Evaluation of impacts of soil fractions on phenanthrene sorption

Phenanthrene sorption to soils and soil fractions was investigated using two contrasting soils with different clay mineral and organic carbon (OC) contents in an attempt to evaluate the contribution of each soil fraction to phenanthrene sorption and the applicability of the carbon-normalized distribution constant (K(OC)) in soils. Sorbents were characterized using surface analysis, solid-state (13)C NMR analysis, and glass transition temperature (T(g)) analysis to gain a insight into the chemical nature of OC in soils. Dissolved organic carbon (DOC) in the soil solution impeded the phenanthrene sorption, while humins accounted for the predominant phenanthrene sorption in soils. The contribution of OC to phenanthrene sorption in soil would be overestimated if only a K(OC)-approach was adopted, since clay minerals could account for much of the sorption, especially when OC was low in soils. Nitrogen gas was shown to be inappropriate for probing non-polar sorption capacity. The results obtained highlight the importance of clay minerals in governing the sorption of phenanthrene in soil, and emphasize the inapplicability of the carbon-normalized distribution coefficient K(OC) in soils.     

Persistent organic pollutants in soil density fractions: distribution and sorption strength

The sorption strength of persistent organic pollutants in soils may vary among different soil organic matter (SOM) pools. We hypothesized that polycyclic aromatic hydrocarbons (PAHs) and polychlorinated biphenyls (PCBs) were unevenly distributed and had different soil organic carbon (SOC)-water partition coefficients (K(OC)) among soil density fractions. We determined the concentrations and K(OC) values of 20 PAHs and 12 PCBs in bulk samples and three density fractions (light, <2.0, medium, 2.0-2.4, and heavy, >2.4 g cm(-3)) of 11 urban topsoils (0-5 cm) from Bayreuth, Germany. The K(OC) values were determined using sequential extraction with methanol-water mixtures (35% and 65% methanol) at 60 degrees C. The sum of 20 PAH concentrations in bulk soil ranged 0.4-186 mg kg(-1), and that of 12 PCB concentrations 1.2-158 microg kg(-1). The concentrations of all PAHs and PCBs decreased in the order light>medium>heavy fraction. When normalized to the SOC concentrations, PAH concentrations were significantly higher in the heavy than in the other density fractions. The K(OC) values of the PAHs in density fractions were 3-20 times higher than those of the PCBs with similar octanol-water partition coefficients (K(OW)). The K(OC) values of individual PAHs and PCBs varied up to a factor of 1000 among the studied soils and density fractions. The K(OC) values of 5- and 6-ring PAHs tended to be highest in the heavy fraction, coinciding with their enrichment in this fraction. For the other PAHs and all PCBs, the K(OC) values did not differ among the density fractions. Thus, there is no relationship between sorption strength and distribution among density fractions, indicating that density fractionation is not a suitable tool to distinguish among differently reactive PAH and PCB pools in soils.     

Effect of metals on the adsorption and extractability of 14C-phenanthrene in soils

The fate of polycyclic aromatic hydrocarbons (PAHs) in contaminated soils may be affected by several environmental factors including the presence of co-contaminants. This study was conducted in order to assess the effect of metals on (i) the adsorption of 14C-phenanthrene in soils and (ii) its extractability and ability to form non-extractable residues. The first objective was accomplished using batch adsorption experiments with an uncontaminated agricultural soil spiked with the metals Cd, Cu, Pb, and Zn. Adsorption of phenanthrene was significantly higher after the addition of the metals (Kf = 21.48 vs. 8.55) and the desorption less readily reversible when compared to the unspiked soil. The extractability of phenanthrene was assessed with incubation (4 months, laboratory conditions) and microlysimeter experiments (6 months, natural climatic conditions) on three soils spiked with metals. All the soils were labelled with 14C-phenanthrene. The amount of extractable phenanthrene residues was significantly higher when the metals had been added to the soils. Nevertheless, the quantity of non-extractable residues was non-significantly different between the spiked and unspiked soils. The mechanism leading to increased adsorption and extractability of phenanthrene in the presence of metals is still unknown. In perspective, it would be interesting to assess the bioavailability of PAHs in the presence of metals in further experiments.     

