催化剂对甲醛废水湿式氧化的增效作用

在设定的湿式氧化条件下 ,从若干种金属盐中筛选了Cu(NO3) 2 作为氧化甲醛废水的催化剂 ,考察了Cu(NO3) 2 用量、废水的初始浓度及温度对有机物去除率的影响 ,结果表明 :Cu(NO3) 2 以 5mg·l- 1 Cu2 计量投加为宜 ,甲醛初始浓度在 480mg·l- 1 — 1 5 0 0mg·l- 1 范围内一直保持较高的去除率 ,反应的适宜温度为 1 40℃以上 ;根据反应过程数据建立了该催化氧化反应的分段一级动力学模型 ,求得甲醛氧化动力学模型快、慢步骤的表观活化能分别为7 2 9kJ·mol- 1 和 1 4 45kJ·mol- 1 ;而COD降解动力学模型快、慢步骤的表观活化能则分别为2 0 47kJ·mol- 1 和 2 9 5 2kJ·mol- 1 .     

H2O2热氧化降解硝基苯废水的机理和动力学

利用H2O2为氧化剂,高温密闭条件下对硝基苯废水进行了降解研究.通过正交实验,分析了氧化剂种类、硝基苯初始浓度、反应温度和反应时间对硝基苯降解率的影响.利用HPLC分别对降解过程产物进行了分析,实验结果表明:H2O2在密闭高温条件下形成的自由基攻击硝基苯分子,硝基苯降解过程按硝基苯→硝基酚类→二氧化碳和水的途径进行,降解过程中产生的微量邻、间、对硝基酚类物质不会累积.H2O2在反应过程中消耗不显著,具有相对的化学稳定性.H2O2热氧化硝基苯的降解反应符合一级动力学方程,反应表观速率常数K表观=0.0073 min-1.     

电催化氧化阳极制备及其降酚特性

以自制Ti基SnO2/Sb2O3/IrO2镀层形稳电极(Dimensionless Stable Anode)为阳极,采用电催化氧化法处理模拟含酚废水.通过涂层分析和电化学性能测试表征了自制电极特性,考察了电解质类型和浓度、电流密度、苯酚初始浓度及体系初始pH值等因素对苯酚氧化过程的影响,并探讨其降解动力学规律.结果表明,自制电极是以SnO2为基础的纳米级固熔体氧化物电极且具有较好的表面结构,运行稳定性较好.苯酚的降解主要依赖于以NaCl为电解质时产生的氯系活性物质的间接氧化作用.随着电解质浓度及电流密度的增加,苯酚降解速率随之增大;而苯酚的初始浓度越大,降解速率越慢.体系初始pH对过程影响不明显.苯酚的降解过程符合一级反应动力学。     

Al~0-O_2体系降解活性黄3RS溶液

酸性条件下,采用Al0-O2体系对活性黄3RS染料溶液进行降解,考察了活性黄3RS的初始浓度,p H、Al0的浓度、温度、Fe2+浓度等因素对其降解率的影响.结果表明,在p H=2和Al0浓度为1 g·L-1时,对50 mg·L-1活性黄3RS的降解率最高,反应150 min时最高可获得92%的降解率;降解后其COD值由126.35 mg·L-1降至49.44 mg·L-1;温度升高,活性黄3RS的降解率提高,其表观反应活化能为108.262 k J·mol-1;动力学分析表明该过程为一级反应,反应速率常数kobs=1.2×10-2s-1;当向体系中加入Fe2+时,其降解速率加快.     

α-MnO2/水界面磺胺嘧啶的氧化降解动力学

通过反歧化法合成α-MnO2,并以α-MnO2为氧化剂,研究了不同锰氧化物剂量、不同磺胺嘧啶初始浓度和不同pH值下α-MnO2/水界面磺胺嘧啶的氧化降解动力学,并讨论了不同的反应条件对反应动力学的影响.结果表明,α-MnO2可以有效的氧化降解甚至矿化磺胺嘧啶,反应符合准一级反应动力学方程,在25 ℃,pH 4.6的反应条件下,反应120 min后,11.5 mmol·L-1的α-MnO2对0.02 mmol·L-1磺胺嘧啶去除率达到99.98%.α-MnO2剂量和磺胺嘧啶的初始浓度均与磺胺嘧啶氧化降解的动力学常数呈显著正相关关系,相关因子分别为0.67和0.18,相关系数R分别达到0.9961和0.9979;而磺胺嘧啶的降解动力学常数与体系的pH则呈显著负相关关系,相关因子为-0.25,相关系数R达到0.9975.初步探讨了锰氧化物氧化降解磺胺嘧啶机理.研究表明,土壤及沉积物中的锰氧化物可以有效促进其中残留抗生素类药物磺胺嘧啶的降解消除过程.     

