Enhanced adsorption of phosphate by loading nanosized ferric oxyhydroxide on anion resin

Ferric oxyhydroxide loaded anion exchanger （FOAE） hybrid adsorbent was prepared by loading nanosized ferric oxyhydroxide （FO） on anion exchanger resin for the removal of phosphate from wastewater. TEM and XRD analysis confirmed the existence of FO on FOAE. After FO loading, the adsorption capacity of the hybrid adsorbent increased from 38.70 to 51.52mg.g-1. Adsorption processes for both FOAE and anion resin were better fit to the pseudo first order model. Batch adsorption experiments revealed that higher temperature （313K）, higher initial phosphate concentration （50 mg.L-1） and lower solution pH （pH value of 2） would be more propitious to phosphate adsorption. Competition effect of coexisting anions on phosphate removal can be concluded as sulfate 〉 nitrate 〉 chloride. Freundlich isotherm model can describe the adsorption of phosphate on FOAE more accurately, which indicated the heterogeneous adsorption occurred on the inner-surface of FOAE.     

Experimental and DFT insights into nitrogen and sulfur co-doped carbon nanotubes for effective desulfurization of liquid phases: Equilibrium & kinetic study

• Synthesis of NS-CNTS is used in a high desulfurization performance. • Synthesizing NS-CNT is considered as a novel adsorbent from low-cost precursors. • A high sulfur removal capacity for NS-CNT is attained compared with recent works. Herein, nitrogen and sulfur co-doped carbon nanotubes (NS-CNT) adsorbents were synthesized via the chemical vapor deposition technique at 1000°C by employing the camphor, urea and sulfur trioxide pyridine. In this study, desulfurization of two types of mercaptans (dibenzothiophene (DBT) and tertiary butyl mercaptan (TBM) as nonlinear and linear forms of mercaptan) was studied. In this regard, a maximum capacity of NS-CNT was obtained as 106.9 and 79.4 mg/g and also the removal efficiencies of 98.6% and 88.3% were achieved after 4 h at 298K and 0.9 g of NS-CNT for DBT and TBM, respectively. Characterization of the NS-CNTs was carried out through exploiting scanning electron microscopy (SEM), X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FTIR), and elemental analysis (CHN). The isotherm equilibrium data could be ascribed to the Freundlich nonlinear regression form and the kinetic data was fitted by nonlinear form of the pseudo second order model. The negative values of ΔS⁰, ΔH⁰ and ΔG⁰ specify that the adsorption of both types of mercaptans was a natural exothermic process with a reduced entropy. Maintenance of more than 96% of the adsorption capacity even after nine cycles suggest the NS-CNT as a superior adsorbent for mercaptans removal in the industry. Density functional theory (DFT) calculations were also performed to peruse the effects of S/N co-doping and carbon monovacancy defects in CNTs toward the adsorption of DBT and TBM.     

Adsorption property of direct fast black onto acid-thermal modified sepiolite and optimization of adsorption conditions using Box-Behnken response surface methodology

The adsorption of direct fast black onto acid-thermal modified sepiolite was investigated. Batch adsorption experiments were performed to evaluate the influences of experimental parameters such as initial dye concentration, initial solution pH and adsorbent dosage on the adsorption process. The three-factor and three-level Box-Behnken response surface methodology (RSM) was utilized for modeling and optimization of the adsorption conditions for direct fast black onto the acid-thermal modified sepiolite. The raw sepiolite was converted to acid-thermal modified sepiolite, and changes in the fourier transform infrared spectrum (FTIR) adsorption bands of the sample were noted at 3435 cm^-1 and 1427 cm^-1. The zeolitic water disappeared and the purity of sepiolite was improved by acid-thermal modification. The decolorization rate of direct fast black adsorbed increased from 68.2% to 98.9% on acid-thermal modified sepiolite as the initial solution pH decreased from 10 to 2. When the adsorbent dosage reached to 2.5 g·L^-1, 2.0 g·L^-1, 1.5 g·L^-1 and 1.0 g·L^-1, the decolorization rate was 90.3%, 86.7%, 61.0% and 29.8%, respectively. When initial dye concentration increased from 25 to 200 mg·L^-1, the decolorization rate decreased from 91.9% to 60.0%. The RSM results showed that the interaction between adsorbent dosage and pH to be a significant factor. The optimum conditions were as follows: the adsorbent dosage 1.99 g·L^-1, pH 4.22, and reaction time 5.2 h. Under these conditions, the decolorization rate was 95.1%. The three dimensional fluorescence spectra of direct fast black before and after treatment showed that the direct fast black was almost all adsorbed by the acid-thermal modified sepiolite.     