Correlations of nonlinear sorption of organic solutes with soil/sediment physicochemical properties

The estimation of solute sorptive behaviors is essential when direct sorption data are unavailable and will provide a convenient way to assess the fate and the biological activity of organic solutes in soil/sediment environments. In this study, the sorption of 2,4-dichlorophenol (2,4-DCP) on 19 soil/sediment samples and the sorption of 13 organic solutes on one sediment were investigated. All sorption isotherms are nonlinear and can be described satisfactorily by a simple dual-mode model (DMM): q(e)=KpCe+Q0 . bCe/(1+bCe), where Kp (mlg(-1)) is the partition coefficient; Ce (microgml(-1)) is the equilibrium concentration; Q0 (microgg(-1)) is the maximum adsorption capacity; Q0 . b (mlg(-1)) is the Langmuir-type isotherm slope in the low concentration (Henry's law) range and b (mlmicrog(-1)) is a constant related to the affinity of the surface for the solute. Based on these nonlinear sorption isotherms and similar other nonlinear isotherms, it is observed that, for both polar 2,4-DCP and nonpolar phenanthrene, Kp, Q0 and Q0 . b are linearly correlated with soil/sediment organic carbon content (f(oc) in the range of 0.118-53.7%). The results indicate that the nonlinear sorption of organic solutes results primarily from interactions with soil/sediment organic matter. The K*oc K*oc=Kp/f(oc)), Qoc (Qoc=Q0/f(oc)), Loc (Loc=Q0 . b/f(oc)) and b for a given organic solute with different soils/sediments are largely invariant. Furthermore, logK*oc, logb and logLoc for various organic solutes are correlated significantly with the solute logKow or logSw (logKow in the range of 0.9 to 5.13 and logSw in the range of -6.176 to -0.070). A fundamental empirical equation was then established to calculate approximately the nonlinear sorption from soil/sediment f(oc) and solute Sw for a given solute equilibrium concentration.     

Responses of kinetics and capacity of phenanthrene sorption on sediments to soil organic matter releasing

Soil organic matter (SOM) releasing with dissolved organic matter (DOM) formed in solution was confirmed in a sediment/water system, and the effects of SOM releasing on the sorption of phenanthrene on sediments were investigated. Inorganic salt (0–0.1 mol L^?1 NaCl) was used to adjust SOM releasing, and two sediments were prepared, the raw sediment (S1) from Weihe River, Shann’xi, China, and the eluted sediments with and without DOM supernatant remained, termed as S2a and S2b, respectively. The FTIR and ¹H NMR analysis indicate that the low molecular weight hydrophilic SOM fraction released prior to the high molecular weight hydrophobic fraction. As a response, phenanthrene sorption kinetics on S1 showed atypical and expressed as three stages: rapid sorption, pseudo sorption with partial desorption, and slow sorption, thus a defined “sorption valley” occurred in kinetic curve. In all cases, partition dominates the sorption, and sorption capacity (K_d) ranked as S2b > S1 > S2a. Compared with the alterations of sediment characters, DOM solubilization produced by SOM releasing exhibited a greater inhibitory effect on sorption with a relative contribution of 0.67. Distribution coefficients (K_doc) of PHE into DOM clusters were 2.10?×?10⁴–4.18?×?10⁴ L kg^?1, however a threshold concentration of 6.83 mg L^?1 existed in DOM solubilization. The study results will help to clarify PAHs transport and their biological fate in a sediment/water system.     

Separating the effects of organic matter-mineral interactions and organic matter chemistry on the sorption of diuron and phenanthrene

Even though it is well established that soil C content is the primary determinant of the sorption affinity of soils for non-ionic compounds, it is also clear that organic carbon-normalized sorption coefficients (K(OC)) vary considerably between soils. Two factors that may contribute to K(OC) variability are variations in organic matter chemistry between soils and interactions between organic matter and soil minerals. Here, we quantify these effects for two non-ionic sorbates-diuron and phenanthrene. The effect of organic matter-mineral interactions were evaluated by comparing K(OC) for demineralized (HF-treated) soils, with K(OC) for the corresponding whole soils. For diuron and phenanthrene, average ratios of K(OC) of the HF-treated soils to K(OC) of the whole soils were 2.5 and 2.3, respectively, indicating a substantial depression of K(OC) due to the presence of minerals in the whole soils. The effect of organic matter chemistry was determined by correlating K(OC) against distributions of C types determined using solid-state (13)C NMR spectroscopy. For diuron, K(OC) was positively correlated with aryl C and negatively correlated with O-alkyl C, for both whole and HF-treated soils, whereas for phenanthrene, these correlations were only present for the HF-treated soils. We suggest that the lack of a clear effect of organic matter chemistry on whole soil K(OC) for phenanthrene is due to an over-riding influence of organic matter-mineral interactions in this case. This hypothesis is supported by a correlation between the increase in K(OC) on HF-treatment and the soil clay content for phenanthrene, but not for diuron.     

