Prediction of some in situ tracer tests with sorbing tracers using independent data

Some recent converging tracer tests with sorbing tracers at the Asp? Hard Rock Laboratory in Sweden, the TRUE tests, have been predicted using only laboratory data and hydraulic data from borehole measurements. No model parameters were adjusted to obtain a better fit with the experiments. The independent data were fracture frequency and transmissivity data obtained in the field and laboratory data on sorption and matrix diffusion. Transmissivity measurements in five boreholes in the rock volume containing the region surrounding the injection and collection points show that there is a high frequency of water conducting fractures. Of 162 packed off sections with 0.5 m packer distances, 112 were found to have a transmissivity above the detection limit. The specific flow-wetted surface (FWS) of the rock mass could be estimated from these data. The transmissivities were found to be reasonably well described by a lognormal distribution. Laboratory data on diffusion and sorption properties together with the hydraulic data were used to "predict" the residence time distribution (RTD) of the sorbing tracers. The results were compared with the experimental breakthrough curves. In these experiments, the water residence time is very small compared to the residence time of the sorbing tracers due to their diffusion and sorption within the rock matrix. We thus could neglect the influence of the water residence time in our predictions. Therefore, no information on water residence times or on "dispersion" was needed. The dispersion of the sorbing tracers is caused by the different sorbing tracer residence times in different pathways. The sorbing tracer residence time is determined by the ratio of flowrate to the flow-wetted surface in the different pathways and not by the water residence time. Assuming a three-dimensional flow pattern and using the observed fracture frequency and flowrate distribution, breakthrough curves for three strongly sorbing tracers were predicted. Only the laboratory data, the transmissivity measurements and the pumping flowrate were used in the predictions. No information on the water residence time as obtained by the nonsorbing tracers was used. The predictions were surprisingly accurate.     

Tracer test at El Berrocal site

Tracer tests provide highly valuable information about the transport properties of saturated rocks which is essential to the characterization of a potential radioactive waste repository site. In the frame of El Berrocal project, a set of tracer tests was performed in a complex geometry of inclined boreholes, combined with highly fractured transmissive zones. The aims of the tracer test programme were to gain experience, knowledge and insight into field transport experiments. To achieve this a detailed programme of new instrumentation design, site characterization and laboratory tasks was developed. For field monitoring a new electronic system was developed. The system is able to measure up to 256 parameters per borehole, with surface equipment to control pumping rates and physical and chemical parameters at both injection and extraction boreholes. The experiments progressed from single borehole dilution tests under both natural flow and forced gradient conditions to convergent flow tracer tests. Dilution tests helped to discriminate the most suitable borehole sections at which to inject tracers. The tracers were selected by the results of the laboratory programme. Uranine (fluorescein), DTPA-gadolinium (diethylenetriaminopentacetic acid, gadolinium (III)), and deuterium were injected simultaneously in one borehole section and recovered at another borehole 20 m away, pumping at a flowrate of 0.1 1 min⁻¹. First results showed a thickness porosity of 1.2 × 10⁻³ m and a longitudinal dispersivity of 17.0 m using uranine data acquired over a period of 4 d, at which point the recovery concentration had reached a maximum. However, gadolinium and deuterium appeared to travel faster, arriving at peak values after only 2 d of injection.     

Interpretation of injection-withdrawal tracer experiments conducted between two wells in a large single fracture