Preparation of a novel anion exchange group modified hyper-crosslinked resin for the effective adsorption of both tetracycline and humic acid

A novel hyper-crosslinked resin (MENQ) modified with an anion exchange group was prepared using divinylbenzene (DVB) and methyl acrylate (MA) as comonomers via four steps: suspension polymerization, post-crosslinking, ammonolysis and alkylation reactions. The obtained resin had both a high specific surface area (793.34 m²·g^-1) and a large exchange capacity (strong base anion exchange capacity, SEC: 0.74 mmol·g^-1, weak base anion exchange capacity, WEC: 0.45 mmol·g^-1). XAD-4 was selected as an adsorbent for comparison to investigate the adsorption behavior of tetracycline (TC) and humic acid (HA) onto the adsorbents. The results revealed that MENQ could effectively remove both TC and HA. The adsorption capacity of XAD-4 for TC was similar to that of MENQ, but XAD-4 exhibited poor performance for the adsorption of HA. The adsorption isotherms of TC and HA were well-fitted with the Freundlich model, which indicated the existence of heterogeneous adsorption through cation-π bonding and π–π interactions. The optimal solution condition for the adsorption of TC was at a pH of 5–6, whereas the adsorption of HA was enhanced with increasing pH of the solution.     

Mass-transfer processes of chromium(VI) adsorption onto guava seeds

The chromium(VI) biosorption onto guava seeds, as an alternative method for Cr⁶⁺ removal from aqueous solutions, was investigated. The parameters affecting kinetics and equilibrium of Cr⁶⁺ adsorption onto guava seeds were studied. An external mass-transfer diffusion coefficient k and intra-particle diffusion coefficient k_i were determined to measure the rate-limiting step of adsorption. A single external mass-transfer diffusion model and intra-particle diffusion models were used. The effects of initial pH, sorbent mass, and initial Cr⁶⁺ concentrations on mass-transfer coefficients were investigated. The external mass-transfer coefficient has an average value of 7.2×10^-3 cm s^-1, while the intra-particle mass-transfer diffusion coefficient was 0.34 mg g^-1 min^-0.5. This indicates that external diffusion to the guava seeds surface and intra-particle diffusion are both involved in the sorption process. The isotherm equilibrium data were well fitted by the Langmuir and Freundlich models with an average correlation coefficient R²=0.98. The maximum removal of Cr⁶⁺ was obtained at pH 1 (about 100% for adsorbent dose of 15 g l^-1 and 25 mg l^-1 initial concentration of Cr⁶⁺). The results indicated that the guava seeds exhibit acceptable sorption capacity.     

Removal of toxic chromium(VI) from aqueous solution by activated carbon using Casuarina equisetifolia

Highly activated carbon from the seed husk of Casuarina Casuarinas equisetifolia, a worldwide famous plant, have been prepared and tested for the removal of toxic Cr(VI) from its aqueous solution. The adsorbent was investigated for influences of initial chromium concentration (75, 100, 125, and 150 mg l^-1), pH, contact time, and quantity of carbon on removal of Cr(VI) from aqueous solution at room temperature (25±2 °C). The adsorption kinetic of Cr(VI) was studied, and the rates of sorption were found to conform to pseudo-second-order kinetics with a good correlation (R²≥0.99). The Langmuir and Freundlich models fit the isotherm data well. Furthermore, the Gibbs free energy was obtained for each system and was found to be-5.29 kJ mol^-1 for removal of Cr(IV). The negative value of Δ G° indicates the feasibility and spontaneous nature of adsorption. The results indicate that acidic pH (1.05) supported the adsorption of Cr(IV) on activated carbon. The maximum adsorption capacity of Cr(VI) on activated carbon was about 172.4 mg g^-1 at pH 1.05.     

