用硫铁矿处理含汞废水的试验研究

对硫铁矿处理含汞废水进行了试验研究。探索了硫铁矿用量及细度、混合反应时间、废水ｐＨ等因素对除汞效果的影响，结果表明，废水ｐＨ２．５－９．５、Ｈｇ＾２＋１０－２５０ｍｇ／Ｌ，按汞／硫铁矿为１／１０００（重量）加入硫铁矿，汞的去除率达９９％以上，出水ｐＨ接近中性。该方法简便、经济、实用，有较好的处理效果。     

流态化电极电解法处理含氰废水

采用细粒膨胀石墨流态化阳极电解法处理含氰量为８０－９０ｍｇ／Ｌ的废水，试验选择出的处理条件为：ｐＨ９－１０，废水流速４２－４５Ｌ／ｈ，槽电流２－３Ａ，ＮａＣｌ加入量１．５－３．０ｇ／Ｌ。同样条件下，使用细粒膨胀石墨流态化电极的电解除氰效果较用简形板状电极好。     

酸洗废液非氯氧化法生产三氯化铁工业试验

介绍了用酸洗液非氯氧化法制三氯化铁的工业试验情况，讨论了影响反应的主要因素，选择出的反应条件为：反应温度６０－７５℃；反应压力１００－２００Ｐａ表；反应时间３．０－３．５ｈ。在此条件下，Ｆｅ＾２＋的转化率在９０％以上。     

废铁屑—H2O2法处理炼油厂含酚废水

用废铁屑作催化剂，Ｈ２Ｏ２作氧化剂，对炼厂汽提后含硫废水进行了除酚试验研究，考察了初始ＰＨ、Ｈ２Ｏ２投加量、废铁屑投加量对酚去除率的影响。对含酚量为３３１．５ｍｇ／Ｌ的废水，将其初始ＰＨ调至７．２，３０％Ｈ２Ｏ２的投加量为７．５ｍＬ／Ｌ，废铁屑的投加量为３－８ｇ／Ｌ，经２ｈ反应后，酚的脱除率可达９９．９％。     

煤气洗涤废水的处理

采用硫酸亚铁沉淀－沉渣回流－次氯酸钠氯化工艺处理ＣＮ＾－含量为４ｍｇ／Ｌ、Ｓ＾２－含量为６ｍｇ／Ｌ的煤气洗涤废水，ＣＮ＾－的去除率可达９５％以上，Ｓ＾２－的去除率近１００％。     

光度法测定大气中的己二胺

研究了用蒸馏水为吸收液采样、用２，４－二硝基氯苯光度法测定大气中己二胺的浓度。通过试验，确定了采样方法、显色剂和Ｎａ２ＣＯ３溶液用量、反应液ｐＨ、显色反应温度和时间、萃取时间等；得出大气中己二胺的最低检出浓度为０．４μｇ／ｍ３，吸收液平行测定的相对标准偏差为２．１％，加标回收率为９２％￣９４％。     

废水中铁和锑同时的动力学—停流光度法

依据诱导反应的原理，提出了一种多元素同时测定的方法。用停流技术研究了Ｆｅ＾２＋和Ｓｂ＾３＋诱导的Ｃｒ＾６＋－Ｉ＾－氧化还原反应动力学，建立了同时测微量铁和锑的条件。线性工作分别为０－２．２μｇ／ｍｌ Ｆｅ＾２＋和０－２．０μｇ／ｍｌ Ｓｂ＾３＋，检测限为０．０１２μｇ／ｍｌＦｅ＾２＋和０．０１４μｇ／ｍＬＳｂ＾３＋，测定了废水中铁和锑的含量。     

新型高效分散阻垢剂XH-929的性能及应用

分散阻垢剂ＸＨ－９２９对循环冷却水中ＣａＣＯ３、Ｆｅ２Ｏ３、ＭｇＳｉＯ３、Ｃａ３（ＰＯ４）２的沉积结垢有很好的抑制作用,且能在碱性条件下稳定Ｚｎ２＋。动态模拟试验和工业应用实例表明,ＸＨ－９２９分散阻垢剂与适量缓蚀剂复配后,可起到较好的阻垢、缓蚀作用。     

