Chlorinated fluorenes and alkylfluorenes in bleached kraft pulp and pulp mill discharges

The occurrence and levels of polychlorinated fluorenes (PCFLs), methylfluorenes (C₁-PCFLs) and dimethylfluorenes (C₂-PCFLs) were studied by high resolution gas chromatography/high resolution mass spectrometry (HRGC/HRMS) in hardwood and softwood pulp, effluent and biosludge from a bleached kraft mill. Semiquantitative concentrations of these compounds were estimated using selected ion monitoring and a mass spectral resolution of 10,000. The identification of PCFLs and C₁-PCFLs was confirmed by the chlorination mixtures of fluorene and 2-methylfluorene.

Several congeners were found for each compound groups studied and isomer patterns were similar in bleached pulp and biosludge. The approximated sum levels of di- and trichloro isomers of PCFLs, C₁-PCFLs and C₂-PCFLs in the biosludge were about 2, 5 and 4 ng/g dry weight (dw), respectively. The levels of the corresponding compounds in the softwood pulp were 0.5, 0.8 and 0.2 ng/g dw, respectively. Of the studied compounds, only C₁-diCFLs (0.01 ng/g dw) were detected in the hardwood pulp. In the effluent, PCFLs were non-detectable, but traces of C₁-diCFLs (0.5 ng/L) and C₂-pentaCFLs (0.06 ng/L) were found. These were observed mainly as dissolved in the filtrate and not as particle-bound.     

Polychlorinated dibenzo-p-dioxins (PCDD) and polychlorinated dibenzofurans (PCDF) in emissions from an urban incineratop. 1. Average and peak values

Gas chromatography-low resolution mass spectrometry was used to quantitate PCDD and PCDF emitted from an urban incinerator. The amounts were determinated in 17 samples collected over 9 months. Wide variability in the different sample concentrations, ranging from 2.3 mg/h to 348 mg/h for PCDD and from 3.9 mg/h to 324 mg/h for the PCDF, was observed.     

Dioxin formation in pulp and paper mills of India

Samples of effluents, sludge, pulp, final products (paper) and soil were collected from the identified pulp and paper mills in India. The samples were analysed for 2,3,7,8-tetrachloro-dibenzo-p-dioxin (2,3,7,8-TCDD) and other dioxin congeners and precursors. Pulp and paper mills using chlorine for the bleaching process showed the presence of 2,3,7,8-TCDD in effluent samples. In the effluent and pulp samples from mills where chlorine dioxide was used as a bleaching agent, the 2,3,7,8-TCDD congener ranged from below the detection limit 0.05 to 0.12 ngL⁻¹/ngg⁻¹. The relative standard deviation of reproducibility and the percent recovery of 2,3,7,8-TCDD were 2.07 and 82.4% in pulp and 2.8 and 92% in effluent, respectively. The 1,3,6,8-TCDD was the only other major dioxin congener found in the treated and untreated effluent and sludge samples. However, dichlorobenzene, trichlorophenyl, and hexachlorobiphenyl were detected in all samples. The formation of dioxins can be minimised by replacing chlorine with chlorine dioxide in bleaching processes in pulp and paper mills.     

Changes in the nature of dissolved organics during pulp and paper mill wastewater treatment: a multivariate statistical study combining data from three analytical techniques

The paper-making process can produce large amounts of wastewater (WW) with high particulate and dissolved organic loads. Generally, in developed countries, stringent international regulations for environmental protection require pulp and paper mill WW to be treated to reduce the organic load prior to discharge into the receiving environment. This can be achieved by primary and secondary treatments involving both chemical and biological processes. These processes result in complex changes in the nature of the organic material, as some components are mineralised and others are transformed. In this study, changes in the nature of organics through different stages of secondary treatment of pulp and paper mill WW were followed using three advanced characterisation techniques: solid-state ¹³C nuclear magnetic resonance (NMR) spectroscopy, pyrolysis-gas chromatography mass spectrometry (py-GCMS) and high-performance size-exclusion chromatography (HPSEC). Each technique provided a different perspective on the changes that occurred. To compare the different chemical perspectives in terms of the degree of similarity/difference between samples, we employed non-metric multidimensional scaling. Results indicate that NMR and HPSEC provided strongly correlated perspectives, with 86 % of the discrimination between the organic samples common to both techniques. Conversely, py-GCMS was found to provide a unique, and thus complementary, perspective.     

