Laboratory analog and numerical study of groundwater flow and solute transport in a karst aquifer with conduit and matrix domains

New mathematical and laboratory methods have been developed for simulating groundwater flow and solute transport in karst aquifers having conduits imbedded in a porous medium, such as limestone. The Stokes equations are used to model the flow in the conduits and the Darcy equation is used for the flow in the matrix. The Beavers–Joseph interface boundary conditions are adopted to describe the flow exchange at the interface boundary between the two domains. A laboratory analog is used to simulate the conduit and matrix domains of a karst aquifer. The conduit domain is located at the bottom of the transparent plexiglas laboratory analog and glass beads occupy the remaining space to represent the matrix domain. Water flows into and out of the two domains separately and each has its own supply and outflow reservoirs. Water and solute are exchanged through an interface between the two domains. Pressure transducers located within the matrix and conduit domains of the analog provide data that is processed and stored in digital format. Dye tracing experiments are recorded using time-lapse imaging. The data and images produced are analyzed by a spatial analysis program. The experiments provide not only hydraulic head distribution but also capture solute front images and mass exchange measurements between the conduit and matrix domains. In the experiment, we measure and record pressures, and quantify flow rates and solute transport. The results present a plausible argument that laboratory analogs can characterize groundwater water flow, solute transport, and mass exchange between the conduit and matrix domains in a karst aquifer. The analog validates the predictions of a numerical model and demonstrates the need of laboratory analogs to provide verification of proposed theories and the calibration of mathematical models.     

3-D numerical evaluation of density effects on tracer tests

In this paper we present numerical simulations carried out to assess the importance of density-dependent flow on tracer plume development. The scenario considered in the study is characterized by a short-term tracer injection phase into a fully penetrating well and a natural hydraulic gradient. The scenario is thought to be typical for tracer tests conducted in the field. Using a reference case as a starting point, different model parameters were changed in order to determine their importance to density effects. The study is based on a three-dimensional model domain. Results were interpreted using concentration contours and a first moment analysis. Tracer injections of 0.036 kg per meter of saturated aquifer thickness do not cause significant density effects assuming hydraulic gradients of at least 0.1%. Higher tracer input masses, as used for geoelectrical investigations, may lead to buoyancy-induced flow in the early phase of a tracer test which in turn impacts further plume development. This also holds true for shallow aquifers. Results of simulations with different tracer injection rates and durations imply that the tracer input scenario has a negligible effect on density flow. Employing model cases with different realizations of a log conductivity random field, it could be shown that small variations of hydraulic conductivity in the vicinity of the tracer injection well have a major control on the local tracer distribution but do not mask effects of buoyancy-induced flow.     

3-D numerical evaluation of density effects on tracer tests

In this paper we present numerical simulations carried out to assess the importance of density-dependent flow on tracer plume development. The scenario considered in the study is characterized by a short-term tracer injection phase into a fully penetrating well and a natural hydraulic gradient. The scenario is thought to be typical for tracer tests conducted in the field. Using a reference case as a starting point, different model parameters were changed in order to determine their importance to density effects. The study is based on a three-dimensional model domain. Results were interpreted using concentration contours and a first moment analysis. Tracer injections of 0.036 kg per meter of saturated aquifer thickness do not cause significant density effects assuming hydraulic gradients of at least 0.1%. Higher tracer input masses, as used for geoelectrical investigations, may lead to buoyancy-induced flow in the early phase of a tracer test which in turn impacts further plume development. This also holds true for shallow aquifers. Results of simulations with different tracer injection rates and durations imply that the tracer input scenario has a negligible effect on density flow. Employing model cases with different realizations of a log conductivity random field, it could be shown that small variations of hydraulic conductivity in the vicinity of the tracer injection well have a major control on the local tracer distribution but do not mask effects of buoyancy-induced flow.     

