Effect of gas composition in Chemical-Looping Combustion with copper-based oxygen carriers: Fate of sulphur

Chemical-Looping Combustion (CLC) is an emerging technology for CO₂ capture because separation of this gas from the other flue gas components is inherent to the process and thus no energy is expended for the separation. Natural or refinery gas can be used as gaseous fuels and they may contain different amounts of sulphur compounds, such as H₂S and COS. This paper presents the combustion results obtained with a Cu-based oxygen carrier using mixtures of CH₄ and H₂S as fuel. The influence of H₂S concentration on the gas product distribution and combustion efficiency, sulphur splitting between the fuel reactor (FR) and the air reactor (AR), oxygen carrier deactivation and material agglomeration was investigated in a continuous CLC plant (500 W_th). The oxygen carrier to fuel ratio, ?, was the main operating parameter affecting the CLC system. Complete fuel combustion were reached at 1073 K working at ? values ≥1.5. The presence of H₂S did not produce a decrease in the combustion efficiency even when working with a fuel containing 1300 vppm H₂S. At these conditions, the great majority of the sulphur fed into the system was released in the gas outlet of the FR as SO₂, affecting to the quality of the CO₂ produced. Formation of copper sulphide, Cu₂S, and the subsequent reactivity loss was only detected working at low values of ? ≤ 1.5, although this fact did not produce any agglomeration problem in the fluidized beds. In addition, the oxygen carrier was fully regenerated in a H₂S-free environment. It can be concluded that Cu-based oxygen carriers are adequate materials to be used in a CLC process using fuels containing H₂S although quality of the CO₂ produced is affected.     

Chemical-looping combustion using syngas as fuel

Chemical-looping combustion (CLC) is a combustion technology where an oxygen carrier is used to transfer oxygen from the combustion air to the fuel, avoiding direct contact between air and fuel. Thus, CO₂ and H₂O are inherently separated from the rest of the flue gases and the carbon dioxide can be obtained in a pure form without the use of an energy intensive air separation unit. The paper presents results from a 3-year project devoted to developing the CLC technology for use with syngas from coal gasification. The project has focused on: (i) the development of oxygen carrier particles, (ii) establishing a reactor design and feasible operating conditions and (iii) construction and operation of a continuously working hot reactor. Approximately, 300 different oxygen carriers based on oxides of the metals Ni, Fe, Mn and Cu were investigated with respect to parameters, which are important in a CLC system, and from these investigations, several particles were found to possess suitable qualities as oxygen carriers. Several cold-model prototypes of CLC based on interconnected fluidized bed reactors were tested, and from these tests a hot prototype CLC reactor system was constructed and operated successfully using three carriers based on Ni, Fe and Mn developed within the project. The particles were used for 30–70 h with combustion, but were circulated under hot conditions for 60–150 h.     

Numerical simulation of chemical looping combustion process with CaSO4 oxygen carrier

Chemical-looping combustion (CLC) is a promising technology for the combustion of gas or solid fuel with efficient use of energy and inherent separation of CO₂. The technique involves the use of an oxygen carrier which transfers oxygen from combustion air to the fuel, and hence a direct contact between air and fuel is avoided. A chemical-looping combustion system consists of a fuel reactor and an air reactor. A metal oxide is used as oxygen carrier that circulates between the two reactors. The air reactor is a high velocity fluidized bed where the oxygen carrier particles are transported together with the air stream to the top of the air reactor, where they are then transferred to the fuel reactor using a cyclone. The fuel reactor is a bubbling fluidized bed reactor where oxygen carrier particles react with hydrocarbon fuel and get reduced. The reduced oxygen carrier particles are transported back to the air reactor where they react with oxygen in the air and are oxidized back to metal oxide. The exhaust from the fuel reactor mainly consists of CO₂ and water vapor. After condensation of the water in the exit gas from the fuel reactor, the remaining CO₂ gas is compressed and cooled to yield liquid CO₂, which can be disposed of in various ways.With the improvement of numerical methods and more advanced hardware technology, the time needed to run CFD (Computational fluid dynamics) codes is decreasing. Hence multiphase CFD-based models for dealing with complex gas-solid hydrodynamics and chemical reactions are becoming more accessible. Until now there were a few literatures about mathematical modeling of chemical-looping combustion using CFD approach. In this work, the reaction kinetics model of the fuel reactor (CaSO₄ + H₂) was developed by means of the commercial code FLUENT. The bubble formation and the relation between bubble formation and molar fraction of products in gas phase were well captured by CFD simulation. Computational results from the simulation also showed low fuel conversion rate. The conversion of H₂ was about 34% partially due to fast, large bubbles rising through the reactor, low bed temperature and large particles diameter.     

