全废砖再生轻骨料混凝土试验研究

将废粘土砖加工成粗细骨料,用于配制全废砖再生轻骨料混凝土.检测结果表明：所用废砖粗细骨料属轻骨料范畴,但其吸水率较大,且细骨料级配不良.试验表明：本试验配合比体系中,净水灰比为0.42,体积砂率为50％时最佳;以全废砖配制的再生砖轻骨料混凝土的强度发展规律与普通轻骨料混凝土类似,均有随水泥用量提高而强度提高的趋势,但随着所配制的混凝土强度等级的提高,再生轻骨料混凝土的强度提高趋势下降.以全废砖为骨料适合配制强度等级LC30及以下的再生轻骨料混凝土.     

再生混凝土骨料对钢渣骨料透水混凝土性能影响试验研究

将再生混凝土骨料以不同比例取代钢渣骨料配制透水混凝土,采用沸煮试验法考察废混凝土骨料对钢渣透水混凝土强度和体积稳定性的影响,结果表明:再生混凝土骨料可改善钢渣透水混凝土强度,减轻钢渣骨料膨胀对透水混凝土体积稳定性的影响,用再生混凝土骨料在改善钢渣骨料透水混凝土性能同时可消纳两种固体废弃物,具有环境效益和社会效益。     

双掺粉煤灰再生骨料对混凝土强度影响研究

通过试验研究再生骨料混凝土中粉煤灰和再生骨料对混凝土强度的影响。采用粉煤灰替代部分水泥、再生骨料替代部分天然粗骨料的方法,通过正交试验测定混凝土立方体抗压强度的方法,来研究粉煤灰对再生骨料混凝土强度的影响。试验得出:当再生骨料掺量为20%~30%时,粉煤灰的最佳掺量为20%左右;当再生骨料掺量高于40%、粉煤灰掺量高于20%时,其混凝土拌合物搅拌时间不小于240 s,且当粉煤灰在20%~30%时,可获得较理想的混凝土抗压强度;当粉煤灰的掺入量分布在20%~30%、再生骨料的最佳掺量为50%时,可获得较理想的混凝土抗压强度。由此得出,合理的再生骨料、粉煤灰掺量对混凝土的抗压强度影响并不明显且有提高的趋势,对降低混凝土成本,提高建筑垃圾的再生利用,有一定的经济效益和社会效益。     

Compressive strength and resistance to chloride ion penetration and carbonation of recycled aggregate concrete with varying amount of fly ash and fine recycled aggregate

Construction and demolition waste has been dramatically increased in the last decade, and social and environmental concerns on the recycling have consequently been increased. Recent technology has greatly improved the recycling process for waste concrete. This study investigates the fundamental characteristics of concrete using recycled concrete aggregate (RCA) for its application to structural concrete members. The specimens used 100% coarse RCA, various replacement levels of natural aggregate with fine RCA, and several levels of fly ash addition. Compressive strength of mortar and concrete which used RCA gradually decreased as the amount of the recycled materials increased. Regardless of curing conditions and fly ash addition, the 28 days strength of the recycled aggregate concrete was greater than the design strength, 40 MPa, with a complete replacement of coarse aggregate and a replacement level of natural fine aggregate by fine RCA up to 60%. The recycled aggregate concrete achieved sufficient resistance to the chloride ion penetration. The measured carbonation depth did not indicate a clear relationship to the fine RCA replacement ratio but the recycled aggregate concrete could also attain adequate carbonation resistance. Based on the results from the experimental investigations, it is believed that the recycled aggregate concrete can be successfully applied to structural concrete members.     

Comparative environmental assessment of natural and recycled aggregate concrete

Constant and rapid increase in construction and demolition (C&D) waste generation and consumption of natural aggregate for concrete production became one of the biggest environmental problems in the construction industry. Recycling of C&D waste represents one way to convert a waste product into a resource but the environment benefits through energy consumption, emissions and fallouts reductions are not certain. The main purpose of this study is to determine the potentials of recycled aggregate concrete (concrete made with recycled concrete aggregate) for structural applications and to compare the environmental impact of the production of two types of ready-mixed concrete: natural aggregate concrete (NAC) made entirely with river aggregate and recycled aggregate concrete (RAC) made with natural fine and recycled coarse aggregate. Based on the analysis of up-to-date experimental evidence, including own tests results, it is concluded that utilization of RAC for low-to-middle strength structural concrete and non-aggressive exposure conditions is technically feasible. The Life Cycle Assessment (LCA) is performed for raw material extraction and material production part of the concrete life cycle including transport. Assessment is based on local LCI data and on typical conditions in Serbia. Results of this specific case study show that impacts of aggregate and cement production phases are slightly larger for RAC than for NAC but the total environmental impacts depend on the natural and recycled aggregates transport distances and on transport types. Limit natural aggregate transport distances above which the environmental impacts of RAC can be equal or even lower than the impacts of NAC are calculated for the specific case study.     