Modeling field-scale multiple tracer injection at a low-level waste disposal site in fractured rocks: effect of multiscale heterogeneity and source term uncertainty on conceptual understanding of mass transfer processes

Multiple factors may affect the scale-up of laboratory multi-tracer injection into structured porous media to the field. Under transient flow conditions and with multiscale heterogeneities in the field, previous attempts to scale-up laboratory experiments have not answered definitely the questions about the governing mechanisms and the spatial extent of the influence of small-scale mass transfer processes such as matrix diffusion. The objective of this research is to investigate the effects of multiscale heterogeneity, mechanistic and site model conceptualization, and source term density effect on elucidating and interpreting tracer movement in the field. Tracer release and monitoring information previously obtained in a field campaign of multiple, conservative tracer injection under natural hydraulic gradients at a low-level waste disposal site in eastern Tennessee, United States, is used for the research. A suite of two-pore-domain, or fracture-matrix, groundwater flow and transport models are calibrated and used to conduct model parameter and prediction uncertainty analyses. These efforts are facilitated by a novel nested Latin-hypercube sampling technique. Our results verify, at field scale, a multiple-pore-domain, multiscale mechanistic conceptual model that was used previously to interpret only laboratory observations. The results also suggest that, integrated over the entire field site, mass flux rates attributable to small-scale mass transfer are comparable to that of field-scale solute transport. The uncertainty analyses show that fracture spacing is the most important model parameter and model prediction uncertainty is relatively higher at the interface between the preferred flow path and its parent bedrock. The comparisons of site conceptual models indicate that the effect of matrix diffusion may be confined to the immediate neighborhood of the preferential flow path. Finally, because the relatively large amount of tracer needed for field studies, it is likely that source term density effect may exaggerate or obscure the effect of matrix diffusion on the movement of tracers from the preferred flow path into the bedrock.     

Transport of coliphage PRD1 in a surface flow constructed wetland.

A tracer study was conducted in a 3-ha surface flow constructed wetland to analyze transport performance of PRD1, an enteric virus model. The convection-dispersion equation (CDE), including a first-order reaction model, adequately simulated transport performance of PRD1 in the wetland under an average hydraulic loading rate of 82 mm/d. Convective velocity (v) and longitudinal dispersion coefficient (D) were estimated by modeling a conservative tracer (bromide) pulse through the wetland. Both PRD1 and bromide were simultaneously added to the entering secondary treated wastewater effluent. The mass of bromide and PRD1 recovered was 76 and 16%, respectively. The PRD1 decay rate was calculated to be 0.3/day. The findings of this study suggest that the CDE model and analytical moment equations represent a suitable option to characterize virus transport performance in surface flow constructed wetlands.     

Macrodispersion by diverging radial flows in randomly heterogeneous porous media

Radial flow takes place in a heterogeneous porous formation where the transmissivity T is modelled as a stationary random space function (RSF). The steady flow is driven by a given rate, and the mean velocity is radial. A pulse-like of a tracer is injected in the porous formation, and the thin plume spreads due to the fluctuations of the velocity which results a RSF as well. Transport is characterized by the mean front, and by the second spatial moment of the plume. We are primarily interested in tracer macrodispersion modelling. With the neglect of pore-scale dispersion, macrodispersion coefficients are computed at the second order of approximation, without neglecting the head-gradient fluctuations. Although transport is non-ergodic at the source, it is shown that ergodicity is achieved at small distances from the source. This is due to the fact that close to the source local velocities are quite large, and therefore solute particles become uncorrelated very soon. Under ergodic conditions, we compare macrodispersion mechanism in radial flows with that occurring in mean uniform flows. At short distances the spreading effect is highly enhanced by the large variability of the flow field, whereas at large distances transport exhibits a lesser dispersion due to the reduction of velocities. This supports the explanation provided by Indelman and Dagan (1999) to justify why the macrodispersivity is found smaller than that pertaining to mean uniform flows. The model is tested against a tracer transport experiment (Fernàndez-Garcia et al., 2004) by comparing the theoretical and experimental breakthrough curves. The accordance with real data, that is achieved without any fitting to concentration values, strengthens the capability of the proposed model to grasp the main features of such an experiment, the approximations as well as experimental uncertainties notwithstanding.     

