Characteristics of aerosols collected in central Taiwan during an Asian dust event in spring 2000

Aerosol samples for PM(2.5) and PM(2.5-10) were collected at four locations in central Taiwan from 26 to 31 March 2000, a period that experienced exceedingly high PM levels from 29 to 30 March due to the passage of an Asian dust storm. The samples were analyzed for mass, metallic elements, ions, and carbon. The purpose of this paper is to investigate the influence of the dust storm on the characteristics of local ambient particulate matter. The results indicate that the concentrations of the crustal elements Ca, Mg, Al, Fe and the sea salt species Na+ and Cl- in PM(2.5-10) during the dust episode exceed the mean concentrations in the non-dust period by factors of 3.1, 2.9, 2.6, 2.2, 2.3 and 2.1 respectively. Enrichment factors of Ca, Fe, and Mg in PM(2.5-10) during the dust event are close to unity, indicating that these elements are from soil. Reconstruction of aerosol compositions revealed that soil of coarse particulates elevated approximately 50% in the dust event. It is noted that during the dust event, the ratio of Mg/Al in PM(2.5-10) ranged from 0.21 to 0.25 while that of Ca/Al ranged from 0.6 to 0.9, levels more constant than those obtained in non-dust period.     

Characterization of PM2.5 aerosols dominated by local pollution and Asian dust observed at an urban site in Korea during aerosol characterization experiments (ACE)--Asia Project

Daily fine particulate matter (PM2.5) samples were collected at Gwangju, Korea, during the Aerosol Characterization Experiments (ACE)-Asia Project to determine the chemical properties of PM2.5 originating from local pollution and Asian dust (AD) storms. During the study period, two significant events occurred on April 10-13 and 24-25, 2001, and a minor event occurred on April 19, 2001. Based on air mass transport pathways identified by back-trajectory calculation, the PM2.5 dataset was classified into three types of aerosol populations: local pollution and two AD aerosol types. The two AD types were transported along different pathways. One originated from Gobi desert area in Mongolia, passing through Hunshandake desert in Northern Inner Mongolia, urban and polluted regions of China (AD1), and the other originated in sandy deserts located in the Northeast Inner Mongolia Plateau and then flowed southward through the Korean peninsula (AD2). During the AD2 event, a smoke plume that originated in North Korea was transported to our study site. Mass balance closures show that crustal materials were the most significant species during both AD events, contributing -48% to the PM2.5 mass; sulfate aerosols (19.1%) and organic matter (OM; 24.6%) were the second greatest contributors during the AD1 and AD2 periods, respectively, indicating that aerosol properties were dependent on the transport pathway. The sulfate concentration constituted only 6.4% (4.5 microg/m3) of the AD2 PM2.5 mass. OM was the major chemical species in the local pollution-dominated PM2.5 aerosols, accounting for 28.7% of the measured PM2.5 mass, followed by sulfate (21.4%), nitrate (15%), ammonium (12.8%), elemental carbon (8.9%), and crustal material (6.5%). Together with substantial enhancement of the crustal elements (Mg, Al, K, Ca, Sc, Ti, Mn, Fe, Sr, Zr, Ba, and Ce), higher concentrations of pollution elements (S, V, Ni, Zn, As, Cd, and Pb) were observed during AD1 and AD2 than during the local pollution period, indicating that, in addition to crustal material, the AD dust storms also had a significant influence on anthropogenic elements.     

Windblown dust contributes to high PM2.5 concentrations

The revised National Ambient Air Quality Standards for PM include fine particulate standards based upon mass measurements of PM2.5. It is possible in arid and semi-arid regions to observe significant coarse mode intrusion in the PM2.5 measurement. In this work, continuous PM10, PM2.5, and PM1.0 were measured during several windblown dust events in Spokane, WA. PM2.5 constituted approximately 30% of the PM10 during the dust event days, compared with approximately 48% on the non-dusty days preceding the dust events. Both PM10 and PM2.5 were enhanced during the dust events. However, PM1.0 was not enhanced during dust storms that originated within the state of Washington. During a dust storm that originated in Asia and impacted Spokane, PM1.0 was also enhanced, although the Asian dust reached Washington during a period of stagnation and poor dispersion, so that local sources were also contributing to high particulate levels. The "intermodal" region of PM, defined as particles ranging in aerodynamic size from 1.0 to 2.5 microns, was found to represent a significant fraction of PM2.5 (approximately 51%) during windblown dust events, compared with 28% during the non-dusty days before the dust events.     