磁化水抑垢的研究

通过静态试验研究了Ｃａ＾２＋、Ｍｇ＾２＋的总浓度、碱度、ＰＨ、ＳＯ＾２－４对磁水抑垢效果的影响,得出了应用磁化水抑垢的适宜条件,为磁水器的实际应用提供了依据。     

化肥厂含氮废水的生物硝化处理试验

用维纶软性纤维作填料，进行了生物膜法三级硝化处理化肥厂含氮废水的试验，ＴＫＮ的去除负荷最高可达０．３７７ｋｇ／ｍ＾３．ｄ，总硝化率可达９３％。三级硝化后，出水中Ｕｒｅａ－Ｎ〈３ｍｇ／Ｌ、ＮＨ３－Ｎ〈１７ｍｇ／Ｌ。若投加痕量Ｍｇ＾２（５０μｇ／Ｌ）可以促进尿素的水解 。     

复合载体对选择性催化还原催化剂低温脱硝性能的影响

采用浆液浸涂法在堇青石蜂窝陶瓷载体上涂覆Al2O_3-TiO_2-ZSM-5分子筛复合载体,并通过浸渍法负载活性组分Mn-Fe-Ce,制备了M/ATZ-CC选择性催化还原催化剂。考察了催化剂的低温脱硝活性和抗水性能,表征了催化剂的物性参数和氨-程序升温脱附性能。实验结果表明,M/ATZ-CC催化剂具有优异的脱硝活性和抗水性能,在反应温度为160℃、水蒸气加入量为10%(φ)、NO体积分数为0.1%、n(NH_3)∶n(NO)=1、O_2体积分数为3.0%、体积空速为3 000~10 000 h~(-1)的条件下,NO去除率在80%以上。表征结果显示,该催化剂的比表面积、孔径、弱酸酸量、中强酸酸量和总酸量得到了显著提高。     

Extraction of heavy metal ions from waste colored glass through phase separation

A new method utilizing phase separation phenomena for the extraction of heavy metal ions used as colorants in colored glass is proposed. Colored soda-lime-silica glass containing Co or Cr as a colorant was remelted with B2O3 to yield soda-lime-borosilicate glass. The soda-lime-borosilicate glass thus obtained was leached in 1M nitric acid at 90 degrees C to dissolve the borate phase. All cations (Na, Ca, Cr and Co) concentrated in the borate phase are successfully leached out with the dissolution of the borate phase, when the amount of the B2O3 added to the glass and heat treatment conditions are properly chosen. Porous silicate glass powders with high SiO2 purity are obtained as the result of the leaching. Porous glass can also be formed as bulk material by controlling the composition of additives during the remelting.     

Characterization and leaching of NiCd and NiMH spent batteries for the recovery of metals

Since NiMH and NiCd batteries are still used in the electronic devices market, a treatment and recycling plant has many advantages both from the environmental and the economic points of view. Unfortunately, there is no relationship between shape, size and chemical composition of spent batteries, consequently the characterization and the leaching method of the starting material becomes an important step of the overall treatment process in choosing the best conditions for the selective separation of the metals by hydrometallurgy. Leaching at 20 degrees C with H(2)SO(4) 2M for about 2h seems to be a good solution in terms of cost and efficiency for both battery types. The hydroxide compounds can be readily leached while Ni present as metallic form requires more aggressive conditions due to kinetic constraints. In this paper, the characterization of NiMH and NiCd spent batteries and the results of leaching tests in different conditions are reported.     