Congener-specific concentrations and carbon stable isotope ratios (delta13C) of two technical toxaphene products (Toxaphene and Melipax)

In this study we compared the contribution of individual congeners and the ratios of stable carbon isotopes of two technical toxaphene products. The former US-American product Toxaphene was from 1978 and the East-German product Melipax from 1979. Both technical products showed the known complexity in GC/ECD measurements. Contributions of 24 peaks to each of the technical products were determined by gas chromatography in combination high resolution electron capture negative ion mass spectrometry (GC/ECNI-HRMS). The percentages of the compounds studied in the technical mixtures ranged from approximately 0.05% to approximately 2.5% but showed some individual differences. 2,2,5,5,8,9,9,10,10-nonachlorobornane (B9-1025 or P-62) was identified as a major congener in both mixtures. 2-Endo,3-exo,5-endo,6-exo,8,8,10,10-octachlorobornane (B8-1413 or P26) and 2-endo,3-exo,5-endo,6-exo,8,8,9,10,10-nonachlorobornane (B9-1679 or P-50) were found at similar concentration in both technical products. Identical amounts of Melipax or Toxaphene were combusted to CO2 in an element analyzer and their delta13C values were determined relative to the international standard Vienna PeeDee belemnite (VPDB). The mean delta13C values of both products varied by 2.8% (determined at two different locations) which is roughly one order of magnitude more than the precision obtained in repetitive analyses of the individual products. Thus, both investigated products could be unequivocally distinguished by stable isotope ratio mass spectrometry (IRMS). IRMS analyses may thus be a suitable tool for tracing back toxaphene residues in environmental and food samples to the one or both of the products.     

Application of GC-MS/MS for the analysis of PCDD/Fs in sewage effluents

The application of high resolution gas chromatography in combination with tandem mass spectrometry in an ion trap was tested to substitute the expensive high resolution mass spectrometry in analysing polychlorinated dibenzo-p-dioxins and furans in sewage effluents. In tandem mass spectrometry, a set of parameters has to be optimised in order to attain the required sensitivity. To the best of our knowledge, this is the first time a method development for analysing PCDD/Fs with GC-MS/MS in an ion trap is described in this detail. Nine parameters are varied, including isolation window, collision induced dissociation (CID) amplitude, CID time, acquisition mass range, broadband amplitude, CID bandwidth, modulation range, filament current and ion trap temperature. This technique can be adapted to other analytes. By this optimisation, limits of detection of 0.01-0.05 ng/l are obtained. With its selectivity and sensitivity, tandem mass spectrometry is a powerful tool for the determination of PCDD/Fs in water samples. 55 sewage effluent samples from Germany were analysed.     

Determination of 2,3,7,8-tetrachlorodibenzo-p-dioxin in fresh water fish

Validated sample preparation procedures and high resolution gas chromatography-high resolution mass spectrometry techniques were utilized for the quantitative measurement of 4 to 695 pg/g (ppt) levels of 2,3,7,8-tetrachlorodibenzo-p-dioxin (2378-TCDD) in the edible portions of fish from the state of Michigan. The methodology and the analytical results are presented.     

