Concentrations of chlorine, bromine and iodine in Japanese rivers

Concentrations of halogens (Cl, Br and I) in 30 Japanese rivers were measured by ion chromatography and inductively coupled plasma mass spectrometry to understand their behavior in the terrestrial environment. Concentrations of Cl, Br and I in each river, obtained at 10 sampling points from the upper stream to the river mouth, tended to increase near the river mouth. The ranges of geometric means of Cl, Br and I in each river were 1.0–19.4 mg l⁻¹, 2.5–67.9 μg l⁻¹, and 0.18–8.34 μg l⁻¹, respectively. To compare halogen behavior, the concentration ratios, Br/Cl and I/Cl, were calculated. The Br/Cl range was (2.3–7.8) × 10⁻³ (geometric mean: 3.74 × 10⁻³), and it was nearly constant except for the Yoneshiro river. It was estimated that 60–80% of total Br in the middle to lower parts of this river was the excess Br. The Br chemical form in all the rivers is generally considered to be Br⁻. The I/Cl ratios had different trends in rivers flowing into the Japan Sea and Pacific Ocean, possibly due to the different geological features in the river catchments.     

Fate of cancerostatic platinum compounds in biological wastewater treatment of hospital effluents

The present work focuses on the fate of two cancerostatic platinum compounds (CPC), cisplatin and carboplatin, as well as of two inorganic platinum compounds, [PtCl₄]²⁻ and [PtCl₆]²⁻ in biological wastewater treatment. Laboratory experiments modelling adsorption of these compounds onto activated sludge showed promising specific adsorption coefficients K_D and K_OC and Freundlich adsorption isotherms. However, the adsorption properties of the investigated substances were differing significantly. Adsorption decreased following the order cisplatin > [PtCl₆]²⁻ > [PtCl₄]²⁻ > carboplatin. Log K_D-values were ranging from 2.5 to 4.3 , log K_OC from 3.0 to 4.7.

A pilot membrane bioreactor system (MBR) was installed in a hospital in Vienna and fed with wastewater from the oncologic in-patient treatment ward to investigate CPC-adsorption in a sewage treatment plant. During three monitoring periods Pt-concentrations were measured in the influent (3–250 μg l⁻¹ Pt) and the effluent (2–150 μg l⁻¹ Pt) of the treatment plant using ICP-MS. The monitoring periods (duration 30 d) revealed elimination efficiencies between 51% and 63% based on averaged weekly input–output budgets. The derived log K_D-values and log K_OC-values ranged from 2.4 to 4.8 and from 2.8 to 5.3, respectively. Species analysis using HPLC-ICP-MS proofed that mainly carboplatin was present as intact drug in the influent and – due to low log K_D – in the effluent of the MBR.     

UV-H2O2 based AOP and its integration with biological activated carbon treatment for DBP reduction in drinking water

The presence of disinfection byproducts (DBPs) such as trihalomethanes (THMs) and haloacetic acids (HAAs) in drinking water is of great concern due to their adverse effects on human health. Emerging regulation limiting the concentration of DBPs in drinking water has increased demands for technologies and processes which reduce the formation of DBPs in drinking water. In this study, UV-H₂O₂ based advance oxidation process (AOP) was used to treat raw surface water. Experiments were conducted using low pressure mercury vapor UV lamps in collimated beam and flow-through annular photoreactors. The effect of UV fluence (0–3500 mJ cm⁻²) and hydrogen peroxide concentration (0–23 mg l⁻¹) in reducing the concentration of THMs and HAAs was examined. The UV-H₂O₂ AOP was then coupled with a downstream biological activated carbon (BAC) treatment to assess the synergetic benefits of combining the two treatments. It was observed that UV-H₂O₂ AOP was only effective at reducing DBPs at UV fluences of more than 1000 mJ cm⁻²and initial H₂O₂ concentrations of about or greater than 23 mg l⁻¹. However, the combined AOP–BAC treatment showed significant reductions of 43%, 52%, and 59% relative to untreated raw water for DBPs, TOC, and UV₂₅₄, respectively.     