An advanced study on the hydrometallurgical processing of waste computer printed circuit boards to extract their valuable content of metals

This study refers to two chemical leaching systems for the base and precious metals extraction from waste printed circuit boards (WPCBs); sulfuric acid with hydrogen peroxide have been used for the first group of metals, meantime thiourea with the ferric ion in sulfuric acid medium were employed for the second one. The cementation process with zinc, copper and iron metal powders was attempted for solutions purification. The effects of hydrogen peroxide volume in rapport with sulfuric acid concentration and temperature were evaluated for oxidative leaching process. 2 M H₂SO₄ (98% w/v), 5% H₂O_2, 25 °C, 1/10 S/L ratio and 200 rpm were founded as optimal conditions for Cu extraction. Thiourea acid leaching process, performed on the solid filtrate obtained after three oxidative leaching steps, was carried out with 20 g/L of CS(NH₂)₂, 6 g/L of Fe³⁺, 0.5 M H₂SO₄, The cross-leaching method was applied by reusing of thiourea liquid suspension and immersing 5 g/L of this reagent for each other experiment material of leaching. This procedure has lead to the doubling and, respectively, tripling, of gold and silver concentrations into solution. These results reveal a very efficient, promising and environmental friendly method for WPCBs processing.     

Comparative degradation between heavy and light crude oil mediated by nitrogen‐induced cell‐surface hydrophobicity

A bacterial strain UKMP‐10M2 isolated from a Malaysian petroleum refinery was able to degrade 84% of heavy Khafji sour crude and 68% of light Tapis sweet crude within seven days. Analysis of gas chromatography‐flame ionization detector chromatograms show the strain UKMP‐10M2 degraded up to 90% pristane and 50% phytane in heavy crude, but significantly lower pristane (50%) and phytane (30%) were degraded from the light crude. A mixture of aliphatic hexadecane and three‐ring phenanthrene better supported the growth of isolate UKMP‐10M2 compared to using phenanthrene alone, suggesting cometabolism influenced how crude oil with different individual hydrocarbon contents affected the degradation. Peptone as the source of nitrogen increases the emulsifying index in UKMP‐10M2 exposed to heavy Khafji sour crude 20% higher than in light Tapis sweet crude. However, BATH assay showed the same nitrogen source increases bacterial cell surface hydrophobicity of UKMP‐10M2 up to 14% higher in light Tapis crude oil compared to heavy Khafji. This study suggest the nitrogen source plays a decisive role in elevating UKMP‐10M2 bacterial cells hydrophobicity, and in correlation with types of crude oil. Phylogenetic tree analysis based on 16S rDNA sequence results identified the strain to be Rhodococcus ruber.     

石墨相氮化碳协同UV-H_2O_2光催化降解亚甲基蓝

以三聚氰胺为前驱体,经热解—回流法制备了石墨相氮化碳(g-C3N4),采用XRD、FTIR、SEM、EDS、PL等技术对g-C_3N_4进行了表征。研究了g-C_3N_4在UV-H_2O_2体系中对废水中亚甲基蓝(MB)的光降解效果。实验结果表明,UV+g-C_3N_4催化剂+H_2O_2体系能协同降解MB,在初始MB质量浓度为20 mg/L、初始废水p H为5、废水体积为250 mL、g-C_3N_4加入量为0.10 g、H_2O_2浓度为0.4 mmol/L、反应温度为25℃的优化工艺条件下,紫外光照射70 min时MB脱色率达98.32%。g-C_3N_4催化剂具有较好的重复使用性能,使用5次后MB脱色率仍保持在95.10%。     

3M测试片法在膜法水处理技术中的应用

采用3M测试片法测定膜法水处理系统的细菌总数,找出双膜系统的微生物污染环节,并采用正交实验筛选出适宜的杀菌剂种类、杀菌剂加入量和杀菌时间。实验结果表明：3M测试片法的测定结果数据准确可靠,且操作简便,节省时间,可以替代常规的平皿培养法用于评价膜的微生物污染情况;某炼化公司双膜系统的反渗透膜已受到微生物的污染,确定的适宜杀菌条件为杀菌剂Trsea 380、杀菌剂加入量50 mg/L、杀菌时间2.0 h,在此条件下杀菌率可达100%。     