Tracer experiments conducted using a flow field established by injecting water into one borehole and withdrawing water from another are often used to establish connections and investigate dispersion in fractured rock. As a result of uncertainty in the uniqueness of existing models used for interpretation, this method has not been widely used to investigate more general transport processes including matrix diffusion or advective solute exchange between mobile and immobile zones of fluid. To explore the utility of the injection-withdrawal method as a general investigative tool and with the intent to resolve the transport processes in a discrete fracture, two tracer experiments were conducted using the injection-withdrawal configuration. The experiments were conducted in a fracture which has a large aperture (>500 microm) and horizontally pervades a dolostone formation. One experiment was conducted in the direction of the hydraulic gradient and the other in the direction opposite to the natural gradient. Two tracers having significantly different values of the free-water diffusion coefficient were used. To interpret the experiments, a hybrid numerical-analytical model was developed which accounts for the arcuate shape of the flow field, advection-dispersion in the fracture, diffusion into the matrix adjacent to the fracture, and the presence of natural flow in the fracture. The model was verified by comparison to a fully analytical solution and to a well-known finite-element model. Interpretation of the tracer experiments showed that when only one tracer, advection-dispersion, and matrix diffusion are considered, non-unique results were obtained. However, by using multiple tracers and by accounting for the presence of natural flow in the fracture, unique interpretations were obtained in which a single value of matrix porosity was estimated from the results of both experiments. The estimate of porosity agrees well with independent measurements of porosity obtained from core samples. This suggests that: (i) the injection-withdrawal method is a viable tool for the investigation of general transport processes provided all relevant experimental conditions are considered and multiple conservative tracers are used; and (ii) for the conditions of the experiments conducted in this study, the dominant mechanism for exchange of solute between the fracture and surrounding medium is matrix diffusion.     

Modelling of nonreactive tracer dipole tests in a shear zone at the Grimsel test site

The investigation of the migration of a high pH plume in a fractured shear zone is foreseen by a long-term experiment at the Grimsel rock laboratory. In order to characterise the initial conditions for the long-term experiment and to evaluate an optimal hydraulic in situ set-up, several dipole experiments with nonreacting tracers have been performed. The dipole experiments differ in geometry, pumping rates and orientation to the background water flow. Several single and double-porosity models have been applied to fit the results of these dipole tracer tests in order to extract values for some transport parameters and discriminate for certain transport processes. A two-dimensional porous medium approach was successfully used to fit tracer breakthrough curves measured for a dipole experiment. A model based on a one-dimensional dual porous medium approach was also successful, although the applied hydraulic dipole, with similar injection and extraction rates, suggests the existence of an extended two-dimensional flow field. For the two-dimensional porous medium approach, tracer breakthrough could only be fitted with a complex flow field geometry within the heterogeneous fractured shear zone. The heterogeneity was generated by heterogeneous porosity and hydraulic permeability distributions. Predictions for further dipole geometries and a sorbing tracer have been calculated by means of both models using the flow and transport parameters deduced from fits for a single dipole experiment. This allows for comparison with the measured breakthrough of sorbing tracers. The foreseen experiment with sorbing (radionuclide) tracers will help decide on the appropriate approach that should be used to describe such dipole experiments in this shear zone. Additionally, the migration and spreading of a solution with high pH has been calculated taking into account mineral dissolution and precipitation in a two-dimensional porous medium approach in order to estimate the amount and character of the mineral reactions induced by the interaction between the high pH solution and the rock.     

Modeling tracer diffusion in fractured and unfractured, unsaturated, porous media

A proposed tracer diffusion test for the Exploratory Shaft Facility at Yucca Mountain, NV, is modeled. For the proposed test, a solution containing conservative tracers will be introduced into a borehole in the geologic medium of interest. The tracers will diffuse and advect from the saturated source region into the unsaturated matrix in the surrounding tuff. After some time, the borehole is to be overcored, and tracer concentrations in the fluid will be measured in the core as a function of distance from emplacement. The data will be used to evaluate diffusive behavior and to derive effective diffusion coefficients for the tracers in the specific tuff. Numerical simulations are used to study the effects of effective diffusion coefficient, porosity, saturation, and fracturing on tracer transport. Results are reported for numerical simulations of tests in the Topopah Spring Member and the Tuff of Calico Hills, which have significantly different porosities and saturations. The simulations make the following predictions: The spread of tracer during the test will be sensitive to the effective diffusion coefficient of the tracer. Tracer will diffuse farther in the Topopah Spring Member than in the Tuff of Calico Hills because of the former's lower porosity and saturation. Tracer transport by advection into the Topopah Spring Member will be greater than that into the Tuff of Calico Hills because of capillary effects. While advection will be a significant mechanism for tracer penetration into the Topopah Spring tuff, it will be less significant for tracer penetration into the Calico Hills tuff. The proximity of a single vertical fracture to the source region determines its effects on tracer transport, especially if the fracture diverts fluid flowing from the source region into the matrix.     

