Priority assessment of toxic substances in life cycle assessment. Part II: assessing parameter uncertainty and human variability in the calculation of toxicity potentials

Toxicity potentials are standard values used in life cycle assessment (LCA) to enable a comparison of toxic impacts between substances. This paper presents the results of an uncertainty assessment of toxicity potentials that were calculated with the global nested multi-media fate, exposure and effects model USES-LCA. The variance in toxicity potentials resulting from input parameter uncertainties and human variability was quantified by means of Monte Carlo analysis with Latin Hypercube sampling (LHS). For Atrazine, 2,3,7,8-TCDD and Lead, variation, expressed by the ratio of the 97.5%-ile and the 2.5%-ile, ranges from about 1.5 to 6 orders of magnitude. The major part of this variation originates from a limited set of substance-specific input parameters, i.e. parameters that describe transport mechanisms, substance degradation, indirect exposure routes and no-effect concentrations. Considerable correlations were found between the toxicity potentials of one substance, in particular within one impact category. The uncertainties and correlations reported in the present study may have a significant impact on the outcome of LCA case studies.     

Human population intake fractions and environmental fate factors of toxic pollutants in life cycle impact assessment

The present paper outlines an update of the fate and exposure part of the fate, exposure and effects model USES-LCA. The new fate and exposure module of USES-LCA was applied to calculate human population intake fractions and fate factors of the freshwater, marine and terrestrial environment for 3393 substances, including neutral organics, dissociating organics and inorganics, emitted to 7 different emission compartments. The human population intake fraction is on average 10(-5)-10(-8) for organics and 10(-3)-10(-4) for inorganics, depending on the emission compartment considered. Chemical-specific human population intake fractions can be 1-2.7 orders of magnitude higher or lower compared to the typical estimates. For inorganics, the human population intake fractions highly depend on the assumption that exposure via food products can be modelled with constant bioconcentration factors. The environmental fate factor is on average 10(-11)-10(-18) days m(-3) for organics and 10(-10)-10(-12) days m(-3) for inorganics, depending on the receiving environment and the emission compartment considered. Chemical-specific environmental fate factors can be 1-8 orders of magnitude higher or lower compared to the typical estimates. The largest differences between the new and old version of USES-LCA are found for emissions to air and soil. This is caused by a significant change in the structure of the air and soil compartments in the new version of USES-LCA, i.e. the distinction between rural and urban air, including rain-no rain conditions and including soil depth dependent intermedia transport.     

Substituent effects on azo dye oxidation by the FeIII-EDTA-H2O2 system

Toxicity potentials are scaling factors used in life cycle assessment (LCA) indicating their relative importance in terms of potential toxic impacts. This paper presents the results of an uncertainty assessment of toxicity potentials for 181 substances that were calculated with the global nested multi-media fate, exposure and effects model USES-LCA. The variance in toxicity potentials resulting from choices in the modelling procedure was quantified by means of scenario analysis. A first scenario analysis showed to what extent potential impacts in the relatively short term are obscured by the inclusion of impacts on the very long term. Toxicity potentials representing potential impacts over time horizons of 20, 100 and 500 years were compared with toxicity potentials representing potential impacts over an infinite time horizon. Time horizon dependent differences up to 6.5 orders of magnitude were found for metal toxicity potentials, while for toxicity potentials of organic substances under study, differences remain within 0.5 orders of magnitude. The second scenario analysis addressed to what extent potential impacts on the continental scale are obscured by the inclusion of impacts on the global scale. Exclusion of potential impacts on the global scale changed the toxicity potentials of metals and volatile persistent halogenated organics up to 2.3 orders of magnitude. These scenario analyses also provide the basis for determining exports to future generations and outside the emission area.     

