Quality control for sampling of PCDD/PCDF emissions from open combustion sources

Both long duration (>6 h) and high temperature (up to 139 °C) sampling efforts were conducted using ambient air sampling methods to determine if either high volume throughput or higher than ambient air sampling temperatures resulted in loss of target polychlorinated dibenzodioxins/dibenzofurans (PCDDs/PCDFs) from a polyurethane foam (PUF) sorbent. Emissions from open burning of simulated military forward operating base waste were sampled using EPA Method TO-9A for 185 min duration using a filter/PUF/PUF in series combination. After a 54 m³ sample was collected, the sampler was removed from the combustion source and the second PUF was replaced with a fresh, clean PUF. An additional 6 h of ambient air sampling (171 m³) was conducted and the second PUF was analyzed to determine if the PCDD/PCDF transferred from the filter and the first PUF. Less than 4.4% of the initial PCDD/PCDF was lost to the second PUF. To assess the potential for blow off of PCDD/PCDF analytes during open air sampling, the mobility of spiked mono- to hepta-PCDD/PCDF standards across a PUF sorbent was evaluated from ambient air temperatures to 145 °C with total volumes between 600 L and 2400 L. Lower molecular weight compounds and higher flow amounts increased release of the spiked standards consistent with vapor pressure values. At 600 L total sampled volume, the release temperature for 1% of the tetra-CDD (the lowest chlorinated homologue with a toxic compound) was 87 °C; increasing the volume fourfold reduced this temperature to 73 °C.     

Hydraulic performance of a proposed in situ photocatalytic reactor for degradation of MTBE in water

Methyl tert-butyl ether (MTBE) groundwater remediation projects often require a combination of technologies resulting in increasing the project costs. A cost-effective in situ photocatalytic reactor design, Honeycomb II, is proposed and tested for its efficiency in MTBE degradation at various flows. This study is an intermediate phase of the research in developing an in situ photocatalytic reactor for groundwater remediation. It examines the effect of the operating variables: air and water flow and double passages through Honeycomb II, on the MTBE removal. MTBE vaporisation is affected by not only temperature, Henry’s law constant and air flow to volume ratio but also reactor geometry. The column reactor achieved more than 84% MTBE removal after 8 h at flows equivalent to horizontal groundwater velocities slower than 21.2 cm d⁻¹. Despite the contrasting properties between a photocatalytic indicator methylene blue and MTBE, the reactor efficiency in degrading both compounds showed similar responses towards flow (equivalent groundwater velocity and hydraulic residence time (HRT)). The critical HRT for both compounds was approximately 1 d, which corresponded to a velocity of 21.2 cm d⁻¹. A double pass through both new and used catalysts achieved more than 95% MTBE removal after two passes in 48 h. It also verified that the removal efficiency can be estimated via the sequential order of the removal efficiency of one pass obtained in the laboratory. This study reinforces the potential of this reactor design for in situ groundwater remediation.     

Monitoring heavy metal concentrations in leachates from a forest soil subjected to repeated applications of sewage sludge

The aim of the study was to establish whether the repeated application of sewage sludge to an acid forest soil (Dystric Cambisol) would lead to short-term groundwater contamination. Sludge was applied at four loading rates (0, 2.4, 17 and 60 Mg ha⁻¹) in two consecutive years and leachates were analysed. Heavy metal inputs to soils at the lowest dose were below EC regulations but, at higher doses, limits for Zn, Cd, Cr and Ni were exceeded. Repeated application of sludge at 60 Mg ha⁻¹ resulted in significantly (P < 0.05) higher concentrations of Zn, Cd, Cr and Ni in the leachates than with other treatments. The drinking water standards for Cd and Ni were surpassed in all treatments. Control plots were contaminated by groundwater flow despite the existence of buffer zones between plots. This complicated interpretation of the results, highlighting the importance of careful design of this type of experiment.     

