Droplet size spectra and deposits of two aerially sprayed Bacillus thuringiensis formulations on artificial samplers and live foliage

Abstract

Two commercial formulations of Bacillus thuringiensis var. kurstaki (BTK), Foray^® 48B and Thuricide^® 48LV, were applied aerially over nine spray blocks in a hardwood forest in West Virginia in 1991. Droplet spectra and spray mass deposits were determined using water‐sensitive paper strips (WSPS), glass micro‐fiber filters (GMFFs), glass plates and castor oil. Mass deposits of BTK were also assessed on natural foliage by two bioassay methods, i.e., feeding of homogenized foliage containing a starch‐sucrose solution and force‐feeding bioassay of foliar extracts containing re‐dissolved protein precipitate. Deposits on canopy foliage and ground samplers were also assessed by total protein assay and enzyme‐linked immunosorbent assay (ELISA). Droplet spectra on the WSPS were different from those on castor oil. Droplets on horizontal ground WSPS were larger than those on vertical ground WSPS. WSPS placed at canopy level collected more droplets than those at ground level. The total protein deposits (ng/cm²) were consistently higher on all blocks than the delta‐endotoxin protein deposits. Spray mass recovery on the ground samplers were low, and ranged from 2.9 to 8.0% of the applied rates.     

Assessment of aerial spray deposits in a spruce forest using in‐flight microencapsulation technique

Abstract

Spray drops were counted and sized on Kromekote® cards at ground level, and on spruce foliage at canopy level, after aerial application of a formulation containing a microencapsulation medium, over a spruce forest in Ontario. The majority of drops (70%) on foliage was 20 ‐ 75 µm range. A coarse drop size spectrum was observed on cards with a maximum diameter (Dmax) of 380 µm, and with 85% of the drops = 130 µm in diameter. Foliar drop analysis, on the other hand, indicated a finer spectrum with a Dmax of 150 µm, and with 85% of the drops = 75 µm. These results were explained on the basis of formulation ingredients, atomizer setting, weather factors, and drop retention on target surfaces. The assessment of spray deposits on glass plates at ground level indicated that about 16% of the applied spray volume reached the forest floor, a value which is comparable to those obtained in previous forestry applications using the ultra‐low‐volume (ULV) technique.     

Deposition of aerially sprayed mexacarbate on balsam fir canopy and the forest floor: Relevance to ULV applications

Abstract

Spray deposit patterns were measured on aluminum coils and live balsam fir needles at different canopy heights, following aerial application of mexacarbate (4‐dimethylamino‐3,5‐xylyl N‐methylcarbamate) over a conifer forest in New Brunswick. Droplet size spectra of the spray cloud were determined on cylindrical Kromekote® cards placed at the corresponding crown heights. Ground deposits were collected on cylindrical Kromekote cards, aluminum coils and natural balsam fir foliage placed In forest clearings and under different types of vegetation.

Canopy deposits decreased progressively from the top to the bottom level of the tree crown. This trend was observed on aluminum coils, live fir foliage, and Kromekote cards. Droplet size spectra were similar at all sampling heights of the tree crown, and were comparable to those obtained on the ground cards placed in the forest clearings. Deposits of mexacarbate obtained on ground samplers on the open forest floor were markedly lower than those found at the top canopy but were similar to those at the mid or bottom canopy level. Droplet size spectra and mexacarbate deposits obtained on samplers placed under different types of forest vegetation indicated a selective filtration of the large droplets present in the spray cloud by plant canopies.     

