Application of EMF emission measurement techniques to wireless communications systems for compliance with directive 2004/40/EC.

Europe is the only region in the world with common legislative acts regulating exposure to electromagnetic fields (EMF) for both the general public and workers. Council Recommendation 1999/519/EC deals with the limitation of exposure of the general public to EMF (0 Hz-300 GHz). Directive 2004/40/EC regulates the minimum health and safety requirements regarding the exposure of workers to the risks arising from EMF. This paper discusses the general application of existing standards and recommendations in measurement techniques for determining compliance of measured exposure limit values and action values with those defined in 2004/40/EC.     

Occupational exposure to base stations-compliance with EU directive 2004/40/EC.

The rapid growth of mobile communications has not only led to a rising number of mobile telephones. It has also made base stations essential for these services widespread on many roofs. However, not everyone is aware that working close to sources of high frequency electromagnetic fields (EMF), such as transmitter antennas for mobile phones, pagers and police, fire and other emergency services, can result in high EMF exposure. This paper deals with measurements and calculations of the compliance boundary for workers in one typical roof top base station setting according to EU Directive and other relevant EN standards.     

Electromagnetic fields in offices.

With the increased use of electric and electronic equipment in our offices, our daily exposure to electromagnetic fields has become increasingly complex due to the great variety of the frequency content of the fields. Today focus has shifted from monitors as the dominating sources of electromagnetic fields to other electronic equipment, cabling, nearby substations, power lines and stray currents in buildings. In the last 5 years wireless communication has become common in our offices. These devices use radio frequency waves to communicate and are therefore sources of radio frequency fields in our offices. To a certain degree, they all add to the complicated issue of the extensive field frequencies found in offices. The exposure of office workers is generally considered to be low and not in conflict with the existing guidelines, but if a precaution approach is applied there are a number of measures that can be taken to reduce the electromagnetic fields in offices in order to obtain a good electrical environment.     

Occupational Exposure to Base Stations—Compliance With EU Directive 2004/40/EC

The rapid growth of mobile communications has not only led to a rising number of mobile telephones. It has also made base stations essential for services widespread on many roofs. However, not everyone is aware that working close to sources of high frequency electromagnetic fields (EMF), such as transmitter antennas for mobile phones, pagers and police, fire and other emergency services, can result in high EMF exposure. This paper deals with measurements and calculations of the compliance boundary for workers in one typical roof top base station setting according to EU Directive and other relevant EN standards.     

On-board safety monitoring systems for driving: review, knowledge gaps, and framework

IntroductionFatal highway incidents remain the leading type of fatal work-related event, carrying tremendous personal, social, and economic costs. While employers with a fixed worksite can observe and interact directly with workers in an effort to promote safety and reduce risk, employers with workers who operate a motor vehicle as part of their job have fewer options. New technologies such as on-board safety monitoring systems offer the potential to further improve safety. These technologies allow vehicle owners to collect safety-specific information related to a driver's on-the-road behavior and performance. While many such devices are being developed and implemented in both commercial fleets and private vehicles, the scientific examination of these devices has lagged by comparison.MethodIn the current paper, we: (a) describe the general features and functionality of current generations of on-board monitoring devices and how they might impact various driver behaviors; (b) review the current state of scientific knowledge specific to on-board devices; (c) discuss knowledge gaps and potential areas for future research, borrowing from the related domain of computer-based electronic performance monitoring (EPM); and (d) propose a framework that can be used to explore some of the human-system interactions pertaining to monitoring systems.Impact on IndustryMotor vehicle crashes can carry tremendous costs for employers, in terms of injury, disability, and loss of potentially productive work years. New technologies can offer tremendous benefits in terms of promoting safer on-the-road behaviors.     

Occupational exposure to electric and magnetic fields during tasks at ground or floor level at 110 kV substations in Finland

The aim was to investigate occupational exposure to electric and magnetic fields during tasks at ground or floor level at 110?kV substations in Finland and to compare the measured values to Directive 2013/35/EU. Altogether, 347 electric field measurements and 100 magnetic field measurements were performed. The average value of all electric fields was 2.3?kV/m (maximum 6.4?kV/m) and that of magnetic fields was 5.8?µT (maximum 51.0?µT). It can be concluded that the electric and magnetic field exposure at ground or floor level is typically below the low action levels of Directive 2013/35/EU. The transposition of the directive will not create new needs to modify the work practice of the evaluated tasks, which can continue to be performed as before. However, for workers with medical implants, the exposure may be high enough to cause interference.     