Waste products from the steel industry with NiO as additive as oxygen carrier for chemical-looping combustion

Fe₂O₃-containing waste materials from the steel industry are proposed as oxygen carrier for chemical-looping combustion. Three such materials, red iron oxide, brown iron oxide and iron oxide scales, have been examined by oxidation and reduction experiments in a batch fluidized-bed reactor at temperatures between 800 and 950 °C. NiO-based particles have been used as additive, in order to examine if it is possible to utilize the catalytic properties of metallic Ni to facilitate decomposition of hydrocarbons into more reactive combustion intermediates such as CO and H₂. The experiments indicated modest reactivity between the waste materials and CH₄, which was used as reducing gas. Adding small amounts of NiO-based particles to the sample increased the yield of CO₂ in a standard experiment, typically by a factor of 1.5–3.5. The fraction of unconverted fuel typically was reduced by 70–90%. The conversion of CH₄ to CO₂ was 94% at best, corresponding to a combustion efficiency of 96%. This was achieved using a bed mass corresponding to 57 kg oxygen carrier per MW fuel, of which only 5 wt% was NiO-based synthetic particles. The different materials fared differently well during the experiments. Red iron oxide was fairly stable, while brown iron oxide was soft and subject to considerable erosion. Iron oxide scales experienced increased reactivity and porosity as function of the numbers of reduction cycles.     

Reduction of CaSO4 oxygen carrier with coal in chemical-looping combustion: Effects of temperature and gasification intermediate

Chemical-looping combustion (CLC) has been suggested as an energy efficient method for the capture of carbon dioxide from combustion. Thermodynamics and kinetics of CaSO₄ reduction with coal via gasification intermediate in a CLC process were discussed in the paper, with respect to the CO₂ generating efficiency, the environmental factor and the surface morphology of oxygen carrier. Tests on the combined process of coal gasification and CaSO₄ reduction with coal syngas were conducted in a batch fluidized bed reactor at different reaction temperatures and with different gasification intermediates. The products were characterized by gas chromatograph, gas analyzers and scanning electron microscope. And the results showed that an increase in the reaction temperature aggravated the SO₂ emission. The CO₂ generating efficiency also increased with the temperature, but it decreased when the temperature exceeded 950 °C due to the sintering of oxygen carrier particles. The use of CO₂ as gasification intermediate in the fuel reactor had a positive effect on the sintering-resistant of oxygen carrier particles. However, increasing the steam/CO₂ ratio in gasification intermediate evidently enhanced CO₂ generating efficiency and reduced SO₂ environmental impact.     

Operating experience with chemical looping combustion in a 120 kW dual circulating fluidized bed (DCFB) unit

This study presents first operating experience with a 120 kW chemical looping pilot rig. The dual circulating fluidized bed reactor system and its auxiliary units are discussed. Two different oxygen carriers, i.e. ilmenite, which is a natural iron titanium ore, and a designed Ni-based particle, are tested in the CLC unit. The pilot rig is fueled with H₂, CO and CH₄ respectively at a fuel power of 65–145 kW. High solids circulation, very low solids residence time and low solids inventory are observed during operation. Owing to the scalability of the design concept, these characteristics should be quite similar to those of commercial CLC power plants. Ilmenite shows a high potential for the combustion of H₂-rich gases (e.g. from coal gasification with steam). The H₂ conversion is quite high but there is still a high potential for further improvement. The Ni-based oxygen carrier achieves the thermodynamic maximum H₂ and CO conversion and also very high CH₄ conversion. A variation of the air/fuel ratio and the reaction temperature indicates that the Ni/NiO ratio of the particle has an influence on the performance of the chemical looping combustor. Generally, low solids conversion in air and fuel reactors is observed in almost any conditions. Despite a very low H₂O/CH₄ molar ratio, no carbon formation is observed.     

