光催化氧化法处理染料中间体H酸水溶液

为了去除水中难氧化的有害染料中间体Ｈ酸,研究以ＴＩＯ２、ＺｎＯ、ＣｄＳ和Ｆｅ２Ｏ３为催化剂,采用低压汞灯为光源,对Ｈ酸水溶液进行光催化氧化实验．结果表明：ＴｉＯ２和ＣｄＳ的催化效果最好．采用ＴｉＯ２作催化剂,光催化氧化５ｈ后,Ｈ酸分解率可达９０％,反应速率遵从Ｌａｎｇｍｕｉｒ－Ｈｉｎｓｈｅｌｗｏｏｄ方程,Ｋ＝１２．３Ｌ／ｍｍｏｌ,ｋ＝２５．２×１０－６ｍｏｌ／ｈ．溶液中投加１０ｍｇ／Ｌ的Ｆｅ３＋或Ａｇ＋,可使反应时间缩短２—３ｈ．研究探讨了ｐＨ、ＴｉＯ２投加量和Ｈ酸浓度对催化氧化过程的影响．     

RGO/TiO2光催化降解2,4-二氯苯氧乙酸研究

通过Hummers法及紫外光/热还原工艺制得还原氧化石墨烯(RGO),采用溶胶-凝胶-煅烧法,以RGO和钛酸酊脂为前驱体制备出RGO/TiO2光催化复合材料,并利用XRD、FT-IR等对其进行了表征.对RGO/TiO2光催化降解性能的研究发现,复合光催化剂RGO/TiO2对2,4-二氯苯氧乙酸(2,4-D)的光催化降解活性显著优于纯TiO2,并且发现负载量和pH值对光催化降解性能有较大的影响:RGO/TiO2投加量为1.2g·L~(-1)、RGO负载量2%、pH为3、初始浓度为50 mg·L~(-1)反应12 h,2,4-D去除率达到98.75%;2,4-D降解率随着RGO/TiO2投加量的增大先增大后减小;RGO/TiO2对2,4-D的降解为脱氯还原和催化氧化过程,产生氯酚、苯酚等中间产物.     

不同光强下光催化降解对氯苯甲酸钠动力学

以对氯苯甲酸钠为模型污染物,研究了不同光强条件下的光催化降解动力学.结果表明对氯苯甲酸钠的光催化降解动力学可以用Langmuir-Hinshelwood模式来描述,但其中的动力学参数与光强有关.速率常数k_r随入射光强的升高而增加,而表观吸附常数K_s却随入射光强的升高而降低.k_r和K_s^-1近似与光强呈幂函数的关系.说明提高光强虽然可以增加光催化降解速率但会降低其能量利用效率,如何使用低光强照射可能是提高光催化氧化反应器能量利用效率的重要因素之一.     

CuO-TiO2/导电聚合物纤维复合材料的制备及其光催化性能

利用高压静电纺丝技术,制得含羧基的导电聚合物纤维(聚偏氟乙烯/苯乙烯-马来酸酐共聚物/纳米石墨).水热条件下在纤维表面原位合成了纳米级的TiO2,再通过水热法在TiO2表面制备了微米级的球形CuO颗粒,得到CuO-TiO2/导电聚合物纤维复合材料.运用扫描电子显微镜(SEM)、X射线衍射仪(XRD)、紫外-可见吸收光谱仪(UV-Vis)和热失重分析(TGA)对复合材料的结构与性能进行表征,并利用氙灯模拟太阳光进行光催化降解次甲基蓝实验.结果发现,CuO-TiO2/导电聚合物纤维复合材料的降解效率高于CuO-TiO2/非导电聚合物纤维、CuO-TiO2粉体和Degussa P25,光催化降解3.5h时,次甲基蓝的残留率为4.7％.     