发电与高压输变电工程的工频电磁场现状及防护

通过对典型发电与高压输变电工程工频电磁场的现场检测,阐明了发电与高压输变电工程的工频电磁场现状.在此基础上,根据科学界关于极低频电磁场对人体短期和长期效应研究的明确结论,介绍了发电与高压输变电工程的工频电磁场暴露对人体健康的影响.同时,从卫生安全的角度提出了防止和减少工频电磁场影响的综合防护措施,其中包括:慎重选址,合理设计,适当个体防护和必要的警示标识.另外,扼要地介绍了工频电磁场的有关卫生标准和测量方法.     

高频焊接场所电磁辐射屏蔽与防护研究

焊接过程产生的电磁场对操作人员健康的影响已得到日益广泛的关注,对高频的防护问题,已成为改善劳动条件、保护劳动力的重要课题.在研究焊接生产电磁辐射环境、劳动者健康与安全现状的基础上,通过试验分析了电磁辐射屏蔽效率及导致屏蔽效率差异的因素.通过对不同部门制定的安全限值的比较分析,提出高频焊机安全使用建议.对控制高频焊接场所电磁辐射,尽可能降低从业人员电磁暴露的影响具有重要意义.     

Needle stick and sharps injuries among health care workers in Gondar city, Ethiopia

Background

All employees in health care settings handling needles or other sharps are at risk for needle stick and sharps injuries (NSSIs). Health care workers in under developed countries are at greater risk of infection from blood borne pathogens because of the lack of safety devices and the high prevalence of these pathogens.

Objectives

The aim of this study was to assess the prevalence of NSSIs and associated factors among health care workers in government health institutions in Gondar city, Ethiopia.

Methods

Institution based cross sectional study was conducted from May-December, 2010. The study included 344 health care workers who were selected from the source population using simple random sampling technique. Data were collected through interviews using structured and pre-tested questionnaire and the collected data were entered and analyzed using SPSS version 16.0.

Results

The prevalence of NSSIs among health care workers in the preceding 12 months was 106 (30.8%), of which 58 (54.7%) was reported by females. Lack of training on occupational health and safety, working more than 48 h/week, dissatisfaction with work environment and work culture, greater than 10 years of work experience and having low and moderate perception of risk were found to be significantly associated with NSSIs.

Conclusion

The study found high prevalence of NSSIs among health care workers. Effective training, ongoing awareness on the risk of hazards, preventive measures such as engineering control, and post-exposure prophylaxis following NSSIs are essential to reduce the risk of such injuries.     

Nanotechnologies,engineered nanomaterials and occupational health and safety – A review

The significance of engineered nanomaterials (ENM) and nanotechnologies grows rapidly. Nanotechnology applications may have a positive marked impact on many aspects of on human every day life, for example by providing means for the production of clean energy and pure drinking water. Hundreds of consumer nano-based products are already on the market. However, very little is known of the risks of ENM to occupational safety and health (OSH), even though workers are likely to be at extra risk, as compared with other potentially exposed groups of people, because the levels of exposure are usually higher at workplaces than in other environments. However, knowledge of the exposure to, or effects of, ENM on human health and safety in occupational environments is limited and does not allow reliable assessment of risks of ENM on workers’ health. Several issues related to ENM in the workplaces require marked attention. The most topical issues include: (1) improved understanding of ENM metrics associated with ENM toxicity; (2) development of monitoring devices for ENM exposure assessment; (3) understanding the changes of ENM structure and state of agglomeration at different concentrations in aerosols; (4) understanding translocation of ENM in the human body; (5) identifying the key health effects of ENM including pulmonary toxicity, genotoxicity, carcinogenic effects, and effects on circulation; (6) development of tiered approaches for testing of safety of ENM; and (7) utilizing these data for health risk assessment, with a special emphasis on occupational environment. Available data on several ENM – ability to enter the body and reach almost any organ, to cause pulmonary inflammation and fibrosis, and even to cause increased risk of mesotheliomas in animal models, call for immediate action. It is crucial to identify those ENM that may cause occupational health and safety risks from those ENM which are innocent, hence allowing prioritization of regulatory and preventive actions at workplaces at national, regional and global levels.     

An examination of beliefs about older workers: Do stereotypes still exist?

This study examined individuals' beliefs about older workers. Of particular interest was the relationship between those beliefs and individuals' (a) interactions with older workers, (b) supervisory status, and (c) demographic variables. Findings indicated that although older workers hold more positive beliefs about older workers than younger workers hold, even younger workers tended to have generally positive beliefs. Chronological age was found to moderate two relationships. First, the number of younger workers' interactions with older workers significantly, positively affected younger workers' beliefs about older workers. Second, an examination of the interaction between supervisory status and age found that older supervisors hold more negative beliefs about older workers than younger supervisors.     