Phenol depletion by thermally activated peroxydisulfate at 70°C

The ability of thermal activated peroxydisulfate (PS) of mineralizing phenol at 70 °C from contaminated waters is investigated. Phenol in concentrations of 10⁻⁴ to 5 × 10⁻⁴ M is quantitatively depleted by 5 × 10⁻³ to 10⁻² M activated PS in 15 min of reaction. However, mineralization of the organic carbon is not observed. Instead, an insoluble phenol polymer-type product is formed. A reaction mechanism including the formation of phenoxyl radicals and validated by computer simulations is proposed. High molecular weight phenolic products are formed by phenoxyl radical H-abstraction reactions. This is not the case for the room temperature degradation of phenol by sulfate radicals where sulfate addition to the aromatic ring mainly leads to the generation of hydroxycyclohexadienyl radicals leading to hydroxybenzenes and oxidized open chain products. Therefore, a change in the reaction mechanism is observed with increasing temperature, and thermal activation of PS at 70 °C does not lead to the mineralization of phenol. Thus PS activation at 70 °C may be considered a potential method to reduce the load of phenol in polluted waters by polymerization.     

Biodegradation of multiple cyanobacterial metabolites in drinking water supplies

The fate of multiple cyanobacterial metabolites was assessed in two Australian source waters. The saxitoxins were the only metabolites shown to be non-biodegradable in Myponga Reservoir water, while microcystin-LR (MCLR) and geosmin were biodegradable in this water source. Likewise, cylindrospermopsin (CYN) was shown to be biodegradable in River Murray water. The order of ease of biodegradability followed the trend: MCLR > CYN > geosmin > saxitoxins. Biodegradation of the metabolites was affected by temperature and seasonal variations with more rapid degradation at 24 °C and during autumn compared with 14 °C and during winter. A microcystin-degrading bacterium was isolated and shown to degrade four microcystin variants within 4 h. This bacterium, designated as TT25, was shown to be 99% similar to a Sphingopyxis sp. based on a 16S rRNA gene fragment. Isolate TT25 was shown to contain a homologue of the mlrA gene; the sequence of which was 99% similar to that of a previously reported microcystin-degrader. Furthermore, isolate TT25 could degrade the microcystins in the presence of copper sulphate (0.5 mg L⁻¹ as Cu²⁺) which is advantageous for water authorities dosing such algicides into water bodies to control cyanobacterial blooms.     

Effect of vegetation in pilot-scale horizontal subsurface flow constructed wetlands treating sulphate rich groundwater contaminated with a low and high chlorinated hydrocarbon

In order to characterize the effect of vegetation on performance of constructed wetlands (CWs) treating low and high chlorinated hydrocarbon, two pilot-scale horizontal subsurface flow (HSSF) CWs (planted with Phragmites australis and unplanted) treating sulphate rich groundwater contaminated with MCB (monochlorobenzene, as a low chlorinated hydrocarbon), (about 10 mg L⁻¹), and PCE (perchloroethylene, as a high chlorinated hydrocarbon), (about 2 mg L⁻¹), were examined. With mean MCB inflow load of 299 mg m⁻² d⁻¹, the removal rate was 58 and 208 mg m⁻² d⁻¹ in the unplanted and planted wetland, respectively, after 4 m from the inlet. PCE was almost completely removed in both wetlands with mean inflow load of 49 mg m⁻² d⁻¹. However, toxic metabolites cis-1,2-DCE (dichloroethene) and VC (vinyl chloride) accumulated in the unplanted wetland; up to 70% and 25% of PCE was dechlorinated to cis-1,2-DCE and VC after 4 m from the inlet, respectively. Because of high sulphate concentration (around 850 mg L⁻¹) in the groundwater, the plant derived organic carbon caused sulphide formation (up to 15 mg L⁻¹) in the planted wetland, which impaired the MCB removal but not statistically significant. The results showed significant enhancement of vegetation on the removal of the low chlorinated hydrocarbon MCB, which is probably due to the fact that aerobic MCB degraders are benefited from the oxygen released by plant roots. Vegetation also stimulated completely dechlorination of PCE due to plant derived organic carbon, which is potentially to provide electron donor for dechlorination process. The plant derived organic carbon also stimulated dissimilatory sulphate reduction, which subsequently have negative effect on MCB removal.     