Synthesis, crystal structure, photodegradation kinetics and photocatalytic activity of novel photocatalyst ZnBiYO4

ZnBiYO₄ was synthesized by a solid-state reaction method for the first time. The structural and photocatalytic properties of ZnBiYO₄ were characterized by X-ray diffraction, scanning electron microscopy, X-ray photoelectron spectroscopy and UV-Vis diffuse reflectance. ZnBiYO₄ crystallized with a tetragonal spinel structure with space group I41/A. The lattice parameters for ZnBiYO₄ were a = b = 11.176479 Å and c= 10.014323 Å. The band gap of ZnBiYO₄ was estimated to be 1.58 eV. The photocatalytic activity of ZnBiYO₄ was assessed by photodegradation of methyl orange under visible light irradiation. The results showed that ZnBiYO₄ had higher catalytic activity compared with N-doped TiO₂ under the same experimental conditions using visible light irradiation. The photocatalytic degradation of methyl orange with ZnBiYO₄ or N-doped TiO₂ as catalyst followed first-order reaction kinetics, and the first-order rate constant was 0.01575 and 0.00416 min^-1 for ZnBiYO₄ and N-doped TiO₂, respectively. After visible light irradiation for 220 min with ZnBiYO₄ as catalyst, complete removal and mineralization of methyl orange were observed. The reduction of total organic carbon, formation of inorganic products, SO₄^2- and NO₃^-, and evolution of CO₂ revealed the continuous mineralization of methyl orange during the photocatalytic process. The intermediate products were identified using liquid chromatography- mass spectrometry. The ZnBiYO₄/(visible light) photocatalysis system was found to be suitable for textile industry wastewater treatment and could be used to solve other environmental chemical pollution problems.     

Multi-function adsorbent-photocatalyst MXene-TiO2 composites for removal of enrofloxacin antibiotic from water

MXenes, a new family of two-dimensional transition metal carbides or nitrides, have attracted tremendous attention for various applications due to their unique properties such as good electrical conductivity, hydrophilicity, and ion intercalability. In this work, Ti₃C₂ MXene, or MX, is converted to MX-TiO₂ composites using a simple and rapid microwave hydrothermal treatment in HCl/NaCl mixture solution that induces formation of fine TiO₂ particles on the MX parent structure and imparts photocatalytic activity to the resulting MX-TiO₂ composites. The composites were used for enrofloxacin (ENR), a frequently found contaminating antibiotic, removal from water. The relative amount of the MX and TiO₂ can be controlled by controlling the hydrothermal temperature resulting in composites with tunable adsorption/photocatalytic properties. NaCl addition was found to play important role as composites synthesized without NaCl could not adsorb enrofloxacin well. Adding NaCl into the hydrothermal treatment causes sodium ions to be simultaneously intercalated into the composite structure, improving ENR adsorption greatly from 1 to 6 mg ENR/g composite. It also slows down the MX to TiO₂ conversion leading to a smaller and more uniform distribution of TiO₂ particles on the structure. MX-TiO₂/NaCl composites, which have sodium intercalated in their structures, showed both higher ENR adsorption and photocatalytic activity than composites without NaCl despite the latter having higher TiO₂ content. Adsorbed ENR on the composites can be efficiently degraded by free radicals generated from the photoexcited TiO₂ particles, leading to high photocatalytic degradation efficiency. This demonstrates the synergetic effect between adsorption and photocatalytic degradation of the synthesized compounds.     

Investigation of the effects of humic acid and H2O2 on the photocatalytic degradation of atrazine assisted by microwave

A solution of atrazine in a TiO₂ suspension, an endocrine disruptor in natural water, was tentatively treated by microwave-assisted photocatalytic technique. The effects of mannitol, oxygen, humic acid, and hydrogen dioxide on the photodegradation rate were explored. The results could be deduced as follows: the photocatalytic degradation of atrazine fits the pseudo-first-order kinetic well with k = 0.0328 s⁻¹, and ·OH was identified as the dominant reactant. Photodegradation of atrazine was hindered in the presence of humic acid, and the retardation effect increased as the concentration of humic acid increased. H₂O₂ displayed a significant negative influence on atrazine photocatalysis efficiency. Based on intermediates identified with gas chromatography-mass spectrometry (GC-MS) and Liquid chromatography-mass spectrometry (LC-MS/MS) techniques, the main degradation routes of atrazine are proposed.     