Characterization of flow and transport processes within the unsaturated zone of Yucca Mountain, Nevada, under current and future climates

This paper presents a large-scale modeling study characterizing fluid flow and tracer transport in the unsaturated zone of Yucca Mountain, Nevada, a potential repository site for storing high-level radioactive waste. The study has been conducted using a three-dimensional numerical model, which incorporates a wide variety of field data and takes into account the coupled processes of flow and transport in the highly heterogeneous, unsaturated fractured porous rock. The modeling approach is based on a dual-continuum formulation of coupled multiphase fluid and tracer transport through fractured porous rock. Various scenarios of current and future climate conditions and their effects on the unsaturated zone are evaluated to aid in the assessment of the proposed repository's system performance using different conceptual models. These models are calibrated against field-measured data. Model-predicted flow and transport processes under current and future climates are discussed.     

Fluorescent dye imaging of the volume sampled by single well forced-gradient tracer tests evaluated in a laboratory-scale aquifer physical model

This study presents a new method to visualise forced-gradient tracer tests in 2-D using a laboratory-scale aquifer physical model. Experiments were designed to investigate the volume of aquifer sampled in vertical dipole flow tracer tests (DFTT) and push-pull tests (PPT), using a miniature monitoring well and straddle packer arrangement equipped with solute injection and recovery chambers. These tests have previously been used to estimate bulk aquifer hydraulic and transport properties for the evaluation of natural attenuation and other remediation approaches. Experiments were performed in a silica glass bead-filled box, using a fluorescent tracer (fluorescein) to deduce conservative solute transport paths. Digital images of fluorescein transport were captured under ultraviolet light and processed to analyse tracer plume geometry and obtain point-concentration breakthrough histories. Inorganic anion mixtures were also used to obtain conventional tracer breakthrough histories. Concentration data from the conservative tracer breakthrough curves was compared with the digital images and a well characterised numerical model. The results show that the peak tracer breakthrough response in dipole flow tracer tests samples a zone of aquifer close to the well screen, while the sampling volume of push-pull tests is limited by the length of the straddle packers used. The effective sampling volume of these single well forced-gradient tests in isotropic conditions can be estimated with simple equations. The experimental approach offers the opportunity to evaluate under controlled conditions the theoretical basis, design and performance of DFTTs and PPTs in porous media in relation to measured flow and transport properties.     

Operator-splitting errors in coupled reactive transport codes for transient variably saturated flow and contaminant transport in layered soil profiles

One possible way of integrating subsurface flow and transport processes with (bio)geochemical reactions is to couple by means of an operator-splitting approach two completely separate codes, one for variably-saturated flow and solute transport and one for equilibrium and kinetic biogeochemical reactions. This paper evaluates the accuracy of the operator-splitting approach for multicomponent systems for typical soil environmental problems involving transient atmospheric boundary conditions (precipitation, evapotranspiration) and layered soil profiles. The recently developed HP1 code was used to solve the coupled transport and chemical equations. For steady-state flow conditions, the accuracy was found to be mainly a function of the adopted spatial discretization and to a lesser extent of the temporal discretization. For transient flow situations, the accuracy depended in a complex manner on grid discretization, time stepping and the main flow conditions (infiltration versus evaporation). Whereas a finer grid size reduced the numerical errors during steady-state flow or the main infiltration periods, the errors sometimes slightly increased (generally less than 50%) when a finer grid size was used during periods with a high evapotranspiration demand (leading to high pressure head gradients near the soil surface). This indicates that operator-splitting errors are most significant during periods with high evaporative boundary conditions. The operator-splitting errors could be decreased by constraining the time step using the performance index (the product of the grid Peclet and Courant numbers) during infiltration, or the maximum time step during evapotranspiration. Several test problems were used to provide guidance for optimal spatial and temporal discretization.     