Metallic characteristics of PM2.5 and PM2.5-10 for clustered Aeolian Dust Episodes occurred in an extensive fluvial basin during rainy season

Aeolian dust episodes (ADEs) have been an emergency disaster in the Kaoping River Valley during the rainy season (May-September), which can severely deteriorate ambient particulate air quality in the region surrounding the Kaoping River. Thus, this study aims to characterize the metallic fingerprint of Aeolian dust (AD) and investigate the effects of ADEs on ambient particulate air quality along the Kaoping River Valley. Four manual sampling sites adjacent to the riverside were selected to collect fine (PM2.5) and coarse (PM2.5–10) aerosol samples during and after the ADEs in the periods of six events. A total of 13 metallic elements were analyzed using an inductively coupled plasma-atomic emission spectrometer. With metallic elements analysis and nonparametric statistical methods of Wilcoxon rank-sum test and Kruskal-Wallis test, this study successfully derived the metallic indicators of ADEs. The mass ratios of crustal elements (Fe, Ca, or Al) to reference element (Cd) obtained during the ADEs were much higher than those obtained after the ADEs. High mass ratios of Fe/Cd, Ca/Cd, and Al/Cd in PM2.5-10 were observed on the influenced areas of ADEs. Among them, (Fe/Cd)2.5-10 was proven as the best indicator which can be applied to effectively validate the existence of ADEs and evaluate their influences on ambient air quality. Moreover, PM2.5 concentrations during the ADEs were 3-3.6 fold higher than those after the ADEs. PM2.5 should be a contributor to AD, even though the mass ratios of PM2.5/PM10 ranged from 0.05 to 0.20 during the ADEs. Our findings provide valuable information regarding the characteristics of the AD during the ADEs in the Kaoping River.

Implications: Indicators of (Fe/Cd)_2.5-10 are approximately applied to observe the effects of ADEs. Local governments could realize the mechanisms of S- and NW-type aeolian dust episodes (ADEs). They can cause deterioration in different ways for the regional air quality surrounding Kaoping River Valley. Residents who have been living in the influenced areas can take precautions to prevent damage from aeolian dust. Strategies for curbing ADEs must reduce the area of bare lands by artificial measures in the long period of the sunny days during the rainy season. Future research should examine physical conditions of topsoils and other chemical composition in aeolian dust.     

Concentrations of particulate matter emitted from large cattle feedlots in Kansas

Particulate matter (PM) emitted from cattle feedlots are thought to affect air quality in rural communities, yet little is known about factors controlling their emissions. The concentrations of PM (i.e., PM2.5, PM10, and total suspended particulates or TSP) upwind and downwind at two large cattle feedlots (KS1, KS2) in Kansas were measured with gravimetric samplers from May 2006 to October 2009 (at KS1) and from September 2007 to April 2008 (at KS2). The mean downwind and net (i.e., downwind - upwind) mass concentrations of PM2.5, PM10, and TSP varied seasonally, indicating the need for multiple-day, seasonal sampling. The downwind and net concentrations were closely related to the moisture content of the pen surface. The PM2.5/PM10 and PM2.5/TSP ratios at the downwind sampling location were also related to the moisture content of the pen surface, humidity, and temperature. Measurement of the particle size distribution downwind of the feedlot with a cascade impactor showed geometric mean diameter ranging from 7 to 18 microm, indicating that particles that were emitted from the feedlots were generally large in size.     

