Hydrophobic organic compound partitioning from bulk water to the water/air interface

Partitioning of hydrophobic organic compounds to the interface between water and air may significantly affect the distribution and transfer of many xenobiotic chemicals between vapor and aqueous phases. The fluorescent probe, 1-methylperylene, was used to investigate the affinity of hydrophobic compounds for the water–air interface by varying the ratio of interfacial surface area to water volume in a fused-quartz cuvette. We found that the water–air/water interface partitioning coefficient [K_w−awi=1.2 mol cm^-2_awi/(mol ml^-1_w)] for this polycyclic aromatic hydrocarbon (PAH) was quantitatively consistent with partitioning to the same interface but from the airside, recently reported in the literature for less hydrophobic PAHs. Our results demonstrate significant partitioning from bulk water to the water/air interface for a hydrophobicity range relevant to many xenobiotic compounds. Anticipated implications of this process for the environmental chemistry of hydrophobic compounds include retarded gas-phase transport in unsaturated soils, bubble-mediated transport in water, droplet-mediated transport in the atmosphere, and photochemical reactions.     

Sorption of perfluoroalkyl substances in sewage sludge

The sorption behaviour of three perfluoroalkyl substances (PFASs) (perfluorooctanesulfonic acid (PFOS), perfluorooctanoic acid (PFOA) and perfluorobutanesulfonic acid (PFBS)) was studied in sewage sludge samples. Sorption isotherms were obtained by varying initial concentrations of PFOS, PFOA and PFBS. The maximum values of the sorption solid–liquid distribution coefficients (K_d,max) varied by almost two orders of magnitude among the target PFASs: 140–281 mL g^?1 for PFOS, 30–54 mL g^?1 for PFOA and 9–18 mL g^?1 for PFBS. Freundlich and linear fittings were appropriate for describing the sorption behaviour of PFASs in the sludge samples, and the derived K_F and K_d,linear parameters correlated well. The hydrophobicity of the PFASs was the key parameter that influenced their sorption in sewage sludge. Sorption parameters and log(K_OW) were correlated, and for PFOS (the most hydrophobic compound), pH and Ca?+?Mg status of the sludge controlled the variation in the sorption parameter values. Sorption reversibility was also tested from desorption isotherms, which were also linear. Desorption parameters were systematically higher than the corresponding sorption parameters (up to sixfold higher), thus indicating a significant degree of irreversible sorption, which decreased in the sequence PFOS?>?PFOA?>?PFBS.     

Sorptive Behavior of Sorgoleone in Ultisol in Two Solvent Systems and Determination of Its Lipophilicity

Sorgoleone (SGL) exuded by sorghum roots inhibits the development of some weeds. Due to its high hydrophobicity, it is expected that SGL presents low soil mobility and limited allelopathic activity in the field. This work aims to evaluate the sorptivity of sorgoleone in octanol-water and in soil under two solvent systems. The two solvent systems were methanol:water (60:40) (MeOH:H₂O) and pure methanol (MeOH). These two solvent systems promote different conditions for SGL solubility. Treatments were arranged in a 2 × 6 factorial (solvent systems × equilibrium concentrations in the solution (EC)). For each solvent, the sorption was achieved by shaking 500 mg of soil with 10 ml of 0, 5, 10, 15, 25, 40, and 60 mg L^?1 of SGL solution, during 24 h. After centrifugation, the supernatant was filtered and the SGL concentration was determined by high performance liquid chromatography (HPLC). Data of sorbed amount of SGL were submitted to variance analysis, using a hierarchic factorial model. The data of sorbed amount (x/m) and equilibrium concentration (C) were fitted to the linear (x/m = a + K _d C) and to the Freundlich (x/m = K _f C ^1/n ) models. The isotherm obtained for the MeOH:H₂O system presented linear shape, whereas for the MeOH system a two subsequent linear isotherm was fitted. Sorgoleone is a highly hydrophobic compound, presenting a log K _ow of 6.1. The sorption of sorgoleone to the soil was very high. The organic environment stimulated the sorgoleone sorption to the soil.     