Modelling the migration of contaminants through variably saturated dual-porosity, dual-permeability chalk

In the Hesbaye region in Belgium, tracer tests performed in variably saturated fissured chalk rocks presented very contrasting results in terms of transit times, according to artificially controlled water recharge conditions prevailing during the experiments. Under intense recharge conditions, tracers migrated across the partially or fully saturated fissure network, at high velocity in accordance with the high hydraulic conductivity and low effective porosity (fracture porosity). At the same time, a portion of the tracer was temporarily retarded in the almost immobile water located in the matrix. Under natural infiltration conditions, the fissure network remained inactive. Tracers migrated downward through the matrix, at low velocity in relation with the low hydraulic conductivity and the large porosity of the matrix. Based on these observations, Brouyère et al. (2004a) [Brouyère, S., Dassargues, A., Hallet, V., 2004a. Migration of contaminants through the unsaturated zone overlying the Hesbaye chalky aquifer in Belgium: a field investigation, J. Contam. Hydrol., 72 (1-4), 135-164, doi: 10.1016/j.conhyd.2003.10.009] proposed a conceptual model in order to explain the migration of solutes in variably saturated, dual-porosity, dual-permeability chalk. Here, mathematical and numerical modelling of tracer and contaminant migration in variably saturated fissured chalk is presented, considering the aforementioned conceptual model. A new mathematical formulation is proposed to represent the unsaturated properties of the fissured chalk in a more dynamic and appropriate way. At the same time, the rock water content is partitioned between mobile and immobile water phases, as a function of the water saturation of the chalk rock. The groundwater flow and contaminant transport in the variably saturated chalk is solved using the control volume finite element method. Modelling the field tracer experiments performed in the variably saturated chalk shows the adequacy and usefulness of the new conceptual, mathematical and numerical model.     

Field investigation into unsaturated flow and transport in a fault: model analyses

Results of a fault test performed in the unsaturated zone of Yucca Mountain, Nevada, were analyzed using a three-dimensional numerical model. The fault was explicitly represented as a discrete feature and the surrounding rock was treated as a dual-continuum (fracture-matrix) system. Model calibration against seepage and water-travel-velocity data suggests that lithophysal cavities connected to fractures can considerably enhance the effective fracture porosity and therefore retard water flow in fractures. Comparisons between simulation results and tracer concentration data also indicate that matrix diffusion is an important mechanism for solute transport in unsaturated fractured rock. We found that an increased fault-matrix and fracture-matrix interface areas were needed to match the observed tracer data, which is consistent with previous studies. The study results suggest that the current site-scale model for the unsaturated zone of Yucca Mountain may underestimate radionuclide transport time within the unsaturated zone, because an increased fracture-matrix interface area and the increased effective fracture porosity arising from lithophysal cavities are not considered in the current site-scale model.     

A multi-directional tracer test in the fractured Chalk aquifer of E. Yorkshire, UK

A multi-borehole radial tracer test has been conducted in the confined Chalk aquifer of E. Yorkshire, UK. Three different tracer dyes were injected into three injection boreholes and a central borehole, 25 m from the injection boreholes, was pumped at 330 m(3)/d for 8 days. The breakthrough curves show that initial breakthrough and peak times were fairly similar for all dyes but that recoveries varied markedly from 9 to 57%. The breakthrough curves show a steep rise to a peak and long tail, typical of dual porosity aquifers. The breakthrough curves were simulated using a 1D dual porosity model. Model input parameters were constrained to acceptable ranges determined from estimations of matrix porosity and diffusion coefficient, fracture spacing, initial breakthrough times and bulk transmissivity of the aquifer. The model gave equivalent hydraulic apertures for fractures in the range 363-384 microm, dispersivities of 1 to 5 m and matrix block sizes of 6 to 9 cm. Modelling suggests that matrix block size is the primary controlling parameter for solute transport in the aquifer, particularly for recovery. The observed breakthrough curves suggest results from single injection-borehole tracer tests in the Chalk may give initial breakthrough and peak times reasonably representative of the aquifer but that recovery is highly variable and sensitive to injection and abstraction borehole location. Consideration of aquifer heterogeneity suggests that high recoveries may be indicative of a high flow pathway adjacent, but not necessarily connected, to the injection and abstraction boreholes whereas low recoveries may indicate more distributed flow through many fractures of similar aperture.     