Influence of aggregate pre-wetting and fly ash on mechanical properties of lightweight concrete

This study has examined the mechanical properties of lightweight aggregate concrete with a density of 1800 kg/m3. The effects of the following parameters on the concrete properties have been analyzed: the pre-wetting time of the lightweight aggregate and the percentage of pulverized fly ash used as cementitious replacement material. The strength of the lightweight aggregate was found to be the primary factor controlling the strength of high-strength lightweight concrete. An increase in the cementitious content from 420 to 450 kg/m3 does not significantly increase the strength of lightweight aggregate concrete. The relationship between the flexural and compressive strength at 28 days can be represented by the equation fr=0.69/fck. The elastic modulus was found to be much lower than that of normal weight concrete, ranging from 15.0 to 20.3 GPa. The addition of PFA increases the slump and density of lightweight aggregate concrete.     

Physical characteristics of sintered fly ash aggregate containing clay binders

A comprehensive research has been conducted to explore the influence of sintering on the properties of fly ash aggregate containing clay binders (bentonite and kaolinite). Fly ash aggregate containing clay binders, have been subjected to various sintering temperatures at different durations of 700?C1400?°C and 15?C120?min, respectively. The variation in aggregate properties, viz strength, water absorption, density and shrinkage during sintering, have been determined and discussed. In addition to these, the uniformity of sintering and rate of water absorption of sintered aggregate were also determined. No significant changes in aggregate properties were observed for aggregate sintered up to 900?°C, due to the insufficient sintering temperature range. However, the aggregate properties substantially enhanced for temperature above 1000?°C, which is attributed to the activation of liquid phase sintering. For temperatures between 1000 and 1300?°C, the aggregate with bentonite shows significant increase in shrinkage (30?%), density (density ratio 0.70), higher ten percent fines value (TPFV) (6.13?tonne), reduction in porosity (35?%), and water absorption of 4?%. However, at 1400?°C, the aggregate properties degraded due to the decomposition of mineral phases in bentonite. For aggregates with kaolinite, highest TPFV of 8.5?tonne with lowest water absorption of 2?% have been observed at 1400?°C. The presence of a higher amount of interconnected pores for aggregates sintered between 700 and 1000?°C leads to a higher rate of water absorption and then reduces to 30?% for temperatures between 1200 and 1300 and 1200 to 1400?°C for bentonite and kaolinite aggregates, respectively. This reduction is due to the reduced interconnected pores. Duration of sintering has no impact on the aggregate properties for temperatures up to 800 and 1000?°C for aggregates with bentonite and kaolinite, respectively. However, between 1000 and 1400?°C, there has been considerable improvement in the aggregate properties for increasing duration up to 60?min. In comparison, during sintering, aggregates with bentonite possessed better properties for temperature less than 1000?°C, whereas aggregates with kaolinite exhibited superior properties between 1100 and 1400?°C.     

Study of fine sediments for making lightweight aggregate.

The objective of this study was to investigate the recycling of the fine sediments of Shih-Men Reservoir to manufacture lightweight aggregate. By qualitative and quantitative analysis of the fine sediment and sintered aggregate through soil test, X-ray fluorescence, X-ray diffraction and scanning electron microscopy, a strategy of recycling fine sediment as aggregate for other similar material is proposed. The test results indicate that such fine sediment can be classified as low plastic clay, and clay of such chemical composition is located in the Riley's 'area of bloating'. The particle density of sintered lightweight aggregate decreases when the sintering temperature increases especially above 1200 degrees C due to phase transformation and formation of a vitrified layer on the surface through subsequent dehydration, bloating and collapsing stages. Our findings show that the fine sediment of Shin-Men Reservoir could be a suitable raw material for making expanded lightweight aggregate sintered at 1200 to 1300 degrees C for 10 to 12 min by a programmable furnace and a diffusion process.     

Recycling of crushed concrete and steel slag in drainage structures of geotechnical works and road pavements

Journal of Material Cycles and Waste Management - A crushed concrete aggregate, processed from construction and demolition waste and a siderurgical aggregate, processed from electric arc furnace...     