Solubility of organic acids in various methanol and salt concentrations: the implication on organic acid sorption in a cosolvent system

The well-known cosolvency-induced sorption model is not applicable to predict the sorption of carboxylic acids in cosolvent system. To investigate the phenomenon, sorption and solubility of chlorinated phenols (2,4-dichlorophenol (2,4-DCP) and 2,4,6-trichlorophenol (2,4,6-TCP)) and carboxylic acids (benzoic acid and 2,4-dichlorophenoxyacetic acid (2,4-D)) were measured in soil-methanol mixture with various ionic strengths. The sorption (K_m) of chlorinated phenols was explained by a cosolvency-induced sorption model; the inverse log-linear relationship between the K_m and methanol volume fraction (f_c). However, the K_m of carboxylic acids increased with increasing f_c. This discrepancy was attributed to the effect of the carboxylic moiety. To explain the effect, solubility was measured for benzoic acid and 2,4,6-TCP from various liquid conditions. For both solutes, the cosolvency power (σ) increased with CaCl₂ concentrations and the salting constant (K^s) became smaller as f_c increased. However, the σ value at a given salt concentration and the K^s value at a given f_c were greater for 2,4,6-TCP than for benzoic acid, both of which were due to the greater hydrophobicity of the former. Overall, the solubility profiles of the both solutes on combination of f_c and CaCl₂ concentration evidenced no specific role of the carboxylic moiety. Therefore, it can be reasonably concluded that the positive relationship between K_m and f_c for carboxylic organic acid can be attributed to the modification of the activity coefficient occurred in the solid phase, which cannot be traceable by cosolvency-based model.     

Sorption of chlorinated solvents and degradation products on natural clayey tills

The sorption of chlorinated solvents and degradation products on seven natural clayey till samples from three contaminated sites was investigated by laboratory batch experiments in order to obtain reliable sorption coefficients (K_d values). The sorption isotherms for all compounds were nearly linear, but fitted by Freundlich isotherms slightly better over the entire concentration range. For chloroethylenes, tetrachloroethylene (PCE) was most strongly sorbed to the clayey till samples (K_d = 0.84-2.45 L kg⁻¹), followed by trichloroethylene (TCE, K_d = 0.62-0.96 L kg⁻¹), cis-dichloroethylene (cis-DCE, K_d = 0.17-0.82 L kg⁻¹) and vinyl chloride (VC, K_d = 0.12-0.36 L kg⁻¹). For chloroethanes, 1,1,1-trichloroethane (1,1,1-TCA) was most strongly sorbed (K_d = 0.2-0.45 L kg⁻¹), followed by 1,1-dichloroethane (1,1-DCA, K_d = 0.16-0.24 L kg⁻¹) and chloroethane (CA, K_d = 0.12-0.18 L kg⁻¹). This is consistent with the order of hydrophobicity of the compounds. The octanol-water coefficient (log K_ow) correlated slightly better with log K_d values than log K_oc values indicating that the K_d values may be independent of the actual organic carbon content (f_oc). The estimated log K_oc or log K_d for chlorinated solvents and degradation products determined by regression of data in this study were significantly higher than values determined by previously published empirical relationships. The site specific K_d values as well as the new empirical relationship compared well with calculations on water and soil core concentration for cis-DCE and VC from the Rugårdsvej site. In conclusion, this study with a wide range of chlorinated ethenes and ethanes - in line with previous studies on PCE and TCE - suggest that sorption in clayey tills could be higher than typically expected.     

Modifications of black carbons and their influence on pyrene sorption

Sorption of pyrene on black carbons (BCs) obtained by heating sawdust at two temperatures (400 and 700 °C, denoted as 400BC and 700BC, respectively), as well as on modified BCs (via oxidation, oximation, and hydrolysis) was studied to investigate the role of BC structural characteristics in sorption of hydrophobic organic compounds. Pyrene was bound strongly by 700BC and 400BC, with organic carbon normalized distribution coefficients (K_oc) of 10^5.04-10^5.86 and 10^4.65-10^5.16, respectively, at equilibrium pyrene concentrations of 10-100 μg L⁻¹. Both chemical composition and pore distribution of the two BCs changed after modifications, which led to changes in their sorption characteristics for pyrene. After modifications, the linearity of pyrene sorption isotherm increased for 700BC but decreased for 400BC. For 700BC, both oxidation and oximation reduced pyrene sorption, with K_oc decreasing by 69.1-73.7% and 18.7-33.9%, respectively, whereas hydrolysis did not exert a significant influence. For 400BC, oxidation and hydrolysis reduced K_oc by 2.28-25.9% and 29.2-33.9%, respectively, while oximation increased K_oc. In most cases, the change in sorption capacity could be explained by the changes in C content and type, polarity, surface area, and micropore volume of the BCs; however, the role of conformation (the accessibility to sorption sites) could not be ignored.     