Enhanced photocatalytic activity of fish scale loaded TiO2 composites under solar light irradiation

Fish scale (FS) loaded TiO₂ composites were investigated as photocatalysts in degradation of Methyl Orange under solar light irradiation. Composites were prepared through sol-gel method by varying mass ratio of TiO₂/FS at 90:10, 70:30 and 50:50, respectively. The catalysts prepared in this study were characterized by using XRD, SEM, FT-IR and nitrogen sorption. The effects of solar irradiation, mass ratio of TiO₂/FS composites, irradiation time and catalyst loadings were studied. Synergistic effect was found in TiO₂/FS of 90:10 composite which performed higher photocatalytic degradation than synthesized TiO₂ under solar light irradiation. However, further increasing fish scale content in the composites reduced the photocatalytic activity drastically. Under solar light irradiation, all the catalysts in this study exhibited photocatalytic activity, except TiO₂/FS of 50:50 composite that only acted as a weak biosorbent without performing any photocatalytic property. Photocatalytic degradation increased with increasing catalyst loading and irradiation time but decreased with increased of initial dye concentration.     

SiO2纳米颗粒内嵌强化介孔TiO2单晶光催化降解盐酸四环素

吸附性能和光生载流子的分离效率是决定光催化降解抗生素的主要因素.为提高介孔TiO_2单晶(MSCs)的吸附性能和光生载流子的分离效率,在MSCs内部构建SiO_2纳米颗粒吸附结构.同时,利用表面光电压谱、氮气等温吸附-脱附、X射线衍射等研究其结构特性.最后,以盐酸四环素为抗生素代表,通过控制SiO_2纳米颗粒比表面积,考察SiO_2对复合材料吸附及光催化性能的影响.结果表明,SiO_2纳米颗粒与TiO_2单晶复合显著提高了材料的吸附性能,表面保护蚀刻进一步提升了材料的比表面积.实验条件下,高比表面积SiO_2-TiO_2单晶复合材料(KSiO_2@TiO_2)对盐酸四环素的平衡吸附量、降解效率、降解速率常数和矿化率分别达到了0.96 mg·g-1、90.2%、0.0079 min-1、54.4%,分别是MSCs的4.4、1.5、2.6和3.1倍.副产物分析表明,SiO_2复合介孔单晶材料更易将盐酸四环素降解为小分子物质.     

TiO2-石墨烯（Gn）复合材料光催化降解O3研究

通过改性Hummer法及溶胶凝胶法,制备出TiO2-石墨烯光催化复合材料.经吸附-光催化活性实验选出光催化活性最高的含C量为1.5%(质量分数)的TiO2-石墨烯复合材料,并在自行设计的模拟大型客机环境的气相光催化反应器中,进行O3光催化降解实验研究.结果表明,TiO2-石墨烯复合光催化材料在较短时间内对O3有较高的降解效率,且其光催化活性显著优于纯TiO2材料.初始O3浓度为(0.150～0.200)×10-6时,复合光催化剂受紫外光激发60 min的光催化降解率为66.12%,初始O3浓度为(0.950～1.000)×10-6时,其光催化降解率约为77%,较低浓度时((0.100～0.150)×10-6),O3去除率也能达到45.45%.此外,通过探讨光催化材料的重复使用性能,表明复合光催化剂重复使用4次以内,其对O3的光催化降解率保持基本稳定.     

微波改性MWNTs/TiO2复合材料对1,2,3-三氯苯的光催化降解研究

在微波辐照干化的条件下用溶胶-凝胶法制备了MWNTs/TiO2复合光催化剂.对该复合材料的表征表明：随着微波功率逐渐增大至400 W,MWNTs/TiO2复合材料管径逐渐变小,且在400 W时制备的MWNTs/TiO2复合材料分散性较好.进一步增大微波功率导致复合材料的管径增大,分散性降低.研究了不同微波辐照条件下制备的MWNTs/TiO2复合光催化剂对1,2,3-三氯苯的光催化降解效果,结果表明,该复合光催化剂对1,2,3-三氯苯的光降解遵循一级反应动力学;在微波功率为400 W、辐照时间为5 min情况下制备的复合光催化剂对1,2,3-三氯苯的降解速率最快,其反应常数为0.023 7 min^-1,该值比非微波加热干化的同样复合材料的反应速率常数值提高了52%.     

