Kinetics of simazine advanced oxidation in water

Comparison of the effects and kinetics of UV photolysis and four advanced oxidation systems (ozone, ozone/hydrogen peroxide, ozone/UV radiation and UV radiation/hydrogen peroxide) for the removal of simazine from water has been investigated. At the conditions applied, the order of reactivity was ozone < ozone/hydrogen peroxide < UV radiation < ozone/UV radiation and UV radiation/hydrogen peroxide. Rate constants of the reactions between ozone and simazine and hydroxyl radical and simazine were found to be 8.7 M-1s-1 and 2.1 x 10(9) M-1s-1, respectively. Also, a quantum yield of 0.06 mol.photon-1 was found for simazine at 254 nm UV radiation. The high value of the quantum yield corroborated the importance of the direct photolysis process. Percentage contributions of direct reaction with ozone, reaction with hydroxyl radicals and direct photolysis were also quantified.     

Hydroxyl (OH) radical production rates in snowpacks from photolysis of hydrogen peroxide (H2O2) and nitrate (NO3−)

Atmospheric chemistry directly above snowpacks is strongly influenced by ultraviolet (UV) radiation initiated emissions of chemicals from the snowpack. The emission of gases from the snowpack to the atmosphere is in part due to chemical reactions between hydroxyl radical, OH (produced from photolysis of hydrogen peroxide (H₂O₂) or nitrate (NO₃⁻)) and impurities in the snowpack. The work presented here is a radiative-transfer modelling study to calculate the depth-integrated production rates of hydroxyl radical from the photolysis of hydrogen peroxide and nitrate anion in snow for four different snowpacks and for solar zenith angles 30°–90°. This work also demonstrates the importance of hydrogen peroxide photolysis to produce hydroxyl radical relative to nitrate photolysis with (a) different snowpacks, (b) different ozone column depths, and (c) snowpack depths. The importance of hydrogen peroxide photolysis over nitrate photolysis for hydroxyl radical production increases with increasing depth in snowpack, column ozone depth, and solar zenith angle. With a solar zenith angle of 60° the production of hydroxyl radical from hydrogen peroxide photolysis accounts for 91–99% of all hydroxyl radical production from hydrogen peroxide and nitrate photolysis.     

Atrazine removal by ozonation processes in surface waters

Abstract

Atrazine (6‐chloro‐N‐ethyl‐N'‐isopropyl‐1,3,5‐triazinedyl‐2,4‐diamine) was treated with ozone alone and in combination with hydrogen peroxide or UV radiation in three surface waters. Experiments were carried out in two bubble reactors operated continously. Variables investigated were the ozone partial pressure, temperature, pH, mass flow ratio of oxidants fed: hydrogen peroxide and ozone and the type of oxidation including UV radiation alone. Residence time for the aqueous phase was kept at 10 min. Concentrations of some intermediates, including deethylatrazine, deisopropylatrazine and deethyldeisopropylatrazine, were also followed. The nature of water, specifically the alkalinity and pH were found to be important variables that affected atrazine (ATZ) removal. Surface waters with low alkalinity and high pH allowed the highest removal of ATZ to be reached. There was an optimum hydrogen peroxide to ozone mass flow ratio that resulted in the highest ATZ removal in each surface water treated. This optimum was above the theoretical stoichiometry of the process. Therefore, to reach the maximum removal of ATZ in a O₃/H₂O₂ process, more hydrogen peroxide was needed in the surface waters treated than in ultrapure water under similar experimental conditions. In some cases, UV radiation alone resulted in the removal of ATZ higher than ozonation alone. This was likely due to the alkalinity of the surface water. Ozonation and UV radiation processes yield different amounts of hydrogen peroxide. Combined ozonations (O₃/H₂O₂ and O₃/UV) lead to ATZ removals higher than single ozonation or UV radiation but the formation of intermediates was higher.     

Decomposition of gas-phase trichloroethene by the UV/TiO2 process in the presence of ozone.

The decomposition of gas-phase trichloroethene (TCE) in air streams by direct photolysis, the UV/TiO2 and UV/O3 processes was studied. The experiments were carried out under various UV light intensities and wavelengths, ozone dosages, and initial concentrations of TCE to investigate and compare the removal efficiency of the pollutant. For UV/TiO2 process, the individual contribution to the decomposition of TCE by direct photolysis and hydroxyl radicals destruction was differentiated to discuss the quantum efficiency with 254 and 365 nm UV lamps. The removal of gaseous TCE was found to reduce by UV/TiO2 process in the presence of ozone possibly because of the ozone molecules could scavenge hydroxyl radicals produced from the excitation of TiO2 by UV radiation to inhibit the decomposition of TCE. A photoreactor design equation for the decomposition of gaseous TCE by the UV/TiO2 process in air streams was developed by combining the continuity equation of the pollutant and the surface catalysis reaction rate expression. By the proposed design scheme, the temporal distribution of TCE at various operation conditions by the UV/TiO2 process can be well modeled.     

