m⁻³ for two dichotomous and one FRM samplers, respectively, which indicate the dichotomous samplers have superior technical merit. These results reveal the potential for the dichotomous sequential air sampler to replace the combination of the PM_2.5 and PM₁₀ FRM air samplers, offering the capability of making simultaneous, self-consistent determinations of these particulate matter fractions in a routine ambient monitoring mode.     

Dry deposition and soil-air gas exchange of polychlorinated biphenyls (PCBs) in an industrial area

Ambient air and dry deposition, and soil samples were collected at the Aliaga industrial site in Izmir, Turkey. Atmospheric total (particle + gas) ∑₄₁-PCB concentrations were higher in summer (3370 ± 1617 pg m⁻³, average + SD) than in winter (1164 ± 618 pg m⁻³), probably due to increased volatilization with temperature. Average particulate ∑₄₁-PCBs dry deposition fluxes were 349 ± 183 and 469 ± 328 ng m⁻² day⁻¹ in summer and winter, respectively. Overall average particulate deposition velocity was 5.5 ± 3.5 cm s⁻¹. The spatial distribution of ∑₄₁-PCB soil concentrations (n = 48) showed that the iron-steel plants, ship dismantling facilities, refinery and petrochemicals complex are the major sources in the area. Calculated air-soil exchange fluxes indicated that the contaminated soil is a secondary source to the atmosphere for lighter PCBs and as a sink for heavier ones. Comparable magnitude of gas exchange and dry particle deposition fluxes indicated that both mechanisms are equally important for PCB movement between air and soil in Aliaga.     

Evaluation of performance reference compounds in polyethylene-based passive air samplers

Polyethylene-based passive air samplers (PSDs) were loaded with performance reference compounds (PRCs) and deployed in a wind tunnel to examine the effects of wind speed on sampler performance. PRCs could be loaded reproducibly into PSDs, with coefficients of variation only exceeding 20% for the more volatile compounds. When PSDs were exposed to low (0.5-1.5 m s-1) and high (3.5-4.5 m s-1) wind speeds, PRC loss rate constants generally increased with increasing wind speed and decreased with increasing sampler/air partition coefficients. PSD-based air concentrations calculated using PRC loss rate constants and sampler/air partition coefficients and air concentrations measured using active samplers compared closely. PRCs can be used to account for the effect of differences in wind speeds on sampler performance and measure air concentrations with reasonable accuracy.     

Photocatalytic degradation of five sulfonylurea herbicides in aqueous semiconductor suspensions under natural sunlight

In the present study, the photocatalytic degradation of five sulfonylurea herbicides (chlorsulfuron, flazasulfuron, nicosulfuron, sulfosulfuron and triasulfuron) has been investigated in aqueous suspensions of zinc oxide (ZnO), tungsten (VI) oxide (WO₃), tin (IV) oxide (SnO₂) and zinc sulfide (ZnS) at pilot plant scale under natural sunlight. Photocatalytic experiments, especially those involving ZnO photocatalysis, showed that the addition of semiconductors in tandem with the oxidant (Na₂S₂O₈) strongly enhances the degradation rate of the herbicides in comparisons carried out with photolytic tests. The degradation of the herbicides follows a first order kinetics according to the Langmuir-Hinshelwood model. In our conditions, the amount of time required for 50% of the initial pesticide concentration to dissipate (t_½) ranged from 8 to 27 min (t_30W = 0.3-1.2 min) for sulfosulfuron and chlorsulfuron, respectively in the ZnO/Na₂S₂O₈ system. None of the studied herbicides was found after 120 min of illumination (except chlorsulfuron, 0.2 μg L⁻¹).     

Thermal removal of PCDD/Fs from medical waste incineration fly ash--effect of temperature and nitrogen flow rate

The fly ash used in this study was collected from a bag filter in a medical waste rotary kiln incineration system, using lime and activated carbon injection followed by their collection as mixed fly ash. Experiments were conducted on fly ash in a quartz tube, heated in a laboratory-scale horizontal tube furnace, in order to study the effect of temperature and nitrogen flow rate on the removal of PCDD/Fs. Results indicated that in this study PCDD/Fs in the fly ash mostly were removed and desorbed very little into the flue gas under thermal treatment especially when the heating temperature was higher than 350 °C, and dechlorination and destruction reactions took important part in the removal of PCDD/Fs. However, in terms of flow rate, when flow rate was higher than 4 cm s⁻¹, destruction efficiency of PCDD/Fs decreased dramatically and the main contributors were P₅CDF, H₆CDF and H₇CDF desorbed to flue gas, the PCDD/Fs in the fly ash decreased with enhanced flow rate.     