Octyl and nonylphenol ethoxylates and carboxylates in wastewater and sediments by liquid chromatography/tandem mass spectrometry

This work presents an LC–MS–MS-based method for the quantitation of nonylphenol ethoxylates (NPEOs) and octylphenol ethoxylates (OPEOs) in water, sediment, and suspended particulate matter, and three of their carboxylated derivatives in water. The alkylphenol ethoxylates (APEOs) were analyzed using isotope dilution mass spectrometry with [¹³C₆]-labeled analogues, whereas the carboxylated derivatives were determined by external standard quantitation followed by confirmation using standard additions. The method was used to study APEO’s behavior in a wastewater treatment plant (WWTP), where total dissolved NP0-16EO concentration was reduced by approximately 99% from influent (390 μg l⁻¹) to final effluent (4 μg l⁻¹), and total OP0-5EO concentration decreased by 94% from 3.1 to 0.2 μg l⁻¹. In contrast, the carboxylated derivatives were formed during the process with NP0-1EC concentrations increasing from 1.4 to 24 μg l⁻¹. Short-chain APEOs were present in higher proportions in particulate matter, presumably due to greater affinity for solids compared to the long-chain homologues. NP (0.49 μg l⁻¹) and NP0-1EC (4.8 μg l⁻¹) were the only APEO-related compounds detected in a surface water sample from a WWTP-impacted estuary; implying that 90% of the mass was in the form of carboxylated derivatives. Sediment analysis showed nonylphenol to be the single most abundant compound in sediments from the Baltimore Harbor area, where differences in homologue distribution suggested the presence of treated effluent in some of the sites and non-treated sources in the rest.     

Leaching and degradation of 21 pesticides in a full-scale model biobed

Filling and cleaning of pesticide sprayers presents a potential risk of pollution of soil and water. Three different solutions for handling sprayers have been suggested: Filling and cleaning in the field, filling and cleaning on hard surfaces with collection of the waste water, and filling and cleaning on a biobed, which is an excavation lined with clay and filled with a mixture of chopped straw, sphagnum and soil with turf on top, and with increased sorption capacity and microbial activity for degradation of the pesticides. In the present study the degradation and leaching of 21 pesticides (5 g of each) was followed in an established full-scale model biobed. Percolate was collected and analysed for pesticide residues, and the biobed material was sampled at three different depths and analysed by liquid chromatography double mass spectrometry (LC-MSMS). During the total study period of 563 days, no traces of 10 out of 21 applied pesticides were detected in the percolate (detection limits between 0.02 and 0.9 μg l⁻¹) and three pesticides were only detected once and at concentrations below 2 μg l⁻¹. During the first 198 days before second application, 14% of the applied herbicide bentazone was detected in the leachate with maximum and mean concentrations of 445 and 172 μg l⁻¹, respectively. About 2% of the initial mecoprop and fluazifop dose was detected in the percolate, with mean concentrations of 23 μg l⁻¹, while MCPA and dimethoate had mean concentrations of 3.5 and 4.7 μg l⁻¹, respectively. Leachate concentrations for the remaining pesticides were generally below the detection limit (0.02–0.9 μg l⁻¹, below 1% of applied). Sorption studies of five pesticides showed that compounds with a low K_d value appeared in the leachate. After 169 days, all pesticides in the biobed profile were degraded to a level below 50% of the calculated initial dose. Pesticides with K_oc values above 100 were primarily found in the uppermost 10 cm and degraded slowest due to the low bioavailability. The 11 most degradable pesticides were all degraded such that less than 3% remained in the biobed after 169 days.

Following second pesticide application of the biobed, leachate was sampled 215 and 365 days after the treatment. This showed the same pesticides to be leached out and at concentrations comparable to those of the first treatment. The same pesticides as after the first treatment were retained in the biobed.     

Assessment of toxicity of a glyphosate-based formulation using bacterial systems in lake water

A new Aeromonas bioassay is described to assess the potential harmful effects of the glyphosate-based herbicide, Roundup^®, in the Albufera lake, a protected area near Valencia. Viability markers as membrane integrity, culturability and β-galactosidase production of Aeromonas caviae were studied to determine the influence of the herbicide in the bacterial cells. Data from the multifactor analysis of variance test showed no significant differences (P > 0.05) between A. caviae counts of viability markers at the studied concentrations (0, 50 and 100 mg l⁻¹ of glyphosate).