Assessment and optimisation of VOC mass transfer enhancement by advanced oxidation process in a compact wet scrubber

Dimethyl disulphide (DMDS) removal was investigated in a compact scrubber (hydraulic residence time ≈20 ms), composed of a wire mesh packing structure where liquid and gas flow at co-current and high gas superficial velocity (>12 m s⁻¹). In order to regenerate the scrubbing liquid and to maintain a driving force in the scrubber, ozone and hydrogen peroxide were added to water since they allow the generation of nonselective and highly reactive species, hydroxyl radicals HO. Three ways of reagent distribution were tested. The influence of several parameters (liquid flow rate(s), ozone flow rate, pH and reagent concentrations) was investigated. The best configuration was obtained when ozone is transferred in the scrubbing liquid before introduction at the top of the scrubber simultaneously with the hydrogen peroxide solution, allowing to generate hydroxyl radical in the scrubber. With this configuration, DMDS removal could be increased from 16% with water to 34% at the same gas and liquid flow rates in the scrubber showing the potentiality of advanced oxidation process.     

Advanced oxidation of alkylphenol ethoxylates in aqueous systems

Alkylphenols and alkylphenol ethoxylates are ubiquitous wastewater contaminants. In this study the oxidation of nonylphenol ethoxylates (NPEO) and octylphenol ethoxylates (OPEO) by oxidant systems generating hydroxide radicals was evaluated. The reaction of each oxidant with a technical mixture of NPEO (Tergitol™) and OPEO (Triton X-100™) in ultrapure laboratory water and four aqueous environmental matrices was carried out in order to develop an understanding of reaction kinetics. The oxidation of APEOs was evaluated by hydroxyl radical generated by (1) hydrogen peroxide in the presence of ultraviolet light, (2) Fenton’s reagent, and (3) a photo-Fenton’s process. The second order kinetic rate constant for both NPEO and OPEO with hydroxyl radical was calculated to be 1.1 × 10¹⁰ M⁻¹ s⁻¹. The efficacy of the AOPs within an aqueous environmental matrix was dependent on the rate of formation of hydroxyl radical and the scavenging capacity of the matrix. A model based on the hydroxyl radical formation, scavenging capacity and the kinetic rate constant of target APEO was developed from the existing literature and applied to predict the concentration of APEOs in solution during advanced oxidation in different aqueous environmental matrices.     

Oxidation of MCPA and 2,4-D by UV radiation, ozone, and the combinations UV/H2O2 and O3/H2O2

The phenoxyalkyl acid derivative herbicides MCPA (4-chloro 2-methylphenoxyacetic acid) and 2,4-D (2,4-dichlorophenoxyacetic acid) were oxidized in ultrapure water by means of a monochromatic UV irradiation and by ozone, as well as by the combinations UV/H2O2 and O3/H2O2. In the direct photolysis of MCPA, the quantum yield at 20 degrees C was directly evaluated and a value of 0.150 mol Eins(-1) was obtained in the pH range 5-9, while a lower value of 0.41 x 10(-2) mol Eins(-1) was determined at pH=3. Similarly, for 2,4-D a value of 0.81 x 10(-2) mol Eins(-1) was deduced, independent of the pH of work. The influence of the additional presence of hydrogen peroxide was established in the combined process UV/H2O2, and the specific contribution of the radical pathway to the global photo-degradation was evaluated. The oxidation by ozone and by the combination O3/H2O2 was also studied, with the determination of the rate constants for the reactions of both herbicides with ozone and hydroxyl radicals at 20 degrees C. These rate constants for the direct reactions with ozone were 47.7 and 21.9 M(-1) s(-1) for MCPA and 2,4-D respectively, while the found values for the rate constants corresponding to the radical reactions were 6.6 x 10(9) and 5.1 x 10(9) M(-1) s(-1).     

