Laboratory migration experiments with radionuclides and natural colloids in a granite fracture

Natural colloids in groundwater could facilitate radionuclide transport, provided the colloids are mobile, are present in sufficient concentrations and can adsorb radionuclides. This paper describes the results of a laboratory migration study carried out with combinations of radionuclides and natural colloids within a fracture in a large granite block to experimentally determine the impact of colloids on radionuclide transport. The 85Sr used in this study is an example of a moderately sorbing radionuclide, while the 241Am is typical of a strongly sorbed radionuclide with very low solubility. The natural colloids used in this study were isolated from granite groundwater from Atomic Energy of Canada (AECL) Underground Research Laboratory (URL), and consisted of mostly 1-10 nm organic colloids, along with lesser amounts of 10-450 nm colloids (organics and aluminosilicates). The measured coefficients for radionuclide sorption onto these colloids were between 3 x 10(2) and 1 x 10(3) ml/g for 85Sr, and between 7 x 10(4) and 7 x 10(5) mg/l for 241Am. The 85Sr sorption on the natural colloids appeared to be reversible. Migration experiments in the granite block were carried out by establishing a flow field between two boreholes (out of a total of nine) intersecting a main horizontal fracture. These experiments showed that dissolved 85Sr behaved as a moderately sorbing tracer, while dissolved 241Am was completely adsorbed by the fracture surfaces and showed no evidence of transport. However, when natural colloids were injected together with dissolved 241Am, a small amount of 241Am transport was observed, demonstrating the ability of natural colloids to facilitate the transport of radionuclides with low solubility. Natural colloids had only a minor effect on the transport of 85Sr. In a separate experiment to test the effect of higher colloid concentrations on 85Sr migration, synthetic colloids were produced from Avonlea bentonite. The introduction of a relatively high concentration of bentonite colloids actually reduced 85Sr transport because, compared to natural colloids, the bentonite colloids were less mobile and they sorbed 85Sr more strongly.     

Colloid-facilitated transport of radionuclides through fractured media

The sorption of radionuclides on natural colloids may significantly modify their transport behaviour through fractured media, since radionuclides bound to colloids may not be subject to the important retardation mechanisms of matrix diffusion and sorption onto pore surfaces. This paper reports on theoretical and experimental work aimed at assessing the relevance of colloid-facilitated transport to repository safety analyses, with specific reference to the Swiss case. Transport models are presented, developed in conjunction with field- and laboratory-based studies of deep groundwater in the crystalline basement of northern Switzerland, in which colloid size distributions, compositions and sorption properties have been measured. Various potential mechanisms giving rise to both reversible and irreversible sorption are discussed. In the first case, a simple approach is examined which is based on previously reported models of colloid transport and assumes reversible, linear sorption on colloids, for which experimental data have been obtained. It is shown that transport of radionuclides would not, in general, be significantly enhanced because of this process. A more recently developed and more complex model is then described incorporating irreversible sorption, in which case the transport of radionuclides tends to be strongly dependent on the extent of colloid-fracture wall interaction.     

Preliminary 3-D site-scale studies of radioactive colloid transport in the unsaturated zone at Yucca Mountain,Nevada

The U.S. Department of Energy (DOE) is actively investigating the technical feasibility of permanent disposal of high-level nuclear waste in a repository to be situated in the unsaturated zone (UZ) at Yucca Mountain (YM), Nevada. In this study we investigate, by means of numerical simulation, the transport of radioactive colloids under ambient conditions from the potential repository horizon to the water table. The site hydrology and the effects of the spatial distribution of hydraulic and transport properties in the Yucca Mountain subsurface are considered. The study of migration and retardation of colloids accounts for the complex processes in the unsaturated zone of Yucca Mountain, and includes advection, diffusion, hydrodynamic dispersion, kinetic colloid filtration, colloid straining, and radioactive decay. The results of the study indicate that the most important factors affecting colloid transport are the subsurface geology and site hydrology, i.e., the presence of faults (they dominate and control transport), fractures (the main migration pathways), and the relative distribution of zeolitic and vitric tuffs. The transport of colloids is strongly influenced by their size (as it affects diffusion into the matrix, straining at hydrogeologic unit interfaces, and transport velocity) and by the parameters of the kinetic-filtration model used for the simulations. Arrival times at the water table decrease with an increasing colloid size because of smaller diffusion, increased straining, and higher transport velocities. The importance of diffusion as a retardation mechanism increases with a decreasing colloid size, but appears to be minimal in large colloids.     