Polar organic chemical integrative sampler (POCIS) uptake rates for 17 polar pesticides and degradation products: laboratory calibration

Polar organic chemical integrative samplers (POCIS) are useful for monitoring a wide range of chemicals, including polar pesticides, in water bodies. However, few calibration data are available, which limits the use of these samplers for time-weighted average concentration measurements in an aquatic medium. This work deals with the laboratory calibration of the pharmaceutical configuration of a polar organic chemical integrative sampler (pharm-POCIS) for calculating the sampling rates of 17 polar pesticides (1.15?≤?logK _ow?≤?3.71) commonly found in water. The experiment, conducted for 21 days in a continuous water flow-through exposure system, showed an integrative accumulation of all studied pesticides for 15 days. Three compounds (metalaxyl, azoxystrobine, and terbuthylazine) remained integrative for the 21-day experiment. The sampling rates measured ranged from 67.9 to 279 mL?day^?1 and increased with the hydrophobicity of the pesticides until reaching a plateau where no significant variation in sampling rate is observed when increasing the hydrophobicity.     

Toxicity of 58 substituted anilines and phenols to algae Pseudokirchneriella subcapitata and bacteria Vibrio fischeri: comparison with published data and QSARs

A congeneric set of 58 substituted anilines and phenols was tested using the 72-h algal growth inhibition assay with Pseudokirchneriella subcapitata and 15-min Vibrio fischeri luminescence inhibition assay. The set contained molecules substituted with one, two or three groups chosen from -chloro, -methyl or -ethyl. For 48 compounds there was no REACH-compatible algal toxicity data available before. The experimentally obtained EC50 values (mg L⁻¹) for algae ranged from 1.43 (3,4,5-trichloroaniline) to 197 (phenol) and for V. fischeri from 0.37 (2,3,5-trichlorophenol) to 491 (aniline). Only five of the tested 58 chemicals showed inhibitory effect to algae at concentrations >100 mg L⁻¹, i.e. could be classified as “not harmful”, 32 chemicals as “harmful” (10-100 mg L⁻¹) and 21 as “toxic” (1-10 mg L⁻¹). The occupied para-position tended to increase toxicity whereas most of the ortho-substituted congeners were the least toxic. As a rule, the higher the number of substituents the higher the hydrophobicity and toxicity. However, in case of both assays, the compounds of similar hydrophobicity showed up to 30-fold different toxicities. There were also assay/organism dependent tendencies: phenols were more toxic than anilines in the V. fischeri assay but not in the algal test. The comparison of the experimental toxicity data to the data available from the literature as well as to QSAR predictions showed that toxicity of phenols to algae can be modeled based on hydrophobicity, whereas the toxicity of anilines to algae as well as toxicity of both anilines and phenols to V. fischeri depended on other characteristics in addition to logK_ow.     

Experimental Variability in Characterization of Cyfluthrin Sorption to Soil

To assess the risk of a pesticide to leach to groundwater or to run off to surface water after application, it is necessary to characterize the sorption of the pesticide to soil. For pyrethroids, their hydrophobicity, strong sorption to various materials, and low solubility make it difficult to accurately characterize sorption processes. The objective of this research was to evaluate the variability in cyfluthrin ((RS)-α -cyano-4-fluoro-3-phenoxybenzyl (1RS,3RS;1RS,3SR)-3-(2,2-dichlorovinyl)-2,2-dimethylcyclopropanecarboxylate) sorption to soil as affected by experiment conditions. To minimize cyfluthrin sorption on the walls of glass, silanized-glass, stainless steel, and PTFE centrifuge tubes, cyfluthrin solution was added to aqueous soil slurries or directly to soil, after which it was equilibrated with aqueous solution. Depending on the soil, variation in sorption coefficients, K _oc, obtained using different experimental methodologies with one soil can be comparable to the variation in K _oc values obtained for soils with different physical and chemical properties using one method. K _oc values for cyfluthrin ranged from 56,000 to 300,000 L kg^?1. Sorption methodology needs to be evaluated before sorption coefficients are used in predictive transport models.     