SMX degradation by ozonation and UV radiation: a kinetic study

The rate constants of sulfamethoxazole (SMX) degradation by ozonation and UV₂₅₄ radiation were investigated under various parameters including influent ozone gas concentration, initial SMX concentration, UV light intensity, ionic strength, water quality in terms of varying anions (bicarbonate, sulfate and nitrate), humic acid (HA) and pH. The results indicated that the removal of SMX by ozonation and UV₂₅₄ radiation fitted well to a pseudo first-order kinetic model and the rate constants were in the range of (0.9-9.8) × 10⁻³ and (1.7-18.9) × 10⁻³ s⁻¹, respectively. The second-order rate constants of SMX with ozone (k_O3), under varying operational parameters, were also determined and varied in the range of (0.60-3.38) ± 0.13 × 10⁵ M⁻¹ s⁻¹. In addition, SMX degradation through UV pretreatment followed by ozonation in the presence of HA was proved to be an effective method which can remove SMX with a low ozone dose. The results suggested that ozonation of SMX was more affected by concentration of influent ozone gas, alkalinity, and HA, while incident UV light intensity, pH, and HA were the dominant factors influencing UV degradation of SMX.     

Kinetics and mechanisms of interaction of simazine with humic acids

Abstract

The adsorption of simazine on two fractions of hu‐mic acids of different molecular size was investigated at a pH range of 2.5 to 6.2. The amounts of the herbicide adsorbed decreased with increasing pH for both of the two humic acids fractions used and no adsorption was observed at pH 5.5. The adsorption capacity of fraction I (M_v >100,000) exceeded that of fraction IV (M_v < 4,000) over the entire pH region used. No appreciable changes in the adsorbed amounts were observed after 24 hours.

Continuous flow dialysis techniques were used to determine the extent of binding between simazine and dissolved humic acids. It was observed that 50% and 60% of simazine added were thus removed from the dialysis bags containing humic acids fractions I and IV,respectively. Higher amounts of simazine were adsorbed by the high molecular weight humic fraction. The adsorption processes involve ionic bonds between simazine and humic acids. In addition it is likely that hydrogen bonds and physical forces are also involved in the adsorption of simazine by humic acids.     

水体中酮硝基麝香的臭氧氧化降解研究

采用臭氧氧化水体中的酮硝基麝香,考察pH、H2O2等因素对降解程度的影响,结果表明提高初始pH能加快酮硝基麝香的氧化降解,当pH为12时,反应时间1 h,酮硝基麝香几乎完全去除,浓度为2 mol/L和5 mol/L的H2O2存在有利于O3分解生成·OH自由基,使得酮硝基麝香的氧化降解速率加快,当H2O2浓度超过5 mol/L,H2O2会成为·OH的清除剂,降低·OH利用率;无论O3单独作用和O3/H2O2协同作用,酮硝基麝香降解符合准一级动力学规律;酮硝基麝香氧化降解产物包括甲酸、二乙酸和硝酸根等,其中硝基从苯环上脱落降低了硝基麝香对环境的风险.     

Atrazine removal by ozonation processes in surface waters

Atrazine (6-chloro-N-ethyl-N'-isopropyl-1,3,5-triazinedyl-2,4-diamine) was treated with ozone alone and in combination with hydrogen peroxide or UV radiation in three surface waters. Experiments were carried out in two bubble reactors operated continuously. Variables investigated were the ozone partial pressure, temperature, pH, mass flow ratio of oxidants fed: hydrogen peroxide and ozone and the type of oxidation including UV radiation alone. Residence time for the aqueous phase was kept at 10 min. Concentrations of some intermediates, including deethylatrazine, deisopropylatrazine and deethyldeisopropylatrazine, were also followed. The nature of water, specifically the alkalinity and pH were found to be important variables that affected atrazine (ATZ) removal. Surface waters with low alkalinity and high pH allowed the highest removal of ATZ to be reached. There was an optimum hydrogen peroxide to ozone mass flow ratio that resulted in the highest ATZ removal in each surface water treated. This optimum was above the theoretical stoichiometry of the process. Therefore, to reach the maximum removal of ATZ in a O3/H2O2 process, more hydrogen peroxide was needed in the surface waters treated than in ultrapure water under similar experimental conditions. In some cases, UV radiation alone resulted in the removal of ATZ higher than ozonation alone. This was likely due to the alkalinity of the surface water. Ozonation and UV radiation processes yield different amounts of hydrogen peroxide. Combined ozonations (O3/H2O2 and O3/UV) lead to ATZ removals higher than single ozonation or UV radiation but the formation of intermediates was higher.     