Transport of a non-volatile contaminant in unsaturated porous media in the presence of colloids

Stable colloidal particles can travel long distances in subsurface environments and carry particle-reactive contaminants with them to locations further than predicted by the conventional advective-dispersive transport equation. When such carriers exist in a saturated porous medium, the system can be idealized as consisting of three phases: an aqueous phase, a carrier phase, and a stationary solid matrix phase. However, when colloids are present in an unsaturated porous medium, the system representation should include one more phase, i.e. the air phase. In the work reported, a mathematical model was developed to describe the transport and fate of the colloidal particles and a non-volatile contaminant in unsaturated porous media. The model is based on mass balance equations in a four-phase porous medium. Colloid mass transfer mechanisms among aqueous, solid matrix, and air phases, and contaminant mass transfer between aqueous and colloid phases are represented by kinetic expressions. Governing equations are non-dimensionalized and solved to investigate colloid and contaminant transport in an unsaturated porous medium. A sensitivity analysis of the transport model was utilized to assess the effects of several parameters on model behavior. The colloid transport model matches successfully with experimental data of Wan and Wilson. The presence of air-water interface retards the colloid transport significantly counterbalancing the facilitating effect of colloids. However, the retardation of contaminant transport by colloids is highly dependent on the properties of the contaminant and the colloidal surface.     

Influence of the colloid type on the transfer of 60Co and 85Sr in silica sand column under varying physicochemical conditions

The influence of two types of colloids (natural organic matter, NOM), a colloid with high affinity for radionuclides (RN(s)), and hydrophilic synthetic latex (SHL), a colloid with low affinity for RN(s) on the transfer of (60)Co and (85)Sr in a silica sand column was studied under different physicochemical conditions: pH (4.9), ionic strength (10(-3) M and 10(-2) M), concentration of colloids (100 mg l(-1), 10 mg l(-1)), flow velocity (12.4 cm h(-1) and 3.7 cm h(-1)), water saturation of the column (100% and 70%). In the absence of colloids, the transfer of (60)Co and (85)Sr was retarded compared to the transfer of the conservative tracer. In the presence of colloids and according to the specific physicochemical conditions, an acceleration or retardation of (60)Co and (85)Sr transfer was observed compared to their transfer in the absence of colloids. Our results evidenced that any colloids even with low reactivity could significantly modify the RN transfer. However, the extent to which the transfer was influenced differs according to the colloid type; the NOM exhibiting higher impact than SHL. Batch experiments helped in interpreting of the interactions between the colloids, RN(s) and solid phase observed in column.     

Migration of colloids in discretely fractured porous media: effect of colloidal matrix diffusion

Numerical simulations of colloid transport in discretely fractured porous media were performed to investigate the importance of matrix diffusion of colloids as well as the filtration and remobilization of colloidal particles in both the fractures and porous matrix. To achieve this objective a finite element numerical code entitled COLDIFF was developed. The processes that COLDIFF takes into account include advective-dispersive transport of colloids, filtration and remobilization of colloidal particles in both fractures and porous matrix, and diffusive interactions of colloids between the fractures and porous matrix. Three sets of simulations were conducted to examine the importance of parameters and processes controlling colloid migration. First, a sensitivity analysis was performed using a porous block containing a single fracture to determine the relative importance of various phenomenological coefficients on colloid transport. The primary result of the analysis showed that the porosity of the matrix and the process of colloid filtration in fractures play important roles in controlling colloid migration. Second, simulations were performed to replicate and examine the results of a laboratory column study using a fractured shale saprolite. Results of this analysis showed that the filtration of colloidal particles in the porous matrix can greatly affect the tailing of colloid concentrations after the colloid source was removed. Finally, field-scale simulations were performed to examine the effect of matrix porosity, fracture filtration and fracture remobilization on long-term colloid concentration and migration distance. The field scale simulations indicated that matrix diffusion and fracture filtration can significantly reduce colloid migration distance. Results of all three analyses indicated that in environments where porosity is relatively high and colloidal particles are small enough to diffuse out of fractures, the characteristics of the porous matrix that affect colloid transport become more important than those of the fracture network. Because the properties of the fracture network tend to have greater uncertainty due to difficulties in their measurement relative to those of the porous matrix, prediction uncertainties associated with colloid transport in discretely fractured porous media may be reduced.     

