Degradation of ethylenethiourea pesticide metabolite from water by photocatalytic processes

In this study, photocatalytic (photo-Fenton and H₂O₂/UV) and dark Fenton processes were used to remove ethylenethiourea (ETU) from water. The experiments were conducted in a photo-reactor with an 80 W mercury vapor lamp. The mineralization of ETU was determined by total organic carbon analysis, and ETU degradation was qualitatively monitored by the reduction of UV absorbance at 232 nm. A higher mineralization efficiency was obtained by using the photo-peroxidation process (UV/H₂O₂). Approximately 77% of ETU was mineralized within 120 min of the reaction using [H₂O₂]₀ = 400 mg L^?1. The photo-Fenton process mineralized 70% of the ETU with [H₂O₂]₀ = 800 mg L^?1 and [Fe²⁺] = 400 mg L^?1, and there is evidence that hydrogen peroxide was the limiting reagent in the reaction because it was rapidly consumed. Moreover, increasing the concentration of H₂O₂ from 800 mg L^?1 to 1200 mg L^?1 did not enhance the degradation of ETU. Kinetics studies revealed that the pseudo-second-order model best fit the experimental conditions. The k values for the UV/H₂O₂ and photo-Fenton processes were determined to be 6.2 × 10^?4 mg L^?1 min^?1 and 7.7 × 10^?4 mg L^?1 min^?1, respectively. The mineralization of ETU in the absence of hydrogen peroxide has led to the conclusion that ETU transformation products are susceptible to photolysis by UV light. These are promising results for further research. The processes that were investigated can be used to remove pesticide metabolites from drinking water sources and wastewater in developing countries.     

Rapid determination of polar pesticides and plant growth regulators in fruits and vegetables by liquid chromatography/tandem mass spectrometry

ABSTRACT

A simple high-throughput liquid chromatography/tandem mass spectrometry (LC-MS/MS) multiresidue analysis method was developed for the simultaneous determination of polar pesticides, plant growth regulators and other polar compounds. These included amitrole, chlormequat, mepiquat, cyromazine, ETU, PTU, perchlorate, and daminozide using a mixed-mode column. A 10 g test portion was shaken with acidified methanol for 10 min. After centrifugation, the sample extract was injected and analyzed within 11 min by LC-MS-MS. This column eliminated the need for derivatization or the use of ion paring reagent. Two MS-MS transitions were monitored in the method for each target compound to achieve true positive identification. Eight isotopically-labeled internal standards corresponding to each analyte were used to correct for matrix suppression effect and/or instrument signal drift. The average recovery for all analytes at 20, 40, and 250 ng/g (n = 6) ranged from 73–136%, with a relative standard deviation of ≤ 20%.     

Residues of EBDC fungicides and ETU in experimental and commercial beverages (beer and wine)

Residues of EBDC (ethylenebisdithiocarbamate) fungicides and ETU (ethylenethiourea; 2-imidazolidinethione) were monitored in beers and wines from different locations. No EBDC residues were detected in any of the samples examined. Concerning the ETU residues, the residue levels higher than the limit of method detection (0.01 ppm) were 22.6% and 7.3% in the commercial beer and wine samples respectively, but the number of samples containing more than 0.1 ppm of ETU was practically negligeable.     

The Wind-Frequency Allocation Method on Discharge Loading of Function Zones

Abstract

This paper introduces a new allocation method on discharge loading of each function zone in a total emission control region. The wind frequency, the position of each district, and the pollutant’s influence area were taken into account in this new method. The concept of “average downwind distance” was brought forward in this paper. The method here is more reasonable than the original method of area distribution, which was proposed by the “A-value” method in regulation of total emissions in China, by means of the simulation of annual average concentration in the total emission control region.     