The effects of Roundup^® on microbial biota present in the lake were assessed by measuring the number of indigenous mesophilic Aeromonas in presence of different amounts of the herbicide at 0, 50 and 100 mg l⁻¹ of glyphosate. In samples containing 50 and 100 mg l⁻¹ of glyphosate a significant (P < 0.05) increase in Aeromonas spp. counts and accompanying flora was observed.

The acute toxicity of Roundup^® and of Roundup^® diluted with Albufera lake water to Microtox^® luminescent bacterium (Vibrio fischeri) also was determined. The EC₅₀ values obtained were 36.4 mg l⁻¹ and 64.0 mg l⁻¹ of glyphosate respectively. The acidity (pH 4.5) of the herbicide formulation was the responsible of the observed toxicity.     

Arsenic removal from water employing heterogeneous photocatalysis with TiO2 immobilized in PET bottles

Arsenic oxidation (As(III) to As(V)) and As(V) removal from water were assessed by using TiO₂ immobilized in PET (polyethylene terephthalate) bottles in the presence of natural sunlight and iron salts. The effect of many parameters was sequentially studied: TiO₂ concentration of the coating solution, Fe(II) concentration, pH, solar irradiation time; dissolved organic carbon concentration. The final conditions (TiO₂ concentration of the coating solution: 10%; Fe(II): 7.0 mg l⁻¹; solar exposure time: 120 min) were applied to natural water samples spiked with 500 μg l⁻¹ As(III) in order to verify the influence of natural water matrix. After treatment, As(III) and total As concentrations were lower than the limit of quantitation (2 μg l⁻¹) of the voltammetric method used, showing a removal over 99%, and giving evidence that As(III) was effectively oxidized to As(V). The results obtained demonstrated that TiO₂ can be easily immobilized on a PET surface in order to perform As(III) oxidation in water and that this TiO₂ immobilization, combined with coprecipitation of arsenic on Fe(III) hydroxides(oxides) could be an efficient way for inorganic arsenic removal from groundwaters.     

Distribution of pesticides and heavy metals in trophic chain

Determination of triazines herbicides (atrazine and simazine) by high performance liquid chromatography (HPLC) in samples of trophic chain were worked out. Determination limits of 0.5 μg g⁻¹ for atrazine, 0.8 μg g⁻¹ for simazine with pesticides recovery of 70–77% in trophic chain samples were obtained. The content of simazine in soils was in range 1.72–57.89 μg g⁻¹, in grass 5–88 μg g⁻¹, in milk 2.32–15.29 μg g⁻¹, in cereals 10.98–387 μg g⁻¹, in eggs 30.14–59.48 μg g⁻¹, for fruits: 2.45–6.19 μg g⁻¹. The content of atrazine in soils was in range 0.69–19.59 μg g⁻¹, in grass 7.85–23.85 μg g⁻¹, in cereals 1.88–43.08 μg g⁻¹. Cadmium, lead and zinc were determined by inductively coupled plasma atomic emission spectrometry (ICP-AES) in the same samples as atrazine and simazine. Determination limits for cadmium 5 × 10⁻³ μg g⁻¹, for lead 1 × 10⁻² μg g⁻¹, and for zinc 0.2 × 10⁻³ μg g⁻¹, were obtained. The content of cadmium in soil was in range 0.13–5.89 μg g⁻¹, in grass 114–627.72 × 10⁻³ μg g⁻¹, in milk 8.88–61.88 × 10⁻³ μg g⁻¹, in cereals 0.20–0.31 μg g⁻¹, in eggs 0.11–0.15 μg g⁻¹, in fruits 0.23–0.59 μg g⁻¹. The content of lead in soils was in range 0.57–151.50 μg g⁻¹, in grass 0.16–136.57 μg g⁻¹, in milk 1.16–3.74 μg g⁻¹, in cereals 1.05–5.47 μg g⁻¹, in eggs 5.79–55.87 μg g⁻¹, in fruits 21.00–87.36 μg g⁻¹. Zinc content in soil was in range 9.15–424.5 μg g⁻¹, in grass 35.20–55.87 μg g⁻¹, in milk 20.00–34.38 μg g⁻¹, in cereals 14.94–28.78 μg g⁻¹, in eggs 15.67–32.01 μg g⁻¹, in fruits 14.94–18.88 μg g⁻¹.