An improved method to study the impact of pesticide sprays on small song birds

Abstract

Four test groups of small songbirds (Zebra Finch, Poephila guttata) were sprayed in a chamber with varying concentrations of fenitrothion. Exposure levels were assessed by monitoring air concentrations, deposits of the active ingredient (AI) on glass plates and droplets/cm² on Kromekote® cards. All indices of exposure were linearly correlated and the mean AI deposit on glass plates for the four groups tested were equivalent to 38, 51, 139 and 255 g/ha or 14%, 18%, 50% and 91% of the highest permissible emitted rate for broadscale forest spraying in Canada. Significant depression in body weights and brain acetylcholinesterase levels were noted only for the highest exposure group. Fenitrothion residues in blood were detectable only at the highest exposure level, and in liver at the two higher levels. Carcass and feather residues were much higher than those in blood and liver, and were detectable at all exposure levels but the residues did not increase linearly with exposure. For one of the spray groups, we were able to compute an equivalent acute oral dose based on matching acetylcholinesterase inhibition.     

An improved method to study the impact of pesticide sprays on small song birds

Four test groups of small songbirds (Zebra Finch, Poephila guttata) were sprayed in a chamber with varying concentrations of fenitrothion. Exposure levels were assessed by monitoring air concentrations, deposits of the active ingredient (AI) on glass plates and droplets/cm2 on Kromekote cards. All indices of exposure were linearly correlated and the mean AI deposit on glass plates for the four groups tested with equivalent to 38, 51, 139 and 255 g/ha or 14%, 18%, 50% and 91% of the highest permissible emitted rate for broadscale forest spraying in Canada. Significant depression in body weights and brain acetylcholinesterase levels were noted only for the highest exposure group. Fenitrothion residues in blood were detectable only at the highest exposure level, and in liver at the two higher levels. Carcass and feather residues were much higher than those in blood and liver, and were detectable at all exposure levels but the residues did not increase linearly with exposure. For one of the spray groups, we were able to compute an equivalent acute oral dose based on matching acetylcholinesterase inhibition.     

Droplet size spectra and deposits of Bacillus thuringiensis aerial sprays,following application at two volume rates over an oak forest

Abstract

Dipel® 8AF, a commercial formulation of Bacillus thuringiensis (B.t.) was sprayed undiluted at 30 BIU in 1.8L/ha over a block B1, and sprayed after dilution with water at 30 BIU in 6.2 L/ha over another block B2 in an oak forest infested with the gypsy moth (Lymantria dispar L.) in southeastern Ontario, Canada. Spray was applied in May 1987 using a Cessna 188 Agtruck aircraft equipped with four Hicronair^® AU4000 atomizers. Droplet sizes were measured at mid‐canopy level of oak trees and at ground level using cylindrical Kromekote® cards. Deposit per unit area was assessed on aluminum oak leaves.

At the lower volume rate of 1.8 L/ha, spray droplets were smaller and droplets/cm² were lower on the cylindrical Kromekote cards in B1 than those obtained in B2 which received the higher volume rate of 6.2 L/ha. The average deposit per unit area of the aluminum oak leaves, expressed in nL of the spray volume per cm² surface area, was also correspondingly lower in B1 than in B2. This was attributed to the higher volume rate of spray application used in B2 than in B1, which resulted in larger droplets and a greater volume deposit/cm² in B2.     

Defining the spatial impacts of poultry farm ammonia emissions on species composition of adjacent woodland groundflora using Ellenberg Nitrogen Index,nitrous oxide and nitric oxide emissions and foliar nitrogen as marker variables