Solute transport in crystalline rocks at Äspö — I: Geological basis and model calibration

Water-conducting faults and fractures were studied in the granite-hosted Äspö Hard Rock Laboratory (SE Sweden). On a scale of decametres and larger, steeply dipping faults dominate and contain a variety of different fault rocks (mylonites, cataclasites, fault gouges). On a smaller scale, somewhat less regular fracture patterns were found. Conceptual models of the fault and fracture geometries and of the properties of rock types adjacent to fractures were derived and used as input for the modelling of in situ dipole tracer tests that were conducted in the framework of the Tracer Retention Understanding Experiment (TRUE-1) on a scale of metres. After the identification of all relevant transport and retardation processes, blind predictions of the breakthroughs of conservative to moderately sorbing tracers were calculated and then compared with the experimental data. This paper provides the geological basis and model calibration, while the predictive and inverse modelling work is the topic of the companion paper [J. Contam. Hydrol. 61 (2003) 175].The TRUE-1 experimental volume is highly fractured and contains the same types of fault rocks and alterations as on the decametric scale. The experimental flow field was modelled on the basis of a 2D-streamtube formalism with an underlying homogeneous and isotropic transmissivity field. Tracer transport was modelled using the dual porosity medium approach, which is linked to the flow model by the flow porosity. Given the substantial pumping rates in the extraction borehole, the transport domain has a maximum width of a few centimetres only. It is concluded that both the uncertainty with regard to the length of individual fractures and the detailed geometry of the network along the flowpath between injection and extraction boreholes are not critical because flow is largely one-dimensional, whether through a single fracture or a network. Process identification and model calibration were based on a single uranine breakthrough (test PDT3), which clearly showed that matrix diffusion had to be included in the model even over the short experimental time scales, evidenced by a characteristic shape of the trailing edge of the breakthrough curve. Using the geological information and therefore considering limited matrix diffusion into a thin fault gouge horizon resulted in a good fit to the experiment. On the other hand, fresh granite was found not to interact noticeably with the tracers over the time scales of the experiments.While fracture-filling gouge materials are very efficient in retarding tracers over short periods of time (hours–days), their volume is very small and, with time progressing, retardation will be dominated by altered wall rock and, finally, by fresh granite. In such rocks, both porosity (and therefore the effective diffusion coefficient) and sorption K_ds are more than one order of magnitude smaller compared to fault gouge, thus indicating that long-term retardation is expected to occur but to be less pronounced.     

Controlled release,blind tests of DNAPL characterization using partitioning tracers

The partitioning tracer technique for dense nonaqueous phase liquid (DNAPL) characterization was evaluated in an isolated test cell, in which controlled releases of perchloroethylene (PCE) had occurred. Four partitioning tracer tests were conducted, two using an inverted, double five-spot pumping pattern, and two using vertical circulation wells. Two of the four tests were conducted prior to remedial activities, and two were conducted after. Each test was conducted as a "blind test" where researchers conducting the partitioning tracer tests had no knowledge of the volume, method of release, nor resulting spatial distribution of DNAPL. Multiple partitioning tracers were used in each test, and the DNAPL volume estimates varied significantly within each test based on the different partitioning tracers. The tracers with large partitioning coefficients generally predicted a smaller volume of PCE than that expected based on the actual release volume. However, these predictions were made for low DNAPL saturations (average saturation was approximately 0.003), under conditions near the limits of the method's application. Furthermore, there were several factors that may have hindered prediction accuracy, including tracer degradation and remedial fluid interference.     

A stochastic multi-channel model for solute transport--analysis of tracer tests in fractured rock