Source apportionment of ambient total suspended particulates and coarse particulate matter in urban areas of Jiaozuo, China

Approximately 750 total suspended particulates (TSPs) and coarse particulate matter (PM10) filter samples from six urban sites and a background site and >210 source samples were collected in Jiaozuo City during January 2002 to April 2003. They were analyzed for mass and abundances of 25 chemical components. Seven contributive sources were identified, and their contributions to ambient TSP/PM10 levels at the seven sites in three seasons (spring, summer, and winter days) and a "whole" year were estimated by a chemical mass balance (CMB) receptor model. The spatial TSP average was high in spring and winter days at a level of approximately 530 microg/m(3) and low in summer days at 456 microg/m(3); however, the spatial PMo0 average exhibited little variation at a level of approximately 325 microg/m(3), and PM10-to-TSP ratios ranged from 0.58 to 0.81, which suggested heavy particulate matter pollution existing in the urban areas. Apportionment results indicated that geological material was the largest contributor to ambient TSP/PM10 concentrations, followed by dust emissions from construction activities, coal combustion, secondary aerosols, vehicle movement, and other industrial sources. In addition, paved road dust and re-entrained dust were also apportioned to the seven source types and found soil, coal combustion, and construction dust to be the major contributors.     

Analysis of temporal and spatial dichotomous PM air samples in the El Paso-Cd. Juarez air quality basin.

This paper presents and discusses the results obtained from the gravimetric and chemical analyses of the 24-hr average dichotomous samples collected from five sites in the El Paso-Cd. Juarez air quality basin between August 1999 and March 2000. Gravimetric analysis was performed to determine the temporal and spatial variations of PM2.5 (particulate matter less than 2.5 microm in diameter) and PM25-10 (particulate matter less than 10 pm but greater than 2.5 microm in diameter) mass concentrations. The results indicate that approximately 25% of the PM10 (i.e., PM25 + PM25-10) concentration is composed of PM2.5. Concurrent measurements of hourly PM concentrations and wind speed showed strong diurnal patterns of the regional PM pollution. Results of X-ray fluorescence (XRF) elemental analyses were compared to similar but limited studies performed by the Texas Natural Resource Conservation Commission (TNRCC) in 1990 and 1997. Major elements from geologic sources-Al, Si, Ca, Na, K, Fe, and Ti-accounted for 35% of the total mass concentrations in the PM2.5-10 fraction, indicating that geologic sources in the area are the dominant PM sources. Levels of toxic trace elements, mainly considered as products of anthropogenic activities, have decreased significantly from those observed in 1990 and 1997.     

Fugitive dust emission source profiles and assessment of selected control strategies for particulate matter at gravel processing sites in Taiwan

Particles emitted from gravel processing sites are one contributor to worsening air quality in Taiwan. Major pollution sources at gravel processing sites include gravel and sand piles, unpaved roads, material crushers, and bare ground. This study analyzed fugitive dust emission characteristics at each pollution source using several types of particle samplers, including total suspended particulates (TSP), suspended particulate (PM10), fine suspended particulate (PM2.5), particulate sizer, and dust-fall collectors. Furthermore, silt content and moisture in the gravel were measured to develop particulate emission factors. The results showed that TSP (< 100 microm) concentrations at the boundary of gravel sites ranged from 280 to 1290 microg/m3, which clearly exceeds the Taiwan hourly air quality standard of 500 microg/m3. Moreover, PM10 concentrations, ranging from 135 to 550 microg/m3, were also above the daily air quality standard of 125 microg/m3 and approximately 1.2 and 1.5 times the PM2.5 concentrations, ranging from 105 to 470 microg/m3. The size distribution analysis reveals that mass mean diameter and geometric standard deviation ranged from 3.2 to 5.7 microm and from 2.82 to 5.51, respectively. In this study, spraying surfactant was the most effective control strategy to abate windblown dust from unpaved roads, having a control efficiency of approximately 93%, which is significantly higher than using paved road strategies with a control efficiency of approximately 45%. For paved roads, wet suppression provided the best dust control efficiencies ranging from 50 to 83%. Re-vegetation of disturbed ground had dust control efficiencies ranging from 48 to 64%.     

PM source identification at Sunland Park, New Mexico, using a simple heuristic meteorological and chemical analysis

The causes for evening low-wind PM10 and PM2.5 peaks at Sunland Park, NM, were investigated by using wind sector analysis and by assessing relationships between PM loadings and meteorological parameters through canonical ordination analysis. Both PM10 and PM2.5 concentrations during the evening hours accounted for approximately 50% of their respective 24-hr averages, and the PM10 was mainly composed of coarse material (PM10-2.5 amounted to 77% of PM10). A wind sector analysis based on data from three surface meteorological monitoring stations in the region narrowed the potential source region for PM10 and PM2.5 to an area within a few kilometers south of Sunland Park. Canonical ordination analysis confirmed that the peak frequently occurred under stable conditions with weak southerly winds. Chemical analyses of PM showed that elemental and organic carbon (EC and OC, respectively) dominate PM2.5 and inorganic elements dominate PM10-2.5. The combined data for EC/OC, geologic elements, and various trace elements indicate that under low wind and stable conditions, traffic-related PM emissions (motor vehicle exhausts and re-suspended road dust) from the south of the site are the most likely sources for the evening PM10 and PM2.5 peaks.     