Surfactant solubilization of hydrophobic compounds in soil and water

The soil/water partition coefficient (K_d) of hexachlorobenzene (HCB) ranged from 220 1/kg to 1800 1/kg for eight soils having a wide range of physico-chemical properties. K_d normalised to soil organic carbon (K_oc) was found to be 28000 ± 4800 1/kg. Anionic surfactant dodecylsulphate (DS) present at concentrations above the critical micellar concentration (CMC) caused reductions in the apparent soil/water partition coefficient (K_d ^*) in the range of 3–26 times for most soils and up to 36–91 times for sandy soils. Below CMC, at environmentally relevant surfactant concentrations, K_d ^* was reduced by a factor of 1–13. For clay and calcareous soils significant adsorption/complexation/precipitation of DS occurred. At the lowest DS concentration this produced a two-fold increase in K_d ^*. At increasing DS concentrations this effect was shielded by the solubihzing effect from DS. Monomer (K_mn) and micellar (K_mc) surfactant/water partition coefficients for HCB were determined to be, 980 ± 190 1/kg and 21000 ± 1600 1/kg, respectively.     

Respiratory uptake kinetics of neutral hydrophobic organic chemicals in a marine benthic fish, Pseudopleuronectes yokohamae

We investigated the respiratory uptake kinetics of polychlorinated biphenyls (PCBs), organohalogen pesticides (OCPs), polycyclic aromatic hydrocarbons (PAHs), and 2,2′,4,4′-tetrabrominated diphenyl ether (BDE #47) in a marine benthic fish, Pseudopleuronectes yokohamae. The respiratory uptake efficiencies (E_W) of the chemicals, of which there have been no reports for the majority of persistent organic pollutants (POPs), were obtained by measuring the respiratory uptake rate constants (k₁) and the oxygen consumption rates of fish. Fish were exposed to water in which these chemicals were dissolved at environmentally relevant concentrations for 28 d, followed by 168 d of depuration in clean seawater. The k₁ and E_W values for 99 compounds were obtained, and they ranged from 2000 to 42 000 L kg-lipid⁻¹ d⁻¹ and from 0.060 to 1.3, respectively. The E_W values of the chemicals, except for PAHs, tended to increase with increasing values of the log octanol–water partition coefficients (K_OW) of the chemicals up to a log K_OW of 5. For log K_OW in the range 3–5, the E_W values in this study were much lower than those in a published study (about one-third). As a result of analysis by a two-phase resistance model, the resistance of transport rates to the lipid phase in this study was lower than was the case in the published study. These findings indicate that the E_W predicted by the published study for log K_OW in the range 3–5 may differ among fish species and water temperature, and further study is needed.     

Chlorothalonil binding to aquatic humic substances assessed from gas purge studies

Abstract

Fate of the fungicide chlorothalonil (TCIN) binding to dissolved organic acid fractions was quantified using gas‐purge desorption studies. Binding studies were conducted to measure the dissolved organic carbon partition constant (K_DOC) with aquatic fulvic and humic acid fractions purified from cranberry bog water. Desorption studies at DOC concentrations up to 50 mg L^‐1 resulted in mean log K_DOC values of 4.63 (s.d.=0.5, n=8) and 4.81 (s.d.=0.7, n=7) for fulvic and humic acids, respectively. These values deviated from reported K_OC (organic carbon) values by 0.5 to 1.5 orders of magnitude. The relationship between K_OC and K_DOC did not conform to accepted ratios of 10: 1 to 3: 1, although these studies were conducted with the strong hydrophobic fraction of DOC. Binding was rapid suggesting hydrophobic partitioning or weak Van Der Waals forces as binding mechanisms. The strong binding potential for TCIN to aquatic humic substances corresponds to increased solubility in the aqueous system. Sorption to DOC suggests a possible transport mechanism which may result in elevated concentrations of TCIN in cranberry bog systems.     