Described below extraction and mineralization methods for particular trophic chains allowed to determine of atrazine, simazine, cadmium, lead and zinc with good repeatability and precision. Emphasis was focused on liquid–liquid extraction and solid-phase extraction of atrazine and simazine from analysed materials, as well as, on monitoring the content of herbicides and metals in soil and along trophic chain. Higher concentration of pesticides in samples from west region of Poland in comparison to that of east region is likely related to common applying them in Western Europe in relation to East Europe. The content of metals strongly depends on samples origin (industry area, vicinity of motorways).     

Direct measurement of denitrification activity in a Gulf coast freshwater marsh receiving diverted Mississippi River water

Wetland loss along the Louisiana Gulf coast and excessive nitrate loading into the Gulf of Mexico are interrelated environmental problems. Nitrate removal by soil denitrification activity was studied in a ponded freshwater marsh receiving diverted Mississippi River water for the purpose of reversing or slowing wetland loss. Labeled ¹⁵N-nitrate was applied at 3.8 g N m⁻² into four replicate study plots after removing above ground vegetation. Nitrogen gas (N₂) and nitrous oxide (N₂O) emissions from the plots were determined by isotope ratio mass spectrometry (IRMS). Nitrous oxide emissions were also compared with the results determined by gas chromatograph (GC). Results showed that it took 2 weeks to remove the added nitrate with N₂O emission occurring over a period of 4 d. The apparent denitrification dynamics were assumed to follow the Michaelis–Menten equation. The maximum denitrification rate and K_m value were determined as 12.6 mg N m ⁻² h⁻¹, and 6.5 mg N l⁻¹, respectively. Therefore the maximum capacity for nitrate removal by the marsh soil would be equivalent to 110 g N m⁻² yr⁻¹, with more than 30% of nitrogen gas evolved as N₂O. For typical nitrate concentrations in Mississippi River water of about 1 mg N l⁻¹, nitrate would be removed at a rate of 14.7 g N m⁻² yr⁻¹ with N₂O emission about 1.5%. A denitrification dynamic model showed that the efficiency of nitrate removal would largely depend on the water discharge rate into the ponded wetland. Higher discharge rate will result in less retention time for the water in the marsh where nitrate is denitrified.     

Determination and distribution characteristics of degradation products of nonylphenol polyethoxylates in the rivers of Taiwan

Concentrations of degradation products of nonylphenol polyethoxylates (NPEOs) were analyzed in river water samples in order to determine the distribution characteristic of these alkylphenolic compounds in 18 major rivers of Taiwan. The degradation products of NPEOs were detected in all river samples, with the dicarboxylates alkylphenolic degradation products (CAPEC) being detected most frequently and at the highest concentrations. Concentrations of NP and NP1EO in rivers ranged from n.d. to 5.1 μg l⁻¹ and n.d. to 0.5 μg l⁻¹, respectively. The total concentrations of shortened carboxylates (i.e., NP1EC + NP2EC + NP3EC) and dicarboxylates alkylphenolic degradation products (CAP1EC + CAP2EC) ranged from n.d. to 63.6 μg l⁻¹ and n.d. to 94.6 μg l⁻¹, respectively. Concentrations of NP2EC, NP3EC and all CAPEC residues were determined semi-quantitatively by comparing with the internal standard. Significantly higher concentrations of CAPEC residues were detected in the river waters as compared to those of NP, NP1EO and NPEC degradation products and the average proportions of these compounds in the samples of the rivers were as follows: NP + NP1EO was 5 ± 2.5%, total NPEC was 25 ± 12%, and total CAPEC was 70 ± 12%. The high concentration ratios of CAPEC/NPEC illustrate that aerobic biodegradation plays a main route in the fate of NPEO in the rivers of Taiwan.     