An environmental fate, exposure and risk assessment of ethylene oxide from diffuse emissions

Ethylene oxide (EO) is mainly used as a chemical intermediate and as a fumigant and sterilizing agent. Through its manufacturing and intended uses, EO may be released into the environment. Therefore, an assessment of the environmental significance of those potential emissions was conducted. Data were collected describing pertinent physical properties, degradation and other loss mechanisms that control the fate of EO in the environment. Available aquatic and terrestrial ecotoxicity data were assembled and used as the basis of calculating critical toxicity values to characterize hazard. Environmental compartment concentrations of EO were calculated using Level III fugacity-based modeling. Six scenarios were developed to account for different climatic conditions in various portions of the US. Finally, potential regional-scale risks to aquatic and terrestrial wildlife were determined. In the conceptual model that was developed in this assessment, EO diffuses into air, partitions between environmental compartments, is transported out of the different compartments via advection, and undergoes abiotic and biological degradation within each compartment. All known emissions within the continental USA were assumed to enter a modeled region roughly the size of the State of Ohio. Organisms (receptors) were assumed to dwell in both terrestrial and aquatic compartments. Receptors were assumed to include small mammals, soil invertebrates, water column (pelagic) organisms, and sediment benthos. The goal of this assessment was to characterize any potential adverse risks to terrestrial and aquatic wildlife populations. Hazard Quotients (HQ) were calculated by dividing predicted concentrations of EO in air, water, sediment, and soil by their critical toxicity values. Maximum calculated HQ values in air were 1.52x10(-7), in water were 1.17x10(-5), in sediment were 2.25x10(-4), and in soil were 1.37x10(-5). The results of this assessment suggest that EO as currently manufactured and used does not pose adverse risks to aquatic or terrestrial wildlife. In all cases, the HQ values were much less than the maximum desired HQ value of 1.0 (4,400-6,600,000 times), indicating that the potential for diffuse emissions of EO to pose adverse environmental risks is quite low.     

Geographical scenario uncertainty in generic fate and exposure factors of toxic pollutants for life-cycle impact assessment

In environmental life-cycle assessments (LCA), fate and exposure factors account for the general fate and exposure properties of chemicals under generic environmental conditions by means of 'evaluative' multi-media fate and exposure box models. To assess the effect of using different generic environmental conditions, fate and exposure factors of chemicals emitted under typical conditions of (1).Western Europe, (2). Australia and (3). the United States of America were compared with the multi-media fate and exposure box model USES-LCA. Comparing the results of the three evaluative environments, it was found that the uncertainty in fate and exposure factors for ecosystems and humans due to choice of an evaluative environment, as represented by the ratio of the 97.5th and 50th percentile, is between a factor 2 and 10. Particularly, fate and exposure factors of emissions causing effects in fresh water ecosystems and effects on human health have relatively high uncertainty. This uncertainty is mainly caused by the continental difference in the average soil erosion rate, the dimensions of the fresh water and agricultural soil compartment, and the fraction of drinking water coming from ground water.     

An examination of the physical properties,fate, ecotoxicity and potential environmental risks for a series of propylene glycol ethers

Propylene glycol ethers (PGEs) are comprised of mono-, di- and tri-PGEs and several of their acetate esters. The nature of the range of applications that use PGEs suggests that there is a potential for both intentional and unintentional entry of the materials into the environment. Selected physical/chemical properties, fate characteristics, aquatic toxicity data and calculated environmental concentrations were used to assess potential risks from the manufacture, handling, use, and disposal of PGEs. In general, the PGEs are low to moderately volatile, have high aqueous solubilities, low octanol-water partition coefficients (Kow), and bioconcentration factor values of <10, which indicate they are unlikely to accumulate in aquatic food chains. Both abiotic and biological degradation processes reduce environmental concentrations of PGEs. In air, vapor-phase PGEs react with photo-chemically produced hydroxyl radicals and have half-lives ranging from 5.5 to 34.4 h. A variety of ready and inherent biodegradation test methods, as well as tests that simulate biodegradation in wastewater treatment plants, surface water and soil have been conducted on PGEs. Significant aerobic biodegradation was generally observed, with a range of biodegradation half-lives on the order of 5-25 d. Acute aquatic toxicity studies with PGEs resulted in LC50 values ranging from approximately >100 to >20,000 mg/l for freshwater fish, the pelagic invertebrate Daphnia magna, green algae Selenastrum capricornutum (now called Pseudokirchneriella capricornutum) and bacteria. Level 3 multi-media modeling (EQC model of Mackay) was used to simulate regional-scale concentrations of PGEs in air, soil, water, and sediment. Toxicity thresholds were then compared with regional-scale water, soil and sediment concentrations to determine hazard quotients. Based upon this analysis, concentrations of PGEs are unlikely to pose adverse risks to the environment.     