Pulverized coal stream ignition delay under conventional and oxy-fuel combustion conditions

The coal stream ignition process is critical to the performance of modern pulverized coal burners, particularly when operating under novel conditions such as experienced in oxy-fuel combustion. However, experimental studies of coal stream ignition are lacking, and recent modeling efforts have had to rely on comparisons with a single set of experiments in vitiated air. To begin to address this shortfall, we have conducted experiments on the ignition properties of two U.S. and two Chinese coals in a laminar entrained flow reactor. Most of the measurements focused on varying the coal feed rate for furnace temperatures of 1230–1320 K and for 12–20 vol.% O₂ in nitrogen. The influence of coal feed rate on ignition with a carbon dioxide diluent was also measured for 20 vol.% O₂ at 1280 K. A second set of measurements was performed for ignition of a fixed coal feed rate in N₂ and CO₂ environments at identical furnace temperatures of 1200 K, 1340 K, and 1670 K. A scientific CCD camera equipped with a 431 nm imaging filter was used to interrogate the ignition process. Under most conditions, the ignition delay decreased with increasing coal feed rate until a minimum was reached at a feed rate corresponding to a particle number density of approximately 4 × 10⁹ m^?3 in the coal feed pipe. This ignition minimum corresponds to a cold flow group number, G, of ～0.3. At higher coal feed rates the ignition delay increased. The ignition delay time was shown to be very sensitive to (a) the temperature of the hot coflow into which the coal stream is introduced, and (b) the coal particle size. The three high volatile bituminous coals showed nearly identical ignition delay as a function of coal feed rate, whereas the subbituminous coal showed slightly greater apparent ignition delay. Bath gas CO₂ content was found to have a minor impact on ignition delay.     

Multi-stage chemical looping combustion (CLC) for combined cycles with CO2 capture

This paper presents application of the chemical looping combustion (CLC) method in natural gas-fired combined cycles for power generation with CO₂ capture. A CLC combined cycle consisting of single CLC-reactor system, an air turbine, a CO₂-turbine and a steam cycle has been designated as the base-case cycle. The base-case cycle can achieve net plant efficiency of about 52% at an oxidation temperature of 1200 °C. In order to achieve a reasonable efficiency at lower oxidation temperatures, reheat is introduced into the air turbine by employing multi CLC-reactors. The results show that the single reheat CLC-combined cycle can achieve net plant efficiency of above 51% at oxidation temperature of 1000 °C and above 53% at the oxidation temperature of 1200 °C including CO₂ compression to 110 bar. The double reheat cycle results in marginal efficiency improvement as compared to the single reheat cycle. The CLC-cycles are also compared with a conventional combined cycle with and without post-combustion capture in amine solution. All the CLC-cycles show higher net plant efficiencies with close to 100% CO₂ capture as compared to a conventional combined cycle with post-combustion capture, which is very promising.     

Energy balances,greenhouse gas emissions and economics of biochar production from palm oil empty fruit bunches

This paper presents results from a gate-to-gate analysis of the energy balance, greenhouse gas (GHG) emissions and economic efficiency of biochar production from palm oil empty fruit bunches (EFB). The analysis is based on data obtained from EFB combustion in a slow pyrolysis plant in Selangor, Malaysia. The outputs of the slow pyrolysis plant are biochar, syngas, bio-oil and water vapor. The net energy yield of the biochar produced in the Selangor plant is 11.47 MJ kg⁻¹ EFB. The energy content of the biochar produced is higher than the energy required for producing the biochar, i.e. the energy balance of biochar production is positive. The combustion of EFB using diesel fuel has the largest energy demand of 2.31 MJ kg⁻¹ EFB in the pyrolysis process. Comparatively smaller amounts of energy are required as electricity (0.39 MJ kg⁻¹ EFB) and for transportation of biochar to the warehouse and the field (0.13 MJ kg⁻¹ EFB). The net greenhouse gas emissions of the studied biochar production account for 0.046 kg CO₂-equiv. kg⁻¹ EFB yr⁻¹ without considering fertilizer substitution effects and carbon accumulation from biochar in the soil. The studied biochar production is profitable where biochar can be sold for at least 533 US-$ t⁻¹. Potential measures for improvement are discussed, including higher productivity of biochar production, reduced energy consumption and efficient use of the byproducts from the slow pyrolysis.     