Evaluating the strength development of mortar using clinker fine aggregate with a combination of fly ash and its inhibitory effects on alkali–silica reaction and delayed ettringite formation

The aggregate composed of cement clinker, an intermediate cement product, improves strength development and mass transfer resistance of concrete. Fly ash (FA) is a supplementary cementitious material that can be substituted by cement. This study investigated the strength development of highly FA-substituted mortar mixed with cement clinker fine aggregate (CL) and tested its inhibitory effect against the alkali–silica reaction (ASR). In addition to these, this study provides the testing results of evaluating the effects of using cement clinker fine aggregate on delayed ettringite formation (DEF), which can be problematic for precast concrete products. The study results revealed that at 91 days of age, in the case of 80% replacement ratio of fly ash to cement, using CL exhibited similar strength development as mortar with limestone fine aggregate and no FA substitution. Furthermore, mortars with 70% and 80% FA substitution did not exhibit clear ASR-induced expansion even at 182 days of age. Lastly, mortar using clinker fine aggregate could suppress DEF-induced expansion at 182 days of age, which was similar to the effect obtained using FA. These results can promote the utilization of CL resources for concrete and using clinker as fine aggregate in precast concrete products.

     

Influence of transportation and pumping on the properties of concrete with large amount of copper slag fine aggregate in actual construction of port and harbor structures

Journal of Material Cycles and Waste Management - Copper slag fine aggregate (CUS) is 30% denser than normal aggregate is an effective material for port and harbor structures demanding high-density...     

Neutralization of an extremely acidic sludge and stabilization of heavy metals in flyash aggregates

An extremely acidic, heavy metal-rich sludge (pH=-1.2) was scrubbed with a Class-F fly ash in order to simultaneously neutralize the acidity and stabilize the heavy metals contained in both wastes. This paper outlines the leaching behavior of the aggregate material generated by scrubbing. For proper fly ash/sludge ratios, the fly ash acted as an outstanding neutralizer for the acidic waste. Leaching of heavy metals from the aggregate samples was below the environmental limits within a pH range between 3 and 9. Subsequent washing of the leached aggregate with acidic CALWET solutions did not result in an additional release of heavy metals. It is proposed that coordinative bonding of the metal cations onto neutral surface sites and electrostatic adsorption led to stabilization of the heavy metals within the aggregate structure below hydrolysis pHs.     

Waste tyre rubberized concrete: Properties at fresh and hardened state

The main objective of this paper is to investigate the properties of various concrete mixtures at fresh and hardened state, obtained by a partial substitution of coarse and fine aggregate with different volume percentages of waste tyres rubber particles, having the same dimensions of the replaced aggregate. Workability, unit weight, compressive and flexural strength and post-cracking behaviour were evaluated and a comparison of the results for the different rubcrete mixtures were proposed in order to define the better mix proportions in terms of mechanical properties of the rubberized concrete. Results showed in this paper were also compared to data reported in literature. Moreover, a preliminary geometrical, physical and mechanical characterization on scrap tyre rubber shreds was made.The rubberized concrete mixtures showed lower unit weight compared to plain concrete and good workability. The results of compressive and flexural tests indicated a larger reduction of mechanical properties of rubcrete when replacing coarse aggregate rather than fine aggregate. On the other hand, the post-cracking behaviour of rubberized concrete was positively affected by the substitution of coarse aggregate with rubber shreds, showing a good energy absorption and ductility indexes in the range observed for fibrous concrete, as suggested by standard (ASTM C1018-97, 1997).     

Influence of recycled aggregate quality and proportioning criteria on recycled concrete properties

This paper presents the results of experimental research using concrete produced by substituting part of the natural coarse aggregates with recycled aggregates from concrete demolition. The influence of the quality of the recycled aggregate (amount of declassified and source of aggregate), the percentage of replacement on the targeted quality of the concrete to be produced (strength and workability) has been evaluated. The granular structure of concrete and replacement criteria were analyzed in this study, factors which have not been analyzed in other studies. The following properties of recycled concretes were analyzed: density, absorption, compressive strength, elastic modulus, amount of occluded air, penetration of water under pressure and splitting tensile strength.A simplified test program was designed to control the costs of the testing while still producing sufficient data to develop reliable conclusions in order to make the number of tests viable whilst guaranteeing the reliability of the conclusions.Several factors were analyzed including the type of aggregate, the percentage of replacement, the type of sieve curve, the declassified content, the strength of concrete and workability of concrete and the replacement criteria. The type of aggregate and the percentage of replacement were the only factors that showed a clear influence on most of the properties.Compressive strength is clearly affected by the quality of recycled aggregates. If the water–cement ratio is kept constant and the loss of workability due to the effect of using recycled aggregate is compensated for with additives, the percentage of replacement of the recycled aggregate will not affect the compressive strength.The elastic modulus is affected by the percentage of replacement. If the percentage of replacement does not exceed 50%, the elastic modulus will only change slightly.     