Terrestrial and aquatic ecotoxicity assessment of Cr(VI) by the ReCiPe method calculation (LCIA): application on an old industrial contaminated site

The most stable forms of chromium in the environment are chromium (III) and chromium (VI), the former being relatively immobile and necessary for organisms, and the latter being highly soluble and toxic. It is thus important to characterise ecotoxicological impacts of Cr(VI). However, there are still some important uncertainties in the calculation of ecotoxicological impacts of heavy metals in the LCIA global approach. The aim of this paper is to understand how the spatial and dynamic characterization of life cycle inventory (LCI) data can be exploited in life cycle impact assessment and particularly for the evaluation of the aquatic and terrestrial ecotoxicity of Cr(VI). To quantify these impacts, we studied an industrial waste landfill in the North of France that was contaminated with chromium. On the polluted area, the aquatic contamination is due to the slag heap as well as to chromium spots in soil. The soil contamination is mainly due to infiltration of chromium from the infill. The concentration of Cr(VI) in soil and water varies according to seasonal climatic variations and groundwater level. These variations have an effect on the Cr(VI) fate factor, in particular on transfer and residence time of the substance. This study underlines the spatial distribution of aquatic ecotoxicity and the temporal variation of freshwater ecotoxicity. We analysed the correlation between precipitation, temperature, concentration and ecotoxicity impact. With regards to the terrestrial ecotoxicity, the study focused on the vertical variation of the ecotoxicity and the major role of the soil layer composition into terrestrial pollution.     

Life cycle toxicity assessment of pesticides used in integrated and organic production of oranges in the Comunidad Valenciana, Spain

The relative impacts of 25 pesticides including acaricides, fungicides, herbicides, insecticides, and post-harvest fungicides, used in the production of oranges in Spain were assessed with current life cycle impact assessment (LCIA) tools. Chemical specific concentrations were combined with pesticide emission data and information on chemical toxicity to assess human toxicity and freshwater ecotoxicity impacts. As a case study, the relative impacts of two orange production systems in the region of Valencia, integrated pest management (IP) and organic production (OP), were assessed. The evaluation of active ingredients showed that on average acaricides have the highest human toxicity impact scores, while for freshwater ecotoxicity insecticides show the highest impact. In both impact categories the lowest impact scores were calculated for herbicides. In the production of 1 kg of orange fruits, where several kinds of pesticides are combined, results show that post-harvest fungicides can contribute more than 95% to the aggregate human toxicity impacts. More than 85% of aquatic ecotoxicity is generated by fungicides applied before harvest. The potential to reduce impacts on freshwater ecosystems is seven orders of magnitude, while impacts on human health can be reduced by two orders of magnitude. Hence, this stresses the importance of a careful pre-selection of active ingredients. In both impact categories, organic production represents the least toxic pest-control method.     

