Japan’s waste management policies for dioxins and polychlorinated biphenyls

We summarize the measures taken by the Japanese government to prevent the emission of dioxins and polychlorinated biphenyls (PCBs) into the environment. Because incineration is the main method of waste management in Japan, reducing the amount of dioxins emitted from waste incinerators is an essential aspect of proper waste treatment. Intensive measures to prevent the formation of dioxins at the source have been implemented, with a focus on waste treatment methods and improving comprehensive management. The efforts have been very successful, with a 95% reduction in the amount of dioxins emitted between 1997 and 2003. The toxicity of PCBs has been monitored with keen interest since the Yusho incident. Unfortunately, treatment facilities for PCB wastes were not built until long after PCBs had been removed from use, and PCB wastes remained in storage in an untreated state. The Japanese government has promoted the construction of facilities for treating PCB wastes, and five such facilities have commenced operations. To more completely eradicate dioxins, a future challenge will be to reduce the amount of PCB-derived dioxins, which are persistent in the environment and have a long exposure pathway from the environment media to the organism and the human body.     

炉排炉焚烧垃圾过程中主要污染物的控制

概述了二恶英、重金属、酸性气体、灰渣等垃圾焚烧的主要污染物,以二段式（往复）焚烧炉为例,介绍了炉排炉焚烧处理工艺和污染控制设备。提出通过控制垃圾焚烧条件、尾气处理以及吸附等方法,可以有效控制二恶英类污染物的排放;重金属的控制可以用除尘器或使用相应的吸附剂处理;采用较为成熟的烟气处理技术,可以控制处理酸性气体;灰渣可采用固化稳定化或酸提取法处置。     

Environmental impact assessment of the incineration of municipal solid waste with auxiliary coal in China

The environmental impacts of waste incineration with auxiliary coal were investigated using the life-cycle-based software, EASEWASTE, based on the municipal solid waste (MSW) management system in Shuozhou City. In the current system, MSW is collected, transported, and incinerated with 250kg of coal per ton of waste. Based on observed environmental impacts of incineration, fossil CO(2) and heavy metals were primary contributors to global warming and ecotoxicity in soil, respectively. Compared with incinerators using excess coal, incineration with adequate coal presents significant benefits in mitigating global warming, whereas incineration with a mass of coal can avoid more impacts to acidification, photochemical ozone and nutrient enrichment because of increased electricity substitution and reduced emission from coal power plants. The "Emission standard of air pollutants for thermal power plants (GB13223-2011)" implemented in 2012 introduced stricter policies on controlling SO(2) and NO(x) emissions from coal power plants. Thus, increased use of auxiliary coal during incineration yields fewer avoided impacts on acidification and nutrient enrichment. When two-thirds of ash is source-separated and landfilled, the incineration of rest-waste presents better results on global warming, acidification, nutrient enrichment, and even ecotoxicity in soil. This process is considered a promising solution for MSW management in Shuozhou City. Weighted normalized environmental impacts were assessed based on Chinese political reduction targets. Results indicate that heavy metal and acidic gas emissions should be given more attention in waste incineration. This study provides scientific support for the management of MSW systems dominated by incineration with auxiliary coal in China.     

CO₂ emission factors for waste incineration: Influence from source separation of recyclable materials

CO₂-loads from combustible waste are important inputs for national CO₂ inventories and life-cycle assessments (LCA). CO₂ emissions from waste incinerators are often expressed by emission factors in kg fossil CO₂ emitted per GJ energy content of the waste. Various studies have shown considerable variations between emission factors for different incinerators, but the background for these variations has not been thoroughly examined. One important reason may be variations in collection of recyclable materials as source separation alters the composition of the residual waste incinerated. The objective of this study was to quantify the importance of source separation for determination of emission factors for incineration of residual household waste. This was done by mimicking various source separation scenarios and based on waste composition data calculating resulting emission factors for residual waste routed to incineration. Emission factors ranged from 27 to 40 kg CO₂/GJ. The results appeared most sensitive towards variations in waste composition and water content. Recycling rates and lower heating values could not be used as simple indicators of the resulting emission factors for residual household waste; however the fossil carbon ratio of the waste after source separation was found to be appropriately correlated with the emission factor. Based on the results, it is recommended to carefully evaluate the source separation and collection systems behind reported literature values when comparing different studies and when using the values for environmental assessment purposes.     

