Soil pH and Anion Abundance Affects on Copper Adsorption

Abstract

Copper (Cu) input to agricultural soils results from Cu containing pesticides and/or that in soil amendments, such as manure or sewage sludge. Soil and soil solution properties influence the adsorption and desorption of Cu by the soil, which in turn determines its plant availability and/or phytotoxicities. Effects of different anion enrichment in the equilibrium solution on Cu adsorption by different soils (pH range of 6.2–9.9) were investigated in this study over a range of Cu concentrations. With Cu concentrations in the range of 0–100 mg L^?1 in the equilibration solution, 95–99% of applied Cu was adsorbed by all three soils. The adsorption of Cu was similar regardless of using either 0.01 M CaCl₂ or Ca(NO₃)₂ as the equilibration solution. When the Cu concentration in the equilibration solution was further increased in the range of 500–2000 mg L^?1, the adsorption of Cu decreased from 60 to 24% of applied Cu in two soils with pH 6.2–7.9. In a high pH soil (pH = 9.9), the Cu adsorption decreased from 77 to 34%. Addition of incinerated sewage sludge (ISS) to a Palouse silt loam soil (pH = 6.2) increased the Cu adsorption as compared to that by unamended soil. This was, in part, due to an increase in the soil suspension pH with ISS amendment.     

Soil pH and anion abundance affects on copper adsorption

Copper (Cu) input to agricultural soils results from Cu containing pesticides and or that in soil amendments, such as manure or sewage sludge. Soil and soil solution properties influence the adsorption and desorption of Cu by the soil, which in turn determines its plant availability and/or phytotoxicities. Effects of different anion enrichment in the equilibrium solution on Cu adsorption by different soils (pH range of 6.2-9.9) were investigated in this study over a range of Cu concentrations. With Cu concentrations in the range of 0-100 mg L(-1) in the equilibration solution, 95-99% of applied Cu was adsorbed by all three soils. The adsorption of Cu was similar regardless of using either 0.01 M CaCl2 or Ca(NO3)2 as the equilibration solution. When the Cu concentration in the equilibration solution was further increased in the range of 500-2000 mg L(-1), the adsorption of Cu decreased from 60 to 24% of applied Cu in two soils with pH 6.2-7.9. In a high pH soil (pH=9.9), the Cu adsorption decreased from 77 to 34%. Addition of incinerated sewage sludge (ISS) to a Palouse silt loam soil (pH = 6.2) increased the Cu adsorption as compared to that by unamended soil. This was, in part, due to an increase in the soil suspension pH with ISS amendment.     

Adsorption/Desorption of Copper by a Sandy Soil Amended with Various Rates of Manure,Sewage Sludge,and Incinerated Sewage Sludge

Organic amendments are sometimes applied to agricultural soils to improve the physical, chemical, and microbiological properties of the soils. The organic fractions in these soil amendments also influence metal reaction, particularly the adsorption and desorption of metals, which, in turn, determine the bioavailability of the metals and hence their phytotoxicities. In this study, a Quincy fine sandy (mixed, mesic, Xeric Torripsamments) soil was treated with 0 to 160 g kg^?1 rates of either manure, sewage sludge (SS), or incinerated sewage sludge (ISS) and equilibrated in a greenhouse at near field capacity moisture content for 100 days. Following the incubation period, the soil was dried and adsorption of copper (Cu) was evaluated in a batch equilibration study at either 0, 100, 200, or 400 mg L^?1 Cu concentrations in a 0.01M CaCl₂ solution. The desorption of adsorbed Cu was evaluated by three successive elutions in 0.01M CaCl₂. Copper adsorption increased with an increase in manure rates. At the highest rate of manure addition (160 g kg^?1 soil), Cu adsorption was two-fold greater than that by the unamended soil at all rates of Cu additions. With increasing rates of Cu additions, the adsorption of Cu decreased from 99.4 to 77.6% of Cu applied to the 160 g kg^?1 manure amended soil. The desorption of Cu decreased with an increase in rate of manure amendment. Effects of sewage sludge amendments on Cu adsorption were somewhat similar to those as described for manure additions. Likewise, the desorption of Cu was the least at the high rate of SS addition (160 g kg^?1), although at the lower rates there was not a clear indication of the rate effects. In contrast to the above two amendments, the ISS amendment had the least effect on Cu adsorption. At the highest rate of ISS amendment, the Cu adsorption was roughly 50% of that at the similar rate of either manure or SS amendments, across all Cu rates.     