Nitrous oxide and methane emission from a flooded rice field as influenced by separate and combined application of herbicides bensulfuron methyl and pretilachlor

Combination of divergent active principles to achieve broad-spectrum control is gaining popularity to manage the weed menace in intensive agriculture. However, such application could have non-target impacts on the soil processes affecting soil ecology and environmental interactions. A field experiment was conducted to investigate the impact of separate and combined applications of herbicides bensulfuron methyl and pretilachlor on the emission of N₂O and CH₄, and related soil and microbial parameters in a flooded alluvial field planted to rice cv Lalat. Single application of the herbicide bensulfuron methyl or pretilachlor resulted in a significant reduction of N₂O and CH₄ emissions while the combination of these two herbicides distinctly increased N₂O and CH₄ emissions. Cumulative N₂O emissions (kg N₂O-N) followed the order of bensulfuron methyl (0.35 kg ha⁻¹) < pretilachlor (0.36 kg ha⁻¹) < control (0.45 kg ha⁻¹) < bensulfuron methyl 0.6% + pretilachlor 6.0% single dose (0.49 kg ha⁻¹) < bensulfuron methyl 0.6% + pretilachlor 6.0% double dose (0.54 kg ha⁻¹). Cumulative CH₄ emissions (kg CH₄), on the other hand, followed the order of bensulfuron methyl (47.89 kg ha⁻¹) < pretilachlor (73.17 kg ha⁻¹) < bensulfuron methyl 0.6% + pretilachlor 6.0% single dose (93.50 kg ha⁻¹) < control (106.54 kg ha⁻¹) < bensulfuron methyl 0.6% + pretilachlor 6.0% double dose (124.67 kg ha⁻¹). The inhibitory effect of separate application of herbicides bensulfuron methyl 0.6% and pretilachlor 6.0% on N₂O emission was linked to lower mineral N, lower denitrifying and nitrifying activity and low denitrifier and nitrifier populations. Inhibitory effect on CH₄ emission, on the contrary, was linked to prevention in the drop of redox potential, lower readily mineralizable carbon (RMC) and microbial biomass carbon (MBC) contents as well as lower methanogenic and higher methanotrophic bacterial population. Admittedly, stimulatory effect of combined application of herbicides bensulfuron methyl 0.6% and pretilachlor 6.0% at double dose on N₂O and CH₄ emission was related to reversal of the identified indicators of inhibition. Results indicate that while individual application of herbicides bensulfuron methyl 0.6% or pretilachlor 6.0% can reduce N₂O and CH₄ emission from flooded soil planted to rice, their combined application at normal dose can keep the emission at a comparatively lower level with significantly higher grain yield as compared to the herbicides applied alone.     

Passive air monitoring of PCBs and PCNs across East Asia: a comprehensive congener evaluation for source characterization

A comprehensive congener specific evaluation of polychlorinated biphenyls (PCBs) and polychlorinated naphthalenes (PCNs) in the atmosphere was conducted across East Asia in spring 2008, applying polyurethane foam (PUF) disk passive air sampler (PAS) as monitoring device. Mean concentrations derived for Japan, China and Korea were 184 ± 24, 1100 ± 118, and 156 ± 20 pg m⁻³ for ∑₂₀₂ PCBs, and 9.5 ± 1.5, 61 ± 6, and 16 ± 2.4 pg m⁻³ for ∑₆₃ PCNs, respectively. Relative to reported data from 2004, the present results suggest that air PCBs concentrations have not changed much in Japan and Korea, while it has increased by one order of magnitude in China. From principal component analysis, combustion emerged highly culpable in contemporary emissions of both PCBs and PCNs across the East Asian sub-region. Another factor derived as important to air PCBs was re-emissions/volatilization. Signals from PCBs formulations were also picked, but their general importance was virtually consigned to the re-emissions/volatilization tendencies. On the contrary, counterpart PCNs formulations did not appear to contribute much to air PCNs.     

Computational fluid dynamic modeling of two passive samplers

To effectively use a passive sampler for monitoring trace contaminants in the gas-phase, its sampling characteristics as a function of ambient wind conditions must be known. In this study two commonly used passive samplers were evaluated using computational fluid dynamics. Contaminant uptake by the polyurethane foam (PUF) was modeled using a species transport model. The external-internal flow interactions in the sampler were characterized, and the uptake rates of contaminant species were quantified. The simulations show that flow fields in the samplers have strong velocity gradients, and single-point velocity measurements do not capture flow interactions accurately. Sampling rates calculated for a PUF in freestream are in good agreement with sampling rates for PUFs in the passive samplers studied for the same average velocity over the PUF. The calculated sampling rates are in general agreement with those obtained experimentally by other researchers.     