160 h of chemical-looping combustion in a 10 kW reactor system with a NiO-based oxygen carrier

Chemical-looping combustion, CLC, is a technology with inherent separation of the greenhouse gas CO₂. The technique uses an oxygen carrier made up of particulate metal oxide to transfer oxygen from combustion air to fuel. In this work, an oxygen carrier consisting of 60% NiO and 40% NiAl₂O₄ was used in a 10 kW CLC reactor system for 160 h of operation with fuel. The first 3 h of fuel operation excepted, the test series was accomplished with the same batch of oxygen carrier particles. The fuel used in the experiments was natural gas, and a fuel conversion to CO₂ of approximately 99% was accomplished. Combustion conditions were very stable during the test period, except for the operation at sub-stoichiometric conditions. It was shown that the methane fraction in the fuel reactor exit gas was dependent upon the rate of solids circulation, with higher circulation leading to more unconverted methane. The carbon monoxide fraction was found to follow the thermodynamical equilibrium for all investigated fuel reactor temperatures, 660–950 °C. Thermal analysis of the fuel reactor at stable conditions enabled calculation of the particle circulation which was found to be approximately 4 kg/s, MW. The loss of fines, i.e. the amount of elutriated oxygen carrier particles with diameter <45 μm, decreased during the entire test period. After 160 h of operation the fractional loss of fines was 0.00022 h⁻¹, corresponding to a particle life time of 4500 h.     

Development and testing of AZEP reactor components

The advanced zero emissions power plant (AZEP) project addresses the development of a novel “zero emissions,” gas turbine-based, power generation process to reduce local and global CO₂ emissions in a cost-effective way.The key element in AZEP is an integrated MCM-reactor, in which (a) O₂ is separated from air by means of a mixed-conducting membrane (MCM), (b) combustion of natural gas occurs in an N₂-free environment and (c) the heat of combustion is transferred to air by heat exchange.This paper focuses on the development and testing of the ceramic components of the MCM-reactor (air separation membrane and heat exchangers). For compactness and manufacturability, a module design based on extruded square channel monoliths has been chosen. The manifold design enables gas distribution in a checkerboard pattern. Modules with contact area of >500 m²/m³ have been produced.Results from testing of the modules under close to realistic process conditions agree with model predictions. Extrapolation to AZEP process conditions gives an oxygen production rate of around 37 mol O₂/(m³ s), or 15 MW/m³ power density (per net MCM volume). These values correspond to project targets and confirm the feasibility of the AZEP concept.     

CO2 capture from combined cycles integrated with Molten Carbonate Fuel Cells

In this paper Molten Carbonate Fuel Cells (MCFCs) are considered for their potential application in carbon dioxide separation when integrated into natural gas fired combined cycles. The MCFC performs on the anode side an electrochemical oxidation of natural gas by means of CO₃^2? ions which, as far as carbon capture is concerned, results in a twofold advantage: the cell removes CO₂ fed at the cathode to promote carbonate ion transport across the electrolyte and any dilution of the oxidized products is avoided.The MCFC can be “retrofitted” into a combined cycle, giving the opportunity to remove most of the CO₂ contained in the gas turbine exhaust gases before they enter the heat recovery steam generator (HRSG), and allowing to exploit the heat recovery steam cycle in an efficient “hybrid” fuel cell + steam turbine configuration. The carbon dioxide can be easily recovered from the cell anode exhaust after combustion with pure oxygen (supplied by an air separation unit) of the residual fuel, cooling of the combustion products in the HRSG and water separation. The resulting power cycle has the potential to keep the overall cycle electrical efficiency approximately unchanged with respect to the original combined cycle, while separating 80% of the CO₂ otherwise vented and limiting the size of the fuel cell, which contributes to about 17% of the total power output so that most of the power capacity relies on conventional low cost turbo-machinery. The calculated specific energy for CO₂ avoided is about 4 times lower than average values for conventional post-combustion capture technology. A sensitivity analysis shows that positive results hold also changing significantly a number of MCFC and plant design parameters.     