Evaluation of the treatment efficiencies of paper mill whitewaters in terms of organic composition and toxicity

The efficiency of several lab scale treatments (aerobic, anaerobic and ozone or combination of these) was evaluated using two packaging board mill whitewaters. The effect of the different treatments on the elimination of the organic load, the chemical oxygen demand (COD) and the toxicity was tested as well as the relationship between these parameters. Biocides, phenolic compounds, surfactants, plasticiziers and wood extractives were identified in untreated and treated whitewaters by liquid chromatography coupled with mass spectrometry (LC-MS) or gas chromatography coupled with mass spectrometry (GC-MS). A strong dependency on the water type and treatment efficiency was observed, being the combination of anaerobic and aerobic treatments the best option to reduce the organic contaminants in these waters, although in some cases, the toxicity did not decrease. However, ozone as post-treatment permitted a further reduction of organic compounds, toxicity and COD.     

Analysis of dioxins and furans in environmental samples by GC-ion-trap MS/MS

The work aims to characterise PCDDs/Fs in environmental matrices by high resolution gas chromatography coupled to low resolution quadrupole ion-trap mass spectrometry (GC-QITMS/MS). In particular, the study was mainly focused in different environmental samples such as sewage sludge, soils, and sediments and in combustion residues as fly ashes. Previous experiences have already detected and quantified PCDDs/PCDFs in all matrices studied. Moreover, isomer-specific analysis of 2,3,7,8-PCDDs/Fs compounds corroborated good correlation between GC-QITMS/MS and a well-established technique such as high resolution mass spectrometry (HRMS). Finally, QC measures included the participation in intercalibration exercises. Successful results were achieved using GC-QITMS/MS in the analysis of fly ashes, soils and sediment materials. In general, GC-QITMS/MS constitutes an interesting alternative for routine analysis of dioxins in such as matrices.     

BOD biosensors for pulp and paper industry wastewater analysis

Introduction

Two semi-specific microbial biosensors were constructed for the analysis of biochemical oxygen demand (BOD) in high-cellulose-content pulp and paper industry wastewaters. The biosensors were based on living cells of Bacillus subtilis and Paenibacillus sp. immobilized in an agarose gel matrix. Semi-specific microorganisms were isolated from various samples (decaying sawdust and rabbit manure) and were chosen based on their ability to assimilate cellulose.

Materials &; methods

The biosensors were calibrated with the Organization for Economic Cooperation and Development synthetic wastewater, and measurements with different wastewaters were conducted.

Results

The response time of biosensors using the steady-state method was 20?C25 min, and the service life of immobilized microorganisms was 96 days. Detection limit was 5 mg/l of BOD₇ while linear ranges extended up to 55 and 50 mg/l of the BOD₇ for B. subtilis- and Paenibacillus sp.-based biosensors, respectively. Repeatability and reproducibility of both biosensors were within the limits set by APHA??less than 15.4%. In comparison, both biosensors overestimated the BOD₇ values in paper mill wastewaters and underestimated the BOD₇ in aspen pulp mill wastewater.

Conclusions

The semi-specific biosensors are suitable for the estimation of organic pollution derived from cellulose, while the detection of pollution derived from tannins and lignins was minor. Better results in terms of accuracy and repeatability were gained with Paenibacillus sp. biosensor.     

Contents and origin of polychlorinated diphenyl ethers (PCDE) in salmon from the Baltic Sea, Lake Saimaa and the Tenojoki river in Finland

The presence of 26 congeners of polychlorinated diphenyl ethers (PCDEs) was investigated in salmon from three locations in Finland. In addition to salmon, one chlorophenol wood preservative (Ky-5) and one fly ash sample were analyzed for PCDEs. Concentrations of PCDE congeners in salmon muscle measured by high resolution gas chromatography/low resolution mass spectrometry ranged from < 0.02 to 2.4 ng/g fresh weight. The major components of tetra- to octachlorinated PCDEs in salmon were one TeCDE (22′44′-), two PeCDEs (22′44′5- and 23′44′5-) and three HxCDEs (22′44′56′-, 22′44′55′- and 22′344′5-). The Baltic salmon caught from the Simojoki River had higher levels of PCDEs than the Atlantic salmon from the Tenojoki River or salmon from Lake Saimaa in South-Finland. Same PCDE congeners which were abundant in the wood preservative were also detected in salmon, whereas PCDE congeners in the fly ash were different from those in salmon or in Ky-5.     