Comparison of toxicological impacts of integrated and chemical pest management in Mediterranean greenhouses

The goal of this paper is to assess the relative impacts of pest-control methods in greenhouses, based on current LCA tools. As a case study, the relative impacts of two tomato production methods, chemical pest management (CPM) and integrated pest management (IPM), are assessed. The amount of the active ingredients applied, the fate of the ingredients in the various greenhouse and environmental compartments, the human exposure routes via the various compartments and the inherent toxicity of the ingredients were taken into account in the relative impact calculations. To assess the importance of model selection in the assessment, pesticide-specific fate and exposure factors for humans and aquatic and terrestrial ecosystems, used to aggregate pesticide emissions, were calculated with two different models: (1) the USES-LCA model, adapted in order to calculate the pesticide transfer from greenhouse air and soil to fruits, and (2) the empirical model critical surface time (CST). Impact scores have in general shown a higher level of potential contamination in greenhouses treated with CPM compared to IPM (a factor of 1.4 to 2.3). Relative impacts have been shown highly dependent on the selection of specific pesticides and crop stage development at the moment of pesticide application. This means that both CPM and IPM could be improved by a careful selection of pesticides. In order to improve the relative impact calculations, future research in pesticide transfer to food will be necessary.     

Fate, effects and potential environmental risks of ethylene glycol: a review

The fate, effects, and potential environmental risks of ethylene glycol (EG) in the environment were examined. EG undergoes rapid biodegradation in aerobic and anaerobic environments (approximately 100% removal of EG within 24 h to 28 days). In air, EG reacts with photo-chemically produced hydroxyl radicals with a resulting atmospheric half-life of 2 days. Acute toxicity values (LC(50)s and EC(50)s) were generally >10,000 mg/l for fish and aquatic invertebrates. The data collectively show that EG is not persistent in air, surface water, soil, or groundwater, is practically non-toxic to aquatic organisms, and does not bioaccumulate in aquatic organisms. Potential long-term, quasi-steady state regional concentrations of EG estimated with a multi-media model for air, water, soil, and sediment were all less than predicted no effect concentrations (PNECs).     

Comparative toxicity of acrylic acid to marine and freshwater microalgae and the significance for environmental effects assessments.

In this study, we compared the sensitivity of freshwater and marine organisms to two structurally similar substances, acrylic acid and methacrylic acid. Reported acute toxicity data (L(E)C50-values) for freshwater organisms range from 0.1 to 222 mg/l and 85 to >130 mg/l for acrylic acid and methacrylic acid, respectively. The large variation in toxicity data for acrylic acid is due to a specific toxicity to certain species of freshwater microalgae, with algae EC50-values being two to three orders of magnitude lower than L(E)C50-values reported for fish and invertebrates. To evaluate the sensitivity of marine organisms, ecotoxicity data was generated for ten species of microalgae, one invertebrate species and one fish species. For methacrylic acid, we found a marine acute toxicity that ranged from 110 to >1260 mg/l, which is comparable to reported data on freshwater organisms. In strong contrast, the resulting L(E)C50-values for acrylic acid ranged from 50 to >1000 mg/l, and there was no specific sensitivity of marine algae when compared to marine invertebrates and fish. For acrylic acid, therefore, use of the available freshwater toxicity data for an effects assessment for the marine environment is likely to overestimate the hazard and risk from this substance. Overall, the results of the study suggest that ecotoxicity data generated on freshwater species may not always be appropriate for the effects assessments of organic chemicals in the marine environment, thus emphasising the importance of using ecologically relevant data to assess environmental risk.     

Statistical uncertainty in hazardous terrestrial concentrations estimated with aquatic ecotoxicity data

