Hydrogen-rich fuel gas production from refuse plastic fuel pyrolysis and steam gasification

In this study, experimental conditions were optimized to maximize the production of hydrogen gas from refuse plastic fuel (RPF) by pyrolysis and steam gasification processes conducted in a laboratory-scale reactor. We carried out gasification using 10-g RPF samples at different temperatures (700°-1000°C) with and without steam. The effect of the amount of steam (0–0.25 g/min) for RPF steam gasification was also studied. The effect of K₂CO₃ as a catalyst on these processes was also investigated. Experimental results showed that the hydrogen gas yield increased with temperature; with respect to the gas composition, the hydrogen content increased mainly at the expense of other gaseous compounds, which highlights the major extension of secondary cracking reactions in the gaseous fraction at higher temperatures.     

Characterization of products obtained from pyrolysis and steam gasification of wood waste,RDF, and RPF

Pyrolysis and steam gasification of woody biomass chip (WBC) obtained from construction and demolition wastes, refuse-derived fuel (RDF), and refuse paper and plastic fuel (RPF) were performed at various temperatures using a lab-scale instrument. The gas, liquid, and solid products were examined to determine their generation amounts, properties, and the carbon balance between raw material and products.The amount of product gas and its hydrogen concentration showed a considerable difference depending on pyrolysis and steam gasification at higher temperature. The reaction of steam and solid product, char, contributed to an increase in gas amount and hydrogen concentration. The amount of liquid products generated greatly depended on temperature rather than pyrolysis or steam gasification. The compositions of liquid product varied relying on raw materials used at 500 °C but the polycyclic aromatic hydrocarbons became the major compounds at 900 °C irrespective of the raw materials used. Almost fixed carbon (FC) of raw materials remained as solid products under pyrolysis condition whereas FC started to decompose at 700 °C under steam gasification condition.For WBC, both char utilization by pyrolysis at low temperature (500 °C) and syngas recovery by steam gasification at higher temperature (900 °C) might be practical options. From the results of carbon balance of RDF and RPF, it was confirmed that the carbon conversion to liquid products conspicuously increased as the amount of plastic increased in the raw material. To recover feedstock from RPF, pyrolysis for oil recovery at low temperature (500 °C) might be one of viable options. Steam gasification at 900 °C could be an option but the method of tar reforming (e.g. catalyst utilization) should be considered.     

Gasification and reforming of biomass and waste samples by means of a novel catalyst

This study conducted gasification and catalytic reforming experiments with the expectation of obtaining new advantages on energy recovery and aimed for the development of an effective catalyst. Initially, the use of thermal gasification technology for waste treatment in line with waste-to-energy strategies was reviewed. Technological systems which have gasification were classified and their current status was discussed. Then, the results of gasification and reforming experiments showed that product gas with 50 % H₂ or more was obtained using a Ni catalyst on a mesoporous silica–based SBA-15 support (NiO/SBA-15), which we newly developed. Experiments using wood feedstock revealed that H₂ production by the catalyst was better when the NiO content was 20 % (W/W) or more than when another catalyst or the Ni catalyst with a lower Ni loading was used. Tar formation as a by-product was also well controlled by the catalyst, and use of a catalyst with 40 % NiO reduced the tar concentration to less than 0.2 g/\( {\text{m}}^{3}_{\text{N}} \). Experiments using a mixed feedstock of wood and RPF resulted in an increase in hydrocarbon concentration because of insufficient reforming. This finding suggests that future work is required to find a better solution to wood and RPF co-gasification.     

Steam gasification of epoxy circuit board in the presence of carbonates

To recover useful metals from end-of-life electronic devices and to convert plastic components from these devices into clean fuel gas, steam gasification of epoxy board samples was carried out at 600–700?°C and 0.1?MPa pressure in the presence of a ternary eutectic carbonate (lithium carbonate, sodium carbonate, and potassium carbonate). Hydrogen and carbon dioxide were the main products, and methane and carbon monoxide were detected as minor products. The gasification proceeded in two steps: an initial rapid pyrolysis followed by secondary steam gasification of char produced from the pyrolysis. The ternary eutectic carbonate accelerated not only the latter steam gasification but also the initial rapid pyrolysis. The activation energy for the steam gasification of epoxy board samples in the presence of the carbonate was 122?kJ/mol.     