Environmentally friendly assessment of organic compound bioaccessibility using sub-critical water

The evaluation of microbial availability of contaminants is of high importance for better reflecting the processes governing contaminant fate in soil and for establishing the risk associated with contaminated sites. A sub-critical water extraction technique was assessed for its potential to determine the microbially degradable fraction of [¹⁴C]phenanthrene-associated activity in two dissimilar soils at three different ageing times (14, 28 and 49 days). For the majority of determinations, no significant (p > 0.05) difference between sub-critical water-extracted ¹⁴C-activity at 160 °C and the fraction mineralized by catabolically active Pseudomonas sp. was observed. Collectively, the results suggested that the sub-critical water extraction technique was an appropriate technique for predicting the biodegradable fraction of phenanthrene-associated ¹⁴C-activity in dissimilar soils following increasing soil-contaminant contact time.     

Long-term effect of temperature on bioaccumulation of dietary metals and metallothionein induction in Sparus aurata

Previous studies have demonstrated that the commercial feed of aquacultured fish contains trace amounts of toxic and essential metals which can accumulate in tissues and finally be ingested by consumers. Recently rising temperatures, associated to the global warming phenomenon, have been reported as a factor to be taken into consideration in ecotoxicology, since temperature-dependent alterations in bioavailability, toxicokinetics and biotransformation rates can be expected. Sparus aurata were kept at 22 °C, 27 °C and 30 °C for 3 months in order to determine the temperature effect on metallothionein induction and metal bioaccumulation from a non-experimentally contaminated commercial feed. A significant temperature-dependent accumulation of cadmium (Cd), copper (Cu), mercury (Hg), zinc (Zn), lead (Pb) and iron (Fe) was found in liver, together with that of manganese (Mn), Fe and Zn in muscle. Hg presented the highest bioaccumulation factor, and essential metal homeostasis was disturbed in both tissues at warm temperatures. An enhancement of hepatic metallothionein induction was found in fish exposed to the highest temperature.     

Potential use of DNA adducts to detect mutagenic compounds in soil

In this study, three different soils with contrasting features, spiked with 300 mg benzo[a]pyrene (BaP)/kg dry soil, were incubated at 20 °C and 60% water holding capacity for 540 days. At different time points, BaP and DNA were extracted and quantified, and DNA adducts were quantified by ³²P-postlabelling. After 540 days incubation, 69.3, 81.6 and 83.2% of initial BaP added remained in Cruden Bay, Boyndie and Insch soils, respectively. Meanwhile, a significantly different amount of DNA-BaP adducts were found in the three soils exposed to BaP over time. The work demonstrates the concept that DNA adducts can be detected on DNA extracted from soil. Results suggest the technique is not able to directly reflect bioavailability of BaP transformation products. However, this new method provides a potential way to detect mutagenic compounds in contaminated soil and to assess the outcomes of soil remediation.     

Polarity effect of pulsed corona discharge for the oxidation of gaseous elemental mercury

The effect of polarity on the oxidation of Hg⁰ was examined in the presence of O₂ via a pulsed corona discharge (PCD). The experimental result showed no difference in the energy yield of Hg⁰ oxidation at both positive and negative PCDs (∼8 μg Hg W h⁻¹ at following conditions: total flow rate = 2 L min⁻¹ (Hg⁰ = 50 μg N m⁻³, O₂ = 10%, and N₂ balance), temperature = 150 °C, and specific energy density = 5-15 W h N m⁻³). This suggests that the positive PCD process used to control gaseous air pollutants may play an essential key role in Hg⁰ oxidation because it consumes enough energy (∼15 W h N m⁻³) but an electrical precipitator could not because it consumes less energy (∼0.3 W h N m⁻³) to oxidize Hg⁰.     