Determination of glyphosate residue in maize and rice using a fast and easy method involving liquid chromatography–mass spectrometry (LC/MS/MS)

A fast and easy method was developed for the determination of glyphosate in maize and rice by using liquid chromatography triple quadrupole mass spectrometry with a Dionex Ion Pack column and phosphate buffer mobile phase. Samples were extracted with an acidified methanol solution. An isotope-labeled internal standard was added to the sample before extraction to ensure accurate tracking and quantification. The method’s performance was evaluated through a series of assessments to determine the accuracy, precision, linearity, matrix effect, limit of detection (LOD), and limit of quantification (LOQ). The mean recoveries for both matrices were within 70–105% at three fortification levels, including the LOQ. The precision for replicates was <20% (RSD%) for both matrices. Good linearity (R²=0.9982) was obtained over the concentration range of 0.01–1.5?mg kg^?1. The LOD was determined to be 0.002?mg kg^?1 for rice and 0.004?mg kg^?1 for maize. The LOQ was 0.01?mg kg^?1 for both maize and rice. Due to its versatility, the proposed method could be considered useful for the determination of glyphosate in cereals in routine analysis.     

Toxicity of new pyrethroid in pest insects Asciamonuste and Diaphania hyalinata,predator Solenopsis saevissima and stingless bee Tetragonisca angustula

There is increasing demand for new products for vegetable pest management. Thus, the aim of this study was to assess the toxicity of pyrethroids with acid moiety modifications to measure the insecticidal activity of these compounds on the lepidopteran vegetable pests Diaphania hyalinata (L.) (Lepidoptera: Pyralidae) and Asciamonuste (Latreille) (Lepidoptera: Pieridae) and evaluate their selectivity for the predatory ant Solenopsis saevissima (F. Smith) (Hymenoptera: Formicidae) and pollinator Tetragonisca angustula (Latreille) (Hymenoptera: Apidae: Meliponinae). Racemic mixtures of five new pyrethroids (30 µg molecule mg^?1 insect body weight) resulted in high (100%) and rapid (stable LD₅₀ after 12 h) mortality in D. hyalinata and A. monuste. In A. monuste, the trans-pyrethroid [12] isomer showed similar toxicity to permethrin. For D. hyalinata, the trans-pyrethroid [9] isomer and cis-pyrethroid [10] isomer were as toxic as permethrin. Due to their low selectivity, these new pyrethroids should be applied on the basis of ecological selectivity principles to minimize impacts on nontarget organisms S. saevissima and T. angustula.     

Combined PCDD/F Destruction and Particulate Control in a Baghouse: Experience with a Catalytic Filter System at a Medical Waste Incineration Plant

ABSTRACT

Phoenix Services, Inc., owns and operates the Baltimore Regional Medical Waste Incinerator in Baltimore, MD. New regulations for dioxins and furans imposed a limit that was considerably below historical emission levels. To determine a method to comply with the new dioxin/furan regulations, Phoenix Services performed trials with powdered activated carbon (PAC). Although the results with carbon were acceptable, Phoenix Services decided to replace their woven fiberglass filter bags with catalytic filters that simultaneously destroy dioxins and furans and collect particulate matter (PM). The catalytic filter system offered several advantages to Phoenix Services, including destruction of dioxins and furans instead of adsorption on carbon. The catalytic filters also offered a passive solution that did not require new carbon injection equipment. In January 2000, a campaign to measure dioxins/furans and PM was undertaken.     

Weighted road density: A simple way of assigning traffic-related air pollution exposure

BackgroundExisting traffic variables used for predicting NO₂ in epidemiological studies are either difficult to acquire or explain only a small proportion of the variance. The purpose of this study was to develop and validate a new predictor, weighted road density, which combines the maximum amount of information related to traffic into a single variable without the requirement of obtaining traffic counts for a given area.MethodTwo week NO₂ samples were collected using the readings of up to 32 passive samplers on 3 separate rounds between September and December 2006 and again in 2007. Several types of traffic related explanatory variables based on traffic counts, distance to main road and the proposed weighted road density were constructed using GIS software, and tested for association with the NO₂ samplers. Assessment of the best model was based on R² values, as well as leave-one-out cross validation.ResultsThe weighted road density variable and the density variable based on traffic counts resulted in a similar R² (0.59) for predicting NO₂, although weighted road density was much easier to construct and outperformed other variables such as distance to main road.ConclusionAs well as being a powerful predictor for use in a land use regression model, weighted road density can be used as a proxy for exposure to traffic-related pollution, for use in circumstances where direct measurements of pollutant levels are not feasible or are not required.     