Metabolism of obeticholic acid in brown bullhead (Ameiurus nebulosus)

Environmental Science and Pollution Research - Analysis of brown bullhead (Ameiurus nebulosus) bile by ultra performance liquid chromatography high-resolution mass spectrometry (UPLC/HRMS) revealed...     

Electrospray Ionization Fourier Transform Ion Cyclotron Resonance Mass Spectrometry (ESI FT-ICR MS): Characterization of Complex Environmental Mixtures

Structural and chemical characterization of compounds within complex environmental mixtures provides unique insights into the roles of these compounds in different environmental processes. Here, an emerging technique in environmental chemistry, electrospray ionization Fourier transform ion cyclotron resonance mass spectrometry (ESI FT-ICR MS), is described and its applications to the molecular characterization of humic acids and petroleum products are reviewed and examined. ESI is a low-fragmentation ionization technique that preferentially ionizes polar functional groups prior to mass spectrometric analysis. This technique allows the characterization of intact polar macromolecules that are inaccessible to standard chromatographic techniques. ICR MS is an ultrahigh resolution and mass accuracy MS technique based on the detection of ion cyclotron motion within a magnetic field. The combination of ESI FT-ICR MS with other structural techniques such as nuclear magnetic resonance (NMR) allows the unprecedented identification and characterization of polar macromolecules in environmental mixtures and will find numerous applications within environmental chemistry and forensics.     

Electrospray Ionization Fourier Transform Ion Cyclotron Resonance Mass Spectrometry (ESI FT-ICR MS): Characterization of Complex Environmental Mixtures

Structural and chemical characterization of compounds within complex environmental mixtures provides unique insights into the roles of these compounds in different environmental processes. Here, an emerging technique in environmental chemistry, electrospray ionization Fourier transform ion cyclotron resonance mass spectrometry (ESI FT-ICR MS), is described and its applications to the molecular characterization of humic acids and petroleum products are reviewed and examined. ESI is a low-fragmentation ionization technique that preferentially ionizes polar functional groups prior to mass spectrometric analysis. This technique allows the characterization of intact polar macromolecules that are inaccessible to standard chromatographic techniques. ICR MS is an ultrahigh resolution and mass accuracy MS technique based on the detection of ion cyclotron motion within a magnetic field. The combination of ESI FT-ICR MS with other structural techniques such as nuclear magnetic resonance (NMR) allows the unprecedented identification and characterization of polar macromolecules in environmental mixtures and will find numerous applications within environmental chemistry and forensics.     

Some factors influencing EROD activity in winter flounder (Pleuronectes americanus) exposed to effluent from a pulp and paper mill

EROD (ethoxyresorufin-O-deethylase) activity was determined in winter flounder, a sediment-inhabiting and non-migratory fish species, living near a pulp and paper mill in Newfoundland in relation to temperature, gender, sexual maturity, and lesions in the liver. Samples of liver were taken from fish captured by SCUBA divers at 0 degrees C, 5 degrees C and 16 degrees C. Enzymic activity was detected in fish living only above 0 degrees C. Adult males and juvenile fish had higher levels of EROD activity than prespawning females at 5 degrees C. Macrophage aggregates only or occurring simultaneously with bile ductule hyperplasia and clear cell foci in the liver, did not impair EROD activity but necrosis had a negative effect. Results from this study indicate the importance of water temperature, gender, sexual maturity and liver pathology in assessing EROD activity of fish in biomonitoring programs.     