The effects of Asian Dust on particulate matter fractionation in Seoul,Korea during spring 2001

The concentrations of three different fractions of particulate matter (PM) including PM2.5, PM10, and TSP were determined concurrently during March-May 2001. Measurements of three PM fractions were made at hourly intervals from four different observatory sites located within the city boundary of Seoul. On the basis of this study, we attempted to describe relationships between the occurrences of the Asian Dust (AD) event and its influences on the PM distribution characteristics. The results of our study demonstrated distinct differences between concentrations of PM fractions at AD and non-AD (NAD) periods. The increase of PM observed during the AD episode appeared to be dominated by the coarse, rather than fine, fraction of PM. In addition, it was found that TSP/PM10 ratios were almost constant, while the coarse/fine or TSP/PM2.5 ratios changed noticeably between AD and NAD periods. In most cases, differences in environmental conditions between AD and NAD periods were prominent and proven to be statistically significant. Moreover, the regression relationships between PM and N-oxides indicate that the source processes governing PM levels between the AD and NAD period can be different. The overall results of our analysis were hence helpful enough to distinguish competing processes in AD and NAD periods, while suggesting indirectly the possible control of different source processes on PM fractionation.     

Assessment of influential range and characteristics of fugitive dust in limestone extraction processes

Fugitive dust emission from limestone extraction areas is a significant pollution source. The cracking operation in limestone extraction areas easily causes high total suspended particulate (TSP) concentrations in the atmosphere, occasionally exceeding the 1-hr national emission standard of Taiwan (500 microg/m3). The concentration and size distribution were measured at different distances (0.05-15 km) in the extraction areas. The highest hourly concentrations of TSP, PM10 (suspended particulate matter [PM] smaller than 10 microm), and PM2.5 (suspended PM smaller than 2.5 microm) are 1111, 825, and 236 microg/m3, respectively, during the cracking process. Measurement results obtained from the Micro-Orifice Uniform Deposit Impactor indicated that the mass median aerodynamic diameter is approximately 0.7 microm, with the geometric standard deviation exceeding 7. In addition, the emission factors are 0.143 and 0.211 kg/t for both vertical well and stair extraction operations, respectively. Experimental results demonstrate that the corresponding TSP control efficiencies for spraying water, planting grass, setting short walls, paving gravel roads, and establishing vertical well transportation are approximately 55, 50, 44, 22, and 30%, respectively. Furthermore, the PM10 control efficiencies are approximately 45, 41, 54, 35, and 30%, respectively, whereas the PM2.5 control efficiencies are roughly 23, 31, 15, 11, and 10%, individually.     

The study of fine and coarse particles, and metallic elements for the daytime and night-time in a suburban area of central Taiwan, Taichung

Daily average concentrations of fine and coarse particulates, and TSP samples have been measured simultaneously at daytime and night-time periods by using Universal and PS-1 sampler in a suburban area of central Taiwan from June to August 1998. The samples were analyzed by atomic absorption spectrometry to determine the fine and coarse particulate concentrations of metallic elements (Ca, Fe, Mn, Pb, Cu, Zn and Cr). The concentration of PM2.5 and TSP showed a decreased trend for the daytime period. The fine particle concentrations were about two times as that of coarse particulate concentrations. The averaged fine particulate concentrations at daytime are higher than at night-time. Ca and Fe were mostly in the coarse particulate mode. The correlation coefficients were 0.63 and 0.69 for elements Ca and Fe in the coarse particle mode for day and night periods. Pb showed a similar distribution ratio with Mn for the fine to coarse particle ratios at both day and night period. Pb and Mn are highly correlated for the day (R = 0.78) and night period (R = 0.61) at particle size <2.5 microm. Cu and Zn were mainly in fine particles at both day and night period. Fe and Ca consist of the major parts of all the elements. Elemental Mn is the lowest among the rest of the heavy metals.     