Since chemicals’ ecotoxic effects depend for most soil species on the dissolved concentration in pore water, the equilibrium partitioning (EP) method is generally used to estimate hazardous concentrations (HC50) in the soil from aquatic toxicity tests. The present study analyzes the statistical uncertainty in terrestrial HC50s derived by the EP-method. For 47 organic chemicals, we compared freshwater HC50s derived from standard aquatic ecotoxicity tests with porewater HC50s derived from terrestrial ecotoxicity tests. Statistical uncertainty in the HC50s due to limited species sample size and in organic carbon–water partitioning coefficients due to predictive error was treated with probability distributions propagated by Monte Carlo simulations. Particularly for specifically acting chemicals, it is very important to base the HC50 on a representative sample of species, composed of both target and non-target species. For most chemical groups, porewater HC50 values were approximately a factor of 3 higher than freshwater HC50 values. The ratio of the porewater HC50/freshwater HC50 was typically 3.0 for narcotic chemicals (2.8 for nonpolar and 3.4 for polar narcotics), 0.8 for reactive chemicals, 2.9 for neurotoxic chemicals (4.3 for AChE agents and 0.1 for the cyclodiene type), and 2.5 for herbicides–fungicides. However, the statistical uncertainty associated with this ratio was large (typically 2.3 orders of magnitude). For 81% of the organic chemicals studied, there was no statistical difference between the hazardous concentration of aquatic and terrestrial species. We conclude that possible systematic deviations between the HC50s of aquatic and terrestrial species appear to be less prominent than the overall statistical uncertainty.     

Ranking potential impacts of priority and emerging pollutants in urban wastewater through life cycle impact assessment

Life cycle impact assessment (LCIA), a feature of the Life cycle assessment (LCA) methodology, is used in this work outside the LCA framework, as a means to quantify the potential environmental impacts on ecotoxicity and human toxicity of wastewater containing priority and emerging pollutants. In order to do this, so-called characterisation factors are obtained for 98 frequently detected pollutants, using two characterisation models, EDIP97 and USES-LCA. The applicability of this methodology is shown in a case study in which wastewater influent and effluent samples from a Spanish wastewater treatment plant located in the Mediterranean coast were analysed. Characterisation factors were applied to the average concentration of each pollutant, obtaining impact scores for different scenarios: discharging wastewater to aquatic recipient, and using it for crop irrigation. The results show that treated wastewater involves a substantially lower environmental impact when compared to the influent, and pharmaceuticals and personal care products (PPCPs) are very important contributors to toxicity in this wastewater. Ciprofloxacin, fluoxetine, and nicotine constitute the main PPCPs of concern in this case study, while 2,3,7,8-TCDD, Nickel, and hexachlorobenzene are the priority pollutants with highest contribution. Nevertheless, it must be stressed that the new characterisation factors are based on very limited data, especially with regard to toxicology, and therefore they must be seen as a first screening to be improved in the future when more and higher quality data is available.     

Importance of considering pesticide stereoisomerism--proposal of a scheme to apply Directive 91/414/EEC framework to pesticide active substances manufactured as isomeric mixtures

An important gap has been detected in the application of the European framework for the evaluation of pesticide active substances constituted by enantiomeric and other kind of stereoisomeric mixtures. Up to date, little attention has been paid to the different biological properties of these compounds. Considering efficacy, toxicity, environmental fate and behaviour and ecotoxicity of separated isomers is necessary to fulfil Directive 91/414/EEC objectives of health and environment protection. Here, a critical review of this question for pesticide active substances is presented. An evaluative scheme for considering this question in the framework of Directive 91/414/EEC is also proposed.     

Implications of geographic variability on Comparative Toxicity Potentials of Cu, Ni and Zn in freshwaters of Canadian ecoregions

Current methods of estimating potential environmental impacts of metals in hazard and Life Cycle Impact Assessment (LCIA) do not consider differences in chemistry and landscape properties between geographic sites. Here, we developed and applied a model for regional aquatic impact characterization of metals using an updated method for estimating environmental fate factor (FF), bioavailability factor (BF) and aquatic ecotoxicity factor (EF). We applied the model to analyze differences in Comparative Toxicity Potentials (CTPs) of Cu, Ni and Zn for 24 Canadian ecoregions. The combined impacts of regional variability in ambient chemistry (in particular DOC, pH and hardness) and landscape properties (water residence time) can change the CTPs of these metals for freshwater by up to three orders of magnitude and change the relative ranking of metal hazard between ecoregions. Variation among Canadian freshwater chemistries and landscape characteristics influence the FFs within two orders of magnitude, BFs within two orders of magnitude for Ni and Zn and four orders of magnitude for Cu, and EFs within one order of magnitude. Sensitivity of metal FFs to environmental parameters alone spans three orders of magnitude when a constant water chemistry was used for all ecoregions. These results indicate that application of regionalised metal CTPs can have a significant influence in the analysis of ecotoxicological impacts in the life cycle assessment of products and processes.     