Cu改性石墨相氮化碳(g-C3N4)光催化灭活铜绿微囊藻的效能与机理研究

通过热聚合法制备不同比例Cu掺杂g-C₃N₄复合光催化材料,利用XRD、SEM/EDX、FT-IR、UV-Vis DRS、PL、XPS等技术对复合材料的形貌结构和光学性能进行表征,研究了复合材料对藻细胞的光催化灭活效果.结果表明,Cu掺杂改性可有效促进g-C₃N₄材料表面光生电子-空穴的分离,增强其对可见光的利用率,进而提升其光催化效率;随着Cu掺杂比例的增大,Cu-C₃N₄对藻细胞的灭活效果则越好.进一步研究发现,H₂O₂和·O₂^-是Cu-C₃N₄光催化灭藻过程中起主要作用的活性物质,会损伤藻细胞的形态结构、抗氧化酶系统和光合系统,导致藻细胞大量死亡.     

连续流光催化消毒器灭活E.coli及病毒的性能

紫外消毒是污水处理常用技术.紫外线仅能破坏微生物的遗传物质,阻断其繁殖,并不能彻底杀死微生物,一旦停止紫外光照射,微生物可在修复酶的作用下恢复活性.光催化过程能产生强氧化性·OH,破坏细胞壁和细胞膜,彻底杀死微生物.为考察光催化技术消毒效率、抑制复活性能及应用潜力,在市售紫外消毒器中安装了光催化组件,搭建了连续流动式光催化消毒器.以大肠杆菌(E.coli)和噬菌体为目标物评价其消毒能力.紫外剂量50 m J·cm-2条件下,初始浓度3.40×106CFU·m L-1的E.coli原水流经紫外消毒器后被去除4.12 log10的E.coli,而流经光催化消毒器后去除4.79 log10.同时光催化处理后E.coli的光复活率仅为紫外消毒后的17%.连续运行40 h的灭菌能力稳定.光催化设备对噬菌体F2和噬菌体MS2的去除率分别为6.37 log10和6.00 log10,表明该设备也具有病毒去除能力.     

玻璃载体TiO2薄层光催化降解久效磷农药

研究了利用TiO₂薄层光催化降解久效磷农药的可行性。结果表明,0.65×10-4mol/L的久效磷经375W中压汞灯照射60min,被完全光催化降解至PO₄3-;加入微量的Fe3++或H2O2可提高久效磷农药的光解率;另外还研究了TiO₂薄层的附着量、反应液初始pH值、空气流量等因素对光催化降解的影响。光照80 h,TiO₂的光催化活性没有减弱,可连续使用。      

Photocatalytic degradation of 4-tert-octylphenol in a spiral photoreactor system

A spiral photoreactor system (SPS) was developed for the degradation of 4-tert-octylphenol (4-t-OP) in aqueous phase. 4-t-OP was previously considered as a endocrine disrupting compound frequently present in water. The direct photodegradation reaction caused by the SPS was found to accord with the characteristic of apparent first-order reaction with reaction rate constantk= 4.8 × 10^-2 min^-1. However, the direct photodegradation reaction could not make the 4-t-OP mineralized. The photodegradation efficiency increased from 88% to 91.2% in 45 min irradiation period after the internal surface of SPS was sintered with TiO₂ thin film as catalyst. Catalyst concentration, number of catalyst coating layers and initial concentration of 4-t-OP were proven to be the factors affecting the photocatalytic degradation performance of the SPS on aqueous 4-t-OP. The degradation mechanism was investigated and the byproducts were analyzed using total organic carbon analyzer (TOC) and LC-MS. The possible chemical structures of the products were suggested. SPS with single layer of TiO₂ prepared by sintering 13.6% of TiO₂ precursor was proven to be more efficient than most of previous systems for removal of 4-t-OP from aqueous phase. 28.3% of the 4-t-OP was mineralized in 45 min according to the decreased amount of TOC value.     

Synergistic photocatalytic degradation of pyridine using precious metal supported TiO2 with KBrO3

A series of precious metals catalysts （M/TiO/, M = Ru, Rh, Pd, Ag, Ir, Pt or Au） were prepared by a light deposition method and the synergistic photocatalytic degradations of pyridine （20 mg/L） under UV irradiation （365 nm） using M/TiO2 with electron capture agent KBrO3 have been investigated. The results show that KBrO3 has a greatly synergistic role on M/TiO2 and the photocatalytic activity of M/TiO2 is closely related to its work function. Ag could greatly enhance the activity of TiO2 due to the binding characteristics of pyridine on Ag. Under the conditions of 0.5 wt.% Ag loading, Ag/TiO2 concentration of 0.1 g/L, KlrO3 concentration of 10 mmol/L and reaction liquid pH value at 9, the pyridine can be degraded by 64% within 3 hr, doubled than TiO2 photocatalytic system. The degradation kinetics of pyridine follows first-order kinetics and k = 5.53 × 10-3 min^-1.     