毒死蜱在不同土壤腐殖酸上的吸附/解吸特征

通过平衡振荡法研究毒死蜱在不同来源土壤腐殖酸(Has)上的吸附/解吸行为.结果表明,毒死蜱在Has上的等温吸附行为用Freundlich模型描述相对更合理;它们的吸附等温线在实验范围内基本呈直线,且吸附能力很强,顺序为:紫色潮土Has＞黄壤Has＞中性紫色土Has＞酸性紫色土Has＞腐殖土Has;但毒死蜱的解吸率较小,其值均小于26.70%,有明显的滞后现象,尤其是腐殖土Has和紫色潮土Has,固定能力顺序为:紫色潮土Has＞腐殖土Has＞中性紫色土Has＞酸性紫色土Has＞黄壤Has.由于不同来源土壤中Has的组成结构差异明显,它们对毒死蜱的吸附/解吸规律表现出不同的特征.土壤Has对毒死蜱的吸附/解吸行为的影响是多种因素综合作用的结果,具体作用机理尚待进一步研究.     

Desorption of cadmium from goethite: effects of pH, temperature and aging

Cadmium is perhaps environmentally the most significant heavy metal in soils. Bioavailability, remobilization and fate of Cd entering in soils are usually controlled by adsorption-desorption reactions on Fe oxides. Adsorption of Cd on soil colloids including Fe oxides has been extensively studied but Cd desorption from such soil minerals has received relatively little attention. Some factors that affect Cd adsorption on goethite include pH, temperature, aging, type of index cations, Cd concentrations, solution ionic strength and presence of organic and inorganic ions. This research was conducted to study the influence of pH, temperature and aging on Cd desorption from goethite. Batch experiments were conducted to evaluate Cd desorption from goethite with 0.01 M Ca(NO3)2. In these experiments Cd desorption was observed at 20, 40 and 70 degrees C in combination with aging for 16 h, 30, 90 and 180 d from goethite that adsorbed Cd from solutions containing initial Cd concentrations of 20, 80 and 180 microM. Following the adsorption step Cd desorption was measured by 15 successive desorptions after aging at various temperatures. At the lowest amount of initially adsorbed Cd and equilibrium pH 5.5, cumulative Cd desorption decreased from 71% to 17% with aging from 16 h to 180 d and the corresponding decrease at equilibrium pH 6.0 was from 32% to 3%. There was a substantial decrease in Cd desorption with increasing equilibration temperature. For example, in goethite with the lowest amount of initial adsorption at equilibrium pH 5.5, cumulative Cd desorption decreased from 71% to 31% with increase in temperature from 20 to 70 degrees C, even after 16 h. Dissolution of Cd adsorbed goethite in 1M HCl, after 15 successive desorptions with 0.01 M Ca(NO3)2, indicated that approximately 60% of the Cd was surface adsorbed. Overall, dissolution kinetics data revealed that 23% to 88% Cd could not be desorbed, which could possibly be diffused into the cracks and got entrapped in goethite crystals. At elevated temperature increased equilibrium solution pH favoured the formation of CaCO3 and CdCO3 which reasonably decreased Cd desorption. Cadmium speciation showed the formation of calcite and otavite minerals at 40 and 70 degrees C due to increase in pH (>9.5) during aging. X-ray diffraction analysis (XRD) of these samples also revealed the formation of CaCO3 at elevated temperatures with aging. While mechanisms such as Cd diffusion and/or entrapment into fissures and cracks in goethite structure with increase in temperature and aging are possible.     