Simple fabrication of carboxymethyl cellulose and κ-carrageenan composite aerogel with efficient performance in removal of fluoroquinolone antibiotics from water

● A composite aerogel was simply obtained to remove various fluoroquinolones (FQs). ● The structural and textural properties of this composite aerogel are improved. ● Its adsorption capacity was improved at a low content of coexisting Cu²⁺ or Fe³⁺ ion. ● Two substructural analogs of FQs are compared to explore the adsorption mechanisms. ● This aerogel after saturated adsorption can be reused directly for Cu²⁺ adsorption. 3D composite aerogels (CMC-CG) composed of carboxymethyl cellulose and κ-carrageenan were designed and fabricated using the one-pot synthesis technique. The optimized CMC-CG showed a good mechanical property and a high swelling ratio due to its superior textural properties with a proper chemically cross-linked interpenetrating network structure. CMC-CG was utilized for the removal of various fluoroquinolones (FQs) from water and exhibited high adsorption performance because of effective electrostatic attraction and hydrogen bonding interactions. Ciprofloxacin (CIP), a popular FQ, was used as the representative. The optimized CMC-CG had a theoretically maximal CIP uptake of approximately 1.271 mmol/g at the pH of 5.0. The adsorption capacity of CMC-CG was improved in the presence of some cations, Cu²⁺ and Fe³⁺ ions, at a low concentration through the bridging effect but was reduced at a high concentration. The investigation of adsorption mechanisms, based on the adsorption kinetics, isotherms and thermodynamic study, Fourier transform infrared spectrometry and X-ray photoelectron spectroscopy analyses before and after adsorption, and changes in the adsorption performance of CMC-CG toward two molecular probes, further indicated that electrostatic attraction was the dominant interaction rather than hydrogen bonding in this adsorption. CMC-CG after saturated adsorption of CIP could be easily regenerated using a dilute NaCl aqueous solution and reused efficiently. Moreover, the disused aerogel could still be reused as a new adsorbent for effective adsorption of Cu²⁺ ion. Overall, this study suggested the promising applications of this composite aerogel as an eco-friendly, cost-effective, and recyclable adsorbent for the efficient removal of FQs from water.     

富磷污泥生物炭去除水中Pb(Ⅱ)的特性研究

以城市污水厂富磷剩余污泥为研究对象,考察高温热解制备生物炭吸附剂对水中Pb(Ⅱ)的去除效果.研究表明,随着热解温度升高,制备的生物炭对Pb(Ⅱ)的吸附能力增强;在相同热解温度下,生污泥生物炭对Pb(Ⅱ)的吸附能力比消化污泥生物炭大.采用700℃热解1 h制备生污泥生物炭以研究对Pb(Ⅱ)吸附的影响因素,结果显示:吸附180 min达到吸附平衡;富磷污泥生物炭对Pb(Ⅱ)的去除率随pH增加而升高;生物炭投加量增加,对Pb(Ⅱ)去除率上升,而单位吸附容量迅速减小.污泥生物炭对Pb(Ⅱ)的吸附符合准二级反应动力学,Langmuir模型比Freundlich模型能更好地拟合等温吸附线.在pH 5.0、吸附时间3 h、生物炭投加量20 g.L-1条件下,对Pb(Ⅱ)的最大吸附量为34.5 mg.g-1,表明富磷污泥生物炭可以作为一种廉价的吸附剂.     

Validation of polymer-based nano-iron oxide in further phosphorus removal from bioeffluent: laboratory and scaledup study

The efficient removal of phosphorous from water is an important but challenging task. In this study, we validated the applicability of a new commercially available nanocomposite adsorbent, i.e., a polymer-based hydrated ferric oxide nanocomposite (HFO-201), for the further removal of phosphorous from the bioeffluent discharged from a municipal wastewater treatment plant, and the operating parameters such as the flow rate, temperature and composition of the regenerants were optimized. Laboratory-scale results indicate that phosphorous in real bioeffluent can be effectively removed from 0.92 mg·L^-1 to<0.5 mg·L^-1 (or even<0.1 mg·L^-1 as desired) by the new adsorbent at a flow rate of 50 bed volume (BV) per hour and treatable volume of 3500–4000 BV per run. Phosphorous removal is independent of the ambient temperature in the range of 15°C–40°C. Moreover, the exhausted HFO-201 can be regenerated by a 2% NaOH+ 5% NaCl binary solution for repeated use without significant capacity loss. A scaled-up study further indicated that even though the initial total phosphorus (TP) was as high as 2 mg·L^-1, it could be reduced to<0.5 mg·L^-1, with a working capacity of 4.4–4.8 g·L^-1 HFO-201. In general, HFO-201 adsorption is a choice method for the efficient removal of phosphate from biotreated waste effluent.     