Chemical speciation of PM2.5 and PM10 in south Phoenix, AZ, USA

Phoenix, AZ, experiences high particulate matter (PM) episodes, especially in the wintertime. The spatial variation of the PM concentrations and resulting differences in exposure is of particular concern. In this study, PM2.s (PM with aerodynamic diameter <2.5 microm) and PM10 (PM with aerodynamic diameter <10 microm) samples were collected simultaneously from the east and west sides of South Phoenix and at a control site in Tempe and analyzed for trace elements and bulk elemental and organic carbon. Measurements showed that although PM2.5 concentrations had similar trends in temporal scale across all sites, concentrations of PM10 did not. The difference in PM10 concentrations and fluctuation across the three sites suggest effects of a local soil source as evidenced by high concentrations of Al, Ca, and Fe in PM10. K and anthropogenic elements (e.g., Cu, Pb, and Zn) in PM2.5 samples on January 1 were strikingly high, suggesting the influence of New Year's fireworks. Concentrations of toxic elements (e.g., Pb) in the study presented here are not different from similar studies in other U.S. cities. Application of principal component analysis indicated two broad categories of emission sources--soil and combustion--together accounting for 80 and 90% of variance, respectively, in PM2.5 and PM10. The soil and combustion components explained approximately 60 and 30% of the variance in PM10, respectively, whereas combustion sources dominated PM2.5 (>50% variance). Many elements associated with anthropogenic sources were highly enriched, with enrichment factors in PM2.5 an order of magnitude higher than in PM10 relative to surface soil composition in the study area.     

Analysis of regional and temporal characteristics of PM10 during an Asian dust episode in Korea

This study analyzes the regional and temporal distributions of PM10 concentrations observed in major metropolitan cities in Korea before, during and after a recent Asian dust episode in 2002. There were spatial and temporal variations in PM10 concentrations among the mid-western, the southwestern, the southeastern, and the southern parts of Korea during this Asian dust period due to the different air mass movement time and the different wind directions and speeds of prevailing winds in each city or region. The origins of the three-day Asian dust episode were identified by an analysis of two-day backward isentropic air trajectories. The different origins for each day also significantly contributed to the spatial and temporal variations in PM10 concentrations. A significant relationship was found between PM10 concentrations on the day preceding the first peak day and the first peak day of the Asian dust period but only in the mid-western areas. The concentrations of PM10 just after the Asian dust episode were much higher than those just before. There was a significant increase in a coarse fraction, having soil origins, of particles during the Asian dust episode. Concentrations of Mn, Fe, Ni and Cr extracted from the total suspended particulate (TSP) samples collected in 7 cities during the Asian dust episode were much higher when compared with other days in 2001. However, the Asian dust did not consistently increase the concentrations of lead, cadmium and copper as they are influenced by local sources such as local traffic or industrial emissions.     

Retrospective prediction of intraurban spatiotemporal distribution of PM2.5 in Taipei

Numerous studies have shown that fine airborne particulate matter particles (PM2.5) are more dangerous to human health than coarse particles, e.g. PM10. The assessment of the impacts to human health or ecological effects by long-term PM2.5 exposure is often limited by lack of PM2.5 measurements. In Taipei, PM2.5 was not systematically observed until August, 2005. Taipei is the largest metropolitan area in Taiwan, where a variety of industrial and traffic emissions are continuously generated and distributed across space and time. PM-related data, i.e., PM10 and Total Suspended Particles (TSP) are independently systematically collected by different central and local government institutes. In this study, the retrospective prediction of spatiotemporal distribution of monthly PM2.5 over Taipei will be performed by using Bayesian Maximum Entropy method (BME) to integrate (a) the spatiotemporal dependence among PM measurements (i.e. PM10, TSP, and PM2.5), (b) the site-specific information of PM measurements which can be certain or uncertain information, and (c) empirical evidence about the PM2.5/PM10 and PM10/TSP ratios. The performance assessment of the retrospective prediction for the spatiotemporal distribution of PM2.5 was performed over space and time during 2003–2004 by comparing the posterior pdf of PM2.5 with the observations. Results show that the incorporation of PM10 and TSP observations by BME method can effectively improve the spatiotemporal PM2.5 estimation in the sense of lower mean and standard deviation of estimation errors. Moreover, the spatiotemporal retrospective prediction with PM2.5/PM10 and PM2.5/TSP ratios can provide good estimations of the range of PM2.5 levels over space and time during 2003–2004 in Taipei.     