Health Risk Assessment of Occupational Exposure to a Magnetic Field From Magnetic Resonance Imaging Devices

Health care staff who operate magnetic resonance imaging (MRI) devices are exposed to a static magnetic field of significant spatial heterogenity always produced by MRI magnets during the whole shift. They can also be exposed to pulses of a time-varying magnetic field (gradient field) present only during patients’ examinations. The level of the workers’ exposure depends both on the type of the magnet and on the ergonomic design of each MRI device.

The paper presents methods used for measuring and assessing workers’ exposure. It also discusses the results of inspection measurements carried out next to approximately 20 MRI devices of approximately 0.2–2.0 T. The presented characteristic and overview of the variability of workers’ exposure to a variety of MRI devices supports the need for data on monitoring occupational exposure to MRI. International exposure assessment standards and guidelines (International Commission on Non-Ionizing Radiation Protection [ICNIRP], Institute of Electrical and Electronics Engineers [IEEE], American Conference of Governmental and Industrial Hygienists [ACGIH], European Commission directive), and those established in Poland are also compared.     

Occupational noise exposure and hearing defects among sawmill workers in the south of Thailand

The aim of this study was to investigate occupational noise exposure and hearing defects among sawmill workers in the south of Thailand. Seven hundred sawmill workers participated, of which 335 (47.9%) were male. The mean age of the sawmill workers was 33.5 years (SD 10.2), and more than 60% were <35 years old; 75.1% of the workers had less than 5 years of work experience. Only about one in four workers (25%) had been trained in use of personal protective equipment (PPE), and half of the participants never or rarely wore PPE while working. The prevalence rate of noise-induced hearing loss (NIHL) was 22.8% (N?=?42). Male workers had significantly higher risk than female workers (odds ratio [OR]?=?2.21). Workers aged older than 25 years had significantly higher risks for NIHL (OR?=?3.51–12.42) than workers younger than 25 years. Sawing workers had higher risk for NIHL than office workers (OR?=?3.07).     

Quantification of risk perception: Development and validation of the construction worker risk perception (CoWoRP) scale

Introduction: The construction sector is leading in the number of accidents and fatalities; risk perception is the key to driving these numbers. Previous construction safety studies on risk perception quantification have not considered affective risk perception of construction workers or conducted comprehensive reliability and validity testing. Thus, this study aims to fill this need by developing a psychometrically sound instrument – the Construction Worker Risk Perception (CoWoRP) Scale – to assess the risk perception of construction workers. Method: Four phases of scale development, namely, item development, factor analysis, reliability assessment, and validity assessment were conducted with the collection and testing of data from a group (n = 469) of voluntary construction workers in Hong Kong. Results: The CoWoRP Scale with 13 items was shown to have acceptable test–retest reliability, internal consistency reliability, as well as content, convergent, discriminant, and criterion-related validity. Also, the CoWoRP Scale was affirmed to have three dimensions of worker risk perception, namely risk perception – probability, risk perception – severity, risk perception – worry and unsafe. These three dimensions of worker risk perception were negatively correlated with their risk-taking behavior. Conclusions: The CoWoRP Scale is a reliable and valid instrument for measuring the risk perception of construction workers and is expected to facilitate the construction safety studies that take risk perception of construction workers into account. Practical applications: The CoWoRP Scale could serve as an aptitude test to identify the characteristics of construction workers most likely to perceive lower risk in risky work situations. In turn, this information could help safety management provide safety training programs to those workers to enhance their risk perception and thereby minimizing their risk-taking behavior, reducing unnecessary training costs, and improving the construction safety performance.     

Assessing disabling and non-disabling injuries and illnesses using accepted workers compensation claims data to prioritize industries of high risk for Oregon young workers