The concentration, apparent molecular weight and chemical reactivity of silica from groundwater in southern Nevada

Sorption of radionuclides, metals and organic compounds to colloidal particles has been suggested to increase the mobility of these pollutants in groundwater. Because silicates and alumino-silicates can be important components of groundwater colloids, we have conducted a study to characterize the nature of silica in various springs and wells in Southern Nevada and to determine the extent that silica may be associated with colloidal particles that can participate in pollutant transport. The total silica content was measured using inductively coupled plasma emission spectroscopy (ICP). In addition, reactive silica was measured using the silica molybdate colorimetric technique. The apparent molecular weight of the silica was investigated using split-flow-lateral-transport-thin-cell-fractionation (SPLITT) which can readily distinguish between colloidal and low molecular weight associations. This study indicates that silica does not tend to form stable inorganic colloids in Southern Nevada groundwaters but exists as low molecular weight species. However, water from one of the test facilities on the Nevada Test Site (NTS) did contain stable siliceous colloids that could have important implications for the modeling the transport of radionuclides at this site.     

Field-scale colloid migration experiments in a granite fracture

An understanding of particle migration in fractured rock, required to assess the potential for colloid-facilitated transport of radionuclides, can best be evaluated when the results of laboratory experiments are demonstrated in the field. Field-scale migration experiments with silica colloids were carried out at AECL's Underground Research Laboratory (URL), located in southern Manitoba, to develop the methodology for large-scale migration experiments and to determine whether colloid transport is possible over distances up to 17 m. In addition, these experiments were designed to evaluate the effects of flow rate and flow path geometry, and to determine whether colloid tracers could be used to provide additional information on subsurface transport to that provided by conservative tracers alone. The colloid migration studies were carried out as part of AECL's Transport Properties in Highly Fractured Rock Experiment, the objective of which was to develop and demonstrate methods for evaluating the solute transport characteristics of zones of highly fractured rock. The experiments were carried out within fracture zone 2 as two-well recirculating, two-well non-recirculating, and convergent flow tests, using injection rates of 5 and 10 1 min⁻¹. Silica colloids with a 20 nm size were used because they are potentially mobile due to their stability, small size and negative surface charge. The shapes of elution profiles for colloids and conservative tracers were similar, demonstrating that colloids can migrate over distances of 17 m. The local region of drawdown towards the URL shaft affected colloid migration and, to a lesser extent, conservative tracer migration within the flow field established by the two-well tracer tests. These results indicate that stable colloids, with sizes as small as 20 nm, have different migration properties from dissolved conservative tracers. - 1997 Atomic Energy of Canada.     

Modeling colloid-facilitated transport of multi-species contaminants in unsaturated porous media

Colloid-facilitated transport has been recognized as a potentially important and overlooked contaminant transport process. In particular, it has been observed that conventional two phase sorption models are often unable to explain transport of highly sorbing compounds in the subsurface appropriately in the presence of colloids. In this study a one-dimensional model for colloid-facilitated transport of chemicals in unsaturated porous media is developed. The model has parts for simulating coupled flow, and colloid transport and dissolved and colloidal contaminant transport. Richards' equation is solved to model unsaturated flow, and the effect of colloid entrapment and release on porosity and hydraulic conductivity of the porous media is incorporated into the model. Both random sequential adsorption and Langmuir approaches have been implemented in the model in order to incorporate the effect of surface jamming. The concept of entrapment of colloids into the air-water interface is used for taking into account the effect of retardation caused due to existence of the air phase. A non-equilibrium sorption approach with options of linear and Langmuir sorption assumptions are implemented that can represent the competition and site saturation effects on sorption of multiple compounds both to the solid matrix and to the colloidal particles. Several demonstration calculations are performed and the conditions in which the non-equilibrium model can be approximated by an equilibrium model are also studied.     