Effects of biofilm growth on flow and transport through a glass parallel plate fracture

The effects of biofilm growth on flow and solute transport through a sandblasted glass parallel plate fracture was investigated. The fracture was inoculated using soil microorganisms. Glucose, oxygen and other nutrients were supplied to support growth. The biomass initially formed discrete clusters attached to the glass surfaces, but over time formed a continuous biofilm. From dye tracer tests conducted during biofilm growth, it was observed that channels and low-permeability zones dominated transport. The hydraulic conductivity of the fracture showed a sigmoidal decrease with time. The hydraulic conductivity was reduced by a factor of 0.033, from 18 to 0.6 cm/s, corresponding to a 72% decrease in the hydraulic aperture, from 500 to 140 microm. In contrast, the mass balance aperture, determined from fluoride tracer tests, remained relatively constant, indicating that the impact of biomass growth on effective fracture porosity was much less than the effect on hydraulic conductivity. Analyses of pre-biofilm tracer tests revealed that both Taylor dispersion and macrodispersion were influencing transport. During biofilm growth, only macrodispersion was dominant. The macrodispersion coefficient alpha(macro) was found to increase logarithmically with hydraulic conductivity reduction.     

Modelling of nonreactive tracer dipole tests in a shear zone at the Grimsel test site

The investigation of the migration of a high pH plume in a fractured shear zone is foreseen by a long-term experiment at the Grimsel rock laboratory. In order to characterise the initial conditions for the long-term experiment and to evaluate an optimal hydraulic in situ set-up, several dipole experiments with nonreacting tracers have been performed. The dipole experiments differ in geometry, pumping rates and orientation to the background water flow. Several single and double-porosity models have been applied to fit the results of these dipole tracer tests in order to extract values for some transport parameters and discriminate for certain transport processes. A two-dimensional porous medium approach was successfully used to fit tracer breakthrough curves measured for a dipole experiment. A model based on a one-dimensional dual porous medium approach was also successful, although the applied hydraulic dipole, with similar injection and extraction rates, suggests the existence of an extended two-dimensional flow field. For the two-dimensional porous medium approach, tracer breakthrough could only be fitted with a complex flow field geometry within the heterogeneous fractured shear zone. The heterogeneity was generated by heterogeneous porosity and hydraulic permeability distributions. Predictions for further dipole geometries and a sorbing tracer have been calculated by means of both models using the flow and transport parameters deduced from fits for a single dipole experiment. This allows for comparison with the measured breakthrough of sorbing tracers. The foreseen experiment with sorbing (radionuclide) tracers will help decide on the appropriate approach that should be used to describe such dipole experiments in this shear zone. Additionally, the migration and spreading of a solution with high pH has been calculated taking into account mineral dissolution and precipitation in a two-dimensional porous medium approach in order to estimate the amount and character of the mineral reactions induced by the interaction between the high pH solution and the rock.     

Simulation evaluation of the effects of non-uniform flow and degradation parameter uncertainty on subsurface-flow constructed wetland performance.

Although constructed wetland treatment systems have been used in a variety of applications, uncertainty in adequately determining flow conditions or hydraulic residence times ("hydraulic efficiencies") and degradation model parameters remains a problem with their design. Breakthrough or impulse-type tracer studies in constructed wetlands often result in residence-time distributions exhibiting long skewed "tails" suggesting multiple flow channels or perhaps unrealistically large dispersion factors. A fractional-flow analysis is developed here to quantify possible flow non-uniformity in a subsurface-flow constructed wetland and is then used to assess the effects of non-uniformity and degradation model parameter variability on constituent (for example, chemical oxygen demand) removal. A model application to tracer data developed previously demonstrates how flow non-uniformity alone can account for significant "tailing" and can be related to even moderate estimated dispersion numbers. From the analysis, it is evident that flow non-uniformity is of greater concern than decay parameter uncertainty, and that, from a constructed wetland design and operation perspective, every effort should be made to ensure relative flow uniformity across the constructed wetland.     