Deposition fluxes of PCDD/Fs in a reservoir system in northern Taiwan

In this study, polychlorinated dibenzo-p-dioxin and dibenzofuran (PCDD/F) concentrations and depositions in ambient air, water column and sediment were measured at a coupled reservoir-watershed system in northern Taiwan. The atmospheric PCDD/F concentration measured in the vicinity of the reservoir ranged from 4.9 to 39 fg I-TEQ m⁻³ and the Asian dust storm in February accounted for the peak value, which corresponded to a total suspended particle concentration of 128 μg m⁻³. The atmospheric PCDD/F deposition ranged from 1.4 to 19 pg I-TEQ m⁻² d⁻¹, with higher deposition occurring during winter and spring (long-range transport events). During summer, when atmospheric deposition is lower, consecutive tropical cyclones (typhoons) bring heavy rainfall that enhances soil erosion and creates turbidity-driven intermediate flow. This results in significantly higher PCDD/F deposition in water column of the reservoir at 70 m water depth (179 pg I-TEQ m⁻² d⁻¹) than at 20 m (21 pg I-TEQ m⁻² d⁻¹) during typhoon event. The accumulation rate of PCDD/Fs (9.1 ng I-TEQ m⁻² y⁻¹) in the reservoir sediments (depth: 0-2 cm) was consistent with PCDD/F deposition obtained from water column (6.1 and 8.3 ng I-TEQ m⁻² y⁻¹); however, it is significantly higher when compared to the atmospheric deposition (2.0 ng I-TEQ m⁻² y⁻¹). Based on the mass balance between the measurements of atmospheric deposition and sinking particles in water column, around 54-74% of PCDD/F inputs into the reservoir were contributed by the catchment erosion during normal period. However, the PCDD/F input contributed by the enhanced catchment erosion significantly increased to 90% during intensive typhoon events.     

Suppressive effect of polychlorinated dibenzo-p-dioxins, polychlorinated dibenzofurans and dioxin-like polychlorinated biphenyls transfer from feed to eggs of laying hens by activated carbon as feed additive

In this study, we investigated the suppressive effect of polychlorinated dibenzo-p-dioxins (PCDDs), polychlorinated dibenzofurans (PCDFs), and dioxin-like polychlorinated biphenyls (DL-PCBs) transfer from the feed to the eggs of laying hens by using activated carbon as a feed additive. Four groups of six hens (White Leghorn egg-layers; age, 11 weeks) were housed as two control groups and two exposure groups for a period of 20 weeks. Two control groups were fed with either the basal feed “Control” or basal feed additing activated carbon “Control + C”. Another two exposure groups were fed with feed contaminated (about 6 ng TEQ kg⁻¹ feed) by standard solutions of PCDDs/PCDFs and DL-PCBs “Exposure” alone and contaminated feed adding activated carbon “Exposure + C”. There was no significant effect on each groups for the growth rate, biochemical blood components, and egg production: these were around the standard levels for poultry in general. Moreover the results in this study showed the availability of activated carbon as a feed additive owing to the reduction in the risk of food pollution by PCDDs/PCDFs and DL-PCBs. The concentration in the eggs of the Exposure group gradually increased following the start of egg-laying but reached a steady state after about 1 month. In contrast, the concentration for the Exposure + C group was stationary and below the maximum EU level (6 pg TEQ g⁻¹ fat). In comparison to the Exposure group, the Exposure + C group showed a significant decline in the percentage of bioaccumulation into the egg. This reduction due to activated carbon was also observed in the muscle and abdominal fat. The reductions were compound- and congener-dependent for DL-PCBs as follows: PCDDs/PCDFs, non-ortho-PCBs, and mono-ortho-PCBs were more than 90%, 80%, and 50%, respectively, irrespective of the type of tissues. Fat soluble vitamin concentrations in the eggs of the Exposure + C group showed lower trends than the Exposure group. The γ-tocopherol and α-tocopherol concentrations in eggs of Exposure + C group showed a significant reduction of about 40%. However, the addition of activated carbon into animal feed could obviate the remote potential for accidents causing unintentional food pollution with PCDDs/PCDFs and DL-PCBs.     