Adsorption behavior of reactive dye in aqueous solution on chemical cross-linked chitosan beads

A batch system was applied to study the adsorption of reactive dye (reactive red 189) from aqueous solutions by cross-linked chitosan beads. The ionic cross-linking reagent sodium tripolyphosphate was used to obtain more rigid chitosan beads. To stabilize chitosan in acid solutions, chemical cross-linking reagent epichlorohydrin (ECH), glutaraldehyde and ethylene glycol diglycidyl ether was used and ECH shows a higher adsorption capacity. The Langmuir and Freundlich adsorption models were applied to describe the equilibrium isotherms at different particle sizes and isotherm constants were determined. The Langmuir model agrees very well with experimental data and its calculated maximum monolayer adsorption capacity has very large value of 1802-1840 (g/kg) at pH 3.0, 30 degrees C. The kinetics of the adsorption with respect to the initial dye concentration, temperature, pH, ionic strength, and wet/dry beads were investigated. The pseudo-first-order, second-order kinetic models and intraparticle diffusion model were used to describe the kinetic data and the rate constants were evaluated. The dynamical data fit well with the second-order kinetic model, except for the dry beads fitting better with the first-order model. The adsorption capacity increases largely with decreasing solution pH or with increasing initial dye concentration. Thermodynamic parameters such as change in free energy (deltaG(0)), enthalpy (deltaH(0)), entropy (deltaS(0)) and activation energy were also determined. The adsorption mechanism is shown to be the electrostatic interactions between the dye and chitosan beads. The desorption data shows that the removal percent of dye RR 189 from the cross-linked chitosan beads is 63% in NaOH solutions at pH 10.0, 30 degrees C. The desorbed chitosan beads can be reused to adsorb the dye and to reach the same capacity as that before desorption.     

Adsorption behavior of RH‐5992 insecticide onto sandy and clay loam forest soils

Abstract

Adsorption‐desorption behavior of RH‐5992 [Mimic®, N'‐t‐butyl‐N'‐(3,5‐dimethylbenzoyl)‐N‐(4‐ethylbenzoyl) hydrazine] in sandy and clay loam forest soils was studied using the batch equilibrium method. Adsorption was higher in the clay loam soil than in the sandy loam, and increased linearly with RH‐5992 concentration, but decreased with increasing pH and temperature. The adsorption data fit better to the Freundlich, than to the Langmuir equation. The K_D (linear adsorption constant) and K_F (Freundlich constant) were similar for each soil at 5, 15 and 25°C and decreased with increase of temperature, indicating that the enthalpy of adsorption was negative. The exponent of the Freundlich equation was close to unity for both soils at all three temperatures. The low E_a (energy of activation) indicated a diffusion‐controlled process during the initial stages of adsorption. The desorption isotherm differed from that of adsorption, and the linear desorption constant, K_D(d), was ca 25 times higher than the K_D, indicating that adsorption of RH‐5992 was not readily reversible. Evaluation of thermo‐dynamic parameters confirmed the presence of strong bonds between the solute and soil. These findings suggest that RH‐5992 has a limited potential for downward mobility leading to groundwater contamination.     

Adsorption/desorption of copper by a sandy soil amended with various rates of manure, sewage sludge, and incinerated sewage sludge

Organic amendments are sometimes applied to agricultural soils to improve the physical, chemical, and microbiological properties of the soils. The organic fractions in these soil amendments also influence metal reaction, particularly the adsorption and desorption of metals, which, in turn, determine the bioavailability of the metals and hence their phytotoxicities. In this study, a Quincy fine sandy (mixed, mesic, Xeric Torripsamments) soil was treated with 0 to 160 g kg(-1) rates of either manure, sewage sludge (SS), or incinerated sewage sludge (ISS) and equilibrated in a greenhouse at near field capacity moisture content for 100 days. Following the incubation period, the soil was dried and adsorption of copper (Cu) was evaluated in a batch equilibration study at either 0, 100, 200, or 400 mg L(-1) Cu concentrations in a 0.01M CaCl2 solution. The desorption of adsorbed Cu was evaluated by three successive elutions in 0.01M CaCl2. Copper adsorption increased with an increase in manure rates. At the highest rate of manure addition (160 g kg(-1) soil), Cu adsorption was two-fold greater than that by the unamended soil at all rates of Cu additions. With increasing rates of Cu additions, the adsorption of Cu decreased from 99.4 to 77.6% of Cu applied to the 160 g kg(-1) manure amended soil. The desorption of Cu decreased with an increase in rate of manure amendment. Effects of sewage sludge amendments on Cu adsorption were somewhat similar to those as described for manure additions. Likewise, the desorption of Cu was the least at the high rate of SS addition (160 g kg(-1)), although at the lower rates there was not a clear indication of the rate effects. In contrast to the above two amendments, the ISS amendment had the least effect on Cu adsorption. At the highest rate of ISS amendment, the Cu adsorption was roughly 50% of that at the similar rate of either manure or SS amendments, across all Cu rates.     