Recent progress on application of UV excilamps for degradation of organic pollutants and microbial inactivation

Excilamps as modern mercury-free sources of narrow-band UV radiation represent an attractive alternative in environmental applications. This review focuses on recent studies on the water and surface decontamination with excilamps by means of direct photolysis and advanced oxidation processes. To date, direct photolysis and advanced oxidation processes (AOPs) such as UV/H₂O₂, UV/Fenton and UV/O₃ have been applied for degradation of organic compounds (mainly, phenols, dyes and herbicides) in model aqueous solutions. Special emphasis is placed on studies combining UV irradiation (as a pre-treatment or post-treatment step) with biological treatment. In this review, the efficiencies of direct UV, UV/H₂O₂ and UV/TiO₂ processes for inactivation of a variety of pathogenic microorganisms in water and on surfaces are discussed. The analysis of the literature shows that more works need to be done on scaling up the processes, degradation/mineralization of target pollutant(s) in real effluents and evaluation of energy requirements.     

The importance of atmospheric ozone and hydrogen peroxide in oxidising sulphur dioxide in cloud and rainwater

The process by which sulphur dioxide is oxidised in atmospheric droplets has been studied in laboratory experiments designed to collect a large amount of chemical data pertinent to the atmospheric situation. Thus the oxidation of sodium sulphite solutions by oxygen, ozone and hydrogen peroxide has been studied at different pH's and temperatures. In all cases the reaction is first order with respect to sulphite ion but the order with respect to oxidant differs. For oxygen the order is zero whereas the order for ozone and hydrogen peroxide is one. Varying the hydrogen ion concentration has little effect on the oxygen reaction rate between pH 6 and 9; the ozone reaction rate is inversely proportional to the square root of the hydrogen ion concentration and the hydrogen peroxide rate is almost directly proportional to the hydrogen ion concentration. These last two observations are very important since in the case of ozone it indicates that the reaction proceeds via a free radical mechanism involving hydroxyl radicals and in the case of hydrogen peroxide it is the only oxidation process of sodium sulphite so far investigated that shows a positive response to the presence of hydrogen ions.The experimental data was used to calculate the rate of sulphate formation in water droplets under atmospheric conditions for each of the three oxidants. If it is assumed that the ozone and hydrogen peroxide gas phase concentrations are initially 50 parts in 10⁹ and 1 part in 10⁹ by volume respectively, then the rates of sulphate formation are equal in cloud water at pH 5.8. Above this pH the ozone reaction is faster and below it the hydrogen peroxide reaction is faster due to the positive catalysis by hydrogen ions; the oxygen rate is unimportant by comparison at all pH's below 7. The rate of hydrogen peroxide reaction is such that substantial amounts of sulphate can still be formed rapidly in water droplets at pH values from 3 to 5, and thus this process will be very important in creating acidity in rainwater.     

Modeling the quantum yields of herbicide 2,4-D decay in UV/H2O2 process

The photodecay of herbicide 2,4-D in a hydrogen peroxide-aided photolysis process was studied and modeled. The decay rate of 2,4-D was known to be low in the natural environment, but rate improvement was achieved in an H2O2/UV system. The 2,4-D decay quantum yields under ultraviolet (UV) light at 253.7 nm increased from 4.86 x 10(-6) to 1.30 x 10(-4) as the ratio of [H2O2]/[2,4-D] increased from 0.05 to 12.5. Apparently, in the presence of UV light, the decay rate of 2,4-D could be greatly improved as the concentration of hydrogen peroxide increased. However, the efficiency of 2,4-D photodecay was retarded if the concentration of H2O2 was overdosed, because the excess hydrogen peroxide consumes the hydroxyl radicals (HO*) in the solution, resulting in a much weaker oxidant HO2*. The decay of 2,4-D was also pH dependent. A ranking of acid (highest), base (middle) and neutral (lowest) was observed owing to the property change of reactants and the shifting of dominant mechanisms among photolysis, photohydrolysis and chemical oxidation. Two mathematical models were proposed to predict the quantum yield for various [H2O2]/[2,4-D] ratios and initial pH levels, in which very good correlation was found for the ranges of regular application.     