Anomalous transport of colloids and solutes in a shear zone

Transport experiments with colloids and radionuclides in a shear zone were conducted during the Colloid and Radionuclide Retardation experiment (CRR) at Nagra's Grimsel Test Site. Breakthrough curves of bentonite colloids and uranine, a non-sorbing solute, were measured in an asymmetric dipole flow field. The colloid breakthrough is earlier than that of uranine. Both breakthrough curves show anomalously long late time tails and the slope of the late time tails for the colloids is slightly higher. Anomalous late time tails are commonly associated with matrix diffusion processes; the diffusive interaction of solutes transported in open channels with the adjacent porous rock matrix or zones of stagnant water. The breakthrough curves for different colloid size classes are very similar and show no signs of fractionation due to their (size-dependent) diffusivity. It is proposed that tailing of the colloids is mainly caused by the structure of the flow field and that for the colloid transport, matrix diffusion is of minor importance. This has consequences for the interpretation of the uranine breakthrough. Comparisons of experimental results with numerical studies and with the evaluation of the colloid breakthrough with continuous time random theory imply that the tailing in the conservative solute breakthrough in this shear zone is not only caused by matrix diffusion. Part of the tailing can be attributed to advective transport in fracture networks and advection in low velocity regions. Models based on the advection-dispersion equation and matrix diffusion do not properly describe the temporal and spatial evolution of colloid and solute transport in such systems with a consistent set of parameters.     

Strontium migration in a crystalline medium: effects of the presence of bentonite colloids

The effects of bentonite colloids on strontium migration in fractured crystalline medium were investigated. We analyzed first the transport behaviour of bentonite colloids alone at different flow rates; then we compared the transport behaviour of strontium as solute and of strontium previously adsorbed onto stable bentonite colloids at a water velocity of approximately 7.1·10(-6)m/s-224m/yr. Experiments with bentonite colloids alone showed that - at the lowest water flow rate used in our experiments (7.1·10(-6)m/s) - approximately 70% of the initially injected colloids were retained in the fracture. Nevertheless, the mobile colloidal fraction, moved through the fracture without retardation, at any flow rate. Bentonite colloids deposited over the fracture surface were identified during post-mortem analyses. The breakthrough curve of strontium as a solute, presented a retardation factor, R(f)~6, in agreement with its sorption onto the granite fracture surface. The breakthrough curve of strontium in the presence of bentonite colloids was much more complex, suggesting additional contributions of colloids to strontium transport. A very small fraction of strontium adsorbed on mobile colloids moved un-retarded (R(f)=1) and this fraction was much lower than the expected, considering the quantity of strontium initially adsorbed onto colloids (90%). This behaviour suggests the hypothesis of strontium sorption reversibility from colloids. On the other hand, bentonite colloids retained within the granite fracture played a major role, contributing to a slower strontium transport in comparison with strontium as a solute. This was shown by a clear peak in the breakthrough curve corresponding to a retardation factor of approximately 20.     

Colloid facilitated transport of polychlorinated dibenzo-p-dioxins and dibenzofurans (PCDD/Fs) to the groundwater at Ma Da Area, Vietnam

PCDD/Fs are hydrophobic organic substances and strongly sorbing to soil particles. Once adsorbed to soil particles they are believed to be virtually immobile. However, research in the last decades confirmed that strong sorbing contaminants may reach the groundwater via colloid-facilitated transport. This pathway has not been investigated before in Vietnam. Ma Da area, 100 km north of Ho Chi Minh City, was repeatedly sprayed during the Vietnam War (1962–1971) with herbicides like Agent Orange containing, beside others, the teratogenic contaminant 2,3,7,8-tetrachlorodibenzo-p-dioxin (TCDD). 11 surface soil samples and 12 water samples were collected in Ma Da area for analysis of PCDD/Fs in solids. Soil TCDD concentrations ranged from 1–41 ppt with a mean of 8.8 ppt and a mean I-TEQ of 9.7 ppt. Two surface water samples showed colloid bound TCDD (7 and 19 ppt). Groundwater samples showed elevated colloid bound PCDD concentrations (mean 770 ng/kg), mainly octachlorodibenzo-p-dioxin. Groundwater colloids separated by filtration did not show any TCDD. The results support that TCDD/Fs can be relocated from the top soil to the groundwater by colloidal pathway. They did not provide evidence that the dioxins bound to groundwater colloids are leftovers from the Second Indochinese War. However, this study reinforces that the colloidal transport pathway has to be included investigating the relocation of strong sorbing organic contaminants.     