The Plume Volume Molar Ratio Method for Determining NO2/NOx Ratios in Modeling—Part II: Evaluation Studies

ABSTRACT

A previous paper¹ discusses the methodology for a new method for deriving the nitrogen dioxide/nitrogen oxide (NO₂/NO_x) ratio in plumes that originally are composed mainly of (NO_x). It is called the Plume Volume Molar Ratio Method (PVMRM). This paper documents its performance against six different data sets. These performance evaluations show that the PVMRM can realistically predict the NO₂ fraction at close-in receptors yet still provide conservative estimates so that the air quality standards can be protected.     

Removal of SO2 from Simulated Flue Gases Using Non-Thermal Plasma-Based Microgap Discharge

Abstract

The removal of sulfur dioxide (SO₂) from simulated flue gases streams (N₂/O₂/H₂O/SO₂) was experimentally investigated using microgap discharge. In the experiment, the thinner dielectric layers of aluminum oxide (Al₂O₃) were used to form the microgap discharge. With this physical method, a high concentration of hydroxyl (OH·) radicals were produced using the ionization of O₂ and H₂O to further the conversion of SO₂ into sulfuric acid (H₂SO₄) at 120° C in the absence of any catalysts and absorbents, which were captured with the electrostatic precipitator (ESP). As a result, the increase of discharge power and concentrations of O₂ and H₂O increased the production of OH· radicals resulting in enhanced removal of SO₂ from gas streams. With the test and analysis, a number of H₂SO₄ droplets were produced in experiment. Therefore, a new method for removal of SO₂ in semidry method without ammonia (NH₃) additive was found.     

Authors’ Reply

ABSTRACT

Exposures of occupants in school buses to on-road vehicle emissions, including emissions from the bus itself, can be substantially greater than those in outdoor settings. A dual tracer method was developed and applied to two school buses in Seattle in 2005 to quantify in-cabin fine particulate matter (PM_2.5) concentrations attributable to the buses' diesel engine tailpipe (DPM_tp) and crankcase vent (PM_ck) emissions. The new method avoids the problem of differentiating bus emissions from chemically identical emissions of other vehicles by using a fuel-based organometallic iridium tracer for engine exhaust and by adding deuterated hexatriacontane to engine oil. Source testing results showed consistent PM:tracer ratios for the primary tracer for each type of emissions. Comparisons of the PM:tracer ratios indicated that there was a small amount of unburned lubricating oil emitted from the tailpipe; however, virtually no diesel fuel combustion products were found in the crankcase emissions. For the limited testing conducted here, although PM_ck emission rates (averages of 0.028 and 0.099 g/km for the two buses) were lower than those from the tailpipe (0.18 and 0.14 g/km), in-cabin PM_ck concentrations averaging 6.8 μg/m³ were higher than DPM_tp (0.91 μg/m³ average). In-cabin DPM_tp and PM_ck concentrations were significantly higher with bus windows closed (1.4 and 12 μg/m³, respectively) as compared with open (0.44 and 1.3 μg/m³, respectively). For comparison, average closed- and open-window in-cabin total PM_2.5 concentrations were 26 and 12 μg/m³, respectively. Despite the relatively short in-cabin sampling times, very high sensitivities were achieved, with detection limits of 0.002 μg/m³ for DPM_tp and 0.05 μg/m³ for PM_ck.

IMPLICATIONS PM_2.5 measurements in two Seattle school buses showed average concentrations of 26 and 12 μg/m³ with windows closed and open, respectively. Virtually all PM_2.5 was car bonaceous. Tracer measurements showed that bus self-pollution contributed approximately 50% of total PM_2.5 concentrations with windows closed and 15% with windows open, with over three-quarters of these contributions attributed to crankcase emissions. Maintaining ventilation in buses clearly reduces total PM_2.5 exposures and that from the buses' own emissions. The dual tracer method now offers researchers a new technique for explicit identification of single source contributions in settings with multiple sources of carbonaceous emissions.     

Selection and Substantiation of an Organic Solvent Removal Apparatus at a Print Shop by Comparative Experiments Using the Activated Carbon Adsorption and Catalytic Oxidation Methods

ABSTRACT

The investigation of an appropriate organic solvent removal apparatus for installation in a newly reconstructed print shop as a countermeasure for preventing the exhaust of organic solvents was conducted.