Some of the basic assumptions of the advection-dispersion model (AD-model) are revisited. This model assumes a continuous mixing along the flowpath similar to Fickian diffusion. This implies that there is a constant dispersion length irrespective of observation distance. This is contrary to most field observations. The properties of an alternative model based on the assumption that individual water packages can retain their identity over long distances are investigated. The latter model is called the multi-channel model (MCh-model). Inherent in the latter model is that if the waters in the different pathways are collected and mixed, the "dispersion length" is proportional to distance. The conditions for when non-mixing between adjacent streams can be assumed are explored. The MCh- and AD-models are found to have very similar residence time distributions (RTD) for Peclet numbers larger than 3. A generalized relation between flowrate and residence time is developed, including the so-called cubic law and constant aperture assumptions. The two models extrapolate very differently when there is strong matrix interaction. The AD-model could severely underestimate the effluent concentration of a tracer pulse and overestimate the residence time. The conditions are explored for when in-filling particles in the fracture will not be equilibrated but will act as if there was seemingly a much larger flow wetted surface (FWS). It is found that for strongly sorbing tracers, relatively small particles can act in this way for systems and conditions that are typical of many tracer tests. The assumption that the tracer residence time found by cautiously injecting a small stream of traced water represents the residence time in the whole fracture is explored. It is found that the traced stream can potentially sample a much larger fraction of the fracture than the ratio between the traced flowrate and the total pumped flowrate. The MCh-model was used to simulate some recent tracer tests in what is assumed to be a single fracture at the Asp? Hard rock laboratory in Sweden. Non-sorbing tracers, HTO and Uranin were used to determine the mean residence time and its variance. Laboratory data on diffusion and sorption properties were used to "predict" the RTD of the sorbing tracers. At least 30 times larger FWS or 1000 times larger diffusion or sorption coefficients would be needed to explain the observed BTCs. Some possible reasons for such behavior are also explored.     

Modeling field-scale multiple tracer injection at a low-level waste disposal site in fractured rocks: effect of multiscale heterogeneity and source term uncertainty on conceptual understanding of mass transfer processes

Multiple factors may affect the scale-up of laboratory multi-tracer injection into structured porous media to the field. Under transient flow conditions and with multiscale heterogeneities in the field, previous attempts to scale-up laboratory experiments have not answered definitely the questions about the governing mechanisms and the spatial extent of the influence of small-scale mass transfer processes such as matrix diffusion. The objective of this research is to investigate the effects of multiscale heterogeneity, mechanistic and site model conceptualization, and source term density effect on elucidating and interpreting tracer movement in the field. Tracer release and monitoring information previously obtained in a field campaign of multiple, conservative tracer injection under natural hydraulic gradients at a low-level waste disposal site in eastern Tennessee, United States, is used for the research. A suite of two-pore-domain, or fracture-matrix, groundwater flow and transport models are calibrated and used to conduct model parameter and prediction uncertainty analyses. These efforts are facilitated by a novel nested Latin-hypercube sampling technique. Our results verify, at field scale, a multiple-pore-domain, multiscale mechanistic conceptual model that was used previously to interpret only laboratory observations. The results also suggest that, integrated over the entire field site, mass flux rates attributable to small-scale mass transfer are comparable to that of field-scale solute transport. The uncertainty analyses show that fracture spacing is the most important model parameter and model prediction uncertainty is relatively higher at the interface between the preferred flow path and its parent bedrock. The comparisons of site conceptual models indicate that the effect of matrix diffusion may be confined to the immediate neighborhood of the preferential flow path. Finally, because the relatively large amount of tracer needed for field studies, it is likely that source term density effect may exaggerate or obscure the effect of matrix diffusion on the movement of tracers from the preferred flow path into the bedrock.     

Analysis of colloid and tracer breakthrough curves

We consider the dispersion and elution of colloids and dissolved nonsorbing tracers within saturated heterogeneous porous media. Since flow path geometry in natural systems is often ill-characterized macroscopic (mean) flow rates and dispersion tensors are utilized in order to account for the sub-model scale microscopic fluctuations in media structure (and the consequent hydrodynamic profile). Even for tracer migration and dispersal this issue is far from settled.Here we consider how colloid and tracer migration phenomena can be treated consistently. Theoretical calculations for model flow geometries yield two quantitative predictions for the transport of free (not yet captured) colloids with reference to a non-sorbing dissolved tracer within the same medium: the average migration velocity of the free colloids is higher than that of the tracer; and that the ratio of the equivalent hydrodynamic dispersion rates of colloids and tracer is dependent only upon properties of the colloids and the porous medium, it is independent of pathlengths and fluid flux, once length scales are large enough.The first of these is well known, since even in simple flow paths free colloids must stay more centre stream. The second, if validated suggests how solute and colloid dispersion may be dealt with consistently in macroscopic migration models. This is crucial since dispersion is usually ill-characterized and unaddressed by the experimental literature. In this paper we present evidence based upon an existing Drigg field injection test for the validity of these predictions.We show that starting from experimental data the fitted dispersion rates of both colloids and non-sorbing tracers increase with the measured elution rates (obeying slightly different rules for tracers and colloids); and that the ratio of colloid and nonsorbing tracer elution rates, and the ratio of colloid and nonsorbing tracer dispersion rates may be dependent upon properties of the colloids and the medium (not the flow regime).It is important to realize that even for unretarded species, an earlier peak in the breakthrough curve does not necessarily correspond to a faster mean elution rate, or vice versa. But rather that a colloid may elute faster but disperse less than an equivalent tracer. Hence its peak may be retarded compared to that of the tracer, even assuming no retardation. Hence one must consider a combination of mean elution rate and mean dispersion rate, and not rely on “peak times” to corroborate chromatographic effects. The importance of this lies in the fact that these processes are not independent and yet upscale differently. Thus realistic estimates of effective colloid dispersion rates should be upscaled in a way consistent with that adopted for tracers within the same system.     