Photooxidation of methylhydroperoxide and ethylhydroperoxide in the aqueous phase under simulated cloud droplet conditions

The photooxidation of methylhydroperoxide (MHP) and ethylhydroperoxide (EHP) was studied in the aqueous phase under simulated cloud droplet conditions. The kinetics and the reaction products of direct photolysis and OH-oxidation were studied for both compounds. The photolysis frequencies obtained were J_MHP=4.5 (±1.0)×10⁻⁵ s⁻¹ and J_EHP=3.8 (±1.0)×10⁻⁵ s⁻¹ for MHP and EHP respectively at 6 °C. The rate constants of OH-oxidation of MHP at 6 °C were 6.3 (±2.6)×10⁸ M⁻¹ s⁻¹ and 5.8 (±1.9)×10⁸ M⁻¹ s⁻¹ relative to ethanol and 2-propanol respectively, and the rate constant of OH-oxidation of EHP was 2.1 (±0.6)×10⁹ M⁻¹ s⁻¹ relative to 2-propanol at 6 °C. The reaction products obtained were not only the corresponding aldehydes, but also the corresponding acids, and hydroxyhydroperoxides as primary reaction products. The yields for these products were sensitive to the pH value. The carbon balance was higher than 85% for all experiments, showing that most reaction products were detected. A chemical mechanism was proposed for each reaction, and the atmospheric implications were discussed.     

Degradation of ethylenethiourea pesticide metabolite from water by photocatalytic processes

In this study, photocatalytic (photo-Fenton and H₂O₂/UV) and dark Fenton processes were used to remove ethylenethiourea (ETU) from water. The experiments were conducted in a photo-reactor with an 80 W mercury vapor lamp. The mineralization of ETU was determined by total organic carbon analysis, and ETU degradation was qualitatively monitored by the reduction of UV absorbance at 232 nm. A higher mineralization efficiency was obtained by using the photo-peroxidation process (UV/H₂O₂). Approximately 77% of ETU was mineralized within 120 min of the reaction using [H₂O₂]₀ = 400 mg L^?1. The photo-Fenton process mineralized 70% of the ETU with [H₂O₂]₀ = 800 mg L^?1 and [Fe²⁺] = 400 mg L^?1, and there is evidence that hydrogen peroxide was the limiting reagent in the reaction because it was rapidly consumed. Moreover, increasing the concentration of H₂O₂ from 800 mg L^?1 to 1200 mg L^?1 did not enhance the degradation of ETU. Kinetics studies revealed that the pseudo-second-order model best fit the experimental conditions. The k values for the UV/H₂O₂ and photo-Fenton processes were determined to be 6.2 × 10^?4 mg L^?1 min^?1 and 7.7 × 10^?4 mg L^?1 min^?1, respectively. The mineralization of ETU in the absence of hydrogen peroxide has led to the conclusion that ETU transformation products are susceptible to photolysis by UV light. These are promising results for further research. The processes that were investigated can be used to remove pesticide metabolites from drinking water sources and wastewater in developing countries.     

Photo-Fenton-assisted ozonation of p-Coumaric acid in aqueous solution

The degradation of p-Coumaric acid present in olive oil mill wastewater was investigated as a pretreatment stage to obtain more easily biodegradable molecules, with lower toxicity that facilitates subsequent anaerobic digestion. Thus, photo-Fenton-assisted ozonation has been studied and compared with ozonation at alkaline pH and conventional single ultraviolet (UV) and acid ozonation treatments. In the combined process, the overall kinetic rate constant was split into various components: direct oxidation by UV light, direct oxidation by ozone and oxidation by hydroxyl radicals. Molecular and/or radical ozone reaction was studied by conducting the reaction in the presence and absence of tert-butylalcohol at pHs 2, 7 and 9. Ozone oxidation rate increases with pH or by the addition of Fenton reagent and/or UV radiation due to generation of hydroxyl radicals, *OH. Hydrogen peroxide and ferrous ion play a double role during oxidation since at low concentrations they act as initiators of hydroxyl radicals but at high concentrations they act as radical scavengers. Finally, the additional levels of degradation by formation of hydroxyl radicals have been quantified in comparison to the conventional single processes and an equation is proposed for the reaction rate as a function of studied operating variables.     

SIMAZINE REMOVAL FROM WATER IN A CONTINUOUS BUBBLE COLUMN BY O3 AND O3/H2O2

Simazine, [2-chloro, 4,6-bis(ethylamino)-1,3,5-s-triazine], a common herbicide found in surface and ground water has been ozonized in continuous flow mode. Typical operating variables in ozonation processes have been investigated. Thus, the ozone dose fed to the system exerted a positive effect, while the gas flow rate did not influence the efficiency of the process provided ozone mass flow rate was kept constant. Increasing the pH led to a higher extension of the free radical degradation of simazine and, therefore, to a higher efficiency of the process. Also, addition of free radical promoters, i.e. hydrogen peroxide, did result in a significant improvement of the simazine removal rate. A first approach to process economy showed the system ozone/hydrogen peroxide as the most advantageous in terms of electrical energy requirements.