The study of TSP, PM(2.5-10) and PM2.5 during Taiwan Chi-Chi Earthquake in the traffic site of central Taiwan, Taichung

Ambient particle concentration was taken on the traffic sampling site over the Chung-Chi Road over bridge (CCROB) in front of Hungkuang Institute of Technology (HKIT). The sampling time was from August 1999 to December 1999. During the sampling period, Taiwan's biggest earthquake in more than a century registered 7.3 on the Richter scale (Taiwan Chi-Chi Earthquake). Besides, there were more than 20,000 aftershocks that followed the Taiwan Chi-Chi Earthquake within three months. Thus, the PM2.5, PM(2.5-10) particle concentrations were also collected then and compared with total suspended particle (TSP) in this study. The average PM(2.5-10), PM2.5 and TSP concentrations are 24.6, 58.0 and 106 microg/m3, respectively, after the Taiwan Chi-Chi Earthquake. The average TSP concentrations before and after Taiwan Chi-Chi Earthquake were 70 and 127 microg/m3, respectively. It is clearly shown that the average concentration of TSP after Taiwan Chi-Chi Earthquake was about 1.8 times as that of TSP concentration before Taiwan Chi-Chi Earthquake in the traffic site of central Taiwan. And the ratios of PM2.5/PM(2.5-10), PM2.5/PM10 and PM2.5/TSP are 2.2%, 67.2%, 38.9%, respectively. The results also indicated about Chi-Chi fine particle concentration (PM25) and the TSP increases in the traffic site of central Taiwan after Taiwan Chi-Chi Earthquake.     

The chemical and strontium isotope composition of atmospheric aerosols over Japan: the contribution of long-range-transported Asian dust (Kosa)

Atmospheric aerosols have been collected at four sites around Japan during 2000. From systematically monitoring the major (Na, Mg, Al, K, Ca, and Fe) and trace (Rb and Sr) elements, along with the Sr isotope composition, we have tried to estimate the contribution of long-range-transported Asian dust (“Kosa”) to the atmospheric aerosols.The results are summarized as follows:(1) The concentration of each element in the aerosols increased during the “Kosa” period. The increase was particularly obvious in samples collected on 8 April 2000, when the “Kosa Phenomenon” was observed at all the sampling sites in Japan, 2 days after a very heavy dust storm had occurred in China.(2) The Rb–Sr isotopic diagram shows a two-component mixing relationship: one with a high ⁸⁷Sr/⁸⁶Sr ratio and a high ⁸⁷Rb/⁸⁶Sr ratio, and the other with a low ⁸⁷Sr/⁸⁶Sr ratio and a low ⁸⁷Rb/⁸⁶Sr ratio. There is a significant difference between that of the expected end member of the Asian dust and that of the reported Asian loess, which is thought to be the possible source of the components of the “Kosa”, although the lower component is consistent with the local component at Wako.(3) Plots of the ⁸⁷Sr/⁸⁶Sr ratio vs the Ca/Al and Sr/Al ratios support a two-component mixing suggested by the Rb–Sr systematics, and they indicate that the contributing continental soil components to the “Kosa” aerosols should be composed of the silicate fraction of Asian loess.(4) The discrepancy in the Rb–Sr systematics between the expected end member and the possible sources may be caused by the dissolution of the Ca-bearing minerals via long-range dust transport, or by a combination of source characteristics and grain size separation.     