Laboratory study on the behaviour of spent AA household alkaline batteries in incineration

The quantitative evaluation of emissions from incineration is essential when Life Cycle Assessment (LCA) studies consider this process as an end-of-life solution for some wastes. Thus, the objective of this work is to quantify the main gaseous emissions produced when spent AA alkaline batteries are incinerated. With this aim, batteries were kept for 1h at 1273K in a refractory steel tube hold in a horizontal electric furnace with temperature control. At one end of the refractory steel tube, a constant air flow input assures the presence of oxygen in the atmosphere and guides the gaseous emissions to a filter system followed by a set of two bubbler flasks having an aqueous solution of 10% (v/v) nitric acid. After each set of experiments, sulphur, chlorides and metals (As, Cd, Co, Cr, Cu, Fe, Hg, Mn, Ni, Pb, Sb, Tl and Zn) were analyzed in both the solutions obtained from the steel tube washing and from the bubblers. Sulphur, chlorides and metals were quantified, respectively, using barium sulfate gravimetry, the Volhard method and atomic absorption spectrometry (AAS). The emissions of zinc, the most emitted metal, represent about 6.5% of the zinc content in the batteries. Emissions of manganese (whose oxide is the main component of the cathode) and iron (from the cathode collector) are negligible when compared with their amount in AA alkaline batteries. Mercury is the metal with higher volatility in the composition of the batteries and was collected even in the second bubbler flask. The amount of chlorides collected corresponds to about 36% of the chlorine in the battery sleeve that is made from PVC. A considerable part of the HCl formed in PVC plastic sleeve incineration is neutralized with KOH, zinc and manganese oxides and, thus, it is not totally released in the gas. Some of the emissions are predictable through a thermodynamic data analysis at temperatures in the range of 1200-1300K taking into account the composition of the batteries. This analysis was done for most of potential reactions between components in the batteries as well as between them and the surrounding atmosphere and it reasonably agrees the experimental results. The results obtained show the role of alkaline batteries at the acid gases cleaning process, through the neutralization reactions of some of their components. Therefore, LCA of spent AA alkaline batteries at the municipal solid waste (MSW) incineration process must consider this contribution.     

Atmospheric Budget of Non-Seasalt Chlorine in the Kanto District,Japan

To evaluate the influence of anthropogenic emission of HCl on the air quality in the Kanto district of Japan, the atmospheric budgetof non-seasalt Cl (nssCl) was analyzed. The Kanto district, which consists of the Tokyo metropolis and the six surrounding prefectures, is the most densely populated region in Japan. The emission intensity of HCl is extremely high compared with those in other regions and most western countries. In this study, the annual wet and dry depositions of nssClwere estimated on a 0.25 × 0.25° grid over the Kanto district based on the concentration monitoring resultsand meteorological data. The budget analysis was conducted by comparing the estimated deposition with the emission of HCl. As a result, the annual total (wet + dry) deposition of nssCl was estimated to be 32 kt yr^-1, which closely agreed with HCl emission (36 kt yr^-1) from waste incineration in this area. The result suggested that the anthropogenic emission of HCl had a significant influence on the air quality and the deposition of acidity in this area.     

The estimation of N2O emissions from municipal solid waste incineration facilities: The Korea case

The greenhouse gases (GHGs) generated in municipal solid waste (MSW) incineration are carbon dioxide (CO₂), methane (CH₄), and nitrous oxide (N₂O). In South Korea case, the total of GHGs from the waste incineration facilities has been increasing at an annual rate 10%. In these view, waste incineration facilities should consider to reduce GHG emissions.This study is designed to estimate the N₂O emission factors from MSW incineration plants, and calculate the N₂O emissions based on these factors. The three MSW incinerators examined in this study were either stoker or both stoker and rotary kiln facilities. The N₂O concentrations from the MSW incinerators were measured using gas chromatography-electron capture detection (GC-ECD) equipment.The average of the N₂O emission factors for the M01 plant, M02 plant, and M03 plant are 71, 75, and 153 g-N₂O/ton-waste, respectively. These results showed a significant difference from the default values of the intergovernmental panel on climate change (IPCC), while approaching those values derived in Japan and Germany. Furthermore, comparing the results of this study to the Korea Energy Economics Institute (KEEI) (2007) data on waste incineration, N₂O emissions from MSW incineration comprised 19% of the total N₂O emissions.     