BiOCl/TiO2的氯化改性及其新式光生自由基催化反应

采用溶胶凝胶法制备了BiOCl/TiO₂复合催化剂,透射电镜（TEM）照片显示,两种半导体分布均匀、相互连接,形成的异质结可以为电子传导提供有效通道.经过氯化处理的复合材料具备更强的光催化能力,在紫外光条件下对苯的降解率达到90%,是原BiOCl/TiO₂的2倍、纯TiO₂的10倍.本文利用X射线光电子能谱、红外光谱和电子顺磁共振,对表面氯化的机理进行研究.结果表明,氯元素以Ti—Cl的方式吸附在催化剂表面,在光照条件下光生空穴夺取一个电子,使其生成氯自由基,进而配合超氧、羟基,构成一种新型的三自由基光催化体系,使催化降解能力大幅提升.最后,利用实验方法得到了光生氯自由基的直接证据,并构建了该体系的光催化反应机理.     

Investigation of UV-TiO2 photocatalysis and its mechanism in Bacillus subtilis spore inactivation

The inactivation levels of Bacillus subtilis spores for various disinfection processes （ultraviolet （UV）, TiO2 and UV-TiO2） were compared. The results showed that the inactivation effect of B. subtilis spores by UV treatment alone was far below that for bacteria without endospores. TiO2 alone in the dark, as a control experiment, exhibited almost no inactivation effect. Compared with UV treatment alone, the inactivation effect increased significantly with the addition of TiO2. Increases of the UV irradiance and Ti02 concentration both contributed to the increase of the inactivation effect. Lipid peroxidation was found to be the underlying mechanism of inactivation. Malondialdehyde （MDA）, the degradation product of lipid peroxidation, was used as an index to determine the extent of the reaction. The MDA concentration surged surprisingly to 3.24 nmol/mg dry cell with the combination disinfection for 600 see （0.10 mW/cm2 irradiance and 10 mg/L TiO2）. In contrast, for UV alone or TiO2 in the dark, the MDA concentration was 0.38 and 0.25 nmol/mg dry cell, respectively, under the same conditions. This indicated that both UV and TiO2 were essential for lipid peroxidation. Changes in cell ultrastructure were observed by transmission electron microscopy. The cell membrane was heavily damaged and cellular contents were completely lysed with the UV-TiO2 process, suggesting that lipid peroxidation was the root of the enhancement in inactivation efficiency.     

Photocatalytic degradation of dichlorvos using TiO2 supported on hollow glass microbeads

In this paper, a method for TiO₂ supported on hollow glass microbeads was described and the feasibility of photocatalytic degradation of dichlorvos using supported TiO₂(TiO₂/beads) was studied. The results showed that 1.0×10^-4 mol.dm^-3 of dichlovos could be completely photocatalytically degraded into PO₄^3- after 120 min illumination with a 375 W medium pressure mercury lamp. The effects of the amount of TiO₂/beads and concentration of Cu²⁺ on the photocatalytic degradation were also investigated. Some intemediate products of photocatalytic degradation of dichlorvos were detected.     

TiO2光催化氧化苯酚动力学研究

以中压汞灯为光源,研究了苯酚在ＴｉＯ２水悬浮液中降解动力学,考察了苯酚在起始浓度,气相氧浓度,催化剂投加量（ＴｉＯ２）光强度以及催化剂煅烧温度对苯酚光解速率的影响,揭示了苯酚多相光催化氧化反应的特点,反应过程符合表现一级动力学规律,气相氧的影响为一级,苯酚初始浓度的影响为负一级,在一定光强度下,催化剂的投加量存在一最值值,说明有效光强度,气相氧以及催化剂投加量是光催化氧化反应的关键因素,适当地热处