On the performance of Fe and Fe,F doped Ti-Pt/PbO2 electrodes in the electrooxidation of the Blue Reactive 19 dye in simulated textile wastewater

The electrochemical performance of pure Ti–Pt/β-PbO₂ electrodes, or doped with Fe and F (together or separately), in the oxidation of simulated wastewaters containing the Blue Reactive 19 dye (BR-19), using a filter-press reactor, was investigated and then compared with that of a boron-doped diamond electrode supported on a niobium substrate (Nb/BDD). The electrooxidation of the dye simulated wastewater (volume of 0.1 l, with a BR-19 initial concentration of 25 mg l⁻¹) was carried out under the following conditions: current density of 50 mA cm⁻², volume flow rate of 2.4 l h⁻¹, temperature of 25 °C and electrode area of 5 cm². The performances of the electrodes in the dye decolorization were quite similar, achieving 100% decolorization, and in some cases 90% decolorization was achieved by applying only ca. 0.3 A h l⁻¹ (8 min of electrolysis). The reduction of the simulated wastewater organic load, monitored by its total organic carbon content (TOC), was greater for the Ti–Pt/β-PbO₂–Fe,F electrode obtained from an electrodeposition bath containing 1 mM Fe³⁺ and 30 mM F⁻. In this case, after 2 h of electrolysis the obtained TOC reduction was 95%, while for the pure β-PbO₂ and the Nb/BDD electrodes the reductions were 84% and 82%, respectively.     

Evaluating the impacts of some environmentally relevant factors on the availability of bisphenol A with negligible-depletion SPME

The effect of some environmentally relevant factors including salinity, pH, and humic acids on the availability of bisphenol A (BPA) was evaluated by using the negligible-depletion solid-phase microextraction (nd-SPME) biomimetic method. With the variation of salinity (0–500 mM NaCl) and pH (5.0–8.5) of aqueous solutions, the partition coefficients of BPA between the nd-SPME fiber and the aqueous solution varied in the range of log D = 3.55–3.86, which indicates that the salinity and pH can influence the availability of BPA. By using Acros humic acid as model dissolved organic matter (DOM), it was also demonstrated that the environmental factors such as salinity and pH could affect the partitioning of BPA between DOM and aqueous solutions. The determined partition coefficients of BPA between dissolved organic carbon (DOC) and aqueous solutions were in the range of log D_DOC = 4.03–5.60 for Acros humic acid solutions with 1–50 mg l⁻¹ DOC. The influence of salinity and pH on log D_DOC was more significant at low concentration (0–5 mg l⁻¹) of DOC.     

Biotransformation and antioxidant response in Ceratophyllum demersum experimentally exposed to 1,2- and 1,4-dichlorobenzene

We report the effects of 1,2- and 1,4-dichlorobenzene (1,2-DCB and 1,4-DCB) on the aquatic macrophyte Ceratophyllum demersum. We evaluated the response of the antioxidant system through the assay of glutathione reductase (GR), guaiacol peroxidase (POD) and glutathione peroxidase (GPx). Additionally, the effect of DCBs on the detoxication system by measuring the activity of glutathione-S-transferase (GST) was evaluated.

C. demersum showed elevated GST activities when exposed to 10 and 20 mg l⁻¹ 1,2-DCB, and at 10 mg l⁻¹ for 1,4-DCB. These results show that glutathione conjugation take place at relatively high concentrations of both isomers. Significantly increased activities of POD were also detected in C. demersum exposed to concentrations above 5 mg l⁻¹ of the corresponding isomer.

The GR activity was enhanced in plants exposed to 1,2-DCB (5 mg l⁻¹) and 1,4-DCB (10 mg l⁻¹). GPx was also significantly increased in exposures to the corresponding isomer, each at a concentration of 10 mg l⁻¹. However, plants exposed to low doses of 1,4-DCB (1 mg l⁻¹) showed significantly decreased activities of both enzymes GR and GPx.

Consequently, it is clear that the exposure of the aquatic macrophyte C. demersum to DCBs is able to cause an activation of the antioxidant system, showing an isomer specific pattern, which suggests that the defence system of this plant is playing an important role in scavenging ROS, helping to protect the organism against adverse oxidative effects generated by the prooxidant action of the tested xenobiotics. Furthermore, increased GST activities give indirect evidence on the conjugation of either DCBs or the corresponding metabolites during phase II of detoxication, which supports the elimination process of toxic metabolites from cells of C. demersum.     