Introduction: Young workers are especially vulnerable to occupational injuries and illnesses. There is a continued need to investigate injury burden among young workers across demographics and industry to inform targeted interventions. Workers compensation (WC) claims are important for quantifying work-related injuries and illnesses, however published studies have focused on disabling claims. This study extended previous research on Oregon young workers by including the most recent WC claims data to identify patterns of injury and high risk industries. Methods: We obtained all accepted disabling claims (N = 13,360) and a significant portion of non-disabling claims (N = 24,660) on workers aged 24 years and under from 2013 to 2018. Claim count, rate and cost were calculated by year, age, gender, industry, and injury type. A prevention index (PI) method was used to rank industries in order to inform prevention efforts. Results: Average annual disabling and non-disabling claim rates were 111.6 and 401.3 per 10,000 young workers. Workers aged 19–21 (disabling: 119.0 per 10,000 and non-disabling: 429.3) and 22–24 years (115.7 and 396.4) and male workers (145.3 and 509.0) had higher claim rates than workers aged 14–18 (80.6 and 297.0) and female workers (79.8 and 282.9). The most frequent injury types were “struck by/against” (35.6%) and “work-related musculoskeletal disorders (WMSDs)” (19.5%). High risk industries included agriculture, construction, and manufacturing for both genders combined. For female young workers, the highest risk industry was healthcare. Conclusions: This study demonstrated the added value of non-disabling WC claims data. Using both disabling and non-disabling data and PI method, agriculture, construction, manufacturing and healthcare industries were identified as priority workplaces to prevent common and costly injuries among Oregon young workers. Practical Applications: While the industries identified are considered hazardous for all workers, findings in this study can guide targeted research and prevention efforts specific to young workers.     

Protection of workers’ mental health in Québec: Do general duty clauses allow labour inspectors to do their job?

Given that no specific provisions of the Occupational Health and Safety (OHS) Act explicitly deal with psychosocial risk factors, in Québec, occupational health and safety inspectors employed by the Commission de la santé et de la sécurité du travail (CSST) address psychosocial hazards under the Act’s general duty clause. This general duty clause and related provisions require that all employers eliminate hazards at source and protect the health of workers. More specifically, they are required to ensure that the organisation of work does not adversely affect the safety or health of the worker. Since 2004, Québec minimum standards legislation has also provided for the right of workers to an environment that is free from psychological harassment.Written from both a legal and public health perspective, this paper has two primary objectives: first, to better understand the potential and limits of the current legislative framework for the protection of the mental health of workers and second, to describe how scientific knowledge related to high risk situations for the mental health of workers might inform interventions by inspectors for the protection of workers’ mental health.     

The use and risk of portable electronic devices while cycling among different age groups

Introduction: In the Netherlands, a survey was set up to monitor the extent of the use of portable, electronic devices while cycling amongst different age groups of cyclists and to estimate the possible consequences for safety. Method: The main research questions concerned age differences in the self-reported use of electronic devices while cycling, self-reported crash involvement and risk, and self-reported compensatory behaviour. Teen cyclists (12–17 years) and young adult cyclists (18–34 years) were more frequent users, and also more indiscriminate users of portable devices while cycling than middle-aged and older adult cyclists (35–49 years; 50 + years). Results: After statistical correction for influences on crash risk of urbanization level, weekly time spent cycling, and cycling in more demanding traffic situations, the odds of being involved in a bicycle crash were estimated to be higher for teen cyclists and young adult cyclists who used electronic devices on every trip compared to same age groups cyclists who never used these devices. For middle-aged and older adult cyclists, the use of portable electronic devices was not a significant predictor of bicycle crashes, but frequency of cycling in demanding traffic situations was. Possible implications for education or legal measures are discussed. Impact on Industry: Results may inform researchers, policy makers, and cyclists themselves. Educational campaigns may use risk information to warn young cyclists about risk of device use while cycling.     

煤矿井下电磁环境测试方法研究

为了分析煤矿井下电磁环境对矿用电子设备工作安全性的影响,研究井下电磁辐射现场测试方法。测试结果表明:煤矿井下电磁环境具有区域性,典型设备是其电磁特性的主要影响因素。架线电机车产生的电磁噪声覆盖的频段较宽,对井底车场电磁环境影响很大。矿用漏泄通信系统对井下电磁环境会产生一定的影响,变压器是井下变电所电磁环境的主要骚扰源。研究结果表明井下电磁环境现场测试方法具有一定的适用性,有助于确定井下电磁环境的严酷等级,为电子设备的抗干扰措施提供理论依据。     

高频感应焊接场所电磁曝露的研究

分析了MOSFET(Metal-Oxide-Semiconductor Field-Effect Transistor)管固态电源高频焊机在工作过程中产生电磁场的机理,通过定性分析和实际测量描述了不同工作条件下的高频时变电场特征,与ICNIRP发布的限定值比较,分析了焊接作业人员的高频电磁曝露问题。通过对高频焊接环境电磁辐射的定量描述和认识,对于规范焊接操作,尽可能降低从业人员电磁曝露的影响具有指导意义。