Appendix

Abstract

The interaction of glyphosate [N‐(phosphonomethyl)‐glycine] with four typical European soils is reported. Results of adsorption and desorption isotherms show that the interaction of glyphosate with these soils was mainly related to content of iron and aluminium amorphus hydroxides. Moreover, it was found that the presence of divalent cations in 2: 1 clay minerals also contribute to glyphosate adsorption. The S‐type form of the adsorption isotherms revealed the existence of two different binding sites. These were exchangeable cations at low herbicide concentration and Fe and Al at higher glyphosate concentrations. The K maximum values of adsorption provided by the linear form of the Langmuir equation were found to be more consistent with soil parameters than those calculated by the Freundlich equation. The order of desorption from the soils was the reverse of that found for adsorption. Moreover, desorption varied from around 15 to 80% of the adsorbed herbicide according to the soil characteristics. This indicated that glyphosate adsorption on soils is far from being permanent and leaching to lower soil horizons with limited biological activity may occur.     

Sorption behavior of a new acidic herbicide in soils

The sorptive behavior of the experimental herbicide quinmerac (7-chloro-3-methyl-quinoline-8-carboxylic acid) was investigated in soils of different organic carbon content. Distribution coefficients are low (K_d = 0.03 - 12 mL g⁻¹) and are mainly determined by the soil organic carbon content. The adsorption mechanism operating in neutral to slightly acid agricultural soils is supposed to be cation bridging with the anionic form of quinmerac. Under acid conditions (pH 5.2) the predominating sorption mechanism is hydrophobic interaction. Therefore soil pH and cationic composition are also major factors determining the sorptive capacity of soils for quinmerac.

Adsorption kinetics, equilibrium adsorption and desorption isotherms were determined in batch experiments. Sorption kinetics were investigated at various times from 15 min to 96 hours. A two-step sorption behavior with time was found for the anionic form indicating two types of sorption mechanisms or sorption sites. Equilibrium for the first type was reached at a time-scale of minutes and for the second type after 24 hours. Adsorption isotherms were determined for two soil/solution ratios 1/5 and 1/3. Alteration of the adsorbent concentration exerted a strong influence on the adsorption isotherms. An increase of sorption was found with increasing adsorbent concentration. Under natural soil conditions sorption is therefore expected to be higher compared to the batch experiments. Desorption isotherms were obtained using the consecutive desorption method. Desorption hysteresis was not observed which indicates weak interactions. Implications of the results for the movement of quinmerac under field conditions and for models describing transport are discussed.     

弱碱性树脂吸附-解吸苦味酸

考察了水中苦味酸在弱碱性离子交换树脂D301R上的吸附与解吸。研究了吸附热力学、动力学特性及吸附机理。结果表明,树脂在pH=2.7～10.2时,吸附能力最好。等温平衡吸附遵循Freundlich模型。吸附过程为吸热、熵增的自发过程。吸附动力学符合Lagergren准二级速率方程,颗粒内扩散为吸附速率的主要控制步骤,吸附速率常数为7.23×10-5～1.20×10-4g/(mg.min),吸附活化能为19.4 kJ/mol。树脂上吸附的苦味酸可用HNO3+丙酮混合液定量洗脱,洗脱率达99%。静态吸附和脱附的比较结果证实了吸附过程中存在不可逆化学吸附。树脂对苦味酸的吸附主要是通过静电吸附、酸碱络合吸附、氢键吸附等协同作用来完成的。     

Fate and mobility of pharmaceuticals in solid matrices

The sorption and mobility of six pharmaceuticals were investigated in two soil types with different organic carbon and clay content, and in bacterial biomass (aerobic and anaerobic). The pharmaceuticals examined were carbamazepine, propranolol, diclofenac sodium, clofibric acid, sulfamethoxazole and ofloxacin. The sorption experiments were performed according to the OECD test Guideline 106. The distribution coefficients determined by this batch equilibrium method varied with the pharmaceutical tested and the solid matrix type. Ofloxacin was particularly strongly adsorbed (except of the case of using anaerobic biomass for the solid matrix) while clofibric acid was found to be weakly adsorbed. The fate of pharmaceuticals in soil was also assessed using lysimeters. Important parameters that were studied were: the pharmaceutical loading rate and the hydraulic loading rate for adsorption and the rate and duration of a "rain" event for desorption. Major differences in the mobility of the six pharmaceuticals were observed and correlated with the adsorption/desorption properties of the compounds.     