Field investigation into unsaturated flow and transport in a fault: model analyses

Results of a fault test performed in the unsaturated zone of Yucca Mountain, Nevada, were analyzed using a three-dimensional numerical model. The fault was explicitly represented as a discrete feature and the surrounding rock was treated as a dual-continuum (fracture-matrix) system. Model calibration against seepage and water-travel-velocity data suggests that lithophysal cavities connected to fractures can considerably enhance the effective fracture porosity and therefore retard water flow in fractures. Comparisons between simulation results and tracer concentration data also indicate that matrix diffusion is an important mechanism for solute transport in unsaturated fractured rock. We found that an increased fault-matrix and fracture-matrix interface areas were needed to match the observed tracer data, which is consistent with previous studies. The study results suggest that the current site-scale model for the unsaturated zone of Yucca Mountain may underestimate radionuclide transport time within the unsaturated zone, because an increased fracture-matrix interface area and the increased effective fracture porosity arising from lithophysal cavities are not considered in the current site-scale model.     

Applied tracer tests in fractured rock: Can we predict natural gradient solute transport more accurately than fracture and matrix parameters?

Applied tracer tests provide a means to estimate aquifer parameters in fractured rock. The traditional approach to analysing these tests has been using a single fracture model to find the parameter values that generate the best fit to the measured breakthrough curve. In many cases, the ultimate aim is to predict solute transport under the natural gradient. Usually, no confidence limits are placed on parameter values and the impact of parameter errors on predictions of solute transport is not discussed. The assumption inherent in this approach is that the parameters determined under forced conditions will enable prediction of solute transport under the natural gradient. This paper considers the parameter and prediction uncertainty that might arise from analysis of breakthrough curves obtained from forced gradient applied tracer tests. By adding noise to an exact solution for transport in a single fracture in a porous matrix we create multiple realisations of an initial breakthrough curve. A least squares fitting routine is used to obtain a fit to each realisation, yielding a range of parameter values rather than a single set of absolute values. The suite of parameters is then used to make predictions of solute transport under lower hydraulic gradients and the uncertainty of estimated parameters and subsequent predictions of solute transport is compared. The results of this study show that predictions of breakthrough curve characteristics (first inflection point time, peak arrival time and peak concentration) for groundwater flow speeds with orders of magnitude smaller than that at which a test is conducted can sometimes be determined even more accurately than the fracture and matrix parameters.     

Numerical analysis of biological clogging in two-dimensional sand box experiments

Two-dimensional models for biological clogging and sorptive trace transport were used to study the progress of clogging in a sand box experiment. The sand box had been inoculated with a strip of bacteria and exposed to a continuous injection of nitrate and acetate. Brilliant Blue was regularly injected during the clogging experiment and digital images of the tracer movement had been converted to concentration maps using an image analysis. The calibration of the models to the Brilliant Blue observations shows that Brilliant Blue has a solid biomass dependent sorption that is not compliant with the assumed linear constant Kd behaviour. It is demonstrated that the dimensionality of sand box experiments in comparison to column experiments results in a much lower reduction in hydraulic conductivity (factor of 100) and that the bulk hydraulic conductivity of the sand box decreased only slightly. However, in the central parts of the clogged area, the observations and simulations clearly show a complex picture of flow diverting the injected nutrients around the clogged area as fingers. The calibration of the model demonstrates that the physical and microbiological processes (advection, dispersion, attachment-detachment, growth-decay) are all needed to capture the progress of clogging.     

Incorporating layer- and local-scale heterogeneities in numerical simulation of unsaturated flow and tracer transport

This study characterizes layer- and local-scale heterogeneities in hydraulic parameters (i.e., matrix permeability and porosity) and investigates the relative effect of layer- and local-scale heterogeneities on the uncertainty assessment of unsaturated flow and tracer transport in the unsaturated zone of Yucca Mountain, USA. The layer-scale heterogeneity is specific to hydrogeologic layers with layerwise properties, while the local-scale heterogeneity refers to the spatial variation of hydraulic properties within a layer. A Monte Carlo method is used to estimate mean, variance, and 5th, and 95th percentiles for the quantities of interest (e.g., matrix saturation and normalized cumulative mass arrival). Model simulations of unsaturated flow are evaluated by comparing the simulated and observed matrix saturations. Local-scale heterogeneity is examined by comparing the results of this study with those of the previous study that only considers layer-scale heterogeneity. We find that local-scale heterogeneity significantly increases predictive uncertainty in the percolation fluxes and tracer plumes, whereas the mean predictions are only slightly affected by the local-scale heterogeneity. The mean travel time of the conservative and reactive tracers to the water table in the early stage increases significantly due to the local-scale heterogeneity, while the influence of local-scale heterogeneity on travel time gradually decreases over time. Layer-scale heterogeneity is more important than local-scale heterogeneity for simulating overall tracer travel time, suggesting that it would be more cost-effective to reduce the layer-scale parameter uncertainty in order to reduce predictive uncertainty in tracer transport.     