The marker variables, Ellenberg Nitrogen Index, nitrous oxide and nitric oxide fluxes and foliar nitrogen, were used to define the impacts of NH3 deposition from nearby livestock buildings on species composition of woodland ground flora, using a woodland site close to a major poultry complex in the UK. The study centred on 2 units in close proximity to each other, containing 350,000 birds, and estimated to emit around 140,000 kg N year(-1) as NH3. Annual mean concentrations of NH3 close to the buildings were very large (60 microg m(-3)) and declined to 3 microg m(-3) at a distance of 650 m from the buildings. Estimated total N deposition ranged from 80 kg N ha(-1) year(-1) at a distance of 30 m to 14 kg N ha(-1) year(-1) at 650 m downwind. Emissions of N2O and NO were 56 and 131 microg N m(-2) h(-1), respectively at 30 m and 13 and 80 microg N m(-2) h(-1), respectively at 250 m downwind of the livestock buildings. Species number in woodland ground flora downwind of the buildings remained fairly constant for a distance of 200 m from the units then increased considerably, doubling at a distance of 650 m. Within the first 200 m downwind, trends in plant species composition were hard to discern because of variations in tree canopy composition and cover. The mean Ellenberg N Index ranged from 6.0 immediately downwind of the livestock buildings to 4.8 at 650 m downwind. The mean abundance weighted Ellenberg N Index also declined with distance from the buildings. Tissue N concentrations in trees, herbs and mosses were all large, reflecting the substantial ammonia emissions at this site. Tissue N content of ectohydric mosses ranged from approximately 4% at 30 m downwind to 1.6% at 650 m downwind. An assessment of the relative merits of the three marker variables concludes, that while Ellenberg Index and trace gas fluxes of N2O and NO give broad indications of impacts of ammonia emissions on woodland vegetation, the application of a critical foliar N content for ectohydric mosses is the most useful method for providing spatial information which could be of value to policy developers and planners.     

Simultaneous determination of fenitrothion and aminocarb in blueberry foliage and fruits: Application to the analysis of residues in field samples

Abstract

Samples of blueberry foliage and fruits were collected from spray blocks in Ontario after aerial application of fenitrothion and aminocarb at dosage rates of 210 g active ingredient (AI)/ha and 70 g AI/ha respectively. Residues were extracted from the samples by homogenizing with ethyl acetate, cleaned up by microcolumn chromatography using alumina as adsorbent, and analyzed by GLC‐AFID with a glass column packed with 1.5% OV‐17 and 1.95% OV‐210 on 80–100 mesh Chromosorb W‐HP. Average recoveries for fenitrothion and aminocarb from foliage at three fortification levels (1.0, 0.10 and 0.01 ppm) were respectively 99 and 96%. The corresponding values for the fruits were 99 and 95%. Foliage samples collected 1 h post‐spray contained on average 1.13 ppm of fe‐nitrothion and 1.14 ppm of aminocarb. However, residue levels reached below the detection limit (<0.01 ppm) in foliage collected 15 d after treatment. In addition, the fruit samples collected after 15 d post‐spray contained extremely low levels (0.03 ppm for fenitrothion and 0.02 ppm for aminocarb) of residues, and were barely above the detection limit.     

Influence of foliar morphology and crown geometry on insecticide deposition and dissipation following an aerial spray over a mixed forest

Abstract

Deposition and dissipation of aerially sprayed phosphamidon insecticide over a mixed forest consisting of different species of coniferous and deciduous trees were studied. The data showed that the chemical deposited more and dissipated slower from deciduous foliage than from conifer needles. Differences in deposits and persistence were also found within each of the two foliar types. Leaf shape and orientation, crown geometry and foliar morphology appear to have played a role. No correlation was found between initial deposit levels and cuticular wax content of different foliar species. A controlled laboratory study showed that surface area/mass ratio played a more important role on initial deposits than pubescence/serrations present on foliar surfaces.     

Effect of sunlight radiation,rainfall and droplet spectra of sprays on persistence of bacillus thuringiensis deposits after application of dipel® 76af formulation onto conifers

Abstract

The effect of sunlight radiation, rainfall and droplet spectra of sprays on per ‐sistence of a Bacillus thuringiensis subspp. kurstaki (Btk) formulation, DiPel^® 76AF, was examined after application onto spruce [Picea glauca (Moench) Voss] foliage. The investigation consisted of three studies: (i) Study I: a laboratory microcosm study to examine the photostability of DiPel 76AF deposits on foliage after different periods of exposure to two radiation intensities, (ii) Study II: a laboratory microcosm study to examine the rainfastness of foliar deposits after exposure to different amounts of rainfall consisting of two separate droplet spectra, and (iii) Study III: a field microcosm study to investigate the influence of two different droplet spectra of DiPel 76AF sprays on foliar persistence of Btk under natural weathering conditions. In all studies, persistence of Btk was investigated both by bioassay [using spruce budworm (Choristoneura fumiferana Clemens)] and total protein assay.