Ozonation of azo dye Acid Red 14 in a microporous tube-in-tube microchannel reactor: decolorization and mechanism

Despite the great success of time-weighted average passive sampling of hydrophobic contaminants, such as PCBs and PAHs, the sampling of polar organic compounds still presents a challenge because the equilibrium between water and most sampling phases is attained in a relatively short time. In this study, we proposed a new time-integrative sampler using in situ solvent extraction (TISIS) for polar organic chemicals. The sampler was composed of a 15 cm poly(dimethylsiloxane) (PDMS) tubing, with an internal diameter of 0.5 mm and wall thickness of 0.5 mm, through which an extraction solvent (acetonitrile) was passed. Four polar organic contaminants, caffeine, atrazine, diuron and 17α-ethynylestradiol, were chosen for the evaluation of the performance of the sampler. Without the use of in situ solvent extraction, the PDMS tubing when exposed to a constant aqueous concentration of the four model compounds was able to linearly accumulate those compounds for less than 12 h and equilibrium between the PDMS tubing and water was attained in 2 d under our laboratory conditions. However, TISIS when exposed to a constant aqueous concentration was able to linearly accumulate all the model compounds without any exposure time limitation. The measured sampling rates at three different extraction flow rates (0.2, 0.5, 1.5 mL min⁻¹) were similar, regardless of the chemicals, indicating that the overall mass transfer from aqueous solution to the extraction solvent was most likely dominated by partitioning to the PDMS tubing and the internal diffusion within PDMS. In addition, a pulsed exposure experiment confirmed that TISIS operated in a time-integrative mode when the environmental concentration was highly fluctuated.     

A review of current knowledge concerning dry deposition of atmospheric mercury

The status of the current knowledge concerning the dry deposition of atmospheric mercury, including elemental gaseous mercury (Hg⁰), reactive gaseous mercury (RGM), and particulate mercury (Hg_p), is reviewed. The air–surface exchange of Hg⁰ is commonly bi-directional, with daytime emission and nighttime deposition over non-vegetated surfaces and vegetated surfaces with small leaf area indices under low ambient Hg⁰ conditions. However, daytime deposition has also been observed, especially when the ambient Hg⁰ is high. Typical dry deposition velocities (V_d) for Hg⁰ are in the range of 0.1–0.4 cm s^?1 over vegetated surfaces and wetlands, but substantially smaller over non-vegetated surfaces and soils below canopies. Meteorological, biological, and soil conditions, as well as the ambient Hg⁰ concentrations all play important roles in the diurnal and seasonal variations of Hg⁰ air–surface exchange processes. Measurements of RGM deposition are limited and are known to have large uncertainties. Nevertheless, all of the measurements suggest that RGM can deposit very quickly onto any type of surface, with its V_d ranging from 0.5 to 6 cm s^?1. The very limited data for Hg_p suggest that its V_d values are in the range of 0.02–2 cm s^?1.A resistance approach is commonly used in mercury transport models to estimate V_d for RGM and Hg_p; however, there is a wide range of complexities in the dry deposition scheme of Hg⁰. Although resistance-approach based dry deposition schemes seem to be able to produce the typical V_d values for RGM and Hg⁰ over different surface types, more sophisticated air–surface exchange models have been developed to handle the bi-directional exchange processes. Both existing and newly developed dry deposition schemes need further evaluation using field measurements and intercomparisons within different modelling frameworks.     

Suitability of passive sampling for the monitoring of pharmaceuticals in Finnish surface waters

The occurrence of five pharmaceuticals, consisting of four anti-inflammatory and one antiepileptic drug, was studied by passive sampling and grab sampling in northern Lake Päijänne and River Vantaa. The passive sampling was performed by using Chemcatcher® sampler with a SDB-RPS Empore disk as a receiving phase. In Lake Päijänne, the sampling was conducted during summer 2013 at four locations near the discharge point of a wastewater treatment plant and in the years 2013 and 2015 at four locations along River Vantaa. The samples were analyzed by liquid chromatography coupled to tandem mass spectrometry (LC-MS/MS) in the multiple reaction monitoring mode. The concentrations of carbamazepine, diclofenac, ibuprofen, ketoprofen, and naproxen in Lake Päijänne determined by passive sampling ranged between 1.4–2.9 ng L^?1, 15–35 ng L^?1, 13–31 ng L^?1, 16–27 ng L^?1, and 3.3–32 ng L^?1, respectively. Similarly, the results in River Vantaa ranged between 1.2–40 ng L^?1, 15–65 ng L^?1, 13–33 ng L^?1, 16–31 ng L^?1, and 3.3–6.4 ng L^?1. The results suggest that the Chemcatcher passive samplers are suitable for detecting pharmaceuticals in lake and river waters.