Ash and deposit formation from oxy-coal combustion in a 100 kW test furnace

Ash deposition is still an unresolved problem when retrofitting existing air-fired coal power plants to oxy-fuel combustion. Experimental data are quite necessary for mechanism validation and model development. This work was designed to obtain laboratory combustor data on ash and deposits from oxy-coal combustion, and to explore the effects of oxy-firing on their formation. Two bituminous coals (Utah coal and Illinois coal) and one sub-bituminous coal (PRB coal) were burned on a down-fired combustor under both oxy- and air-firing. Two oxy-fired cases, i.e., 27 vol% O₂/73 vol% CO₂ and 32 vol% O₂/68 vol% CO₂, were selected to match the radiation flux and the adiabatic flame temperature of air combustion, respectively. Once-through CO₂ was used to simulate fully cleaned recycled flue gas. The flue gas excess oxygen was fixed at 3 vol%. For each case, both size-segregated fly ash and bulk fly ash samples were obtained. Simultaneously, ash deposits were collected on an especially designed un-cooled deposition probe. Ash particle size distributions and chemical composition of all samples were characterized. Data showed that oxy-firing had insignificant impacts on the tri-modal ash particle size distributions and composition size distributions in the size range studied. Bulk ash compositions also showed no significant differences between oxy- and air-firing, except for slightly higher sulfur contents in some oxy-fired ashes. The oxy-fired deposits were thicker than those from air-firing, suggesting enhanced ash deposition rates in oxy-firing. Oxy-firing also had apparent impacts on the deposit composition, especially for those components (e.g., CaO, Fe₂O₃, SO₃, etc.) that could contribute significantly to ash deposition. Based on these results, aerodynamic changes in gas flow and changes in combustion temperature seemed more important than chemical changes of ash particles in determining deposit behavior during oxy-coal combustion.     

Study of Hg and SO3 behavior in flue gas of oxy-fuel combustion system

Oxy-fuel combustion systems have been under development to reduce CO₂ emissions from coal-fired power plants. In oxy-fuel combustion system, Hg in the flue gas causes corrosion in CO₂ purification and compression units. Also, SO₃ in the flue gas corrodes the equipment and ducts of oxy-fuel combustion system. Therefore, Hg and SO₃ need to be removed.Babcock-Hitachi conducted tests using a 1.5 MWth Combustion & Air Quality Control System (AQCS) test facility which consists of oxygen supply unit, furnace, Selective Catalytic Reduction (SCR) catalyst, Clean Energy Recuperator (CER), Dry Electrostatic Precipitator (DESP), flue gas recirculation system, Wet Flue Gas Desulfurization (WFGD), and CO₂ Compression and Purification Unit (CPU). In both cases of air and oxy-fuel combustion, the Hg removal across the DESP could be improved, and SO₃ concentration at the DESP outlet could be reduced to less than 1 ppm by installing a CER upstream of the DESP and reducing the gas temperature at the DESP inlet. Hg was not dissolved in the drain recovered from CO₂ compressor, and may be adsorbed at an inner part of CO₂ compressor. This indicated that Hg needs to be removed at a location upstream of the CO₂ compressor to prevent corrosion of the compressor.     