The kinetic stability of colloid-associated plutonium: settling characteristics and species transformation

The colloid-associated plutonium-239, as the dominant species of Pu in natural environment, was formed through sorption of Pu onto in situ colloids. In case of chemical perturbations present in pore water, the fate and transport of Pu would be therefore impacted by changes in sorption affinity of Pu for the colloid surfaces. The present study reveals that colloidal ²³⁹Pu exhibited the kinetic stability in two respects. First, in situ colloids isolated from the vadose zone sediments at Lop Nor, when in contact with solutions of high ion concentrations or low pH, were significantly aggregated and then exhibited fast settling. Kinetics settling characteristics were described by the parameters, including settling index and characteristic time. Second, Pu dissociation from colloid surfaces occurred immediately after the introduction of Na⁺. However, the dissolved species was still unstable and had the potential for re-association with the fraction of colloids that had not settled out from the suspensions due to small size and then remained in suspension. This implies that Pu sorption sites on initial colloids were changed to the sites of suspended colloids.     

A novel two-dimensional model for colloid transport in physically and geochemically heterogeneous porous media

A two-dimensional model for colloid transport in geochemically and physically heterogeneous porous media is presented. The model considers patchwise geochemical heterogeneity, which is suitable to describe the chemical variability of many surficial aquifers with ferric oxyhydroxide-coated porous matrix, as well as spatial variability of hydraulic conductivity, which results in heterogeneous flow field. The model is comprised of a transient fluid flow equation, a transient colloid transport equation, and an equation for the dynamics of colloid deposition and release. Numerical simulations were carried out with the model to investigate the colloid transport behavior in layered and randomly heterogeneous porous media. Results demonstrate that physical and geochemical heterogeneities markedly affect the colloid transport behavior. Layered physical or geochemical heterogeneity can result in distinct preferential flow paths of colloidal particles. Furthermore, the combined effect of layered physical and geochemical heterogeneity may result in enhanced or reduced preferential flow of colloids. Random distribution of physical heterogeneity (hydraulic conductivity) results in a random flow field and an irregularly distributed colloid concentration profile in the porous medium. Contrary to random physical heterogeneity, the effect of random patchwise geochemical heterogeneity on colloid transport behavior is not significant. It is mostly the mean value of geochemical heterogeneity rather than its distribution that governs the colloid transport behavior.     

Colloid and suspended particle migration experiments in a granite fracture

To determine the mobility of colloids (0.001–0.45 μm) and suspended particles (> 0.45 μm) in granite fractures, laboratory particle-migration and conservative tracer studies have been carried out in a natural fracture within a large granite block, with overall dimensions of 83×90×60 cm. Flow fields within this horizontal fracture were controlled through a set of 9 boreholes drilled orthogonally to the fracture. Laboratory experiments were performed using a range of average water velocities which contained values low enough to closely approximate the natural flow velocities of < 2 m yr⁻¹ in plutonic rocks of the Canadian Shield. The particles used had diameters between 0.02 and 22 μm, and included latex spheres, glass spheres and colloidal silica. Migration experiments were carried out with a filtered groundwater, ionic strength of 0.01 mol kg⁻¹, obtained from a granite fracture within the Whiteshell Research Area of Manitoba. Flushing experiments showed that suspended particles as large as 40 μm could be mobilized from the fracture surface. The mobility of suspended particles was significantly less than that of colloids. However, within the size range of colloids used in these studies (0.022–0.090 μm), colloid size did not affect colloid migration. Although, in general, colloids eluted ahead of the conservative tracer, colloid mobility was significantly reduced when the average groundwater velocity dropped below between 32 and 240 m yr⁻¹. Colloid transport was found to be very sensitive to flow path and flow direction.     