Analysis of Temporal and Spatial Dichotomous PM Air Samples in the El Paso-Cd. Juarez Air Quality Basin

ABSTRACT

This paper presents and discusses the results obtained from the gravimetric and chemical analyses of the 24-hr average dichotomous samples collected from five sites in the El Paso-Cd. Juarez air quality basin between August 1999 and March 2000. Gravimetric analysis was performed to determine the temporal and spatial variations of PM_2.5 (particulate matter less than 2.5 um in diameter) and PM2.5-10 (particulate matter less than 10 μm but greater than 2.5 μm in diameter) mass concentrations. The results indicate that ~25% of the PM10 (i.e., PM2.5 + PM2.5-10) concentration is composed of PM2.5. Concurrent measurements of hourly PM concentrations and wind speed showed strong diurnal patterns of the regional PM pollution. Results of X-ray fluorescence (XRF) elemental analyses were compared to similar but limited studies performed by the Texas Natural Resource Conservation Commission (TNRCC) in 1990 and 1997. Major elements from geologic sources—Al, Si, Ca, Na, K, Fe, and Ti—accounted for 35% of the total mass concentrations in the PM2.5-10 fraction, indicating that geologic sources in the area are the dominant PM sources. Levels of toxic trace elements, mainly considered as products of anthropogenic activities, have decreased significantly from those observed in 1990 and 1997.     

Source profiles for industrial, mobile, and area sources in the Big Bend Regional Aerosol Visibility and Observational study

Representative PM2.5 and PM10 source emissions were sampled in Texas during the Big Bend Regional Aerosol Visibility and Observa (BRAVO) study. Chemical source profiles for elements, ions, and carbon fractions of 145 samples are reported for paved and unpaved road dust, soil dust, motor vehicle exhaust, vegetative burning, four coal-fired power stations, an oil refinery catalytic cracker, two cement kilns, and residential meat cooking. Several samples were taken from each emitter and source type, and these were averaged by source type, and in source subgroups based on commonality of chemical composition. The standard deviation represents the variability of the chemical mass fractions. BRAVO profiles differed in some respects from profiles measured elsewhere. High calcium abundances in geological dust, high selenium abundances in coal-fired power stations, and high antimony abundances in oil refinery catalytic cracker emissions were found. Abundances of eight thermally evolved carbon fractions [Atmos. Environ. 28 (15) (1994) 2493] differ among combustion sources, and a Monte Carlo simulation demonstrates that these differences are sufficient to differentiate among several carbon-emitters.     

Evaluating inter-continental transport of fine aerosols:(2) Global health impact

In this second of two companion papers, we quantify for the first time the global impact on premature mortality of the inter-continental transport of fine aerosols (including sulfate, black carbon, organic carbon, and mineral dust) using the global modeling results of (Liu et al., 2009). Our objective is to estimate the number of premature mortalities in each of ten selected continental regions resulting from fine aerosols transported from foreign regions in approximately year 2000. Our simulated annual mean population-weighted (P-W) concentrations of total PM2.5 (aerosols with diameter less than 2.5 μm) are highest in East Asia (EA, 30 μg m^?3) and lowest in Australia (3.6 μg m^?3). Dust is the dominant component of PM2.5 transported between continents. We estimate global annual premature mortalities (for adults age 30 and up) due to inter-continental transport of PM2.5 to be nearly 380 thousand (K) in 2000. Approximately half of these deaths occur in the Indian subcontinent (IN), mostly due to aerosols transported from Africa and the Middle East (ME). Approximately 90K deaths globally are associated with exposure to foreign (i.e., originating outside a receptor region) non-dust PM2.5. More than half of the premature mortalities associated with foreign non-dust aerosols are due to aerosols originating from Europe (20K), ME (18K) and EA (15K); and nearly 60% of the 90K deaths occur in EA (21K), IN (19K) and Southeast Asia (16K). The lower and higher bounds of our estimated 95% confidence interval (considering uncertainties from the concentration–response relationship and simulated aerosol concentrations) are 18% and 240% of the estimated deaths, respectively, and could be larger if additional uncertainties were quantified. We find that in 2000 nearly 6.6K premature deaths in North America (NA) were associated with foreign PM2.5 exposure (5.5K from dust PM2.5). NA is least impacted by foreign PM2.5 compared to receptors on the Eurasian continent. However, the number of premature mortalities associated with foreign aerosols in NA (mostly occurring in the U.S.) is comparable to the reduction in premature mortalities expected to result from tightening the U.S. 8-h O₃ standard from 0.08 ppmv to 0.075 ppmv. International efforts to reduce inter-continental transport of fine aerosol pollution would substantially benefit public health on the Eurasian continent and would also benefit public health in the United States.