Hydrogen-rich synthesis gas production from waste wood via gasification and reforming technology for fuel cell application

The purpose of this study was to establish a fuel process for an advanced power generation system in which hydrogen-rich synthesis gas, as the fuel for the molten carbonate fuel cell (MCFC), can be extracted from biomass via gasification and reforming technologies. Experiments on waste wood gasification were performed using a bench-scale gasification system. The main factors influencing hydrogen generation in the noncatalytic process and in the catalytic process were investigated, and temperature was identified as the most important factor. At 950°C, without employing a catalyst, hydrogen-rich synthesis gas containing about 54 vol% hydrogen was extracted from feedstock with appropriately designed operation parameters for the steam/carbon ratio and the equivalence ratio. However, by employing a commercial steam reforming catalyst in the reforming process, similar results were obtained at 750°C.     

Gasification of waste plastics by steam reforming in a fluidized bed

The process of producing synthetic gas from waste plastics by steam reforming was investigated. To evaluate this process, the steam reforming of the oils derived from low-density polyethylene and polystyrene were carried out using a laboratory-scale fluidized bed of Ni-Al₂O₃ catalysts. The performance of gasification in terms of carbon conversion, gas yield, and gas compositions was examined. Although oils derived from plastics contain many kinds of heavy hydrocarbons and aromatics, they were well gasified at temperatures above 1023 K with a steam/carbon ratio of 3.5 and a weight hourly space velocity of 1 h⁻¹. The hydrogen content of the product gas was very high at approximately 72 vol% for polyethylene-derived oil and 68 vol% for polystyrene-derived oil. These compositions agreed well with the values calculated from chemical equilibrium.     

Gasification applicability study of polyurethane solid refuse fuel fabricated from electric waste by measuring syngas and nitrogenous pollutant gases

To recycle polyurethane foam waste generated from electric appliance recycling centers for use as fuel in a gasification process, polyurethane solid refuse fuel fabricated as pellets was analyzed for the characteristics of elemental composition, proximate analysis, heating value, and thermo-gravimetric testing. It has a high heating value of 29.06 MJ/kg with a high content of combustibles, which could be feasibly used in any thermal process. However, the nitrogen content, of up to 7 %, was comparably higher than for other fuels such as coal, biomass, and refuse-derived fuel, and may result in the emission of nitrogenous pollutant gases of HCN and NH₃. By conducting gasification experiments on polyurethane solid refuse fuel in a fixed-bed reactor, a syngas with a heating value of 9.76 kJ/m³ and high content of both H₂ and CO were produced with good gasification efficiency; carbon conversion 54 %, and cold gas efficiency 60 %. The nitrogenous pollutant gases in syngas were measured at the concentrations of 160 ppm hydrogen cyanide and 40 ppm ammonia, which may have to be reduced using proper cleaning technologies prior to the commercialization of gasification technology for polyurethane waste.     

Coal fly ash based carbons for SO2 removal from flue gases

Two different coal fly ashes coming from the burning of two coals of different rank have been used as a precursor for the preparation of steam activated carbons. The performance of these activated carbons in the SO₂ removal was evaluated at flue gas conditions (100 °C, 1000 ppmv SO₂, 5% O₂, 6% H₂O). Different techniques were used to determine the physical and chemical characteristics of the samples in order to explain the differences found in their behaviour. A superior SO₂ removal capacity was shown by the activated carbon obtained using the fly ash coming from a subbituminous–lignite blend. Experimental results indicated that the presence of higher amount of certain metallic oxides (Ca, Fe) in the carbon-rich fraction of this fly ash probably has promoted a deeper gasification in the activation with steam. A more suitable surface chemistry and textural properties have been obtained in this case which explains the higher efficiency shown by this sample in the SO₂ removal.     