The influence of organic matter on sorption and fate of glyphosate in soil - Comparing different soils and humic substances

Soil organic matter (SOM) is generally believed not to influence the sorption of glyphosate in soil. To get a closer look on the dynamics between glyphosate and SOM, we used three approaches: I. Sorption studies with seven purified soil humic fractions showed that these could sorb glyphosate and that the aromatic content, possibly phenolic groups, seems to aid the sorption. II. Sorption studies with six whole soils and with SOM removed showed that several soil parameters including SOM are responsible for the strong sorption of glyphosate in soils. III. After an 80 day fate experiment, ∼40% of the added glyphosate was associated with the humic and fulvic acid fractions in the sandy soils, while this was the case for only ∼10% of the added glyphosate in the clayey soils. Glyphosate sorbed to humic substances in the natural soils seemed to be easier desorbed than glyphosate sorbed to amorphous Fe/Al-oxides.     

Dissolved organic matter effects on the performance of a barrier to polycyclic aromatic hydrocarbon transport by groundwater

In order to contain the movement of organic contaminants in groundwater, a subsurface sorption barrier consisting of sand or clay minerals coated with a cationic surfactant has been proposed. The effectiveness of such a sorption barrier might be affected by the presence of dissolved organic matter (DOM) in the groundwater. To study the impact of DOM on barrier performance, a series of batch experiments were performed by measuring naphthalene and phenanthrene sorption onto sand coated with cetylpyridinium chloride (CPC) and bentonite coated with hexadecyltrimethylammonium bromide (HDTMA) in the presence of various concentrations of DOM. The overall soil-water distribution coefficient (K*) of naphthalene and phenanthrene onto CPC-coated sand decreased with increasing DOM concentration, whereas the K* of the compounds onto HDTMA-coated bentonite slightly increased with increasing DOM concentration. To describe the overall distribution of polycyclic aromatic hydrocarbons (PAHs) in the systems, a competitive multiphase sorption (CMS) model was developed and compared with an overall mechanistic sorption (OMS) model. The modeling studies showed that while the OMS model did not explain the CPC-coated sand experimental results, a model that included competitive sorption between DOM and PAH did. The experimental results and the modeling study indicated that there was no apparent competition between DOM and PAH in the HDTMA-coated bentonite system, and indicated that in groundwater systems with high DOM, a barrier using HDTMA-coated bentonite might be more effective.     

Characteristics of oxytetracycline sorption and potential bioavailability in soils with various physical-chemical properties

Veterinary antibiotics are widely used for disease treatment, prevention and animal growth promoting. Frequent detection of veterinary antibiotics in environments, caused by land application of untreated or even treated antibiotics-containing animal wastes, has posed the growing concern of their adverse effect on natural ecosystems. Oxytetracycline (OTC) is one of the most widely-used veterinary antibiotics in livestock industry. OTC present as a cation, zwitterions, or net negatively charged ion in soils complicates predicting its sorption characteristics and potential bioavailability and toxicity. This study was to identify soil properties influencing OTC sorption and its subsequent bioavailability in five soils with various physical-chemical properties. A solution used to determine bioavailable analytes in soils and sediments, 1 M MgCl₂ (pH 8.5), was chosen to desorb the potentially bioavailable fraction of OTC sorbed onto soils. Our results demonstrated that soils with higher illite content and permanent cation exchange capacity have higher OTC sorption capacity, but increase the availability of sorbed OTC indicated by higher release of sorbed OTC from soils into aqueous phase in 1 M MgCl₂ (pH 8.5). Reversely, soil organic matter (SOM), clay, kaolinite, variable cation exchange capacity, DCB-Fe and -Al have lower OTC sorption capacity, but decrease the release of sorbed OTC from soils into 1 M MgCl₂. These findings indicate that SOM and clay greatly influence OTC adsorption and potential availability. This study contributes significantly to our understanding of the potential bioavailability of sorbed OTC and the effects of soil properties on OTC sorption behaviors in soils.     