Substance flow analysis of coplanar PCBs released from waste incineration processes

Previous reports have focused on the emission of coplanar polychlorinated biphenyls (Co-PCBs) which have a toxic mechanism similar to that of polychlorinated dibenzo-p-dioxins and polychlorinated dibenzofurans (PCDDs/DFs) released from municipal solid waste (MSW) incineration. Such emissions accounted for a small percentage of all the dioxins (PCDDs/DFs and Co-PCBs) recorded at the toxicity equivalent (TEQ) level. There is, however, very little information about Co-PCBs, such as the quantities being released and their effect on overall environmental pollution. The aim of this research has been to clarify the substance flow of Co-PCBs from MSW incineration processes. The results reveal that whereas the input of Co-PCBs into the MSW incineration facilities in Kyoto City was 0.13–0.29 μg-TEQ per ton waste, the total output of Co-PCBs (the sum of Co-PCBs released from emission gas, fly ash, and bottom ash) was 4.9 μg-TEQ per ton waste. The total output was therefore found to be higher than the total input. Over 90% of the total PCBs were decomposed in the incineration process. In comparing the profiles of congeners and homologues, those in the MSW were found to be similar to those detected in the atmosphere and products containing PCBs, but different from those in the MSW incineration gas. Received: August 26, 1998 / Accepted: March 2, 1999     

Mitigation of global greenhouse gas emissions from waste: conclusions and strategies from the Intergovernmental Panel on Climate Change (IPCC) Fourth Assessment Report. Working Group III (Mitigation).

Greenhouse gas (GHG) emissions from post-consumer waste and wastewater are a small contributor (about 3%) to total global anthropogenic GHG emissions. Emissions for 2004-2005 totalled 1.4 Gt CO2-eq year(-1) relative to total emissions from all sectors of 49 Gt CO2-eq year(-1) [including carbon dioxide (CO2), methane (CH4), nitrous oxide (N2O), and F-gases normalized according to their 100-year global warming potentials (GWP)]. The CH4 from landfills and wastewater collectively accounted for about 90% of waste sector emissions, or about 18% of global anthropogenic methane emissions (which were about 14% of the global total in 2004). Wastewater N2O and CO2 from the incineration of waste containing fossil carbon (plastics; synthetic textiles) are minor sources. Due to the wide range of mature technologies that can mitigate GHG emissions from waste and provide public health, environmental protection, and sustainable development co-benefits, existing waste management practices can provide effective mitigation of GHG emissions from this sector. Current mitigation technologies include landfill gas recovery, improved landfill practices, and engineered wastewater management. In addition, significant GHG generation is avoided through controlled composting, state-of-the-art incineration, and expanded sanitation coverage. Reduced waste generation and the exploitation of energy from waste (landfill gas, incineration, anaerobic digester biogas) produce an indirect reduction of GHG emissions through the conservation of raw materials, improved energy and resource efficiency, and fossil fuel avoidance. Flexible strategies and financial incentives can expand waste management options to achieve GHG mitigation goals; local technology decisions are influenced by a variety of factors such as waste quantity and characteristics, cost and financing issues, infrastructure requirements including available land area, collection and transport considerations, and regulatory constraints. Existing studies on mitigation potentials and costs for the waste sector tend to focus on landfill CH4 as the baseline. The commercial recovery of landfill CH4 as a source of renewable energy has been practised at full scale since 1975 and currently exceeds 105 Mt CO2-eq year(-1). Although landfill CH4 emissions from developed countries have been largely stabilized, emissions from developing countries are increasing as more controlled (anaerobic) landfilling practices are implemented; these emissions could be reduced by accelerating the introduction of engineered gas recovery, increasing rates of waste minimization and recycling, and implementing alternative waste management strategies provided they are affordable, effective, and sustainable. Aided by Kyoto mechanisms such as the Clean Development Mechanism (CDM) and Joint Implementation (JI), the total global economic mitigation potential for reducing waste sector emissions in 2030 is estimated to be > 1000 Mt CO2-eq (or 70% of estimated emissions) at costs below 100 US$ t(-1) CO2-eq year(-1). An estimated 20-30% of projected emissions for 2030 can be reduced at negative cost and 30-50% at costs < 20 US$ t(-) CO2-eq year(-1). As landfills produce CH4 for several decades, incineration and composting are complementary mitigation measures to landfill gas recovery in the short- to medium-term--at the present time, there are > 130 Mt waste year(-1) incinerated at more than 600 plants. Current uncertainties with respect to emissions and mitigation potentials could be reduced by more consistent national definitions, coordinated international data collection, standardized data analysis, field validation of models, and consistent application of life-cycle assessment tools inclusive of fossil fuel offsets.     