Co-gasification of wood and polyethylene with the aim of CO and H2 production

This article describes the gasification of polyethylene–wood mixtures to form syngas (H₂ and CO) with the aim of feedstock recycling via direct fermentation of syngas to ethanol. The aim was to determine the effects of four process parameters on process properties that give insight into the efficiency of gasification in general, and particularly into the optimum gasification conditions for the production of ethanol by fermentation of producer gas. Gasification experiments (fluidized bed, 800°–950°C) were done under different conditions to optimize the composition of syngas suitable for fermentation purposes. The data obtained were used for statistical analysis and modeling. In this way, the effect of each parameter on the process properties was determined and the model was used to predict the optimum gasification conditions. The parameters varied during the experiment were gasification temperature, equivalence ratio, the ratio of plastic to wood in the feed, and the amount of steam added to the process. The response models obtained proved to be statistically significant in the experimental domain. The optimum gasification conditions for maximization of carbon monoxide and hydrogen production were identified. The conditions are: temperature 900°C, equivalence ratio 0.15, amount of plastic in the feed 0.11 g/g feed, and amount of steam added 0.42 g/g feed. These optimum conditions are at the edge of the present experimental domain. The maximum combined CO and H₂ efficiency was 42%, and for the maximum yield of CO and H₂ it is necessary to minimize the polyethylene content, minimize the added steam and the equivalence ratio, and maximize temperature.     

Energy from Waste – Clean,efficient, renewable: Transitions in combustion efficiency and NOx control

Traditionally EfW (Energy from Waste) plants apply a reciprocating grate to combust waste fuel. An integrated steam generator recovers the heat of combustion and converts it to steam for use in a steam turbine/generator set. This is followed by an array of flue gas cleaning technologies to meet regulatory limitations.Modern combustion applies a two-step method using primary air to fuel the combustion process on the grate. This generates a complex mixture of pyrolysis gases, combustion gases and unused combustion air. The post-combustion step in the first pass of the boiler above the grate is intended to “clean up” this mixture by oxidizing unburned gases with secondary air.This paper describes modifications to the combustion process to minimize exhaust gas volumes and the generation of noxious gases and thus improving the overall thermal efficiency of the EfW plant. The resulting process can be coupled with an innovative SNCR (Selective Non-Catalytic Reduction) technology to form a clean and efficient solid waste combustion system.Measurements immediately above the grate show that gas compositions along the grate vary from 10% CO, 5% H₂ and 0% O₂ to essentially unused “pure” air, in good agreement with results from a mathematical model. Introducing these diverse gas compositions to the post combustion process will overwhelm its ability to process all these gas fractions in an optimal manner. Inserting an intermediate step aimed at homogenizing the mixture above the grate has shown to significantly improve the quality of combustion, allowing for optimized process parameters. These measures also resulted in reduced formation of NO_x (nitrogenous oxides) due to a lower oxygen level at which the combustion process was run (2.6 vol% O_2, wet instead of 6.0 vol% O_2, wet).This reduction establishes optimal conditions for the DyNOR? (Dynamic NO_x Reduction) NO_x reduction process. This innovative SNCR technology is adapted to situations typically encountered in solid fuel combustion. DyNOR? measures temperature in small furnace segments and delivers the reducing reagent to the exact location where it is most effective. The DyNOR? distributor reacts precisely and dynamically to rapid changes in combustion conditions, resulting in very low NO_x emissions from the stack.     

The behaviors of H2, CH4, C2H4 and C3H6 from the decomposition of polypropylene by NiO/Si–Al catalyst

The purpose of this study was to investigate the possibility of light gases produced from polypropylene, specifically hydrogen. In particular, we examined the effect of operating conditions on gaseous product and compositions in the catalytic cracking of polypropylene. We also characterized the gaseous product generated from polypropylene cracking. The feedstock (2.0 g) mixed with NiO/SiO₂–Al₂O₃ (Si–Al) was used, under non-isothermal conditions at low temperature range between 380 and 500 °C. Argon gas was used to carry the pyrolyzed gas, and the gas collected in a tedlar bag was analyzed for its behavior. We observed the behavior of major gases (H₂, CH₄, C₂H₄ and C₃H₆, etc.) according to reaction time and temperature. Finally, the effect of reaction conditions on evolved gases from catalytic cracking of polypropylene was analyzed.     