Aquatic ecotoxicity assessment of a new natural formicide

Background, aim and scope

Agrochemicals could reach aquatic ecosystems and damage ecosystem functionality. Natural formicide could be an alternative to use in comparison with the more toxic formicides available on the market. Thus, the objective of this study was to assess the ecotoxicity of the new natural formicide Macex? with a battery of classical aquatic ecotoxicity tests.

Material and methods

Bacteria (Aliivibrio fischeri), algae (Pseudokirchneriella subcapitata), hydra (Hydra attenuata), daphnids (Daphnia magna), and fish (Danio rerio) tests were performed in accordance with international standardized methodologies.

Results

In the range of formicide concentrations tested (0.03 to 2.0?g?L^?1) EC₅₀ values varied from 0.49 to >2.0?g?L^?1, with P. subcapitata being the most sensitive species and H. attenuata and D. rerio the most tolerant species to this product in aqueous solutions.

Conclusions

This new formicide preparation can be classed as a product of low toxicity compared to the aquatic ecotoxicity of the most common commercialized formicides.     

BETR North America: a regionally segmented multimedia contaminant fate model for North America

We present the Berkeley-Trent North American contaminant fate model (BETR North America), a regionally segmented multimedia contaminant fate model based on the fugacity concept. The model is built on a framework that links contaminant fate models of individual regions, and is generally applicable to large, spatially heterogeneous areas. The North American environment is modeled as 24 ecological regions, within each region contaminant fate is described using a 7 compartment multimedia fugacity model including a vertically segmented atmosphere, freshwater, freshwater sediment, soil, coastal water and vegetation compartments. Inter-regional transport of contaminants in the atmosphere, freshwater and coastal water is described using a database of hydrological and meteorological data compiled with Geographical Information Systems (GIS) techniques. Steady-state and dynamic solutions to the 168 mass balance equations that make up the linked model for North America are discussed, and an illustrative case study of toxaphene transport from the southern United States to the Great Lakes Basin is presented. Regionally segmented models such as BETR North America can provide a critical link between evaluative models of long-range transport potential and contaminant concentrations observed in remote regions. The continent-scale mass balance calculated by the model provides a sound basis for evaluating long-range transport potential of organic pollutants, and formulation of continent-scale management and regulatory strategies for chemicals.     

Environmental risk assessment of musk ketone and musk xylene in the Netherlands in accordance with the EU-TGD

An environmental risk assessment has been carried out for musk ketone and musk xylene according to the EU Technical Guidance Document for Environmental Risk Assessment for New and Existing Substances [1]. Musk ketone and musk xylene are used in fragrances for cosmetics and household products. For the fragrance industry these are important fragrance ingredients because of their excellent substantivity as well as for their unique smell, which determines largely the odor of a product.

The initial environmental risk assessment is based on information provided by the fragrance industry as represented in the Netherlands by its association NEA, by the Research Institute for Fragrance Materials (RIFM) and data reported in the international open literature. The risk assessment includes an evaluation of the risks for aquatic organisms in surface water and sediment and for soil organisms in soil after application of sewage sludge. Secondary poisoning of fish-eating birds and mammals is considered as well. For each compartment the Predicted Environmental Concentration (PEC) is compared to the Predicted No Effect Concentration (PNEC) to obtain PEC/PNEC ratios. Since monitoring data are available in water, sediment and fish, similar ratios are obtained with measured concentrations instead of the predicted ones.