The findings of Study I indicated that bioactivity of foliar deposits decreased with increasing duration of exposure to radiation, and with increasing radiation intensity. The half‐life (DT₅₀, the exposure period required for 50% of the initial bioactivity to disappear) was 5.1 d for the low intensity, and 3.9 d for the higher intensity. In contrast with the bioassay results, the total protein levels [determined by the bicinchoninic acid (BCA) method] showed no decrease with increasing duration of exposure, or with increasing radiation intensity.

The findings of Study II indicated that bioactivity of foliar deposits decreased with increasing cumulative rainfall. A new term, RF₅₀ [the amount of rain (in mm) required to washoff 50% of the initial deposit], was introduced to understand the relationship between rainfall intensity and reduction in bioactivity. When the same amount of rain was applied in different droplet sizes, the RF₅₀ value was high (5.2 mm) for the small rain droplets, and was low (2.9 mm) for the large rain droplets. Similar to the bioassay results, the total protein concentrations (determined by the BCA method) decreased with increasing amount of rain and with increasing rainfall intensity. The RF₅₀ value (obtained using ng protein /cm²) was 5.4 mm for the small rain droplets, and was 3.4 mm for the large rain droplets.

The field microcosm study indicated that when DiPel 76AF was applied in small droplets (D_v.5 of 65 μm), the persistence of bioactivity was ca 8.0 d, whereas when it was applied in large droplets (D_v.5 of 130 nm) it was ca 11 d. Bioactivity decreased with time after spray, and the DT₅₀ was 1.98 d for the spray of small droplets, and 2.87 d for that of large droplets. Similar to the bioactivity, the total protein concentrations also decreased with time after spray, and the DT₅₀ values for the small and large droplet spectra were 3.45 and 6.07 d respectively.     

Effect of additives in the Neem formulations on deposition,volatilization and persistence of Azadirachtin in spruce foliage

Abstract

Foliar deposits, volatilization and persistence of azadirachtin‐A (AZ‐A) were investigated after application of four spray mixes prepared from a wettable powder (WP) and three emulsifiable concentrate (EC) formulations of neem. They were applied at the dosage rate of 50 g AI in 4 L/ha onto potted spruce seedlings in a laboratory spray chamber. Droplet‐size spectra and deposits were assessed using Kromekote^® card/glass plate collection units. Foliar residues [dislodgeable residues (DR), penetrated residues (PR) and total residues (TR)] of AZ‐A and their volatilization were measured by HPLC at different intervals of time up to 60 h after treatment. Differences in the droplet‐size spectra and deposit levels were observed among the four spray mixes due to the influence of additives present in them. Dissipation half‐lives (DT₅₀) of the DR, PR and TR in the foliage were low (range, 19.5 to 38.9 h) and varied according to the residue type and the spray mix used. The DT₅₀ values of the DR were consistently lower (range, 19.5 to 31.9 h) than those of the PR (range, 30.5 to 38.9 h) due to preferential loss of the surface residues. The low DT₅₀ values observed for the DR and TR in the foliage sprayed with the WP spray mix were attributed to the particulate nature of the deposit. AZ‐A volatilized appreciably from the DR rather than from the PR. The variations found in the amounts of AZ‐A volatilized (42 to 58%) and unaccountable (38 to 46%) from the initial TR values in spruce foliage, after 60 h, were attributed to the physical form of the deposits on the target surface and the influences of additives present in the different spray mixes.     