Pyrolysis of waste tyres: A review

Approximately 1.5 billion tyres are produced each year which will eventually enter the waste stream representing a major potential waste and environmental problem. However, there is growing interest in pyrolysis as a technology to treat tyres to produce valuable oil, char and gas products. The most common reactors used are fixed-bed (batch), screw kiln, rotary kiln, vacuum and fluidised-bed. The key influence on the product yield, and gas and oil composition, is the type of reactor used which in turn determines the temperature and heating rate. Tyre pyrolysis oil is chemically very complex containing aliphatic, aromatic, hetero-atom and polar fractions. The fuel characteristics of the tyre oil shows that it is similar to a gas oil or light fuel oil and has been successfully combusted in test furnaces and engines. The main gases produced from the pyrolysis of waste tyres are H₂, C₁–C₄ hydrocarbons, CO₂, CO and H₂S. Upgrading tyre pyrolysis products to high value products has concentrated on char upgrading to higher quality carbon black and to activated carbon. The use of catalysts to upgrade the oil to a aromatic-rich chemical feedstock or the production of hydrogen from waste tyres has also been reported. Examples of commercial and semi-commercial scale tyre pyrolysis systems show that small scale batch reactors and continuous rotary kiln reactors have been developed to commercial scale.     

Removal of H2S using molten carbonate at high temperature

Gasification is considered to be an effective process for energy conversion from various sources such as coal, biomass, and waste. Cleanup of the hot syngas produced by such a process may improve the thermal efficiency of the overall gasification system. Therefore, the cleanup of hot syngas from biomass gasification using molten carbonate is investigated in bench-scale tests. Molten carbonate acts as an absorbent during desulfurization and dechlorination and as a thermal catalyst for tar cracking. In this study, the performance of molten carbonate for removing H₂S was evaluated. The temperature of the molten carbonate was set within the range from 800 to 1000 °C. It is found that the removal of H₂S is significantly affected by the concentration of CO₂ in the syngas. When only a small percentage of CO₂ is present, desulfurization using molten carbonate is inadequate. However, when carbon elements, such as char and tar, are continuously supplied, H₂S removal can be maintained at a high level.To confirm the performance of the molten carbonate gas-cleaning system, purified biogas was used as a fuel in power generation tests with a molten carbonate fuel cell (MCFC). The fuel cell is a high-performance sensor for detecting gaseous impurities. When purified gas from a gas-cleaning reactor was continuously supplied to the fuel cell, the cell voltage remained stable. Thus, the molten carbonate gas-cleaning reactor was found to afford good gas-cleaning performance.     

污泥热解气化技术的研究进展

通过热解气化等热化学转化方式将污泥转变为液体或气体燃料是极具前景的污泥利用方式之一。从污泥的资源化利用方面着手,阐述了污泥热解气化技术的研究进展,分析了现有污泥热解气化工艺的优缺点和主要影响因素,并对该技术的发展趋势进行了展望。指出:高湿污泥与生物质混合进行共热解可以提高原料的转化率和整个系统的热效率;高效污泥热解气化装置的研发是目前污泥热解气化技术领域亟待解决的问题。     

Catalytic gasification of tars from a dumping site

The work deals with catalytic gasification, pyrolysis and non-catalytic gasification of tar from an industrial dumping site. All experiments were carried out in a vertical stainless steel gasification reactor at 800 °C. Crushed calcined dolomite was used as the gasification catalyst. Parameters such as addition of water and air, and the influence of the catalyst in regard to the composition of the process gas were investigated. The catalytic gasification experiment in the steady state produced process gas with the composition: 56 % of H₂, 9 % of CO, 11 % of CH₄ and 12 % of CO₂ (mol.%). Concentration of the C₂ fraction was lower than 1 mol.%. Volume flow of air was later changed from 120 to 230 ml min^?1 reducing the amount of hydrogen to 51 mol.% and that of methane to 10 mol.%. Process gas created in a non-catalytic gasification process contained 26–30 mol.% of methane, 13–15 mol.% of carbon monoxide and 15–17 mol.% of the C₂ fraction and lower amounts of hydrogen (20 mol.%) and carbon dioxide (2–3 mol.%). The highest apparent conversion of tar was reached in the catalytic gasification processes. A higher rate of catalyst deactivation can be observed when water or air is not added.     