UV-254 nm活化过硫酸盐降解麻黄碱的影响因素和机理

采用UV-254 nm活化过硫酸盐高级氧化技术去除水中污染物麻黄碱(EPH),并研究了其降解动力学过程和降解机理.考察了过硫酸盐(PS)投加量、EPH的初始浓度、不同pH值及不同离子(HCO~-_3、NO~-_3、Cl~-)对降解效果的影响.结果表明,UV-254 nm活化过硫酸盐工艺能有效去除实验条件下的EPH,其氧化降解反应符合二级动力学方程.EPH去除率随着PS投加量的增加而增大.pH对降解反应有较大的影响,在pH=7的条件下,反应速率最快,表观反应动力学常数(k_(obs))为0.467 min~(-1).进一步研究表明,HCO~-_3、NO~-_3和Cl~-对EPH的降解都存在抑制作用,在相同浓度下,其抑制程度依次为Cl~- NO~-_3 HCO~-_3.通过UPLC-MS/MS鉴定了麻黄碱降解的中间体,并提出了可能的降解机理和转化途径.     

氯化四(4-磺酸钠苯基)卟啉铁(Ⅲ)催化过氧化氢氧化降解2,4,6-三氯苯酚的动力学研究

用紫外-可见分光光度法研究了水溶性金属卟啉Fe(TPPS)Cl催化H2O2氧化降解2,4,6-三氯苯酚(TCP)的动力学(TPPS为四(4-磺酸钠苯基)卟啉),探讨了反应体系酸度、H2O2/Fe(TPPS)Cl物质的量之比、温度对氧化降解速率的影响,提出了反应机理,建立了反应动力学数学模型.研究结果表明,TCP初始浓度为3.8×10-4 mol.L-1、Fe(TPPS)Cl浓度为4.0×10-5 mol.L-1、H2O2浓度为1.8×10-3mol.L-1、温度为25℃、pH值为6.8、反应时间为90 min时,TCP的降解率可达到99%,其表观活化能为10.96 kJ.mol-1.因此,Fe(TPPS)Cl作为模拟过氧化物酶在催化降解TCP过程中是一种有效的催化剂.     

模拟日光-非均相Fenton光催化降解喹啉

以铝-分子筛(Al-MCM-41)为载体,采用加热回流法制备一种非均相芬顿催化剂还原氧化石墨烯-羟基铁/Al-MCM-41(r GO-Fe OOH/Al-MCM-41).以喹啉模拟有机废水,考察该催化剂在不同氧化体系、不同H_2O_2投加量、不同催化剂投加量和不同水质因素(喹啉初始浓度和p H值)条件下对喹啉降解效能的影响,同时考察了催化剂的重复使用性.结果表明,喹啉的光芬顿降解过程符合准一级反应动力学,降解过程中溶液中的NO-3浓度先升高后下降,表明喹啉的吡啶环被打开.对比芬顿反应,模拟日光芬顿反应中光的引入促进羟基自由基的产生,使得喹啉去除率由45%提高到了99%;喹啉降解速率随着催化剂和H_2O_2投加量的增加而升高,但投加量过多会消耗·OH自由基从而抑制喹啉降解,在光芬顿体系中,该催化剂在p H=3.6—9.6的范围内都表现出了很高的活性;当喹啉初始浓度为20 mg·L~(-1),催化剂投加量为0.5 g·L~(-1),H_2O_2投加量为20 mmol·L~(-1),p H=6.3时,该催化剂对喹啉有很好的矿化效果(TOC去除率为3%).催化剂重复使用性能稳定,重复使用5次喹啉去除率仍高达99%,但TOC去除率略有降低,铁溶出率为0.48%以下.     

废水中十六烷基三甲基溴化铵的光降解动力学研究

季铵盐类阳离子表面活性剂污染会对水生环境产生不利影响,研究了在紫外灯下以Fe3+为单一催化剂降解水体中阳离子表面活性剂十六烷基三甲基溴化铵(CTAB)的降解动力学规律.实验通过测定光降解过程中CTAB质量浓度的变化,研究了Fe3+质量浓度、溶液pH对CTAB降解的影响.初步测定了降解产物,探讨了降解机理.结果表明,CTAB光降解反应符合一级反应动力学规律,在溶液pH值为2.00～3.00时,一级动力学反应常数k受pH值、Fe3+质量浓度等影响,在0.032～0.180min-1之间变化,降解产物主要有HCOOH、CO2、NO-2等,当CTAB初始质量浓度为40 mg·L-1时TOC去除率在3 h达到32%.研究表明UV/Fe3+法可快速有效去除废水中季铵盐类表面活性剂污染物.     