In situ tracer tests to determine retention properties of a block scale fracture network in granitic rock at the Aspö Hard Rock Laboratory, Sweden

Experiments were conducted at the Asp? Hard Rock Laboratory in order to improve the understanding of radionuclide retention properties of fractured crystalline bedrock in the 10-100 m scale (TRUE Block Scale Project, jointly funded by ANDRA, ENRESA, Nirex, JNC, Posiva and SKB). A series of tracer experiments were performed using sorbing tracers in three different flow paths. The different flow paths had Euclidian lengths of 14, 17 and 33 m, respectively, and one to three water conducting structures. Four tests were performed using different cocktails made up of radioactive sorbing tracers (22,24Na+, 42K+, 47Ca2+, 85Sr2+, 83,86Rb+, 131,133Ba2+ and 134,137Cs+). For each tracer injection, the breakthrough of sorbing tracers was compared to the breakthrough of a conservative tracer, 82Br-, 131I-, HTO and 186ReO4-, respectively. In the two longer flow paths, no breakthrough of 83Rb+ and 137Cs+ was observed after 8 months of pumping. Selected tracer tests were subject to basic modelling in which a one-dimensional (1D) advection-dispersion model, including surface sorption, and an unlimited matrix diffusion were used for the interpretation of the results. The results of the modelling indicated that there is a slightly higher mass transfer into a highly porous material in the block-scale experiment compared with in situ experiments performed over shorter distances and significantly higher than what would have been expected from laboratory data obtained from studies of the interactions in nonaltered intact rock.     

Field-scale colloid migration experiments in a granite fracture

An understanding of particle migration in fractured rock, required to assess the potential for colloid-facilitated transport of radionuclides, can best be evaluated when the results of laboratory experiments are demonstrated in the field. Field-scale migration experiments with silica colloids were carried out at AECL's Underground Research Laboratory (URL), located in southern Manitoba, to develop the methodology for large-scale migration experiments and to determine whether colloid transport is possible over distances up to 17 m. In addition, these experiments were designed to evaluate the effects of flow rate and flow path geometry, and to determine whether colloid tracers could be used to provide additional information on subsurface transport to that provided by conservative tracers alone. The colloid migration studies were carried out as part of AECL's Transport Properties in Highly Fractured Rock Experiment, the objective of which was to develop and demonstrate methods for evaluating the solute transport characteristics of zones of highly fractured rock. The experiments were carried out within fracture zone 2 as two-well recirculating, two-well non-recirculating, and convergent flow tests, using injection rates of 5 and 10 1 min⁻¹. Silica colloids with a 20 nm size were used because they are potentially mobile due to their stability, small size and negative surface charge. The shapes of elution profiles for colloids and conservative tracers were similar, demonstrating that colloids can migrate over distances of 17 m. The local region of drawdown towards the URL shaft affected colloid migration and, to a lesser extent, conservative tracer migration within the flow field established by the two-well tracer tests. These results indicate that stable colloids, with sizes as small as 20 nm, have different migration properties from dissolved conservative tracers. - 1997 Atomic Energy of Canada.     