Biosorption of cadmium by Myriophyllum spicatum L. and Myriophyllum triphyllum orchard

The aim of this study was to characterize the biological treatment of heavy metal-contaminated water employing Myriophyllum species, namely M. spicatum L. and M. triphyllum. Both species were found to be capable of removing cadmium (Cd) from water; the latter significantly outperformed. Myriophyllum species were treated with 0, 2, 4, 6, 8, 16 mg l⁻¹ cadmium solutions for 24, 48, 72, 96 h, respectively. Cd uptake of both species was the lowest at 2 mg l⁻¹ and the highest at 16 mg l⁻¹. Concentration related cadmium stress on both species exhibit significant difference on pigment levels (8–16 mg l⁻¹). These findings contribute to the fact that submerged aquatic plants can be used for the removal of heavy metals.     

Accelerated seeded precipitation pre-treatment of municipal wastewater to reduce scaling

Membrane based treatment processes are very effective in removing salt from wastewater, but are hindered by calcium scale deposit formation. This study investigates the feasibility of removing calcium from treated sewage wastewater using accelerated seeded precipitation. The rate of calcium removal was measured during bench scale batch mode seeded precipitation experiments at pH 9.5 using various quantities of calcium carbonate as seed material. The results indicate that accelerated seeded precipitation may be a feasible option for the decrease of calcium in reverse osmosis concentrate streams during the desalination of treated sewage wastewater for irrigation purposes, promising decreased incidence of scaling and the option to control the sodium adsorption ratio and nutritional properties of the desalted water. It was found that accelerated seeded precipitation of calcium from treated sewage wastewater was largely ineffective if carried out without pre-treatment of the wastewater. Evidence was presented that suggests that phosphate may be a major interfering substance for the seeded precipitation of calcium from this type of wastewater. A pH adjustment to 9.5 followed by a 1-h equilibration period was found to be an effective pre-treatment for the removal of interferences. Calcium carbonate seed addition at 10 g l⁻¹ to wastewater that had been pre-treated in this way was found to result in calcium precipitation from supersaturated level at 60 mg l⁻¹ to saturated level at 5 mg l⁻¹. Approximately 90% reduction of the calcium level occurred 5 min after seed addition. A further 10% reduction was achieved 30 min after seed addition.     

Determination of 4-tert-octylphenol, 4-nonylphenol and bisphenol A in surface waters from the Haihe River in Tianjin by gas chromatography-mass spectrometry with selected ion monitoring

The estrogenic pollutants 4-tert-octylphenol (OP), 4-nonylphenol (NP) and bisphenol A (BPA) were determined in surface water samples from the Haihe River, Tianjin, China. The analytes were extracted and concentrated from 300 ml acidified water samples by liquid–liquid extractions using dichloromethane, derivatized with trifluoroacetic anhydride, and quantified by gas chromatography–mass spectrometry (GC–MS) with selected ion monitoring (SIM). Among the samples collected from 14 sampling sites, only one sample was found to have a relatively high concentration of BPA (8.30 μg l⁻¹) and NP (0.55 μg l⁻¹). The concentrations of OP, NP and BPA in the other samples were in the range of 18.0–20.2, 106–296 and 19.1–106 ng l⁻¹, respectively. Recoveries for OP, NP and BPA in the spiked water samples were all over 80%.     

Isoprene emission from tropical trees in Okinawa Island, Japan

This study surveyed isoprene emission from 42 indigenous and exotic tropical trees in subtropic Okinawa, Japan. Of the 42 trees studied, 4 emitted isoprene at a rate in excess of 20 μg g⁻¹ h⁻¹, and 28 showed the rates of 1–10 μg g⁻¹ h⁻¹. The remainder emitted less than 1 μg g⁻¹ h⁻¹. The majority of trees in this study may therefore fall within the lower emitting species. However, species in Moraceae that is indigenous in Okinawa emitted isoprene at relatively higher rates with an average of 14.2 μg g⁻¹ h⁻¹. The highest emission rate of 107.1 μg g⁻¹ h⁻¹ for Ficus virgata yielded the area basis rate of 47.4 nmol m⁻² s⁻¹, which is almost equivalent to the rate of high emitting species. Furthermore, a linear relationship between light intensity and isoprene emission was noted with Ficus virgata up to 1700 μmol m⁻² s⁻¹. These findings may show the potential importance of subtropical areas as sources of isoprene to the atmosphere.     