Analysis of colloid and tracer breakthrough curves

We consider the dispersion and elution of colloids and dissolved nonsorbing tracers within saturated heterogeneous porous media. Since flow path geometry in natural systems is often ill-characterized macroscopic (mean) flow rates and dispersion tensors are utilized in order to account for the sub-model scale microscopic fluctuations in media structure (and the consequent hydrodynamic profile). Even for tracer migration and dispersal this issue is far from settled.Here we consider how colloid and tracer migration phenomena can be treated consistently. Theoretical calculations for model flow geometries yield two quantitative predictions for the transport of free (not yet captured) colloids with reference to a non-sorbing dissolved tracer within the same medium: the average migration velocity of the free colloids is higher than that of the tracer; and that the ratio of the equivalent hydrodynamic dispersion rates of colloids and tracer is dependent only upon properties of the colloids and the porous medium, it is independent of pathlengths and fluid flux, once length scales are large enough.The first of these is well known, since even in simple flow paths free colloids must stay more centre stream. The second, if validated suggests how solute and colloid dispersion may be dealt with consistently in macroscopic migration models. This is crucial since dispersion is usually ill-characterized and unaddressed by the experimental literature. In this paper we present evidence based upon an existing Drigg field injection test for the validity of these predictions.We show that starting from experimental data the fitted dispersion rates of both colloids and non-sorbing tracers increase with the measured elution rates (obeying slightly different rules for tracers and colloids); and that the ratio of colloid and nonsorbing tracer elution rates, and the ratio of colloid and nonsorbing tracer dispersion rates may be dependent upon properties of the colloids and the medium (not the flow regime).It is important to realize that even for unretarded species, an earlier peak in the breakthrough curve does not necessarily correspond to a faster mean elution rate, or vice versa. But rather that a colloid may elute faster but disperse less than an equivalent tracer. Hence its peak may be retarded compared to that of the tracer, even assuming no retardation. Hence one must consider a combination of mean elution rate and mean dispersion rate, and not rely on “peak times” to corroborate chromatographic effects. The importance of this lies in the fact that these processes are not independent and yet upscale differently. Thus realistic estimates of effective colloid dispersion rates should be upscaled in a way consistent with that adopted for tracers within the same system.     

Colloid transport in a geochemically heterogeneous porous medium: aquifer tank experiment and modeling

To examine colloid transport in geochemically heterogeneous porous media at a scale comparable to field experiments, we monitored the migration of silica-coated zirconia colloids in a two-dimensional layered porous media containing sand coated to three different extents by ferric oxyhydroxides. Transport of the colloids was measured over 1.65 m and 95 days. Colloid transport was modeled by an advection-dispersion-deposition equation incorporating geochemical heterogeneity and colloid deposition dynamics (blocking). Geochemical heterogeneity was represented as favorable (ferric oxyhydroxide-coated) and unfavorable (uncoated sand) deposition surface areas. Blocking was modeled as random sequential adsorption (RSA). Release of deposited colloids was negligible. The time to colloid breakthrough after the onset of blocking increased with increasing ferric oxyhydroxide-coated surface area. As the ferric oxyhydroxide surface area increased, the concentration of colloids in the breakthrough decreased. Model-fits to the experimental data were made by inverse solutions to determine the fraction of surface area favorable for deposition and the deposition rate coefficients for the favorable (ferric oxyhydroxide-coated) and unfavorable sites. The favorable deposition rate coefficient was also calculated by colloid filtration theory. The model described the time to colloid breakthrough and the blocking effect reasonably well and estimated the favorable surface area fraction very well for the two layers with more than 1% ferric oxyhydroxide coating. If mica edges in the uncoated sand were considered as favorable surface area in addition to the ferric oxyhydroxide coatings, the model predicted the favorable surface area fraction accurately for the layer with less than 1% ferric oxyhydroxide coating.     