Adsorption behavior of perfluorooctanesulfonate (PFOS) and perfluorooctanoate (PFOA) on boehmite

Understanding the interaction of perfluorochemicals, persistent pollutants with known human health effects, with mineral compounds in surface water and groundwater environments is essential to determining their fate and transport. Kinetic experiments showed that adsorption equilibrium can be achieved within 48 h and the boehmite (AlOOH) surface is receptive to perfluorooctanesulfonate (PFOS) and perfluorooctanoate (PFOA) adsorption. The adsorption isotherms estimated the maximum adsorption capacities of PFOS and PFOA on boehmite as 0.877 μg m⁻² and 0.633 μg m⁻², respectively. Compared to the adsorption capacity on γ-alumina, the abundant hydroxyl groups on boehmite surfaces resulted in the 2-3 times higher adsorption of PFOS and PFOA. Increasing solution pH led to a moderate decrease in PFOS and PFOA adsorption, owing to an increase in ligand exchange reactions and the decrease of electrostatic interactions. The presence of NaCl and CaCl₂ in solution demonstrated negative effects for PFOS and PFOA adsorption on boehmite surfaces, with potential mechanisms being electrical double layer compression, competitive adsorption of chloride, and the Ca²⁺ bridging effect between perfluorochemicals.     

Atmospheric partitioning and the air–water exchange of polycyclic aromatic hydrocarbons in a large shallow Chinese lake (Lake Chaohu)

The residual levels of polycyclic aromatic hydrocarbons (PAHs) in the atmosphere and in dissolved phase from Lake Chaohu were measured by (GC–MS). The composition and seasonal variation were investigated. The diffusive air–water exchange flux was estimated by a two-film model, and the uncertainty in the flux calculations and the sensitivity of the parameters were evaluated. The following results were obtained: (1) the average residual levels of all PAHs (PAH16) in the atmosphere from Lake Chaohu were 60.85 ± 46.17 ng m⁻³ in the gaseous phase and 14.32 ± 23.82 ng m⁻³ in the particulate phase. The dissolved PAH16 level was 173.46 ± 132.89 ng L⁻¹. (2) The seasonal variation of average PAH16 contents ranged from 43.09 ± 33.20 ng m⁻³ (summer) to 137.47 ± 41.69 ng m⁻³ (winter) in gaseous phase, from 6.62 ± 2.72 ng m⁻³ (summer) to 56.13 ± 22.99 ng m⁻³ (winter) in particulate phase, and 142.68 ± 74.68 ng L⁻¹ (winter) to 360.00 ± 176.60 ng L⁻¹ (summer) in water samples. Obvious seasonal trends of PAH16 concentrations were found in the atmosphere and water. The values of PAH16 for both the atmosphere and the water were significantly correlated with temperature. (3) The monthly diffusive air–water exchange flux of total PAH16 ranged from −1.77 × 10⁴ ng m⁻² d⁻¹ to 1.11 × 10⁵ ng m⁻² d⁻¹, with an average value of 3.45 × 10⁴ ng m⁻² d⁻¹. (4) The results of a Monte Carlo simulation showed that the monthly average PAH fluxes ranged from −3.4 × 10³ ng m⁻² d⁻¹ to 1.6 × 10⁴ ng m⁻² d⁻¹ throughout the year, and the uncertainties for individual PAHs were compared. (5) According to the sensitivity analysis, the concentrations of dissolved and gaseous phase PAHs were the two most important factors affecting the results of the flux calculations.     

Estrogen receptor mediated activity in bankside groundwater, with flood suspended particulate matter and floodplain soil - an approach combining tracer substance, bioassay and target analysis