California black oak response to nitrogen amendment at a high O3, nitrogen-saturated site

In a nitrogen (N) saturated forest downwind from Los Angeles, California, the cumulative response to long-term background-N and N-amendment on black oak (Quercus kelloggii) was described in a below-average and average precipitation year. Monthly measurements of leaf and branch growth, gas exchange, and canopy health attributes were conducted. The effects of both pollutant exposure and drought stress were complex due to whole tree and leaf level responses, and shade versus full sun leaf responses. N-amended trees had lower late summer carbon (C) gain and greater foliar chlorosis in the drought year. Leaf water use efficiency was lower in N-amended trees in midsummer of the average precipitation year, and there was evidence of poor stomatal control in full sun. In shade, N-amendment enhanced stomatal control. Small differences in instantaneous C uptake in full sun, lower foliar respiration, and greater C gain in low light contributed to the greater aboveground growth observed.     

Rain‐washing of mimic®, RH‐5992, from balsam fir foliage following application of two formulations

Abstract

Two formulation concentrates of the insecticide, RH‐5992 [N'‐t‐butyl‐N'‐(3,5‐dimethylbenzoyl)‐N‐(4‐ethylbenzoyI) hydrazine], an aqueous flowable (2F) and an emulsion‐suspension (ES), were diluted with water to provide spray mixes containing dosage rates ranging from 35 to 150 g of the active ingredient (AI)/ha. The mixes were sprayed in a laboratory chamber, onto balsam fir branch tips collected from field trees and greenhouse‐grown seedlings. Droplet spectra and spray mass recovery were determined on artificial samplers. Simulated rainfall of two different intensities was applied at different rain‐free periods, and rain droplet sizes were determined. Foliar washoff of RH‐5992 was assessed after application of different amounts of rain, and the increase in soil residues was evaluated.

A direct relationship was indicated between the amount of rainfall and RH‐5992 washoff. The larger the rain droplet size, the greater the amount washed off. Longer rain‐free periods made the deposits more resistant to rain. Regardless of the amount of rainfall, rain droplet size and rain‐free period, foliar deposits of the 2F formulation were washed off to a greater extent than the ES formulation. The increase in soil residues due to foliar washoff was greater for the 2F than for the ES formulation. The deposits of the emulsion‐suspension were consistently more resistant to rain‐washing than those of the aqueous flowable formulation.     

Effect of in vitro administered 2,3,7,8-tetrachlorodibenzo-p-dioxin (TCDD) on DNA-binding activities of nuclear transcription factors in NIH-3T3 mouse fibroblasts

Abstract

Most modern pesticides are expensive. Application of excessive dosage rates is likely to cause undesirable biological side‐effects and is economically wasteful. Non‐uniform distribution of the spray cloud, or application at the wrong time, may result in failure to control the pest. It is the responsibility of the field operator to acquire sufficient knowledge and skill to ensure proper use of the control agents, to increase efficiency of their usage and to reduce unwanted side‐effects. To achieve this goal, he must take into consideration the various physical factors that govern field performance of pesticides.

A simple relationship exists between the spray volume and emission rate used, and droplet size produced. The use of extremely low spray volumes (i.e., those less than 2.0 litre per ha) for forest insect control in Canada, as opposed to higher volumes used in agriculture, necessitates the release of fine droplets (ranging from 20 to 70 μm in diameter) to obtain adequate coverage of the target area. These droplets take a long time to sediment downwards, evaporate in‐flight, become smaller in size and/or form powdery residues, thus contributing to off‐target drift and impaired droplet adhesion to target surfaces. Physical factors such as rain washing, degradation by sunlight and erosion by wind also influence the longevity of pesticide deposits on foliage which is crucial during the critical period of pest control.

Factors affecting the mode of entry into insects are related to the type of ingredients used in formulation. If a pesticide acts via crawling contact, formulations which would provide surface deposits would be more beneficial than emulsions or oil‐based mixes which tend to undergo penetration into foliar cuticle. Physical factors that affect field performance of a pesticide tank mix are related to phase separation and ‘breakdown of emulsions’ in the application equipment; ‘agglomeration and caking’ of wettable powder dispersions at the bottom of the tank; impaired flow behaviour of highly viscous formulations; and coarse atomization of high‐viscosity tank mixes leading to poor target cover.     