Adsorption Characteristics of Activated Carbon and XAD4 Resin for the Removal of Hazardous Organic Solvents

A comparative study has been conducted on adsorption/desorption of six hazardous organic vapors on synthetic resin (XAD4) and activated carbon, using a differential reactor involving the expansion of a quartz spring. While both sorbents can effectively remove the organic vapors, it was observed that at low concentrations activated carbon adsorbed more organic vapor than synthetic resin. At higher, industrial concentrations, the resins adsorbed more vapor as demonstrated by the slopes of the equilibrium isotherms. The resin also showed much higher desorptlon.

The effective Intraparticle diffusion coefficients (D_e) were observed to be strongly dependent on solute concentration. Pore diffusion dominated the adsorption/desorption of the six organic vapors on XAD4 resin. For the carbon system, pore diffusion dominated the adsorption but surface diffusion contributed to the desorptlon process. This is believed to be due to higher Interaction of the adsorbates with activated carbon.     

Modeling VOCs adsorption onto activated carbon

The activated carbon adsorption process is affected by the characteristics of adsorbent, adsorbate and environmental conditions. In this study, both adsorption and desorption processes are assumed to occur simultaneously and a numerical model was developed with a non-linear driving force in conjunction with the Langmuir model for predicting the overall adsorption process. The numerical model provides both adsorption and desorption rate constants and activation energies. The resultant equilibrium constants are of the same order of magnitude as reported by other studies. Results show that the model could well predict the adsorption isotherms and breakthrough curves under various conditions.     

The removal of reactive black 5 from aqueous solutions by cotton seed shell

This study investigated the removal of Reactive Black 5 (RB5) textile dye from aqueous solutions using cotton (Gossypium hirsutum) seed shell (CSS) as low cost adsorbents. The data were described according to the Freundlich and Langmuir isotherm models. Of these, the Langmuir model provided the best fit for the experimental data. The highest measured adsorption density was 12.19 mg/g at pH 2. An equilibrium adsorption rate of RB5 by CSS (q(e) = 11.879 mg/g) was observed at 30 minutes. In order to evaluate the adsorption kinetic mechanisms, pseudo first and second order rate kinetic models and an intraparticle diffusion model were applied, with the pseudo second order model providing an excellent fit for the data.     

Adsorption and desorption processes of MCPA in Polish mineral soils

Studies on the adsorption and desorption of MCPA (4-chloro-2-methylophenoxyacetic acid) were performed in soil horizons of three representative Polish agricultural soils. The Hyperdystric Arenosol, the Haplic Luvisol and the Hypereutric Cambisol were investigated in laboratory batch experiments. Initially, both the adsorption and desorption proceeded rapidly, and either the equilibrium was reached after approximately 30 min or the process slowed down and continued at a slow rate. In the latter case, the equilibrium was reached after 8 hours. Data on the adsorption/desorption kinetics fitted well to the two-site kinetic model. The measured sorption and desorption isotherms were of L-type. The sorption distribution coefficients (K(ads) (d)) were in the range of 0.75--0.97 for Ap soil horizons and significantly lower in deeper soil layers. The corresponding desorption coefficients (K(des) (d)) were higher and ranged from 1.02 to 2.01. Both the adsorption and desorption of MCPA in all soil horizons was strongly and negatively related to soil pH. It appears that hydrophobic sorption plays a dominant role in the MCPA retention in topsoils whereas hydrophilic sorption of MCPA anions is the dominant adsorption mechanism in subsoils.     