Lightweight aggregate made from sewage sludge and incinerated ash

In this study, sewage sludge ash (SSA), with similar characteristics to expansive clay, was used as the principal material and sewage sludge (SS) as the admixture to sinter lightweight aggregate and to study the influences of raw material composition on pelletising, sintering effect and aggregate properties. Results showed that both SS and SSA could be sintered to produce synthetic aggregates individually or mixed. Increasing the amount of SS would decrease the pelletising ratio. Under the consideration of energy saving, the mixture of SSA was better for sintering normal weight aggregate. On the contrary, the mixture that added 20-30% of SS was more adequate to make lightweight aggregates. Adding SS would enhance the oxidation-reduction reaction and lower the bulk density and sintering temperature of aggregates to save energy. Sintering temperature affected the properties of sewage sludge ash lightweight aggregate (SSALA) more than retention period did. Prolonging the retention period could improve bloating effect.     

再生骨料透水砖研究现状综述

查阅了国内外众多文献,主要分析了再生骨料级配及取代率、掺合料、制备方法等因素对再生骨料透水砖的力学性能、透水性能、耐磨性与耐久性的影响,并进行了总结,为后续开展相关工作提供一定依据。     

Manufacture of artificial aggregate using MSWI bottom ash

This paper reports the results of an investigation on material recovery by stabilization/solidification of bottom ash coming from a municipal solid waste incineration plant. Stabilization/solidification was carried out to produce artificial aggregate in a rotary plate granulator by adding hydraulic binders based on cement, lime and coal fly ash. Different mixes were tested in which the bottom ash content ranged between 60% and 90%. To avoid undesirable swelling in hardened products, the ash was previously milled and then granulated at room temperature. The granules were tested to assess their suitability to be used as artificial aggregate through the measurement of the following properties: density, water absorption capacity, compressive strength and heavy metals release upon leaching. It was demonstrated that the granules can be classified as lightweight aggregate with mechanical strength strongly dependent on the type of binder. Concrete mixes were prepared with the granulated artificial aggregate and tested for in-service performance, proving to be suitable for the manufacture of standard concrete blocks in all the cases investigated.     

Investigating mechanical properties and durability of concrete containing recycled rubber ash and fibers

This article investigates the suitability of utilizing end of life rubber tyre particles in concrete as fine aggregate. Rubber ash and rubber fibers were used to develop two series of rubber ash concrete (series I) and hybrid concrete (series II) mixes. The natural fine aggregate was replaced by rubber ash (by volume of 5%, 10%, 15% and 20%) in series I; whereas in series II, the amount of rubber ash was kept constant at 10% and rubber fiber was introduced as replacement of fine aggregate (by volume of 5%, 10%, 15%, 20% and 25%). The concrete mixes were evaluated for compressive strength, flexural strength, resistance to impact loading, fatigue loading, water penetration and shrinkage strain was evaluated. It was observed that inclusion of rubber ash resulted in the improvement of impact resistance of concrete. The results also show that up to 10% rubber ash and rubber fibers can be utilized as fine aggregate to develop feasible and durable rubberized concrete pavements, crash barriers and paver blocks.

     

Recycling of PET bottles as fine aggregate in concrete

An attempt to substitute in concrete the 5% by weight of fine aggregate (natural sand) with an equal weight of PET aggregates manufactured from the waste un-washed PET bottles (WPET), is presented. The WPET particles possessed a granulometry similar to that of the substituted sand. Specimens with different cement content and water/cement ratio were manufactured. Rheological characterization on fresh concrete and mechanical tests at the ages of 28 and 365 days were performed on the WPET/concretes as well as on reference concretes containing only natural fine aggregate in order to investigate the influence of the substitution of WPET to the fine aggregate in concrete. It was found that the WPET concretes display similar workability characteristics, compressive strength and splitting tensile strength slightly lower that the reference concrete and a moderately higher ductility.     

Leaching behaviour of synthetic aggregates

In the framework of EU project "Utilising innovative kiln technology to recycle waste into synthetic aggregate" (BRST-CT98-5234), the leaching behaviour of synthetic aggregates has been studied to assess its environmental compatibility in the various stages of its use. Since the conditions are very different for the different uses, the assessment calls for a variety of different leaching conditions. The pH dependence test is used to cover important differences in pH environment to which the materials are exposed to as well as for an assessment of the buffering capacity of the material. Synthetic aggregate features a low buffer capacity, which makes it sensitive to externally imposed pH conditions. Utilisation and storage exposed to acidic conditions needs to be avoided. The results of the pH dependence test and column leaching test are mutually consistent. The CEN TC 154 method appears to provide systematically low values due to the arbitrary selection of test conditions. Synthetic aggregate studied to date will not adversely affect the concrete in its service life. The main issue for aggregate use is the recycling and the "end of life" condition, when the material becomes construction debris. Not metals, but oxyanions, such as Cr VI and Mo are most relevant under these conditions. A concise test has been applied to assess crucial aspects of leaching for different production mixes.