Waste incineration,PVC, and dioxins

Waste incineration is becoming increasingly necessary to tackle the rapidly rising amounts of municipal solid waste (MSW); in China many large cities are already surrounded by a girdle of landfills. Still, the not-in-my-backyard (nimby) syndrome holds strong. This attitude stems from fear of dioxins. These have been associated with incineration (‘dioxin factories’) and at times also with polyvinylchloride. In this paper this issue is analysed. China should build additional trust in MSW incineration, following promulgation of stricter emission standards, enforced by stringent controls.     

The benefits of flue gas recirculation in waste incineration

Flue gas recirculation in the incinerator combustion chamber is an operative technique that offers substantial benefits in managing waste incineration. The advantages that can be obtained are both economic and environmental and are determined by the low flow rate of fumes actually emitted if compared to the flue gas released when recirculation is not conducted. Simulations of two incineration processes, with and without flue gas recirculation, have been carried out by using a commercial flowsheeting simulator. The results of the simulations demonstrate that, from an economic point of view, the proposed technique permits a greater level of energy recovery (up to +3%) and, at the same time, lower investment costs as far as the equipment and machinery constituting the air pollution control section of the plant are concerned. At equal treatment system efficiencies, the environmental benefits stem from the decrease in the emission of atmospheric pollutants. Throughout the paper reference is made to the EC legislation in the field of environmental protection, thus ensuring the general validity in the EU of the foundations laid and conclusions drawn henceforth. A numerical example concerning mercury emission quantifies the reported considerations and illustrates that flue gas recirculation reduces emission of this pollutant by 50%.     

Enrichment of elements in industrial waste incineration bottom ashes obtained from three different types of incinerators,as studied by ICP-AES and ICP-MS

The elemental composition of the industrial waste incineration bottom ash (IWIBA) samples collected from three different types of incinerator with different kinds of wastes were compared. The major-to-ultratrace elements in the IWIBA samples were determined by inductively coupled plasma atomic emission spectrometry (ICP-AES) and inductively coupled plasma mass spectrometry (ICP-MS). As a result, ca. 40 elements in the concentration range from milligrams per gram to submicrograms per gram could be determined with relative standard deviations of less than 5%. The IWIBA sample from petrochemical wastes contained lower concentrations of the elements, because fewer mineral constituents were contained in the input waste materials. On the contrary, the elemental concentrations in the IWIBA sample from industrial solid wastes provided the highest values for most elements, while the elemental compositions of the IWIBA sample from food wastes were similar to those of municipal solid waste incineration bottom ash. In addition, it was found from the analytical results that the levels of various heavy metals such as Cr, Mn, Fe, Ni, Cu, As, Zr, Mo, Sb, Ba, and Pb were higher in the IWIBA samples than in municipal solid waste incineration bottom ash. The enrichment factors of the elements in the IWIBA samples were estimated from the analytical results to compare the elemental distributions in incineration bottom ashes in relation to their mining influence factors, which are the indices for human use of the elements.     

Optimization of the food waste water incineration with respect to CO and NO<Subscript>x</Subscript> emission characteristics

The incineration of food waste water in conjunction with the domestic waste is getting attention as a food waste water treatment method, due to its low treatment cost and high efficiency. Many studies verified that the ammonia in the food waste water served as a reducing agent to suppress the generation of NO_x when the food waste water was injected and incinerated. However, they have not revealed the correlation between the change in the concentration of the CO and NO_x by the influence of the solid matters contained in the food waste water on the incineration of the wastes. The purpose of this study is to determine the optimum amount of the food waste water injected through four nozzles in the primary and secondary incineration chambers and to assess the correlation between the concentration of CO and NO_x in accordance with the food waste water injection in each chamber of the incinerator. For the study, four food waste water injection nozzles were installed; two (A and B) at the top of the primary incineration chamber and the other two (C and D) in the secondary incineration chamber. The correlation between the change in the concentration of CO and NO_x was studied adjusting the amount of the food waste water injected through the nozzles. From the result, Case II showed the concentration of CO and NO_x as 1.8–10 and 14–26 ppm, respectively, while Case I showed that of CO and NO_x as 15–30 and 9–18 ppm, respectively. Those levels are well below the Korean emission criteria, 50 ppm for CO and 80 ppm for NO_x. Based on the results, it is evident there is a certain trade-off between emission of CO and NO_x, and Case II which has relatively low concentration of CO is easier and cheaper to control.     