Evaluation of groundwater flow patterns around a dual-screened groundwater circulation well

Dual-screened groundwater circulation wells (GCWs) can be used to remove contaminant mass and to mix reagents in situ. GCWs are so named because they force water in a circular pattern between injection and extraction screens. The radial extent, flux and direction of the effective flow of this circulation cell are difficult to measure or predict. The objective of this study is to develop a robust protocol for assessing GCW performance. To accomplish this, groundwater flow patterns surrounding a GCW are assessed using a suite of tools and data, including: hydraulic head, in situ flow velocity, measured hydraulic conductivity data from core samples, chemical tracer tests, contaminant distribution data, and numerical flow and transport models. The hydraulic head data show patterns that are consistent with pumping on a dual-screened well, however, many of the observed changes are smaller than expected. In situ thermal perturbation flow sensors successfully measured horizontal flow, but vertical flow could not be determined with sufficient accuracy to be useful in mapping flow patterns. Two types of chemical tracer tests were utilized at the site and showed that much of the flow occurs within a few meters of the GCW. Flow patterns were also assessed based on changes in contaminant (trichloroethylene, TCE) concentrations over time. The TCE data clearly showed treated water moving away from the GCW at shallow and intermediate depths, but the circulation of that water back to the well, except very close to the well, was less clear. Detailed vertical and horizontal hydraulic conductivities were measured on 0.3 m-long sections from a continuous core from the GCW installation borehole. The measured vertical and horizontal hydraulic conductivity data were used to construct numerical flow and transport models, the results of which were compared to the head, velocity and concentration data. Taken together, the field data and modeling present a fairly consistent picture of flow and transport around the GCW. However, the time and expense associated with conducting all of those tests would be prohibitive for most sites. As a consequence, a sequential protocol for GCW characterization is presented here in which the number of tools used can be adjusted to meet the needs of individual sites. While not perfect, we believe that this approach represents the most efficient means for evaluating GCW performance.     

The influence of atmospheric stability on pollutant transport by slope winds

The results of a field investigation into pollutant transport by slope flows are presented. During the study, ozone levels were monitored for eight days at three locations along a mountain slope extending above the Los Angeles Air Basin. In addition, tracer tests were conducted during two afternoons during the study period. The tests were conducted on days with widely varying atmospheric stability and indicate the effect of a strongly stable capping layer on pollutant transport by upslope flows. The experimental results indicated at least two mechanisms for the return of polluted air to the valley below. Under weakly stable conditions, the often noted return of pollutants via night-time downslope winds was observed. In addition, under more strongly stable conditions, a daytime recirculation mechanism consistent with that described by Vergeiner (1982) was observed. The tests also indicated that the slope flow layer depth and speed decreased with increasing atmospheric stability. In addition, the rate of transport and dilution of pollutants in a slope flow appears to be influenced by the entrainment and growth of the boundary layer, limiting the applicability of models that neglect these processes.     

曝气对水平潜流人工湿地水力特性的影响

通过构建曝气及未曝气潜流人工湿地小试实验系统,以NaCl为示踪剂开展示踪实验,研究曝气对人工湿地水力特性的影响。实验结果表明,两对比系统均存在不同程度的短流及死区现象,短流主要发生在床体表层,而死区则存在于床体底层。其中未曝气人工湿地系统的流场分布不均匀现象较为严重,示踪剂滞留在床体底层难以回收,系统水力效率较低(0.56)。比较而言,由于气流对水体的扰动作用,曝气对人工湿地系统水力效率有明显改善作用,减缓了床体表层水流速度,提高了示踪剂回收率,缩小了死区的范围,曝气人工湿地系统的水力效率为0.75。