Monometal and competitive adsorption of heavy metals by sewage sludge-amended soil

Sewage sludge-amended soils may alter their ability to adsorb heavy metals over time, due to the decomposition of sludge-borne organic matter. Thus, we studied Cd, Ni, and Zn adsorption by a sewage sludge-amended soil (Typic Xerofluvent) before and after one-year incubation in both monometal and competitive systems. In the monometal system, the order of decreasing sorption was Zn>Cd>Ni. Competition significantly reduced metal K(d), especially that of Cd which decreased by nearly 50%. Over the course of the incubation there was a 31% reduction of soil organic matter content. At the same time, in competitive systems Cd K(d) significantly decreased, while Zn K(d) significantly increased, and Ni K(d) remained unaffected. This study shows that sewage sludge-amended soils may change in their ability to sorb heavy metals over time at high metal concentrations. The data suggest that Cd is likely to be of most environmental significance in such soils, since it exhibited decreased sorption under competitive conditions and as the organic matter content of the soil was reduced. The potential for long-term release of metals should be considered in the risk assessment associated with sewage sludge addition to soils, particularly in climates where degradation of organic matter is likely to be enhanced.     

Effect of organic fertilizers derived dissolved organic matter on pesticide sorption and leaching

Incorporation of organic fertilizers/amendments has been, and continues to be, a popular strategy for golf course turfgrass management. Dissolved organic matter (DOM) derived from these organic materials may, however, facilitate organic chemical movement through soils. A batch equilibrium technique was used to evaluate the effects of organic fertilizer-derived DOM on sorption of three organic chemicals (2,4-D, naphthalene and chlorpyrifos) in USGA (United States Golf Association) sand, a mixed soil (70% USGA sand and 30% native soil) and a silt loam soil (Typic Fragiochrept). DOM was extracted from two commercial organic fertilizers. Column leaching experiments were also performed using USGA sand. Sorption experiments showed that sorption capacity was significantly reduced with increasing DOM concentration in solution for all three chemicals. Column experimental results were consistent with batch equilibrium data. These results suggest that organic fertilizer-derived DOM might lead to enhanced transport of applied chemicals in turf soils.     

Speciation of zinc in contaminated soils

The chemical speciation of zinc in soil solutions is critical to the understanding of its bioavailability and potential toxic effects. We studied the speciation of Zn in soil solution extracts from 66 contaminated soils representative of a wide range of field conditions in both North America and Europe. Within this dataset, we evaluated the links among the dissolved concentrations of zinc and the speciation of Zn(2+), soil solution pH, total soil Zn, dissolved organic matter (DOM), soil organic matter (SOM) and the concentrations of different inorganic anions. The solid-liquid partitioning coefficient (K(d)) for Zn ranged from 17 to 13,100Lkg(-1) soil. The fraction of dissolved Zn bound to DOM varied from 60% to 98% and the soil solution free Zn(2+) varied from 40% to 60% of the labile Zn. Multiple regression equations to predict free Zn(2+), dissolved Zn and the solid-liquid partitioning of Zn are given for potential use in environmental fate modeling and risk assessment. The multiple regressions also highlight some of the most important soil properties controlling the solubility and chemical speciation of zinc in contaminated soils.     

Enhanced desorption of phenanthrene from soils using hydroxypropyl-beta-cyclodextrin: experimental results and model predictions

Objective of this study was to evaluate the effects of hydroxypropyl-beta-cyclodextrin (HPCD) on the removal of phenanthrene from solid phase. Batch tests for the phenanthrene distribution between aqueous and solid phase were conducted in the presence of HPCD. Column tests and numerical simulations were conducted to evaluate the roles of HPCD cavities and interaction rates between water, HPCD, and solid phase in the enhanced removal of phenanthrene. Experimental results showed that HPCD was effective in removing sorbed phenanthrene from subsurface environment, primarily due to its negligible sorption to the solid phase and the partitioning of phenanthrene into HPCD cavities. From the numerical simulations, it was found that rate-limited partitioning of phenanthrene into HPCD cavities was most influential factor in the enhanced elution of phenanthrene. Sorption and desorption rate of phenanthrene between aqueous and solid phase was very fast or near equilibrium state. Interaction rates of contaminant between water, HPCD, and solid phase could be affected by other factors such as soil types and organic matter contents. Results from this study implied that HPCD flushing could be effectively applied for the removal of hydrophobic organic pollutants existing in the soils as sorbed or NAPL state.     