Tools for evaluation of impact associated with MSW incineration: LCA and integrated environmental monitoring system

The identification of significant pollutants emitted from the contamination source is the first step in evaluating the impact associated with anthropic activity. Municipal solid waste (MSW) incinerators are still generally perceived as great pollutant sources, in particular due to their gaseous emissions from the stack, which constitute the major effluent from the plant. In this work a life cycle assessment and an integrated environmental monitoring system were applied together, in order to obtain complete information about the incineration process and its environmental impact. The former is a proven methodology, but its application to waste management systems constitutes a relatively new field of application with a great developmental potential. The contribution of the incineration process to the different environmental impact categories was investigated, finding many avoided impacts due to energy recovery. The latter is an innovative approach that allows a remarkable understanding of impact due to a contamination source; interesting correlations were found between heavy metals both in gas emissions and in natural matrices in the surroundings.     

Emission of dioxins/furans and other U-POPs from test burns of non-POP pesticides in a hazardous waste incinerator

This paper presents the results of test burns for obsolete pesticides (OPs) of the permethrin group in a high temperature incinerator (HTI) in Southeast Asia. Three test burn runs were conducted, a baseline run when no OP was fed to the incinerator, and two test runs with different mixtures of OP compounds (formula 1 and 2, refer to Table 1 for detail) containing chlorine in the feeding wastes. The unintentional formed persistent organic pollutants (U-POPs) including 17 dioxins/furans, 12 dioxin-like PCBs and 12 chlorobenzenes (CBs) were monitored in all input materials and all discharges (flue gas, scrubbing liquid and solid residues). The results show relatively high levels of the U-POPs in the flue gas emission with total dioxins/furans of 4.4, 3.4, and 8.4 ng I-TEQ/m³ in the baseline, test run 1 and test run 2, respectively, which are above international acceptable emission levels. The PCB levels in flue gas were, respectively, 0.01, 0.3 and 0.4 ng I-TEQ/m³. The baseline thus had similar U-POPs levels with the OP test runs.In stack emission, approximately 90% of the U-POPs and 100% of CBs were present in gas phase. The emission factors, mass of pollutants per metric ton (tonne) of input waste, of U-POPs associated with fly ash (from bag house) were the highest, followed by flue gas and bottom ash while those associated with scrubbing liquid were relatively low. Among the waste input material only the black toner power contained U-POPs, but at low levels. The profiles of the dioxins/furans and PCBs in the toner waste were significantly different from that in the discharges. Despite the overall good destruction and removal efficiency of permethrin (better than 90%) the high emission of U-POPs and CBs from the test burn is of another more serious concern. To our best knowledge the findings of this study are the first of this kind for the Southeast Asia. The findings emphasize that if not properly conducted a standard destruction technology of a non-POP chemical can lead to a release of a range of more dangerous U-POPs into the environment.     

Environmental and economic life cycle assessment for sewage sludge treatment processes in Japan

Life cycle assessment for sewage sludge treatment was carried out by estimating the environmental and economic impacts of the six alternative scenarios most often used in Japan: dewatering, composting, drying, incineration, incinerated ash melting and dewatered sludge melting, each with or without digestion. Three end-of-life treatments were also studied: landfilling, agricultural application and building material application. The results demonstrate that sewage sludge digestion can reduce the environmental load and cost through reduced dry matter volume. The global warming potential (GWP) generated from incineration and melting processes can be significantly reduced through the reuse of waste heat for electricity and/or heat generation. Equipment production in scenarios except dewatering has an important effect on GWP, whereas the contribution of construction is negligible. In addition, the results show that the dewatering scenario has the highest impact on land use and cost, the drying scenario has the highest impact on GWP and acidification, and the incinerated ash melting scenario has the highest impact on human toxicity due to re-emissions of heavy metals from incinerated ash in the melting unit process. On the contrary, the dewatering, composting and incineration scenarios generate the lowest impact on human toxicity, land use and acidification, respectively, and the incinerated ash melting scenario has the lowest impact on GWP and cost. Heavy metals released from atmospheric effluents generated the highest human toxicity impact, with the effect of dioxin emissions being significantly lower. This study proved that the dewatered sludge melting scenario is an environmentally optimal and economically affordable method.     