Pathways towards large-scale implementation of CO2 capture and storage: A case study for the Netherlands

We sketch four possible pathways how carbon dioxide capture and storage (CCS) (r)evolution may occur in the Netherlands, after which the implications in terms of CO₂ stored and avoided, costs and infrastructural requirements are quantified. CCS may play a significant role in decarbonising the Dutch energy and industrial sector, which currently emits nearly 100 Mt CO₂/year. We found that 15 Mt CO₂ could be avoided annually by 2020, provided some of the larger gas fields that become available the coming decade could be used for CO₂ storage. Halfway this century, the mitigation potential of CCS in the power sector, industry and transport fuel production is estimated at maximally 80–110 Mt CO₂/year, of which 60–80 Mt CO₂/year may be avoided at costs between 15 and 40 €/t CO₂, including transport and storage. Avoiding 30–60 Mt CO₂/year by means of CCS is considered realistic given the storage potential represented by Dutch gas fields, although it requires planning to assure that domestic storage capacity could be used for CO₂ storage. In an aggressive climate policy, avoiding another 50 Mt CO₂/year may be possible provided that nearly all capture opportunities that occur are taken. Storing such large amounts of CO₂ would only be possible if the Groningen gas field or large reservoirs in the British or Norwegian part of the North Sea will become available.     

Experimental validation of in situ CO2 capture with CaO during the low temperature combustion of biomass in a fluidized bed reactor

A novel concept for capturing CO₂ from biomass combustion using CaO as an active solid sorbent of CO₂ is discussed and experimentally tested. According to the CaO/CaCO₃ equilibrium, if a fuel could be burned at a sufficiently low temperature (below 700 °C) it would be possible to capture CO₂ “in situ” with the CaO particles at atmospheric pressure. A subsequent step involving the regeneration of CaCO₃ in a calciner operating at typical conditions of oxyfired-circulating fluidized combustion would deliver the CO₂ ready for purification, compression and permanent geological storage. Several series of experiments to prove this concept have been conducted in a 30 kW interconnected fluidized bed test facility at INCAR-CSIC, made up of two interconnected circulating fluidized bed reactors, one acting as biomass combustor-carbonator and the other as air-fired calciner (which is considered to yield similar sorbent properties than those of an oxyfired calciner). CO₂ capture efficiencies in dynamic tests in the combustor-carbonator reactor were measured over a wide range of operating conditions, including different superficial gas velocities, solids circulation rates, excess air above stoichiometric, and biomass type (olive pits, saw dust and pellets). Biomass combustion in air is effective at temperatures even below the 700 °C, necessary for the effective capture of CO₂ by carbonation of CaO. Overall CO₂ capture efficiencies in the combustor-carbonator higher than 70% can be achieved with sufficiently high solids circulation rates of CaO and solids inventories. The application of a simple reactor model for the combined combustion and CO₂ capture reactions allows an efficiency factor to be obtained from the dynamic experimental test that could be valuable for scaling up purposes.     

A comparison of on-site nutrient and energy recycling technologies in algal oil production

Research on biofuel production pathways from algae continues because among other potential advantages they avoid key consequential effects of terrestrial oil crops, such as competition for cropland. However, the economics, energetic balance, and climate change emissions from algal biofuels pathways do not always show great potential, due in part to high fertilizer demand. Nutrient recycling from algal biomass residue is likely to be essential for reducing the environmental impacts and cost associated with algae-derived fuels. After a review of available technologies, anaerobic digestion (AD) and hydrothermal liquefaction (HTL) were selected and compared on their nutrient recycling and energy recovery potential for lipid-extracted algal biomass using the microalgae strain Scenedesmus dimorphus. For 1 kg (dry weight) of algae cultivated in an open raceway pond, 40.7 g N and 3.8 g P can be recycled through AD, while 26.0 g N and 6.8 g P can be recycled through HTL. In terms of energy production, 2.49 MJ heat and 2.61 MJ electricity are generated from AD biogas combustion to meet production system demands, while 3.30 MJ heat and 0.95 MJ electricity from HTL products are generated and used within the production system.Assuming recycled nutrient products from AD or HTL technologies displace demand for synthetic fertilizers, and energy products displace natural gas and electricity, the life cycle greenhouse gas reduction achieved by adding AD to the simulated algal oil production system is between 622 and 808 g carbon dioxide equivalent (CO₂e)/kg biomass depending on substitution assumptions, while the life cycle GHG reduction achieved by HTL is between 513 and 535 g CO₂e/kg biomass depending on substitution assumptions. Based on the effectiveness of nutrient recycling and energy recovery, as well as technology maturity, AD appears to perform better than HTL as a nutrient and energy recycling technology in algae oil production systems.     