Uptake rate constants and partition coefficients for vapor phase organic chemicals using semipermeable membrane devices (SPMDs)

To fully utilize semipermeable membrane devices (SPMDs) as passive samplers in air monitoring, data are required to accurately estimate airborne concentrations of environmental contaminants. Limited uptake rate constants (k_ua) and no SPMD air partitioning coefficient (K_sa) existed for vapor-phase contaminants. This research was conducted to expand the existing body of kinetic data for SPMD air sampling by determining k_ua and K_sa for a number of airborne contaminants including the chemical classes: polycyclic aromatic hydrocarbons, organochlorine pesticides, brominated diphenyl ethers, phthalate esters, synthetic pyrethroids, and organophosphate/organosulfur pesticides. The k_uas were obtained for 48 of 50 chemicals investigated and ranged from 0.03 to 3.07 m³ g^?1 d^?1. In cases where uptake was approaching equilibrium, K_sas were approximated. K_sa values (no units) were determined or estimated for 48 of the chemicals investigated and ranging from 3.84E+5 to 7.34E+7. This research utilized a test system (United States Patent 6,877,724 B1) which afforded the capability to generate and maintain constant concentrations of vapor-phase chemical mixtures. The test system and experimental design employed gave reproducible results during experimental runs spanning more than two years. This reproducibility was shown by obtaining mean k_ua values (n = 3) of anthracene and p,p′-DDE at 0.96 and 1.57 m³ g^?1 d^?1 with relative standard deviations of 8.4% and 8.6% respectively.     

Distribution Equilibrium of Mercury (II) Chloride between Water and Air Applied to Flue Gas Scrubbing

ABSTRACT

In the literature, different values of the distribution coefficient K_H for HgCl₂ between water and air are present in a range that spans more than 3 orders of magnitude. In order to determine if a waste incineration scrubber solution could become saturated with regard to HgCl₂, an accurate experimental determination of the distribution constant of HgCl₂ at elevated temperatures is needed. In this work, the coefficient has been determined at four different temperatures between 10 and 50 °C. The Arrhenius expression obtained is 5.5 x 10⁵ x exp[-(8060 ± 2200)/7] with a corresponding enthalpy for the process HgCl₂(aq)<» HgCl₂(g) of 67 ± 20 kJ/mole. K_H at 293 K was found to be ~5 x 10^-7 atm M^-1, which is in almost perfect agreement with an earlier study. Applying the obtained K_H values to waste incineration scrubber conditions shows that no major saturation effect will occur.     

Behaviour of pharmaceuticals in spiked lake sediments - effects and interactions with benthic invertebrates

The behaviour and effects of atorvastatin (ATO), carbamazepine (CBZ), and 17α-ethinylestradiol (EE2) were investigated in spiked lake sediments, at concentrations up to 56.5 mg kg⁻¹ dry weight (dw), with the benthic invertebrates Chironomus dilutus and Hyalella azteca. Desorption constants were calculated in the presence and absence of animals, using linear isotherms, yielding K_d values of 28.2, 189.0 and 125.1 L kg⁻¹ (ATO), 73.7, 201.7 and 263.2 L kg⁻¹ (CBZ), and 114.9, 114.2 and 519.2 L kg⁻¹ (EE2) for C. dilutus, H. azteca, and without animals, respectively. For ATO and CBZ, K_d values were smaller in the presence of C. dilutus, indicating greater desorption to the overlying water from bioturbation, which is consistent with the predominantly benthic occurrence of C. dilutus compared to H. azteca. In contrast, due to its greater hydrophobicity, bioturbation did not significantly affect desorption of EE2. No significant toxicity was observed, indicating decreased bioavailability of the chemicals sorbed to sediments compared with water-only toxicity assays.     

Effects of black carbon on bioturbation-induced benthic fluxes of polychlorinated biphenyls

It is unknown whether carbonaceous geosorbents, such as black carbon (BC) affect bioturbation by benthic invertebrates, thereby possibly affecting sediment-water exchange of sediment-bound contaminants. Here, we assess the effects of oil soot on polychlorinated biphenyl (PCB) mass transfer from sediment to overlying water, for sediments with and without tubificid oligochaeta as bioturbators. PCB levels were so low that toxicity to the oligochaeta played no role, whereas soot levels and binding affinity of PCBs to soot were so low that pore water PCB concentrations were not significantly affected by binding of PCBs to soot. This setup left direct effects of BC on bioturbation activity as the only explanation for any observed effects on mass transfer. Mass transfer coefficients (K_L) for benthic boundary layer transport were measured by a novel flux method using Empore™ disks as a sink for PCBs in the overlying water. For the PCBs studied (logK_ow 5.2-8.2), K_L values ranged from 0.2 to 2 cm × d⁻¹ in systems without tubificids. Systems with tubificids showed K_L values that were a factor of 10-25 higher. However, in the presence of oil soot, tubificids did not cause an increase in mass transfer coefficients. This suggests that at BC levels as encountered under field conditions, the mechanism for reduction of sediment-water transfer of contaminants may be twofold: (a) reduced mass transfer due to strong binding of the contaminants to BC, and (b) reduced mass transfer of contaminants due to a decrease in bioturbation activity.     