Actinide geochemistry: From the molecular level to the real system

Geochemical processes leading to either mobilization or retention of radionuclides in an aquifer system are significantly influenced by their interaction with rock, sediment and colloid surfaces. Therefore, a sound safety assessment of nuclear waste disposal requires the elucidation and quantification of those processes. State-of-the-art analytical techniques as e.g. laser- and X-ray spectroscopy are increasingly applied to study solid–liquid interface reactions to obtain molecular level speciation insight.We have studied the sorption of trivalent lanthanides and actinides onto aluminium oxides, hydroxides and purified clay minerals by the time-resolved laser fluorescence spectroscopy and X-ray-absorption spectroscopy. Chemical constitution and structure of surface bound actinides are proposed based on spectroscopic information. Open questions still remain with regard to the exact nature of mineral surface ligands and the mineral/water interface. Similarities of spectroscopic data obtained for M(III) sorbed onto γ-alumina, and clay minerals suggest the formation of very comparable inner-sphere surface complexes such as S–O–An(III)(OH)_x^(2 − x)(H₂O)_5 − x at pH > 5. Those speciation data are found consistent with those predicted by surface complexation modelling. The applicability of data obtained for pure mineral phases to actinide sorption onto heterogeneously composed natural clay rock is examined by experiments and by geochemical modelling. Good agreement of experiment and model calculations is found for U(VI) and trivalent actinide/lanthanide sorption to natural clay rock. The agreement of spectroscopy, geochemical modelling and batch experiments with natural rock samples and purified minerals increases the reliability in model predictions.The assessment of colloid borne actinide migration observed in various laboratory and field studies calls for detailed information on actinide–colloid interaction. Kinetic stabilization of colloid bound actinides can be due to inclusion into inorganic colloid matrix or by macromolecular rearrangement in case of organic, humic/fulvic like colloids. Only a combination of spectroscopy, microscopy and classical batch sorption experiments can help to elucidate the actinide–colloid interaction mechanisms and thus contribute to the assessment of colloids for radionuclide migration.     

Transport of reactive colloids and contaminants in groundwater: effect of nonlinear kinetic interactions

Transport of reactive colloids in groundwater may enhance the transport of contaminants in groundwater. Often, the interpretation of results of transport experiments is not a simple task as both reactions of colloids with the solid matrix and reactions of contaminants with the solid matrix and mobile and immobile colloids may be time dependent and nonlinear. Further colloid transport properties may differ from solute transport properties. In this paper, a one-dimensional model for coupled and contaminant in a porous medium (COLTRAP) is presented together with simulation results. Calculated breakthrough curves (BTC's) during contamination and decontamination show systematically the effect of nonlinear and kinetic interactions on contaminant transport in the presence of reactive colloids, and the effect of colloid transport properties that differ from solute transport properties. It is shown that in case of linear kinetic reactions, the rate of exchange of mobile and immobile colloids have a large impact on the shape of BTC's even if the solid matrix is saturated with respect to colloids. BTC's during the contamination and decontamination phase have identical shapes in this case. Moreover, the slow reactions of contaminants and colloids may lead to unretarded breakthrough of contaminants. Independent of reaction rates, nonlinear reactions lead to BTC's that are steeper during contamination than in the linear case. A characteristic aspect of nonlinear sorption is that shapes of BTC's differ during the contamination and decontamination phase. It has been observed that shapes of some of the simulated adsorption and desorption curves are similar as shapes found in experiments reported in literature. This stresses the importance of incorporating both kinetics and nonlinearity in models for coupled colloid and contaminant transport and the capability of COLTRAP to interpret experimental results. Finally, to figure out whether nonlinear processes play a role, it is very important to consider both contamination and decontamination in transport experiments.     

Numerical modeling of humic colloid borne americium (III) migration in column experiments using the transport/speciation code K1D and the KICAM model

The humic colloid borne Am(III) transport was investigated in column experiments for Gorleben groundwater/sand systems. It was found that the interaction of Am with humic colloids is kinetically controlled, which strongly influences the migration behavior of Am(III). These kinetic effects have to be taken into account for transport/speciation modeling. The kinetically controlled availability model (KICAM) was developed to describe actinide sorption and transport in laboratory batch and column experiments. Application of the KICAM requires a chemical transport/speciation code, which simultaneously models both kinetically controlled processes and equilibrium reactions. Therefore, the code K1D was developed as a flexible research code that allows the inclusion of kinetic data in addition to transport features and chemical equilibrium. This paper presents the verification of K1D and its application to model column experiments investigating unimpeded humic colloid borne Am migration. Parmeters for reactive transport simulations were determined for a Gorleben groundwater system of high humic colloid concentration (GoHy 2227). A single set of parameters was used to model a series of column experiments. Model results correspond well to experimental data for the unretarded humic borne Am breakthrough.