Simultaneous removal of organic compounds and heavy metals from soils by electrokinetic remediation with a modified cyclodextrin

Thousands of sites are contaminated with both heavy metals and organic compounds and these sites pose a major threat to public health and the environment. Previous studies have shown that electrokinetic remediation has potential to remove heavy metals and organic compounds when they exist individually in low permeability soils. This paper presents the feasibility of using cyclodextrins in electrokinetic remediation for the simultaneous removal of heavy metals and polycyclic aromatic hydrocarbons (PAHs) from low permeability soils. Kaolin was selected as a model low permeability soil and it was spiked with phenanthrene as well as nickel at concentrations of 500 mg kg-1 each to simulate typical mixed field contamination. Bench-scale electrokinetic experiments were conducted using hydroxypropyl beta-cyclodextrin (HPCD) at low (1%) and high (10%) concentrations and using deionized water in control test. A periodic voltage gradient of 2VDC cm-1 (with 5 d on and 2 d off) was applied to all the tests, and 0.01 M NaOH was added during the experiments to maintain neutral pH conditions at anode. In all tests, nickel migrated as Ni2+ ions towards the cathode and most of it was precipitated as Ni(OH)2 within the soil close to the cathode due to high pH condition generated by electrolysis reaction. The solubility of phenanthrene in the flushing solution and the amount of electroosmotic flow controlled the migration and removal of phenanthrene in all the tests. Even though high flow was generated in tests using deionized water and 1% HPCD, migration and removal of phenanthrene was low due to low solubility of phenanthrene in these solutions. The test with 10% HPCD solution showed higher solubility of phenanthrene which caused it migrate towards the cathode, but further migration and removal was retarded due to reduced electric current and electroosmotic flow. Approximately one pore volume of flushing resulted in approximately 50% removal of phenanthrene from the soil near the anode. Sustained higher electroosmotic flow with higher concentration cyclodextrin and maintaining low soil pH near cathode should be investigated to increase removal efficiency of both phenanthrene and nickel.     

Enhancement of phenanthrene adsorption on a clayey soil and clay minerals by coexisting lead or cadmium

Phenanthrene is commonly present together with heavy metals at many contaminated sites. This study investigated the influence of coexisting lead (Pb²⁺) or cadmium (Cd²⁺) on phenanthrene adsorption on soils. Batch experiments were conducted under different geochemical conditions including pH, mineral structure, organic matter content, and varying amounts of heavy metals. The results showed that the presence of heavy metals in solution at a fixed pH of 5.8 ± 0.1 enhanced phenanthrene adsorption, the extent of which was closely related to the concentrations and the electro-negativity of the metals. The enhancement on phenanthrene adsorption was positively correlated to the amount of adsorbed metals. Although Cd²⁺ is a softer Lewis acid, Pb²⁺ displayed a more significant effect as it was adsorbed to a greater extent on the soil surfaces. Thus, density of cation accumulation appears to be more influential than metal softness in enhancing phenanthrene adsorption. Moreover, with a portion of organic matter removed by heating at 550 °C, there was a stronger enhancement of phenanthrene adsorption by coexisting Pb²⁺, indicating an increasingly dominant mechanisms associated with Pb²⁺ at a lower organic matter content. Similar enhancement phenomenon was observed on bentonite and kaolinite, probably resulting from the cation-π bonding between the adsorbed soft metal cations and the aromatic ring of phenanthrene in solution. The desorption experiments further suggested that the bonding of phenanthrene adsorption was strengthened in the presence of Pb²⁺ and that a larger proportion of adsorbed phenanthrene remained on the soils (residual fraction) even after sequential methanol extractions. Further spectroscopic analyses and surface characterization are required to provide direct evidence of the formation and relative significance of cation-π bond for phenanthrene adsorption.     