氨基化氧化石墨烯(AGO)的制备及其对六价铬的吸附机制

以乙二胺盐酸盐(EDH)为改性剂改性氧化石墨烯(GO),水热法制备氨基化氧化石墨烯(Amino-functionalized;graphene;oxide,AGO).SEM、XRD、FTIR和Zeta电位表征分析发现,AGO表面含有羟基、羧基及氨基基团,Zeta电位为pH=10.14.以水中低浓度六价铬Cr(Ⅵ)为污染物,探讨了乙二胺盐酸盐(EDH)用量、pH、AGO用量、Cr(Ⅵ)初始浓度以及常见干扰离子对AGO吸附Cr(Ⅵ)影响.结果表明,在pH=6.0、7-AGO用量为0.8;mg·L^-1和Cr(Ⅵ)初始浓度为2.0;mg·L^-1,7-AGO对Cr(Ⅵ)去除率可达95.1%;SO₄^2-会明显抑制AGO对Cr(Ⅵ)的吸附.AGO对Cr(Ⅵ)的吸附过程符合二级动力学模型,吸附机制主要为静电作用.     

One-pot preparation of graphene oxide magnetic nanocomposites for the removal of tetrabromobisphenol A

A simple solvothermal method was used to prepare monodisperse magnetite (Fe₃O₄) nanoparticles attached onto graphene oxide (GO) sheets as adsorbents to remove tetrabromobisphenol A (TBBPA) from an aqueous solution. These Fe₃O₄/GO (MGO) nanocomposites were characterized by transmission electron microscopy. The adsorption capacity at different initial pH, contact duration, and temperature were evaluated. The kinetics of adsorption was found to fit the pseudo-second-order model perfectly. The adsorption isotherm well fitted the Langmuir model, and the theoretical maximum of adsorption capacity calculated by the Langmuir model was 27.26 mg?g^-1. The adsorption thermodynamics of TBBPA on the MGO nanocomposites was determined at 303 K, 313 K, and 323 K, respectively. The results indicated that the adsorption was spontaneous and endothermic. The MGO nanocomposites were conveniently separated from the media by an external magnetic field within several seconds, and then regenerated in 0.2 M NaOH solution. Thus, the MGO nanocomposites are a promising candidate for TBBPA removal from wastewater.     

Application and mechanism of polysaccharide extracted from Enteromorpha to remove nano-ZnO and humic acid in coagulation process

Green source Ep was extracted from marine alga waste. The molecule model structure of Ep was studied and constructed. PAC-Ep coagulation system improves the efficiency of removal efficiency. Synergistic effects between NPs and HA make a big difference to enhance efficiency. Mechanism is charge neutralization, hydrogen bonding and adsorbing-complexing Enteromorpha polysaccharide (Ep) extracted from alga a novel green coagulant aid for nanoparticles (NPs) and heavy metal ions removal and the structure of EP was intensively studied in this study. The integration of Ep with polyaluminum chloride (PAC-Ep) coagulants exhibited higher coagulation performance than that of the polyaluminum chloride (PAC) because of the negatively charged NPs suspension and humic aid (HA) solution. Significant high removal efficiencies of dissolved organic matter (94.1%), turbidity (99.3%) and Zn ions (69.3%) were achieved by the PAC-Ep coagulants. The dual-coagulation properties of PAC-Ep for different pollutants was based on multiple mechanisms, including (i) Al³⁺ charge neutralization; (ii) hydroxy aluminum hydroxyl bridging formed polynuclearhydroxy complexes bridge and sweep colloidal particles; (iii) adsorption and bridging of Ep chain for the NPs and heavy metal ions. Results indicated that the destabilization of colloid was induced by the coexisting HA and higher removal was achieved as ions adsorption was enhance in the presence of HA complexation. On the basis of that, the extraction of polysaccharide is a promising candidate for its high coagulation performance in water treatment.     

Preparation,characterization of sludge adsorbent and investigations on its removal of hydrogen sulfide under room temperature

To recycle the sludge resource from sewage treatment plants and solve the problem of odor pollution, the sludge was converted into an adsorbent by carbonized pyrolysis and the process was optimized by orthogonal experiments. The capability for odor removal as well as the structure of the adsorbent was studied with H₂S as a target pollutant. The results indicate that the main factor affecting the deodorization performance of the adsorbent is the activating time. The sludge adsorbent sample SAC1 prepared under optimum conditions exhibits the best deodorization performance with a H₂S breakthrough time of 58 min and an iodine value nearly that of the coal activated carbon. The breakthrough time of H₂S is much longer than that on the coal activated carbon. On the other hand, characterization results from X-ray diffractometer (XRD), X-ray photoelectron spectrometer (XPS) and scanning electron microscope (SEM) techniques show that SAC1 is composed of mainly graphite carbon with lower oxygen content on the surface. The bulk of SAC1 exhibits a honeycomb structure with well developed porosity and a high specific surface area of 120.47 m²·g^-1, with the average pore diameter being about 5 nm. Such a structure is in favor of H₂S adsorption. Moreover, SAC1 is detected to contain various metal elements such as Zn, Fe, Mg, etc., leading to a superior deodorization property to that of coal activated carbon.     