Quantification of landfill emissions to air: a case study of the Ano Liosia landfill site in the greater Athens area.

Fugitive pollutant emissions from municipal solid waste landfills have the potential to cause annoyance and health impacts in the surrounding residential areas. The overall objective of this research was to perform an assessment of fugitive pollutant emissions and a dispersion analysis downwind of a specific landfill site. The study was performed at the closed Ano Liosia landfill site which is located in the greater Athens area. The human exposure from priority to health-risk pollutants emitted from landfill, such as vinyl chloride and benzene, was estimated by the landfill gas emission LandGEM 2.01 software combined with the atmospheric long-term dispersion model ISC3-LT. The emission and meteorological conditions under which the models were applied referred to the worst-case scenario. This scenario was used for the evaluation of the maximum human exposure assessed beyond the Ano Liosia landfill towards the residential areas. The above scenario provides the minimum downwind distance of the health-risk zone which is calculated to be equal to 1.5 km from the landfill. Within this distance the assessed air pollutant concentration for several air pollutants was significantly above the World Health Organization reference lifetime exposure health criteria. Finally, the applied methodology was used in the Ano Liosia landfill, where atmospheric concentrations of pollutants measured in the field were compared with model predictions.     

Incineration technology for managing biomedical wastes

Incineration of biomedical wastes is the preferred option in many areas. Wastes from hospitals are frequently incinerated on site, but current air pollution limits are difficult to comply with in small incinerators. The problems arising from incineration and the methods used to deal with them are summarized. A case is made for regional biomedical waste incinerators in the U.S.A.     

Current status of waste to power generation in Japan and resulting reduction of carbon dioxide emissions

We discuss the current status of waste to power generation (WPG) in Japan and various scenarios involving indirect reduction of carbon dioxide emissions by WPG. The number of WPG facilities domestically as of 2005 was 286. Power generation capacity attained 1,515 MW and power generation 7,050 GWh/year. This amount substitutes energy otherwise acquired from natural resources such as fossil fuels in thermal power plants. If the basic unit of carbon dioxide is 0.555 kg-CO₂/kWh, then the corresponding carbon dioxide emission reduction is calculated to be 3.9 million tons, equivalent to 26.7% of the 14.6 million tons emitted by municipal solid waste incinerators (MSWI) in 2005. Using various existing technological options, the power generation efficiency could reach more than 20% in MSWI facilities with capacity of 300 tons/day, although present efficiency is only 12.0%. If about 85% of MSW were incinerated in MSWI with power generation efficiency of 20% as a feasible assumption, the total power generation and the corresponding carbon dioxide reduction would be 16,540 GWh/year and 9.18 million tons, respectively, equivalent to 62.7% of the carbon dioxide emitted by MSWI. Also, the ratio of the additional reduction of carbon dioxide emissions by WPG to the total additional reduction (20,000 ktons/year) in Japan during the first commitment period would be 26.3%, suggesting that promotion of WPG in MSWI is an effective option for prevention of global warming.     

Role of waste management with regard to climate protection: a case study.

According to the Kyoto Protocol and the burden-sharing agreement of the European Union, Austria is required to cut greenhouse gas (GHG) emissions during the years 2008 to 2012 in order to achieve an average reduction of 13%, based on the level of emissions for the year 1990. The present contribution gives an overview of the history of GHG emission regulation in Austria and identifies the progress made towards the realization of the national climate strategy to attain the GHG emission targets. The contribution uses Austria as an example of the way in which proper waste management can help to reduce GHG emissions. The GHG inventories show that everything must be done to minimize the carbon input due to waste deposition at landfill sites. The incineration of waste is particularly helpful in reducing GHG emissions. The waste-to-energy by incineration plants and recovery of energy yield an ecologically proper treatment of waste using state-of-the-art techniques of a very high standard. The potential for GHG reduction of conventional waste treatment technologies has been estimated by the authors. A growing number of waste incinerators and intensified co-incineration of waste in Austrian industry will both help to reduce national GHG emissions substantially. By increasing the number and capacity of plants for thermal treatment of waste the contribution of proper waste management to the national target for reduction of GHG emissions will be in the range of 8 to 14%. The GHG inventories also indicate that a potential CO2 reduction of about 500 000 t year(-1) is achievable by co-incineration of waste in Austrian industry.