Solute transport in crystalline rocks at Aspö--I: geological basis and model calibration

Water-conducting faults and fractures were studied in the granite-hosted Asp? Hard Rock Laboratory (SE Sweden). On a scale of decametres and larger, steeply dipping faults dominate and contain a variety of different fault rocks (mylonites, cataclasites, fault gouges). On a smaller scale, somewhat less regular fracture patterns were found. Conceptual models of the fault and fracture geometries and of the properties of rock types adjacent to fractures were derived and used as input for the modelling of in situ dipole tracer tests that were conducted in the framework of the Tracer Retention Understanding Experiment (TRUE-1) on a scale of metres. After the identification of all relevant transport and retardation processes, blind predictions of the breakthroughs of conservative to moderately sorbing tracers were calculated and then compared with the experimental data. This paper provides the geological basis and model calibration, while the predictive and inverse modelling work is the topic of the companion paper [J. Contam. Hydrol. 61 (2003) 175]. The TRUE-1 experimental volume is highly fractured and contains the same types of fault rocks and alterations as on the decametric scale. The experimental flow field was modelled on the basis of a 2D-streamtube formalism with an underlying homogeneous and isotropic transmissivity field. Tracer transport was modelled using the dual porosity medium approach, which is linked to the flow model by the flow porosity. Given the substantial pumping rates in the extraction borehole, the transport domain has a maximum width of a few centimetres only. It is concluded that both the uncertainty with regard to the length of individual fractures and the detailed geometry of the network along the flowpath between injection and extraction boreholes are not critical because flow is largely one-dimensional, whether through a single fracture or a network. Process identification and model calibration were based on a single uranine breakthrough (test PDT3), which clearly showed that matrix diffusion had to be included in the model even over the short experimental time scales, evidenced by a characteristic shape of the trailing edge of the breakthrough curve. Using the geological information and therefore considering limited matrix diffusion into a thin fault gouge horizon resulted in a good fit to the experiment. On the other hand, fresh granite was found not to interact noticeably with the tracers over the time scales of the experiments. While fracture-filling gouge materials are very efficient in retarding tracers over short periods of time (hours-days), their volume is very small and, with time progressing, retardation will be dominated by altered wall rock and, finally, by fresh granite. In such rocks, both porosity (and therefore the effective diffusion coefficient) and sorption K(d)s are more than one order of magnitude smaller compared to fault gouge, thus indicating that long-term retardation is expected to occur but to be less pronounced.     

Tracer diffusion from a horizontal fracture into the surrounding matrix: measurement by computed tomography

The vertical diffusion of NaI solution from a horizontal fracture into and within the surrounding matrix was tracked and quantified over time using an artificially fractured chalk core (30x5 cm) and a second-generation X-ray computed tomography (CT) scanner. The different tracer-penetration distances imaged in the matrix above and below the horizontal fracture are indicative of a greater tracer mass penetrating into the lower matrix. The enhanced transport in the matrix below the fracture was related to the Rayleigh-Darcy instability induced by the density differences between the heavier tracer solution in the fracture (1.038) and the distilled water that had initially resided in the matrix. Our observations suggest that below the fracture, the tracer is propagated by an advection-diffusion process that is characterized by both higher rates and higher concentrations relative to its propagation by diffusion above the fracture. The experimental results suggest that the prediction of contaminant migration in a rock intersected by both vertical and horizontal (e.g. along bedding planes) fractures is difficult because of density effects that result in different solute-penetration rates.     

Mass removal of chlorinated ethenes from rough-walled fractures using permanganate

In situ chemical oxidation (ISCO) employing permanganate is an emerging technology that has been successful at enhancing mass removal from DNAPL source zones in unconsolidated media at the pilot-scale. The focus of this study was to evaluate the applicability of flushing a permanganate solution across two single vertical fractures in a laboratory environment to remove free phase DNAPL. The fracture experiments were designed to represent a portion of a larger fractured aquifer system impacted by a near-surface DNAPL spill over a shallow fractured rock aquifer. Each fracture was characterized by hydraulic and tracer tests, and the aperture field for one of the fractures was mapped using a co-ordinate measurement machine. Following DNAPL emplacement, a series of water and permanganate flushes were performed. To support observations from the fracture experiments, a set of batch experiments was conducted. The data from both fracture experiments showed that the post-oxidation effluent concentration was not impacted by the oxidant flush; however, changes in the aperture distribution, flow field, and flow rate were observed. These changes resulted in a significant decrease to the mass loading from the fractures, and were attributed to the build-up of oxidation by-products (manganese oxides and carbon dioxide) within the fracture which was corroborated by the batch experiment data and visual examination of the walls of one fracture. These results provide insight into the potential impact that a permanganate solution and oxidation by-products can have on the aperture distribution within a fracture and on DNAPL mass transfer rates. A permanganate flush or injection completed within a fractured rock aquifer may lead to the development of an insoluble product adjacent to the DNAPL which results in the reduction or complete elimination of advective regions near the DNAPL and reduces mass transfer rates. This outcome would have significant implications on the plume generating potential of the remaining DNAPL.     