Removal of lead from aqueous solution by hydroxyapatite/manganese dioxide composite

A novel composite adsorbent, hydroxyapatite/manganese dioxide (HAp/MnO₂), has been developed for the purpose of removing lead ions from aqueous solutions. The combination of HAp with MnO₂ is meant to increase its adsorption capacity. Various factors that may affect the adsorption efficiency, including solution pH, coexistent substances such as humic acid and competing cations (Ca²⁺, Mg²⁺), initial solute concentration, and the duration of the reaction, have been investigated. Using this composite adsorbent, solution pH and coexistent calcium or magnesium cations were found to have no significant influence on the removal of lead ions under the experimental conditions. The adsorption equilibrium was described well by the Langmuir isotherm model, and the calculated maximum adsorption capacity was 769 mg·g⁻¹. The sorption processes obeyed the pseudo-second-order kinetics model. The experimental results indicate that HAp/MnO₂ composite may be an effective adsorbent for the removal of lead ions from aqueous solutions.     

海泡石黏土矿物对Cu2+的吸附动力学研究

研究分析了海泡石黏土矿物对铜离子的吸附性能和动力学特征,结果表明,海泡石黏土矿物对Cu~(2 )吸附的最佳pH值为6.0左右,随着pH值的增大,吸附作用减弱;在[Cu~(2 )]=100mg·l~(-1),溶液pH值为6,吸附时间为2h时,添加0.1 g海泡石,海泡石对Cu~(2 )的吸附去除率仅为39.5%,当海泡石用量提高至0.4 g时,其对Cu~(2 )的吸附去除率提高到94.8%;实验结果同样显示,18min内有90%的Cu~(2 )被海泡石吸附,随着吸附时间的增加,吸附作用趋于稳定,2h可达到吸附平衡。该吸附过程符合Langmuir和Freundlich等温吸附方程.同时,分别采用拟一级模型和拟二级模型考察了吸附动力学,并计算了这些动力学模型的速率常数.实验数据和拟二级模型计算结果之间有较好的相关性.     

Optimized porous clay heterostructure for removal of acetaldehyde and toluene from indoor air

Adsorption is the most widely used technology for the removal of indoor volatile organic compounds (VOCs). However, existing adsorbent-based technologies are inadequate to meet the regulatory requirement, due to their limited adsorption capacity and efficiency, especially under high relative humidity (RH) conditions. In this study, a series of new porous clay heterostructure (PCH) adsorbents with various ratios of micropores to mesopores were synthesized, characterized and tested for the adsorption of acetaldehyde and toluene. Two of them, PCH25 and PCH50, exhibited markedly improved adsorption capability, especially for hydrophilic acetaldehyde. The improved adsorption was attributed to their large micropore areas and high micropore-to-mesopore volume ratios. The amount of acetaldehyde adsorbed onto PCH25 at equilibrium reached 62.7 mg·g⁻¹, eight times as much as the amount adsorbed onto conventional activated carbon (AC). Even at a high RH of 80%, PCH25 removed seven and four times more of the acetaldehyde than AC and the unmodified raw PCHs did, respectively. This new PCH optimized for their high adsorption and resistance to humidity has promising applications as a cost-effective adsorbent for indoor air purification.     

Preparation of a permanent magnetic hypercrosslinked resin and assessment of its ability to remove organic micropollutants from drinking water