Assessment of the different parameters affecting the CO2 purity from coal fired oxyfuel process

The oxyfuel process is one of the most promising options to capture CO₂ from coal fired power plants. The combustion takes place in an atmosphere of almost pure oxygen, delivered from an air separation unit (ASU), and recirculated flue gas. This provides a flue gas containing 80–90 vol% CO₂ on a dry basis. Impurities are caused by the purity of the oxygen from the ASU, the combustion process and air ingress. Via liquefaction a CO₂ stream with purity in the range from 85 to 99.5 vol% can be separated and stored geologically. Impurities like O₂, NO_X, SO_X, and CO may negatively influence the transport infrastructure or the geological storage site by causing geochemical reactions. Therefore the maximum acceptable concentrations of the impurities in the separated CO₂ stream must be defined regarding the requirements from transportation and storage. The main objective of the research project COORAL therefore is to define the required CO₂ purity for capture and storage.     

Kinetics of sulfur dioxide- and oxygen-induced degradation of aqueous monoethanolamine solution during CO2 absorption from power plant flue gas streams

Studies of the kinetics of sulfur dioxide (SO₂)- and oxygen (O₂)-induced degradation of aqueous monoethanolamine (MEA) during the absorption of carbon dioxide (CO₂) from flue gases derived from coal- or natural gas-fired power plants were conducted as a function of temperature and the liquid phase concentrations of MEA, O₂, SO₂ and CO₂. The kinetic data were based on the initial rate which shows the propensity for amine degradation and obtained under a range of conditions typical of the CO₂ absorption process (3–7 kmol/m³ MEA, 6% O₂, 0–196 ppm SO₂, 0–0.55 CO₂ loading, and 328–393 K temperature). The results showed that an increase in temperature and the concentrations of MEA, O₂ and SO₂ resulted in a higher MEA degradation rate. An increase in CO₂ concentration gave the opposite effect. A semi-empirical model based on the initial rate, ?r_MEA = {6.74 × 10⁹ e^?(29,403/RT)[MEA]^0.02([O]^2.91 + [SO₂]^3.52)}/{1 + 1.18[CO₂]^0.18} was developed to fit the experimental data. With the higher order of reaction, SO₂ has a higher propensity to cause MEA to degrade than O₂. Unlike previous models, this model shows an improvement in that any of the parameters (i.e. O₂, SO₂, and CO₂) can be removed without affecting the usability of the model.     

Capture of carbon dioxide from flue or fuel gas mixtures by clathrate crystallization in a silica gel column

A column of silica gel was employed to contact water with flue gas (CO₂/N₂) mixture to assess if CO₂ can be separated by hydrate crystallization. Three different silica gels were used. One with a pore size of 30 nm (particle size 40–75 μm) and two with a pore size of 100 nm and particle sizes of 40–75 and 75–200 μm respectively. The observed trends indicate that larger pores and particle size increase the gas consumption, CO₂ recovery, separation factor and water conversion to hydrate. Thus, the gel (gel #3) with the larger particle size and larger pore size was chosen to carry out experiments with concentrated CO₂ mixtures and for experiments in the presence of tetrahydrofuran (THF), which itself is a hydrate forming substance. Addition of THF reduces the operating pressure in the crystallizer but it also reduces the gas uptake. Gel #3 was also used in experiments with a fuel gas (CO₂/H₂) mixture in order to recover CO₂ and H₂. It was found that the gel column performs as well as a stirred reactor in separating the gas components from both flue gas and fuel gas mixtures. However, the crystallization rate and hydrate yield are considerably enhanced in the former. Finally the need for stirring is eliminated with the gel column which is enormously beneficial economically.