超声波/Fenton试剂联用降解水中的吡啶

采用超声波/Fenton联用技术降解水中的吡啶,探讨了吡啶初始浓度、反应温度、pH值、H2O2浓度、超声波声能密度和超声波频率对降解效果的影响及规律,实验发现,在所研究的吡啶初始浓度范围内,随着吡啶初始浓度的增大,其降解率减小;同时,随着反应温度、pH值、H2O2浓度和超声波声能密度的增大,吡啶的降解率增大;对于24.55kHz和30.19kHz两种频率而言,超声波频率愈高吡啶的去除率愈大,而对于30.19kHz和34.19kHz两种频率而言,吡啶去除率随频率的变化关系不明显,超声波和Fenton联用对吡啶进行降解比二者单独降解吡啶有更好的处理效果,另外,对于不同初始浓度的吡啶溶液来说,在所研究的浓度范围内,超声波/Fenton试剂联用降解吡啶的反应属于一级动力学反应,     

吸附模式对有机物光催化降解的影响3.MEA-Langmuir-Hinshelwood光催化降解动力学方程

传统的Langmuir-Hinshelwood方程式不能定性、定量地解释H-酸在TiO2表面的吸附平衡常数KL与其在TiO2悬浮液中的光催化降解速率r之间的关系.这是因为在实际测定中,吸附平衡常数KL一般是通过给定有机物的平衡吸附量和平衡浓度而求得的.这样的KL不能表达给定有机物不同吸附模式吸附力的差别.因而以往的理论方法不能描述吸附力对光催化降解动力学的影响,而只能描述吸附量对r的影响.亚稳平衡态吸附(MEA)理论认为,同一吸附质在相同的热力学条件下可以不同的MEA态(包括同一溶质的不同吸附构型/模式)达到实际的吸附终态.从MEA的概念对Langmuir-Hinshelwood模型进行半经验性修正,可以较好地描述吸附量和吸附力(吸附模式)共同对H-酸在TiO2悬浮液中光催化降解动力学的影响.     

吸附模式对有机物光催化降解的影响2.H-酸在TiO2表面的光催化降解途径

水溶液中H-酸通过磺酸基团吸附在TiO2表面,UV照射TiO2所产生的自由基首先进攻吸附在TiO2表面的磺酸基团,从而进一步导致萘环开环.pH 2.5条件下,虽然饱和吸附量较大,但由于H-酸仅通过一个磺酸基团吸附在TiO2表面,过程中产生的硫酸根速率较慢,最终的光降解速率也较慢.pH 5.0条件下,虽然饱和吸附量较小,但由于吸附在TiO2表面的两个磺酸基团同时受到来自TiO2表面自由基的进攻,过程中产生的硫酸根速率较快,最终的光降解速率也较快.吸附模式的差异是导致H-酸在不同pH值条件下光催化降解途径和速率差异的关键因素.     

水热法制备PbMoO4微晶体及其光催化降解灭幼脲

以水热法合成的PbMoO4微晶体为催化剂,考察了反应溶液pH、污染物初始浓度和催化剂用量对光催化降解灭幼脲的影响,研究了光催化降解过程的反应动力学和作用机理.结果表明,最佳反应溶液pH 6.0、污染物初始浓度20 mg.L-1、催化剂用量0.4 g.L-1.反应4 h灭幼脲降解率达99.96%,矿化率达66.4%,降解反应符合一级动力学.通过加入自由基清除剂对比实验发现,PbMoO4微晶体主要通过空穴和.OH的氧化作用使灭幼脲降解,其中空穴起主要作用.     

Removal of decabromodiphenyl ether (BDE-209) by sepiolite-supported nanoscale zerovalent iron

Nanoscale zerovalent iron (nZVI) synthesized using sepiolite as a supporter was used to investigate the removal kinetics and mechanisms of decabromodiphenyl ether (BDE-209). BDE-209 was rapidly removed by the prepared sepiolite-supported nZVI with a reaction rate that was 5 times greater than that of the conventionally prepared nZVI because of its high surface area and reactivity. The degradation of BDE-209 occurred in a stepwise debromination manner, which followed pseudo-first-order kinetics. The removal efficiency of BDE-209 increased with increasing dosage of sepiolite-supported nZVI particles and decreasing pH, and the efficiency decreased with increasing initial BDE-209 concentrations. The presence of tetrahydrofuran (THF) as a cosolvent at certain volume fractions in water influenced the degradation rate of sepiolite-supported nZVI. Debromination pathways of BDE-209 with sepiolite-supported nZVI were proposed based on the identified reaction intermediates, which ranged from nona- to mono-brominated diphenylethers (BDEs) under acidic conditions and nona- to penta-BDEs under alkaline conditions. Adsorption on sepiolite-supported nZVI particles also played a role in the removal of BDE-209. Our findings indicate that the particles have potential applications in removing environmental pollutants, such as halogenated organic contaminants.     