A rapid and effective method based on a novel permanent magnetic hypercrosslinked resin W150 was proposed for the removal of organic micropollutants in drinking water. W150 was prepared by suspension and post-crosslinking reaction and found to possess a high specific surface area of 1149.7 m²·g^-1, a small particle size of 50 μm to 100 μm, and a saturation magnetization as high as 8 emu·g^-1. W150 was used to eliminate nitrofurazone (NFZ) and oxytetracycline (OTC) from drinking water compared with commercial adsorbents XAD-4 and F400D. The adsorption kinetics of NFZ and OTC onto the three adsorbents well fitted the pseudo-second-order equation (r>0.972), and the adsorption isotherms were all well described by the Freundlich equation (r>0.851). Results showed that the reduction in adsorbent size and the enlargement in sorbent pores both accelerated adsorption. Moreover, the effect of particle size on adsorption was more significant than that of pore width. Given that the smallest particle size and the highest specific surface area were possessed by W150, it had the fastest adsorption kinetics and largest adsorption capacity for NFZ (180 mg·g^-1) and OTC (200 mg·g^-1). For the adsorbents with dominant micropores, the sorption of large-sized adsorbates decreased because of the inaccessible micropores. The solution pH and ionic strength also influenced adsorption.     

Selective targeted adsorption and inactivation of antibiotic-resistant bacteria by Cr-loaded mixed metal oxides

• LDHs and MMOs was synthesized by ultrasound-assisted one-step co-precipitation. • MMOs performs the best for Cr(VI) and E. coli_NDM-1 simultaneous removal. • Possible antibacterial pathways of Cr-MMOs were proposed. Herein we provide a novel high-efficiency nanocomposite for bacterial capture based on mixed metal oxides (MMOs) with deleterious chromium properties. With both the layer structure of layered double hydroxides (LDHs) and the magnetic properties of Fe, MMOs enrich the location of ionic forms on the surface, providing a good carrier for adsorption of the heavy metal Cr(VI). The capacity for adsorption of Cr(VI) by MMOs can be as high as 98.80 mg/g. The prepared Cr(VI)-MMOs achieved extremely expeditious location of gram-negative antibiotic-resistant E. coli_NDM-1 by identifying lipid bilayers. Cr-MMOs with a Cr loading of 19.70 mg/g had the best bactericidal effect, and the concentration of E. coli_NDM-1 was decreased from ~10⁸ to ~10³ CFU/mL after 30 min of reaction. The binding of nitrogen and phosphorus hydrophilic groups to chromate generated realistic models for density functional theory (DFT) calculations. The specific selectivity of MMOs toward bacterial cells was improved by taking Cr(VI) as a transferable medium, thereby enhancing the antibacterial activity of Cr-MMOs. Under the combined action of chemical and physical reactions, Cr(VI)-MMOs achieved high capacity for inactivation of bacteria. Moreover, the metallic elements ratio in Cr-MMOs remained stable in their initial valence states after inactivation. This guaranteed high removal efficiency for both heavy metals and bacteria, allowing recycling of the adsorbent in practical applications.     

Optimization of methyl orange removal from aqueous solution by response surface methodology using spent tea leaves as adsorbent

The effective disposal of redundant tea waste is crucial to environmental protection and comprehensive utilization of trash resources. In this work, the removal of methyl orange （MO） from aqueous solution using spent tea leaves as the sorbent was investigated in a batch experiment. First, the effects of various parameters such as temperature, adsorption time, dose of spent tea leaves, and initial concentration of MO were investigated. Then, the response surface methodology （RSM）, based on Box- Behnken design, was employed to obtain the optimum adsorption conditions. The optimal conditions could be obtained at an initial concentration of MO of 9.75 mg·L-1, temperature of 35.3℃, contact time of 63.8 min, and an adsorbent dosage 3.90 g· L-1. Under the optimized condi- tions, the maximal removal of MO was 58.2%. The results indicate that spent tea leaves could be used as an effective and economical adsorbent in the removal of MO from aqueous solution.     

Removal of chromium(VI) by ZnCl2 activated coir pith carbon

The adsorption of chromium(VI) onto ZnCl₂ activated carbon developed from coir pith was investigated to assess the possible use of this adsorbent. The influence of contact time, adsorbent dose, Cr(VI) concentration, pH and temperature were investigated. The two theoretical adsorption isotherms, namely, Langmuir and Freundlich were used to describe the experimental results. The Langmuir adsorption capacity (Q ₀) was found to be 120.5?mg Cr(VI) per g of the adsorbent. The adsorption followed the second-order kinetics and was found to be maximum at pH 2.0. The pH effect and the desorption studies showed that ion exchange mechanism might be involved in the adsorption process. The effects of foreign ions such as chloride, sulphate, phosphate, selenite, molybdate, nitrate and perchlorate on the removal of Cr(VI) have been investigated. The removal of Cr(VI) from synthetic ground water was also tested. The results show that ZnCl₂ activated coir pith carbon is effective for the removal of Cr(VI) from water.