Utilizing vortex behaviour to minimize drift

Abstract

The ULV spray emitted from a TBM flying in a cross wind was mapped by a scanning lidar system. The fate of the spray cloud for 2 min after release from the aircraft was followed as the material was transported downwind of the flight line. Vertical scans at 6 s intervals with 1 m^‐3 resolution provided detailed insight into the entrainment of the spray into the wing‐tip vortices and ultimate release to drift or deposit. Relative concentration, dosage and deposit profiles are presented for this cross‐wind case. Vortex lifetimes were found to be significantly different for the up‐wind and downwind vortices. The majority of the near field deposit was associated with the up‐wind vortex while the drift was linked to the down‐wind vortex.     

Persistence characteristics of operationally sprayed fenitrothion in nearby unsprayed areas of a conifer forest ecosystem in New Brunswick

Abstract

Persistence characteristics of operationally sprayed fenitrothion were investigated in various substrates sampled from neighbouring unsprayed areas in New Brunswick. Air, water, sediment, aquatic plants, fish, balsam fir [Abies balsamea (L.) Mill] foliage, forest soil and litter samples were collected from random sampling locations selected within 200 m from the operational spray blocks. The same substrates were resampled from the same plots and from the same locations about a year later just prior to the commencement of the operational spraying. Control samples were collected from an unsprayed site, near Sault Ste. Marie, Ontario. All samples were analysed for fenitrothion, by gas‐liquid chromatography. Except the fish samples all the substrates collected during the time of operational spraying contained low but detectable levels of fenitrothion. When collected a year later prior to the operational spray program, only balsam fir showed any detectable levels (detection limit, 0.01 ppm) of the chemical. All other samples showed no fenitrothion residues (detection limit for air, 10 ng/m³; for water, 0.01 ppb; and for other samples, 0.01 ppm). The findings confirmed that fenitrothion does not persist for an extended period of time in the aquatic substrates. The conifer foliage, however, showed persistent residues at a level of about 0.55 ppm even after the winter months, although there was no indication of accumulation of the chemical as a result of repeated exposure. The study demonstrated that the conifer needles acted as a micro sink for the chemical which showed a tendency to persist in the leaf tissues for a considerable length of time.     

Distribution and persistence of carbaryl in some terrestrial and aquatic components of a forest environment

Abstract

An oil‐based formulation of carbaryl (1‐naphthyl N‐methyl‐carbamate) (Sevin‐2‐Oil) was applied twice by a fixed‐wing aircraft at a dosage rate of 280 g of A.I./ha/application to a coniferous forest near Allardville, New Brunswick. The highest concentrations of the chemical in fir foliage, litter and forest soil 1 h after application were respectively 4.20, 1.21 and 0.59 ppm (fresh weight). The residues dissipated rapidly and the DT50 values obtained from the depletion curves were 2.3 d for foliage and 1.5 d for litter and soil samples. Very low levels (<0.1 ppm) of carbaryl persisted in foliage and litter beyond the 10 d sampling period. The maximum residue level found in stream water was 0.314 ppm and more than 50% of it had dissipated within 1 h. Low but detectable levels (0.001 ppm) of the chemical persisted in water until the end of the 10 d sampling period. Sediment samples contained a maximum level of 0.04 ppm, which dissipated below the detection limit within 5 h. Brook trout and slimy sculpins captured in the stream 1 d after the spray contained on average about 0.04 ppm of carbaryl and none of it was found in 3 d postspray samples.     