An innovative example of herb residues recycling by gasification in a fluidized bed

A utilization way of herb residues is designed to convert herb residues to gas fuel in industrial-scale by a circulating fluidized bed gasifier in this paper. The product gas is used in the production of Chinese medicine, and the heat of the flue gas from the boiler can be used in herb residues drying to realize the energy recycling and no herb residues discharge. The gasification characteristics of herb residues in the circulating fluidized bed of 300 kg/h were investigated for about 200 h. The results indicated that the gas composition and tar yield were affected by biomass flow rate, equivalence ratio (ER), moisture content and char circulating. The lower heating value of product gas was 4–5 MJ/m³ using herb residues as feedstock. When mean biomass flow rate was at 5.5 kg m^?2 s^?1 and ER at 0.35, the product gas reached a good condition with lower heating value of 4.89 MJ/m³ and cold gas efficiency of 62.36%. When the moisture content changed from 12.5% to 18.7%, the concentrations of H₂, CO and CO₂ changed from 4.66% to 6.92%, 11.23% to 10.15%, and 16.55% to 17.82% respectively, and the tar content in gas decreased from 15.1 g/m³ to 14.4 g/m³ when the moisture content increased from 12.5% to 15.4%. There are metal oxides in the ash of herb residues, especially CaO, MgO, K₂O, Al₂O₃, and Fe₂O₃ which have obvious function on tar catalytic decomposition. The ash that attaches to the char particles can decrease the tar yield and improve the quality of gas after returning to the gasifier.     

Production of hydrogen by steam gasification of dehydrochlorinated poly(vinyl chloride) or activated carbon in the presence of various alkali compounds

Steam gasification of dehydrochlorinated poly(vinyl chloride) (PVC) or activated carbon was carried out in the presence of various alkali compounds at 3.0 MPa and 560°C–660°C in a batch reactor or in a semi-batch reactor with a flow of nitrogen and steam. Hydrogen and sodium carbonate were the main products, and methane and carbon dioxide were the minor products. Yields of hydrogen were high in the presence of sodium hydroxide and potassium hydroxide. The acceleration effect of the alkali compounds on the gasification reaction was as follows: KOH > NaOH > Ca(OH)₂ > Na₂CO₃. The rate of gasification increased with increasing partial steam pressure and NaOH/C molar ratio. However, the rate became saturated at a molar ratio of NaOH/C greater than 2.0.     

燃煤电站SCR烟气脱硝还原剂尿素热解热源的选择

介绍了燃煤电站SCR尿素热解工艺,结合当前燃料价格,通过工程案例计算,对比了各种尿素热解热源的运行费用。计算结果表明,高温蒸汽加热方案的运行费用最省,但在实际应用中受到相关条件的限制;在一定条件下,燃气加热与电加热方案是工程的优选技术方案。     

Steam gasification of tyre waste, poplar, and refuse-derived fuel: a comparative analysis

In the field of waste management, thermal disposal is a treatment option able to recover resources from "end of life" products. Pyrolysis and gasification are emerging thermal treatments that work under less drastic conditions in comparison with classic direct combustion, providing for reduced gaseous emissions of heavy metals. Moreover, they allow better recovery efficiency since the process by-products can be used as fuels (gas, oils), for both conventional (classic engines and heaters) and high efficiency apparatus (gas turbines and fuel cells), or alternatively as chemical sources or as raw materials for other processes. This paper presents a comparative study of a steam gasification process applied to three different waste types (refuse-derived fuel, poplar wood and scrap tyres), with the aim of comparing the corresponding yields and product compositions and exploring the most valuable uses of the by-products.     

Pyrolysis characteristics of the mixture of printed circuit board scraps and coal powder

Thermogravimetric (TG) analysis and infrared spectroscopy were used to analyze the pyrolysis characteristics of printed circuit board scraps (PCBs), coal powder and their mixtures under nitrogen atmosphere. The experimental results show that there is a large difference between waste PCBs and coal powder in pyrolysis processing. The pyrolysis properties of the mixing samples are the result of interaction of the PCBs and coal powder, which is influenced by the content of mixture. The degree of pyrolysis and pyrolysis properties of the mixture are much better than that of the single component. The TG and the differential thermogravimetric (DTG) curves of the PCBs mixed with coal powder move towards the high-temperature zone with increasing amount of coal powder and subsequently the DTG peak also becomes wider. The Coats–Redfern integral method was used to determine the kinetic parameters of pyrolysis reaction mechanism with the different proportion of mixture. The gas of pyrolysis mainly composes of CO₂, CO, H₂O and some hydrocarbon. The bromide characteristic absorption peak has been detected obviously in the pyrolysis gas of PCBs. On the contrary, the absorption peak of the bromide is not obvious in pyrolysis gas of the PCBs samples adding 40% coal powder.