Bankside groundwater is widely used as drinking water resource and, therefore, contamination has to be avoided. In the European Union groundwater protection is explicit subject to Water Framework Directive. While groundwater pollution may originate from different sources, this study investigated on impacts via flood events.Groundwater was sampled with increasing distance to the river Rhine near Karlsruhe, Germany. Samples were HPLC-MS-MS analyzed for the river contaminant carbamazepine to indicate river water infiltration, giving permanent presence in 250 m distance to the river (14-47 μg L⁻¹). Following a flood event, concentrations of about 16-20 μg L⁻¹ could also be detected in a distance of 750 m to the river. Furthermore, estrogenic activity as determined with the Yeast Estrogen Screen assay was determined to increase up to a 17β-ethinylestradiol equivalent concentration (E-EQ) = 2.9 ng L⁻¹ near the river, while activity was initially measured following the flood with up to E-EQ = 2.6 ng L⁻¹ in 750 m distance. Detections were delayed with increasing distance to the river indicating river water expansion into the aquifer.Flood suspended matter and floodplain soil were fractionated and analyzed for estrogenic activity in parallel giving up to 1.4 ng g⁻¹ and up to 0.7 ng g⁻¹, respectively. Target analysis focusing on known estrogenic active substances only explained <1% of measured activities.Nevertheless, river water infiltration was shown deep into bankside groundwater, thus, impacting groundwater quality. Therefore, flood events have to be in the focus when aiming for groundwater and drinking water protection as well as for implementation of Water Framework Directive.     

Dry deposition and soil-air gas exchange of polychlorinated biphenyls (PCBs) in an industrial area

Ambient air and dry deposition, and soil samples were collected at the Aliaga industrial site in Izmir, Turkey. Atmospheric total (particle + gas) ∑₄₁-PCB concentrations were higher in summer (3370 ± 1617 pg m⁻³, average + SD) than in winter (1164 ± 618 pg m⁻³), probably due to increased volatilization with temperature. Average particulate ∑₄₁-PCBs dry deposition fluxes were 349 ± 183 and 469 ± 328 ng m⁻² day⁻¹ in summer and winter, respectively. Overall average particulate deposition velocity was 5.5 ± 3.5 cm s⁻¹. The spatial distribution of ∑₄₁-PCB soil concentrations (n = 48) showed that the iron-steel plants, ship dismantling facilities, refinery and petrochemicals complex are the major sources in the area. Calculated air-soil exchange fluxes indicated that the contaminated soil is a secondary source to the atmosphere for lighter PCBs and as a sink for heavier ones. Comparable magnitude of gas exchange and dry particle deposition fluxes indicated that both mechanisms are equally important for PCB movement between air and soil in Aliaga.     

Phosphine in paddy fields and the effects of environmental factors

Ambient levels of phosphine (PH₃) in the air, phosphine emission fluxes from paddy fields and rice plants, and the distribution of matrix-bound phosphine (MBP) in paddy soils were investigated throughout the growing stages of rice. The relationships between MBP and environmental factors were analyzed to identify the principal factors determining the distribution of MBP. The phosphine ambient levels ranged from 2.368 ± 0.6060 ng m⁻³ to 24.83 ± 6.529 ng m⁻³ and averaged 14.25 ± 4.547 ng m⁻³. The highest phosphine emission flux was 22.54 ± 3.897 ng (m² h)⁻¹, the lowest flux was 7.64 ± 4.83 ng (m² h)⁻¹, and the average flux was 14.17 ± 4.977 ng (m² h)⁻¹. Rice plants transport a significant portion of the phosphine emitted from the paddy fields. The highest contribution rate of rice plants to the phosphine emission fluxes reached 73.73% and the average contribution was 43.00%. The average MBP content of 111.6 ng kg⁻¹fluctuated significantly in different stages of rice growth and initially increased then decreased with increasing depth. The peak MBP content in each growth stage occurred approximately 10 cm under the surface of paddy soils. Pearson correlation analyses and stepwise multiple regression analysis showed that soil temperature (Ts), acid phosphatase (ACP) and total phosphorus (TP) were the principal environmental factors, with correlative rankings of Ts > ACP > TP.     