The selection of an organic solvent removal apparatus was made after bench-scale tests of the activated carbon adsorption method and the catalytic oxidation method, both of which are effective for the removal of organic solvents, were performed on the actual exhaust gas at the print shop. The results showed that both methods were efficient enough to be applied to the removal of organic solvents, but the activated carbon adsorption method had many drawbacks, such as the need for frequent replacement of activated carbon and complex maintenance. For the catalytic oxidation method, running costs are high, but there are many merits, such as that the catalysts do not have to be replaced as often and maintenance is simple. After considering these factors, a catalytic oxidation removal apparatus was installed at the new print shop. In the results of the substantiation test on the actual apparatus using mixed catalysts of platinum and manganese plus copper, the removal efficiency was 97.998.7% and the concentration of the outlet exhaust gas was about 10 ppm (the average concentration of the inlet exhaust gas was 528 ppm) at a space velocity of 30,000 hr^-1 and a reaction temperature of 200 °C. The results of this study were substantiated.     

Measuring Concentrations of Volatile Organic Compounds in Vinyl Flooring

ABSTRACT

The initial solid-phase concentration of volatile organic compounds (VOCs) is a key parameter influencing the emission characteristics of many indoor materials. Solid-phase measurements are typically made using solvent extraction or thermal headspace analysis. The high temperatures and chemical solvents associated with these methods can modify the physical structure of polymeric materials and, consequently, affect mass transfer characteristics.

To measure solid-phase concentrations under conditions resembling those in which the material would be installed in an indoor environment, a new technique was developed for measuring VOC concentrations in vinyl flooring (VF) and similar materials. A 0.09-m² section of new VF was punched randomly to produce ~200 0.78-cm² disks. The disks were milled to a powder at -140 °C to simultaneously homogenize the material and reduce the diffusion path length without loss of VOCs. VOCs were extracted from the VF particles at room temperature by fluidized-bed desorption (FBD) and by direct thermal desorption (DTD) at elevated temperatures. The VOCs in the extraction gas from FBD and DTD were collected on sorbent tubes and analyzed by gas chromatog-raphy/mass spectrometry (GC/MS). Seven VOCs emitted by VF were quantified. Concentration measurements by FBD ranged from 5.1 |ig/g VF for n-hexadecane to 130 |Jg/g VF for phenol. Concentrations measured by DTD were higher than concentrations measured by FBD. Differences between FBD and DTD results may be explained using free-volume and dual-mobility sorption theory, but further research is necessary to more completely characterize the complex nature of a diffusant in a polymer matrix.     

Degradation of tris(1-chloro-2-propanyl) phosphate by the synergistic effect of persulfate and zero-valent iron during a mechanochemical process

This study revealed a dual pathway for the degradation of tris(1-chloro-2-propanyl) phosphate (TCPP) by zero-valent iron (ZVI) and persulfate as co-milling agents in a mechanochemical (MC) process. Persulfate was activated with ZVI to degrade TCPP in a planetary ball mill. After milling for 2 h, 96.5% of the TCPP was degraded with the release of 63.16, 50.39, and 42.01% of the Cl^?, SO₄^2?, and PO₄^3?, respectively. In the first degradation pathway, persulfate was activated with ZVI to produce hydroxyl (·OH) radicals, and ZVI is oxidized to Fe(II) and Fe(III). A substitution reaction occurred as a result of the attack of ·OH on the P–O–C bonds, leading to the successive breakage of the three P–O–C bonds in TCPP to produce PO₄^3?. In the second pathway, a C–Cl bond in part of the TCPP molecule was oxidized by SO₄·^? to carbonyl and carboxyl groups. The P–O–C bonds continued to react with ·OH to produce PO₄^3?. Finally, the intermediate organochloride products were further reductively dechlorinated by ZVI. However, the synergistic effect of the oxidation (·OH and SO₄·^?) and the reduction reaction (ZVI) did not completely degrade TCPP to CO₂, resulting in a low mineralization rate (35.87%). Moreover, the intermediate products still showed the toxicities in LD₅₀ and developmental toxicant. In addition, the method was applied for the degradation of TCPP in soil, and high degradations (>?83.83%) were achieved in different types of soils.