Influence of surfactants and polymeric adjuvants on physicochemical properties, droplet size spectra and deposition of fenitrothion and Bacillus thuringiensis formulations under laboratory conditions

The effect of two surfactants and two polymeric adjuvants on droplet size spectra and deposition patterns of nine spray formulations was investigated following atomization in a laboratory chamber using a spinning disc atomizer that can produce a narrow droplet size spectrum. Spray droplets were sampled using Kromekote cards and deposit recoveries were examined on glass plates. Physicochemical properties studied were: viscosity-shear rate relationship, surface tension, volatility, pH, conductance, electrophoretic mobility and zeta potential. Formulations containing low surfactant concentrations provided Newtonian liquids with low viscosities. These liquids atomized into small droplets and provided low recoveries of spray deposits on sampling units. However, formulations containing polymeric adjuvants, and a high concentration of a non-ionic surfactant provided pseudoplastic liquids with high viscosities. These formulations resulted in large droplets with high recoveries of spray deposits on sampling units. Among the physicochemical properties studied, viscosity, surface tension, volatility and electrophoretic mobility, played important roles on liquid atomization and droplet deposition.     

Influence of adjuvants on physicochemical properties, droplet size spectra and deposit patterns: relevance in pesticide applications

The influence of adjuvants on physicochemical properties, droplet size spectra and deposit patterns of five aqueous spray mixtures was studied under laboratory conditions, using two surfactants, Atlox 3409F and Triton X-114; two humectants, propylene glycol and glycerol; and one polymeric adjuvant, Agrisol FL-100F. For the sake of comparison, two fenitrothion formulations containing polymeric adjuvants, and water were also included in the study. Spray was applied at 25 degrees C and 75 +/- 5% relative humidity, in an enclosure using a twin fluid atomizer. Deposits were collected on Kromekote card/glass plate units. Physicochemical properties studied were: relative viscosity, surface tension, apparent viscosity-shear rate relationship, volatility, pH and conductance. The first four of these properties played significant roles on the droplet and deposit patterns on sampling units. However, the chemical nature of the adjuvants also played some role. Between the two surfactants tested, Triton X-114 provided a pseudoplastic medium, but both surfactant solutions provided similar droplet size spectra and deposit patterns. Between the two humectants, glycerol proved to be more advantageous than propylene glycol. The polymeric adjuvant provided droplet sizes similar to those of the two surfactants, although the recovery of the applied spray volume was higher. Among the two fenitrothion formulations, the one containing lower amounts of polymeric adjuvants showed some advantages, although deposits on the actual biological target should be examined before any definite conclusions can be drawn on the optimum adjuvant concentrations in end-use formulations.     

Influence of surfactant concentration on foliar retention of pesticides used in forestry

Abstract

Aqueous tank mixes of permethrin, fenitrothion, Bacillus thuringiensis (B.t.), diflubenzuron (DFB), and glyphosate containing different amounts of Triton® X‐114, a nonionic surfactant, were prepared. Glyphosate formed clear solutions, permethrin and fenitrothion formed emulsions, DFB and B.t provided suspensions. Emulsion stability of permethrin and fenitrothion increased with increasing surfactant level, while the emulsion drop size decreased.

Foliage of white oak, trembling aspen, white spruce and balsam fir were dipped in tank mixes of pesticides (except B.t.) labelled with ¹⁴carbon. The amount of pesticide retained on foliage was determined by liquid scintillation counting. Foliage was also dipped in non‐radioactive B.t. tank mixes, and the protein retained was determined colorimetrically. With all tank mixes, a direct relationship was observed between the mass of liquids retained on foliage and liquid viscosity. In contrast, the amount of pesticide retained was unaffected by viscosity, but was influenced by emulsion drop size. Initially, the amount of pesticide retained on foliage increased with increasing surfactant concentration. Beyond an optimum surfactant level, the emulsion drop sizes were too small and the emulsions became too stable to allow maximum retention of pesticides on foliage. With the glyphosate solutions, however, no optimum surfactant level was indicated because foliar concentrations continued to increase with increasing surfactant levels.