Uranium in Kosovo’s drinking water

The results of this paper are an initiation to capture the drinking water and/or groundwater elemental situation in the youngest European country, Kosovo. We aim to present a clear picture of the natural uranium concentration in drinking water and/or groundwater as it is distributed to the population of Kosovo. Nine hundred and fifty-one (951) drinking water samples were analyzed by inductively coupled plasma mass spectrometry (ICPMS). The results are the first countrywide interpretation of the uranium concentration in drinking water and/or groundwater, directly following the Kosovo war of 1999. More than 98% of the samples had uranium concentrations above 0.01 μg L⁻¹, which was also our limit of quantification. Concentrations up to 166 μg L⁻¹ were found with a mean of 5 μg L⁻¹ and median 1.6 μg L⁻¹ were found. Two point six percent (2.6%) of the analyzed samples exceeded the World Health Organization maximum acceptable concentration of 30 μg L⁻¹, and 44.2% of the samples exceeded the 2 μg L⁻¹ German maximum acceptable concentrations recommended for infant food preparations.     

VFA generation from waste activated sludge: effect of temperature and mixing

The success of enhanced biological phosphorus removal (EBPR) depends on the constant availability of volatile fatty acids (VFAs). To reduce costs, waste streams would be a preferred source. Since VFAs were shown to vary in the incoming sewage and fermentate from primary sludge the next available source is waste activated sludge (WAS). The opportunity is particularly good in plants where WAS is stored before shipment. Little information is however available on the rate of VFA release from such sludge, especially at the lower temperatures and under the storage conditions typically found in colder climates. Bench-scale batch tests were performed to investigate the effect of temperature and requirement for mixing on VFA generation from WAS generated in full scale non-EBPR wastewater treatment plant. WAS fermentation was found highly temperature-dependent. Hydrolysis rate constant (k_h) values of 0.17, 0.08 and 0.04 d⁻¹ at 24.6, 14 and 4 °C were obtained, respectively. Arrhenius temperature coefficient was calculated to be 1.07. It took 5 d to complete hydrolysis at 24.6 °C, 7 d at 14 °C, and 9 d at 4 °C. The fermentation lasted for 20 d. At 24.6 °C the mixed reactor reached 84% of the overall VFA production only in 5 d. When temperature dropped to 14 and 4 °C, the ratio of VFA production at day 10 to overall VFA production in the mixed reactor were 62% and 48%, respectively. The overall VFA-COD concentration in the non-mixed reactors was much lower than the mixed reactors. The information is important for the designer as there was uncertainty with the effect of temperature and mixing on sludge fermentation.     

Activated soil filters for removal of biocides from contaminated run-off and waste-waters

Building facades can be equipped with biocides to prevent formation of algal, fungal and bacterial films. Thus run-off waters may contain these highly active compounds. In this study, the removal of several groups of biocides from contaminated waters by means of an activated soil filter was studied.A technical scale activated vertical soil filter (biofilter) with different layers (peat, sand and gravel), was planted with reed (Phragmites australis) and used to study the removal rates and fate of hydrophilic to moderate hydrophobic (log K_ow 1.8-4.4) biocides and biocide metabolites such as: Terbutryn, Cybutryn (Irgarol® 1051), Descyclopropyl-Cybutryn (Cybutryn and Terbutryn metabolite), Isoproturon, Diuron, and its metabolite Diuron-desmonomethyl, Benzo-isothiazolinone, n-Octyl-isothiazolinone, Dichloro-n-octylisothiazolinone and Iodocarbamate (Iodocarb). Three experiments were performed: the first one (36 d) under low flow conditions (61 L m⁻² d⁻¹) reached removal rates between 82% and 100%. The second one was performed to study high flow conditions: During this experiment, water was added as a pulse to the filter system with a hydraulic load of 255 L m⁻² within 5 min (retention time <1 h). During this experiment the removal rates of the compounds decreased drastically. For five compounds (Cybutryn, Descyclopropyl-Cybutryn, Diuron, Isoproturon, and Iodocarb) the removal dropped temporarily below 60%, while it was always above 70% for the others (Terbutryn, Benzo-isothiazolinone, n-Octyl-isothiazolinone, Dichloro-n-octylisothiazolinone). However, this removal is a considerable improvement compared to direct discharge into surface waters or infiltration into soil without appropriate removal. In the last experiment the removal efficiencies of the different layers were studied. Though the peat layer was responsible for most of the removal, the sand and gravel layers also contributed significantly for some compounds. All compounds are rather removed by degradation than by sorption.