Kinetics of microwave-enhanced oxidation of phenol by hydrogen peroxide

Aqueous solutions of phenol were oxidized by hydrogen peroxide assisted by microwave (MW) irradiation. A simple kinetic model for the overall degradation of phenol in the presence of excess H₂O₂ is proposed in which the degradation rate of phenol is expressed as a linear function of the concentrations of phenol and H₂O₂. A detailed parametric study showed that the degradation rate of phenol increased with increasing [H₂O₂] until saturation was observed. Phenol degradation followed apparent zero-order kinetics under MW radiation or H₂O₂ oxidation. However, after 90 min of irradiation, the observed kinetics shifted to pseudo first order. The overall reaction rates were significantly enhanced in the combined MW/H₂O₂ system, mainly because microwave could accelerate H₂O₂ to generate hydroxyl radical (^·OH) and other reactive oxygen intermediates. The observed synergetic effects of the MW/H₂O₂ process resulted in an increased in the net reaction rate by a factor of 5.75. When hydrogen peroxide is present in a large stoichiometric excess, the time required to achieve complete mineralization is reduced significantly.     

部分水溶性偶氮染料的光催化降解研究

本研究以高压汞灯为光源,系统地研究了１６种偶氮染料在水溶液中的ＴｉＯ２光催化降解。结果表明,这些偶氮染料的光解为一级动力学反应,采用ＴｉＯ２光催化降解方法处理所研究的偶氮染料是可行的,并初步探讨了染料的结构与光解反应表观速率常数之间的关系。     

Factors influencing the photodegradation of N-nitrosodimethylamine in drinking water

In order to provide basic data for practical application, photodegradation experiment of N-nitrosodimethylamine (NDMA) in aqueous solution was carried out with a low-pressure Hg lamp. Effects of the initial concentration of NDMA, solution pH, dissolved oxygen, and the presence of humic acid on NDMA photodegradation were investigated. NDMA at various initial concentrations selected in this study was almost completely photodegraded by UV irradiation within 20 min, except that at 1.07 mmol/L, NDMA could be photodegraded almost completely in the acidic and neutral solutions, while the removal efficiency decreased remarkably in the alkaline solution. Dissolved oxygen enhanced the NDMA photodegradation, and the presence of humic acid inhibited the degradation of NDMA. Depending on the initial concentration of NDMA, NDMA photodegradation by UV obeyed the pseudo-first-order kinetics. Dimethylamine, nitrite, and nitrate were detected as the photodegradation products of NDMA. ¹O₂ was found to be the reactive oxygen species present in the NDMA photodegradation process by UV, based on the inhibiting experiments using tert-butanol and sodium azide.     

Photoinduced degradation of sulfonamides,kinetic, and structural characterization of transformation products and assessment of environmental toxicity

This study focuses on the degradation of the sulfonamide antibiotics, sulfadiazine, sulfamethazine, sulfamethoxazole, and sulfathiazole, using ultraviolet irradiation in various conditions. Different pHs were investigated in combination with the addition of hydrogen peroxide and further oxygen removal. High-performance liquid chromatography electrospray ionization ion-trap mass spectrometry was used to identify and elucidate degradation products and to establish concentration–time curves. Previously unknown degradation products could be characterized. Reaction rate constants of all compounds and transformation products were determined. The parent sulfonamides decayed according to first-order kinetics, while the concentrations of the transformation products varied with time according to a subsequent reaction of an intermediate product. Quantum efficiencies were analyzed for mechanistic purposes. As example, sulfamethoxazole was added to effluents from a wastewater treatment plant and irradiated. Phototoxicity and environmental hazard were assessed through quantitative structure-activity relationship computations. In addition, the minimal inhibition concentrations were determined for Pseudomonas fluorescens and Bacillus subtilis. Conclusions for UV-C irradiation as a fourth purification wastewater treatment stage were derived.     

一级动力学反应方程参数估计中若干问题的讨论

在农药的环境行为研究中，常用一级动力学反应方程来模拟农药的降解或残留。本文论述了用线性回归分析法估计一级化学动力学方程参数时存在的初始浓度飘移和非本义最优化问题，讨论了与此相关联的试验设置、安全间隔期、分段模拟和试验数据处理等问题，提出了解决问题的初步设想。     

活性艳红X-3B的厌氧生物降解与机理

以活性艳红X-3B(RBR)为研究对象,分3个不同浓度组研究其在厌氧颗粒污泥作用下的降解性能,并采用生物降解动力学方程拟合其降解过程,同时利用GC-MS分析RBR的生物降解途径.试验结果表明,RBR在厌氧颗粒污泥中降解性能很好,去除率可达93.67%,且其降解过程符合二级反应动力学,其半衰期约为3.561 h.从GC-MS和UV-可见光谱的分析得出,RBR在厌氧颗粒污泥的作用下偶氮键断裂,且生成的芳香胺类化合物进一步降解为小分子的烃类、酚类、醇类和脂类化合物.