Incorporating layer- and local-scale heterogeneities in numerical simulation of unsaturated flow and tracer transport

This study characterizes layer- and local-scale heterogeneities in hydraulic parameters (i.e., matrix permeability and porosity) and investigates the relative effect of layer- and local-scale heterogeneities on the uncertainty assessment of unsaturated flow and tracer transport in the unsaturated zone of Yucca Mountain, USA. The layer-scale heterogeneity is specific to hydrogeologic layers with layerwise properties, while the local-scale heterogeneity refers to the spatial variation of hydraulic properties within a layer. A Monte Carlo method is used to estimate mean, variance, and 5th, and 95th percentiles for the quantities of interest (e.g., matrix saturation and normalized cumulative mass arrival). Model simulations of unsaturated flow are evaluated by comparing the simulated and observed matrix saturations. Local-scale heterogeneity is examined by comparing the results of this study with those of the previous study that only considers layer-scale heterogeneity. We find that local-scale heterogeneity significantly increases predictive uncertainty in the percolation fluxes and tracer plumes, whereas the mean predictions are only slightly affected by the local-scale heterogeneity. The mean travel time of the conservative and reactive tracers to the water table in the early stage increases significantly due to the local-scale heterogeneity, while the influence of local-scale heterogeneity on travel time gradually decreases over time. Layer-scale heterogeneity is more important than local-scale heterogeneity for simulating overall tracer travel time, suggesting that it would be more cost-effective to reduce the layer-scale parameter uncertainty in order to reduce predictive uncertainty in tracer transport.     

Influence of hydrological and geochemical processes on the transport of chelated metals and chromate in fractured shale bedrock

Field-scale processes governing the transport of chelated radionuclides in groundwater remain conceptually unclear for highly structured, heterogeneous environments. The objectives of this research were to provide an improved understanding and predictive capability of the hydrological and geochemical mechanisms that control the transport behavior of chelated radionuclides and metals in anoxic subsurface environments that are complicated by fracture flow and matrix diffusion. Our approach involved a long-term, steady-state natural gradient field experiment where nonreactive Br- and reactive 57Co(II)EDTA2- 109CdEDTA2-, and 51Cr(VI) were injected into a fracture zone of a contaminated fractured shale bedrock. The spatial and temporal distribution of the tracer and solutes was monitored for 500 days using an array of groundwater sampling wells instrumented within the fast-flowing fracture regime and a slower flowing matrix regime. The tracers were preferentially transported along strike-parallel fractures coupled with the slow diffusion of significant tracer mass into the bedrock matrix. The chelated radionuclides and metals were significantly retarded by the solid phase with the mechanisms of retardation largely due to redox reactions and sorption coupled with mineral-induced chelate-radionuclide dissociation. The formation of significant Fe(III)EDTA byproduct that accompanied the dissociation of the radionuclide-chelate complexes was believed to be the result of surface interactions with biotite which was the only Fe(III)-bearing mineral phase present in these Fe-reducing environments. These results counter current conceptual models that suggest chelated contaminants move conservatively through Fe-reducing environments since they are devoid of Fe-oxyhydroxides that are known to aggressively compete for chelates in oxic regimes. Modeling results further demonstrated that chelate-radionuclide dissociation reactions were most prevalent along fractures where accelerated weathering processes are expected to expose more primary minerals than the surrounding rock matrix. The findings of this study suggest that physical retardation mechanisms (i.e. diffusion) are dominant within the matrix regime, whereas geochemical retardation mechanisms are dominant within the fracture regime.