     

The Plume Volume Molar Ratio Method for Determining NO2/NOx Ratios in Modeling—Part I: Methodology

ABSTRACT

During New Source Review modeling of proposed major sources of oxides of nitrogen (NO_x), maximum impacts are often predicted to occur very close to the source. At the same time, current modeling guidance recommends techniques that may be overly conservative in estimating the fraction of nitrogen dioxide (NO₂) in these plumes. A new technique called the Plume Volume Molar Ratio Method (PVMRM) is being proposed that simulates both chemistry and dispersion to better estimate the fraction of NO₂. This paper documents the methodology behind the technique. A follow-up pa-per¹ will evaluate its performance against a number of databases. This method is designed to realistically predict NO₂ fraction at close-in receptors yet still provide conservative estimates so that the air quality standards can be protected.     

Tank Atmosphere Perturbation: A Procedure for Assessing Flashing Losses from Oil Storage Tanks

Abstract

A new procedure to measure the total volume of emissions from heavy crude oil storage tanks is described. Tank flashing losses, which are difficult to measure, can be determined by correcting this value for working and breathing losses. The procedure uses a fan or blower to vent the headspace of the storage tank, with subsequent monitoring of the change in concentrations of oxygen or other gases. Combined with a separate determination of the reactive organic carbon (ROC) fraction in the gas, this method allows the evaluation of the total amount of ROC emitted. The operation of the system is described, and results from measurement of several storage tanks in California oil fields are presented. Our measurements are compared with those obtained using the California Air Resources Board (CARB) 150 method.     

Analytical methods for the determination of alachlor,metolachlor, simazine and atrazine mobility in soils

Abstract

A method for the determination of the mobility of the herbicides, alachlor, metolachlor, simazine and atrazine in soil is described . The method is based on the use of soil thin‐layer chromatography (TLC) and does not require the use of radiolabelled compounds. Soil on the TLC plate after development was separated into various bands, the material in each band was extracted with solvents and analyzed by gas chromatography.     

Estimating the Lower Heating Values of Hazardous and Solid Wastes

ABSTRACT

A new equation is proposed to predict the lower heating value of hazardous and non-hazardous materials. The equation was developed by a statistical correlation of heating value and composition data for a variety of materials as reported in a number of sources. The model takes into account the carbon, hydrogen, oxygen, chlorine, and sulfur content of the material being combusted.     

A Portable Fiber-Optic Chemical Device for the Quantitative Determination of Carbon Monoxide from Automobile Exhaust Emissions

ABSTRACT

A colorimetxic method for the quantitative determination of CO by diffuse reflectance is described. This method is based on the reduction by CO of Mo (VI) from the indicator reagent molybdosilicic acid (H₈Si[Mo₂O₇]₆). The reduction yielded a change of color from clear yellow to dark green on white disk filter chart paper wetted with reagent indicator solution. The gaseous mixture containing CO was forced to pass through this chart paper, initiating the reaction. The intensity of the color produced, measured by diffuse reflectance, was proportional to the CO concentration present in exhaust gases in the range from 0.02 to 12% volume/volume (v/v). A 650-nm light-emitting diode was used as a light source. A two-fiber-optic system carried the light from the source to the detection system, which was composed of a photodiode, an amplification circuit, and a digital display. The method was applied with success in field measurements for automobiles in the Otto cycle. In a previous paper, this method was used for the quantitative determination of exhaust emissions from diesel-fueled vehicles.¹     

The synthetic pyrethroid isomers I. Preparation

Abstract

Enantiomers and racemic mixtures of selected benzilic esters using resolved and raceme permethrinic or chrysanthemic acids of high purity were synthesised via improved methods based on conventional steps. Nine basic structures of selected derivatives having hydrogen, bromo or phenoxy group at meta position were prepared including the well known insecticides of phenothrin, permethrin and cypermethrin. The optical purity of these compounds were determined via an NMR method applying chiral shift reagents. The configuration of the isomers of new a‐cyano‐benzyl esters were assigned via a rule realized by comparing the characteristic 1H NMR shifts of the dimethyl groups attached to the cyclopropane ring.