The use of physiological characteristics for comparison of organic compounds phytotoxicity

The influence of intact (FLT) and photomodified (phFLT) fluoranthene (0.05, 0.5 and 5 μmol l⁻¹) and herbicide Basagran (5, 20, 35 and 50 nmol l⁻¹) on the germination, growth of seedlings and photosynthetic processes in pea plants (Pisum sativum L., cv. Garde) was investigated. The germination was significantly inhibited already by the lowest concentration (0.05 μmol l⁻¹) of FLT and phFLT, while Basagran caused inhibition only in higher concentrations (35 and 50 nmol l⁻¹). The growth of roots was significantly inhibited by higher concentration 5 μmol l⁻¹ of both FLT and phFLT and the shoot of seedlings was significantly influenced only by photomodified form. The length of root and shoot was inhibited already by concentration 5 nmol l⁻¹ of Basagran. Organic compounds applied on chloroplasts suspension influenced primary photochemical processes of photosynthesis. In chlorophyll fluorescence parameters, the significant increase of F₀ values and the decrease of F_V/F_M and Φ_II values by application of FLT (0.5 and 5 μmol l⁻¹) and phFLT (0.05, 0.5 and 5 μmol l⁻¹) was recorded. The maximum capacity of PSII (F_V/F_M) was influenced by the highest (50 nmol l⁻¹) and the effective quantum yield of PSII (Φ_II) already by the lowest (5 nmol l⁻¹) concentration of Basagran. Hill reaction activity decreased and was significantly inhibited by higher concentration (0.5 and 5 μmol l⁻¹) of FLT and phFLT and already by the lowest concentration (5 nmol l⁻¹) of Basagran.     

Kinetic studies of adsorption of thiocyanate onto ZnCl2 activated carbon from coir pith, an agricultural solid waste

The adsorption of thiocyanate onto ZnCl₂ activated carbon developed from coir pith was investigated to assess the possible use of this adsorbent. The influence of various parameters such as agitation time, thiocyanate concentration, adsorbent dose, pH and temperature has been studied. Adsorption followed second-order rate kinetics. Two theoretical adsorption isotherms, namely, Langmuir and Freundlich were used to describe the experimental results. The Langmuir adsorption capacity (Q₀) was found to be 16.2 mg g⁻¹ of the adsorbent. The per cent adsorption was maximum in the pH range 3.0–7.0. pH effect and desorption studies showed that ion exchange and chemisorption mechanism are involved in the adsorption process. Thermodynamic parameters such as ΔG⁰, ΔH⁰ and ΔS⁰ for the adsorption were evaluated. The negative values of ΔH⁰ confirm the exothermic nature of adsorption. Effects of foreign ions on the adsorption of thiocyanate have been investigated. Removal of thiocyanate from ground water was also tested.     

Utilization and degradation of imazaquin by a naturally occurring isolate of Arthrobacter crystallopoietes

A species of bacteria that is capable of utilizing imazaquin as the sole carbon source was isolated from soil with repeated imazaquin applications, and was identified as Arthrobacter crystallopoietes (designated as strain “WWX-1”). This isolate degrades imazaquin as high as 200 μg ml⁻¹, and the estimated dissipation half-lives increased from 1.51 d for the treatment at 50 μg ml⁻¹ to 4.75 d for 200 μg ml⁻¹. Optimal growth of WWX-1 in mineral salt medium with 50 μg ml⁻¹ imazaquin was obtained at 35 °C and a pH of 5.0. Growth of WWX-1 was also observed in mineral salt medium with the addition of other imidazolinone herbicides such as imazethapyr and imazapyr, but not with different classes of herbicides such as metsulfuron-methyl. Two imazaquin metabolites were detected, and spectral analysis with HPLC–MS, ¹H NMR, and IR revealed one metabolite with a molecular weight (MW) of 199 as quinoline-2,3-dicarboxylic anhydride. We propose that A. crystallopoietes (WWX-1) could serve as an efficient biodegradation system for remediation of water and soils that are heavily contaminated with imazaquin or other structurally similar chemicals.