Sorption of atrazine and metolachlor by earthworm surface castings and soil

Abstract

Atrazine and metolachlor were more strongly retained on earthworm (Lumbricus terrestris L.) castings than on soil, suggesting that earthworm castings at the surface or at depth can reduce herbicide movement in soil. Herbicide sorption by castings was related to the food source available to the earthworms. Both atrazine and metolachlor sorption increased with increasing organic carbon (C) content in castings, and Freundlich constants (K_f values) generally decreased in the order: soybean‐fed > corn‐fed > not‐fed‐earthworm‐castings. The amount of atrazine or metolachlor sorbed per unit organic carbon (K_oc values) was significantly greater for corn‐castings compared with other castings, or soil, suggesting that the composition of organic matter in castings is also an important factor in determining the retention of herbicides in soils. Herbicide desorption was dependent on both the initial herbicide concentration, and the type of absorbent. At small equilibrium herbicide concentrations, atrazine desorption was significantly greater from soil than from any of the three casting treatments. At large equilibrium herbicide concentrations, however, the greater organic C content in castings had no significant effect on atrazine desorption, relative to soil. For metolachlor, regardless of the equilibrium herbicide concentration, desorption from soybean‐ and corn‐castings treatments was always less than desorption from soil and not‐fed earthworm castings treatments. The results of this study indicate that, under field conditions, the extent of herbicide retention on earthworm castings will tend to be related to crop and crop residue management practices.     

Desorption kinetics of neutral hydrophobic organic compounds from field-contaminated sediment

The chemical release rates from a field-contaminated sediment (Lake Charles, LA) using Tenax desorption were studied. Two dichlorobenzenes (m-, p-), hexachlorobutadiene, and hexachlorobenzene were investigated. Contrary to reports that sorption rates are inversely related to K(OW), the slow desorption rates were found to be similar for the four compounds. The data were modeled by a two-compartment irreversible adsorption and radial diffusion model. Desorption kinetics from the first irreversible compartment can be modeled by radial diffusion and assume an irreversible adsorption constant and soil tortuosity of 4.3. The desorption half-life is approximately 2-7 days. Desorption from the second irreversible compartment is very slow (half-life of approximately 0.32-8.62 years) presumably caused by entrapment in soil organic matter that increases the constrictivity of the solid phase to chemical diffusion. From the kinetic data, it is deduced that the diffusion pore diameter of the second irreversible compartment is approximately equal to the critical molecular diameter. The mass of chemicals in this highly constrictive irreversible compartment is approximately one-fourth of the maximum irreversible, or resistant, compartment. The slow kinetics observed in this study add additional support to the notion that the irreversibly sorbed chemicals are 'benign' to the environment.     

Kinetics of endosulfan sorption on to wood charcoal

Abstract

A part of the research work conducted to evaluate the efficiency of a locally available low cost wood charcoal in removing endosulfan, an organochlorine insecticide, has been presented here in this paper. In the batch experiments conducted at 1 mg/I initial concentration of endosulfan, it was found that wood charcoal could remove endosulfan from water up to 95%. Kinetic profiles were developed for various conditions and they followed second order kinetic reactions. Adsorption equilibrium time was determined by two different approaches namely rough estimate and 2% slope criteria. The equilibrium time was found to be 5 hrs. Forward, reverse, and overall reaction rate constants were determined by approximating the kinetic data to the first order reversible kinetic model. Rate constants increased with increasing initial concentration of endosulfan. Rate limiting process was determined by using kinetics data and further confirmed by the multiple interruption test. Pore and film diffusion coefficients were determined from the half time equations. Film diffusion appeared to be the rate limiting which was further supported by the multiple interruption test.     

Sorption and photolysis studies in soil and sediment of the herbicide napropamide

Abstract

The influence of soil and sediment composition on sorption and photodegradation of the herbicide napropamide [N, N‐diethyl‐2‐(1‐naphthyloxy)propionamide] was investigated. Five soils and one sediment were selected for this study and the clay fractions were obtained by sedimentation. Sorption‐desorption was studied by batch equilibration technique and photolysis in a photoreactor emitting within 300–450 nm wavelenght with a maximum at 365 nm. Sorption increased with clay content and was not related to organic matter *content. High irreversibility of sorption was related to the greater montmorillonite content. The presence of soil or sediment reduced photolysis rate due to screen effect and this process did not depend on solid composition but on particle size distribution.