Effects of Storage Time on Properties of Soybean Protein-Based Plastics

Soybean protein has been considered as a potential biodegradable polymer in the manufacture of plastics. The purpose of this investigation was to characterize the effect of storage time on thermal and mechanical properties of soybean protein isolate (SPI) plastics. SPI was separated from defatted soy flour, modified with 1M or 2M urea, or plasticized with glycerol, and compression molded into plastics. Plastic made from SPI alone was used as a control. For all SPI plastics, glass transition temperatures and dynamic storage modulus increased and loss tangent decreased during storage. Excess enthalpy of relaxation of all SPI plastics had an exponential relationship with storage time, indicating a fast aging rate at the beginning of storage. All SPI plastics tended to be stiff and brittle during storage. The plastics with glycerol had the slowest aging rate and were fairly stable after 60 days, with about 8.8 MPa tensile strength and 168% strain at break. Plastics with the 2M urea-modification SPI also had a slow aging rate and became relative stable after 60 days, with about 10 MPa tensile strength and 72% elongation.     

Characterization of trace elements in chicken and duck litter ash

For safe and sustainable management of poultry litter, it is important to evaluate and understand the chemical forms and concentrations of their constituent trace elements during treatment for disposal. This experiment was carried out to compare changes in metal (Cu, Mn, Zn, Pb and Ni) fractions in chicken and duck litter after incineration at temperatures ranging from 200 to 900 degrees C. The metals were stepwise fractionated into exchangeable, adsorbed, organically bound, carbonate precipitated and residual forms by extracting with 0.5M KNO3, de-ionized water, 0.5M NaOH, 0.05M Na2 EDTA and 4M HNO3, respectively. The content of total metal and other elements (i.e., Ca, Mg and K) were was also determined. Results showed an increasing trend in the total concentrations of metals with increasing temperature with higher amounts in chicken litter ash (CLA) than duck litter ash (DLA). Higher temperatures significantly reduced the levels of H2O-soluble Mn, Zn and Ni and enhanced those of Cu and Pb. The metal fractions extracted by EDTA and HNO3 increased directly with increasing temperature while the fraction extracted with KNO3 and NaOH decreased with ashing. For Cu, Mn, Pb and Ni, the amount extracted varied in the order EDTA>HNO3>NaOH>KNO3>H2O, but the absolute amounts differed between CLA and DLA. Peak concentrations of the total metals were achieved at the highest burning temperature. The amount of H2O soluble Ca and Mg decreased and K increased in both CLA and DLA with temperature. Total and exchangeable forms of cations increased with increasing temperature. Total Ca was highest in DLA, whereas total Mg and K were higher in CLA. This study indicated that incinerating poultry litter before soil application may have mixed effects on the vulnerable metal fractions by increasing or decreasing some fractions, depending on poultry type.     

Evaluation of gold and silver leaching from printed circuit board of cellphones

Electronic waste has been increasing proportionally with the technology. So, nowadays, it is necessary to consider the useful life, recycling, and final disposal of these equipment. Metals, such as Au, Ag, Cu, Sn and Ni can be found in the printed circuit boards (PCB). According to this, the aims of this work is to characterize the PCBs of mobile phones with aqua regia; obtaining “reference” values of leaching, to gold and silver, with cyanide and nitric acid, respectively; and study the process of leaching of these metals in alternative leaching with sodium thiosulfate and ammonium thiosulfate. The metals were characterized by digesting the sample with aqua regia for 1 and 2 h at 60 °C and 80 °C. The leaching of Au with a commercial reagent (cyanide) and the Ag with HNO₃were made. The leaching of Au and Ag with alternative reagents: Na₂S₂O_3, and (NH₄)₂S₂O₃ in 0.1 M concentration with the addition of CuSO₄, NH₄OH, and H₂O₂, was also studied. The results show that the digestion with aqua regia was efficient to characterize the metals present in the PCBs of mobile phones. However, the best method to solubilize silver was by digesting the sample with nitric acid. The leaching process using sodium thiosulfate was more efficient when an additional concentration of 0.015 and 0.030 M of the CuSO₄ was added.