Sorption of polar and nonpolar organic contaminants by oil-contaminated soil

Sorption of nonpolar (phenanthrene and butylate) and polar (atrazine and diuron) organic chemicals to oil-contaminated soil was examined to investigate oil effects on sorption of organic chemicals and to derive oil–water distribution coefficients (K_oil). The resulting oil-contaminated soil–water distribution coefficients (K_d) for phenanthrene demonstrated sorption-enhancing effects at both lower and higher oil concentrations (C_oil) but sorption-reducing (competitive) effects at intermediate C_oil (approximately 1 g kg⁻¹). Rationalization of the different dominant effects was attempted in terms of the relative aliphatic carbon content which determines the accessibility of the aromatic cores to phenanthrene. Little or no competitive effect occurred for butylate because its sorption was dominated by partitioning. For atrazine and diuron, the changes in K_d at C_oil above approximately 1 g kg⁻¹ were negligible, indicating that the presently investigated oil has little or no effect on the two tested compounds even though the polarity of the oil is much less than soil organic matter (SOM). Therefore, specific interactions with the active groups (aromatic and polar domains) are dominantly responsible for the sorption of polar sorbates, and thus their sorption is controlled by available sorption sites. This study showed that the oil has the potential to be a dominant sorptive phase for nonpolar pollutants when compared to SOM, but hardly so for polar compounds. The results may aid in a better understanding of the role of the aliphatic and aromatic domains in sorption of nonpolar and polar organic pollutants.     

Acetamiprid,carbendazim, diuron and thiamethoxam sorption in two Brazilian tropical soils

Sorption of acetamiprid ((E)-N1-[(6-chloro-3-pyridyl)methyl]-N2-cyano-N1-methylacetamidine), carbendazim (methyl benzimidazol-2-ylcarbamate), diuron (N-(3,4-dichlorophenyl)-N, N-dimethyl urea) and thiamethoxam (3-(2-chloro-thiazol-5-ylmethyl)-5-methyl-[1,3,5]oxadiazinan-4-ylidene-N-nitroamine) was evaluated in two Brazilian tropical soils, Oxisol and Entisol, from Primavera do Leste region, Mato Grosso State, Brazil. To describe the sorption process, batch experiments were carried out. Linear and Freundlich isotherm models were used to calculate the K _d and K _f coefficients from experimental data. The K _d values were utilized to calculate the partition coefficient normalized to soil organic carbon (K _oc ). For the pesticides acetamiprid, carbendazim, diuron and thiamenthoxan the K _oc (mL g^{? 1}) values ranged in both soils from 98 – 3235, 1024 – 2644, 145 – 2631 and 104 – 2877, respectively. From the studied pesticides, only carbendazim presented correlation (r² = 0.82 and p < 0.01) with soil organic carbon (OC) content. Acetamiprid and thiamethoxam showed low sorption coefficients, representing a high risk of surface and ground water contamination.     

Structure-related distribution of PCDD/Fs, PCBs and HCB in a river-sea system

Water concentrations of PCDD/Fs, HCB, and non-ortho, mono-ortho, and non-dioxin-like PCBs were measured four times during 1 year in a coastal area of the Baltic Sea, to investigate background levels and distribution behaviour. Sampling sites included two rivers, an estuary, and the sea. Particulate and apparently dissolved concentrations were determined using active sampling (filters + PUFs), while freely dissolved concentrations were determined using passive sampling (POM-samplers). The distribution between particulate + colloidal and freely dissolved phases, in the form of TOC-normalized distribution ratios (K_TOC), was found to be near or at equilibrium. The observed K_TOC were not significantly different between sampling sites or seasons. For PCDD/Fs, the concentrations were significantly correlated to suspended particulate matter (SPM), while no correlation to organic carbon (TOC) was observed. In the estuary and the sea, PCB concentrations were correlated to TOC. The sorption of various congeners to SPM and TOC appeared to be related to both hydrophobicity and 3D-structure. The PCDD/F concentration in the sea decreased to one third in May, likely connected to the increased vertical flux of particles during the spring bloom.