Identification of arsenobetaine in sole,lemon sole,flounder, dab,carb and shrimps by field desorption and fast atom bombardment mass spectrometry

Organo-arsenic has been isolated from sole, lemon sole, flounder, dab, crab and shrimps by extraction or ion-exchange in combination with thin-layer chromatography. An alkaline digestion of the samples, followed by a reduction with sodiumborohydride leads to the formation of trimethylarsine. The behaviour of the organo-arsenic compound was very similar to that of synthesized arsenobetaine. Field desorption mass spectrometry (FDMS) can be used to identify arsenobetaine in the isolates. Sufficient purification by thin-layer chromatography is found to be a prerequisite for the detection of a protonated molecular ion of arsenobetaine. If this situation is not met acid enhanced FDMS or Fast Atom Bombardment mass spectrometry in high resolution can be used successfully.     

Investigation of pathogenic Escherichia coli and microbial pathogens in pulp and paper mill biosolids.

Biosolids produced from pulp and paper mill wastewater treatment have excellent properties as soil conditioners, but often contain high levels of Escherichia coli. E. coli are commonly used as indicators of fecal contamination and health hazard; therefore, their presence in biosolids causes concern and has lead to restrictions in land-spreading. The objectives of this study were to determine the following: (1) if E. coli from the biosolids of a wastewater-free pulp and paper mill were enteric pathogens, and (2) if other waterborne microbial pathogens were present. E. coli were screened for heat-labile and heat-stable enterotoxin and verocytotoxin virulence genes using a polymerase chain reaction. Ten isolates were also screened for invasion-associated locus and invasion plasmid antigen H genes. None of the 120 isolates carried these genes. Tests for seven other microbial pathogens were negative. Effluents and biosolids from this mill do not contain common microbial pathogens and are unlikely to pose a health hazard.     

Model compound synthesis for the structure determination of new unknown planar aromatic compounds originating from pulp mill

Several model compounds have been synthesized for verification of the structures of new unknown planar aromatic compounds (UPACs) observed in high-resolution gas chromatography/low-resolution mass spectrometry analyses of the polychlorodibenzodioxins (PCDDs) and polychlorodibenzofurans (PCDFs) in pulp mill products, effluents, sediments and mussels. The mass spectra of synthetic alkyl polychlorodibenzofurans (C₆-PCDFs) were different, but those of alkyl polychlorobibenzyls (C₅-PCBBs) were very similar compared to the spectra of UPACs.     

Levels of 3,3′,4,4′-tetrachloroazobenzene in herbicides and bulk reagents

The contamination levels of different commercial herbicides and bulk reagents with the carcinogen 3,3′,4,4′-tetrachloroazobenzene (TCAB) were determined by high resolution mass spectrometry. The concentrations vary from 0.00071 to 2.8 ug/g (ppm) for the herbicides and from 0.085 to 14 ug/g for the bulk reagents. They are thus lower than those of other reports.     

Extractability of trace elements in precipitated calcium carbonate (PCC) waste from an integrated pulp and paper mill complex

From the utilization point of view, it is notable that the total element concentrations in the precipitated calcium carbonate (PCC) waste were significantly lower than the maximal allowable heavy metal concentrations for fertilizers used in agriculture and in forestry, set on the basis of the EU and Finnish legislation. The easily soluble Ca concentration of 168.5g kg(-1) (d.w.) in PCC waste was 105 times higher than the typical value of 1.6g kg(-1) (d.w.) in the coarse mineral soil in Finland indicates that the PCC waste is a potential agent for soil remediation and for improving soil fertility if it is used as fertilizer. According to a five-stage sequential extraction procedure, the highest concentrations of most of the elements occurred either in HF+HNO3+HCl or H2O2+CH3COONH4 fraction. This means that the major part of the elements retained in the PCC waste are not easy to extract (leach) under conditions normally found in nature. This is beneficial since, if inorganic materials and by-products are utilized in earth construction, the content of harmful compounds must be low and the harmful components must be tightly bound to the matrix.