For both substances, PEC/PNEC ratios are at or below 0.1 for organisms in the aquatic environment, including sediment organisms. PEC/PNEC ratios for fish-eating predators are 0.01. Ratios based on monitoring data are below 0.01 for all of these organisms. For soil organisms the PEC/PNEC ratio is 0.5 for musk ketone and 1.3 for musk xylene. Although in the Netherlands (as well as in some other European countries), sewage sludge presently finds no application as fertilizer on agricultural soil, the aim of environmental policy is to upgrade the sludge quality to enable future applications on agricultural and grassland. The reliability of the predicted soil concentrations can be greatly improved by obtaining experimental data on fate and behaviour of musk ketone and musk xylene in digested sludge and soil.

The risk assessment provides reassurance for the aquatic compartment while pointing the way for obtaining aditional data for the soil compartment.     

Terrestrial ecotoxicity and effect factors of metals in life cycle assessment (LCA)

Life cycle impact assessment aims to translate the amounts of substance emitted during the life cycle of a product into a potential impact on the environment, which includes terrestrial ecosystems. This work suggests some possible improvements in assessing the toxicity of metals on soil ecosystems in life cycle assessment (LCA). The current available data on soil ecotoxicity allow one to calculate the chronic terrestrial HC50(EC50) (hazardous concentration affecting 50% of the species at their EC50 level, i.e. the level where 50% of the individuals of the species are affected) of nine metals and metalloids (As(III) or (V), Be(II), Cr(III) or (VI), Sb(III) or (V), Pb(II), Cu(II), Zn(II) and Ni(II)). Contrarily to what is generally advised in LCIA, the terrestrial HC50 of metals shall not be extrapolated from the aquatic HC50, using the Equilibrium Partitioning method since the partition coefficient (K(d)) of metals is highly variable. The experimental ecotoxicology generally uses metallic salts to contaminate artificial soils but the comparison of the EC50 or NOEC obtained for the same metal with different salts reveals that the kind of salt used insignificantly influences these values. In contrast, depending on the metallic fraction of concern, the EC50 may vary, as for cadmium: the EC50 of Folsomia candida, expressed as free Cd in pore water is almost 2.5 orders of magnitude lower than that expressed as total metal. A similar result is obtained with Eisenia fetida, confirming the importance of metals speciation in assessing their impact on soils. By ranking the metals according to the difference between their terrestrial and aquatic HC50 values, two groups are distinguished, which match the hard soft acids and bases (HSAB) concept. This allows to estimate their affinity for soil components and potential toxicity according to their chemical characteristics.     

The water-soluble fraction of potentially toxic elements in contaminated soils: relationships between ecotoxicity, solubility and geochemical reactivity

To better understand the impacts posed by soil contamination to aquatic ecosystems it is crucial to characterise the links between ecotoxicity, chemical availability and geochemical reactivity of potentially toxic elements (PTE’s) in soils. We evaluated the adverse effects of water extracts obtained from soils contaminated by chemical industry and mining, using a test battery including organisms from different trophic levels (bacteria, algae and daphnids). These tests provided a quick assessment of the ecotoxicity of soils with respect to possible adverse effects on aquatic organisms although the ecotoxicological responses could be related to the solubility of PTE’s only to a limited extent.The analysis of results of bioassays together with the chemical characterisation of water extracts provided additional relevant insight into the role of conductivity, pH, Al, Fe, and Mn of soil extracts on toxicity to organisms. Furthermore, an important conclusion of this study was that the toxicity of extracts to the aquatic organisms could also be related to the soil properties (pH, Org C and Fe_ox) and to the reactivity of PTE’s in soils which in fact control the soluble fraction of the contaminants.The combined assessment of ecotoxicity in water fractions, solubility and geochemical reactivity of PTE’s in soils provided a more comprehensive understanding of the bioavailability of inorganic contaminants than ecotoxicological or chemical studies alone and can therefore be most useful for environmental risks assessment of contaminated soils.