Enhanced Desorption of Phenanthrene from Soils Using Hydroxypropyl‐β‐cyclodextrin: Experimental Results and Model Predictions

Objective of this study was to evaluate the effects of hydroxypropyl‐β‐cyclodextrin (HPCD) on the removal of phenanthrene from solid phase. Batch tests for the phenanthrene distribution between aqueous and solid phase were conducted in the presence of HPCD. Column tests and numerical simulations were conducted to evaluate the roles of HPCD cavities and interaction rates between water, HPCD, and solid phase in the enhanced removal of phenanthrene. Experimental results showed that HPCD was effective in removing sorbed phenanthrene from subsurface environment, primarily due to its negligible sorption to the solid phase and the partitioning of phenanthrene into HPCD cavities. From the numerical simulations, it was found that rate‐limited partitioning of phenanthrene into HPCD cavities was most influential factor in the enhanced elution of phenanthrene. Sorption and desorption rate of phenanthrene between aqueous and solid phase was very fast or near equilibrium state. Interaction rates of contaminant between water, HPCD, and solid phase could be affected by other factors such as soil types and organic matter contents. Results from this study implied that HPCD flushing could be effectively applied for the removal of hydrophobic organic pollutants existing in the soils as sorbed or NAPL state.     

An independent prediction of the effect of dissolved organic matter on the transport of polycyclic aromatic hydrocarbons

The transport of polycyclic aromatic hydrocarbons (PAH) in porous media in the presence of dissolved organic matter (DOM) was predicted with a transport bicontinuum model using independently obtained relationships to derive transport parameters for describing the effect of PAH binding to the DOM. The sorption constants of PAHs to soil and their binding constants to DOM were derived from basic correlations with K(ow) (indicator of hydrophobicity). The kinetic (rate) constants were derived from previously published correlations with K(p) (sorption constant). The independently obtained sorption and rate constants were corrected for binding to DOM and were used to predict the breakthrough curves (BTC) of contaminants in the presence and the absence of DOM. Column results confirmed the independently predicted BTC of PAHs in the presence of DOM that did not sorb to the solid phase, as well as the effect of DOM on the rate of the sorption and desorption processes. These findings confirm the ability to quantitatively describe how DOM facilitates transport of contaminants in the subsurface using independently derived parameters.     

Sorption-desorption behavior of PCP on soil organic matter and clay minerals

Pentachlorophenol (PCP) contamination is a severe environmental problem due to its widespread occurrence, toxicity and recalcitrance. In order to gain a better understanding of the fate of PCP in soils, the role of the soil organic matter (SOM) and clay minerals in the PCP sorption-desorption was studied on two bulk field soils, two subsoils (i.e., SOM or clay-removed soil) and two artificial soils. The two field soils used were a silty loam from New Mexico (NM) containing 10% clay and a sandy-clay-loam from Colombia (CO) South America comprised of 18% clay minerals. The bulk CO soil containing kaolinite sorbed significantly less PCP than the NM soil. All soils depicted an apparent hysteresis during sorption. The CO bulk and subsoils desorbed 14-20% and 15-26% of the sorbed PCP respectively whereas the NM bulk and subsoils desorbed only 4-12% and 5-16%, respectively. Experiments conducted with pure clay and artificial soils indicated that the expandable clay minerals were key sorbent material. Additional studies to investigate the interaction between SOM and clay minerals are needed to fully understand sorptive phenomena.     

Cosorption study of organic pollutants and dissolved organic matter in a soil

In this study we have evaluated the effects of dissolved organic matter (DOM) on sorption of imidacloprid, 3,4-dichloroaniline (3,4-DCA) and 4-bromoaniline (4-BA) on a typical calcareous soil (Luvic Xerosol) from south-eastern Spain. Two different types of DOM were used, that is to say, dissolved natural organic matter extracts from a commercial peat (DNOM) and a high-purity tannic acid (TA) solution. The experiments were carried out in a 0.01 M CaCl2 aqueous medium at 25 degrees C. The results indicated that the presence of both DNOM and TA, over a concentration range of 15-100 mg L(-1), produced an increase in the amount of 3,4-DCA and 4-BA sorbed and a decrease in the amount of imidacloprid retained on the soil studied. A modified distribution coefficient, K(doc), has been proposed as a safer parameter for soil sorption predictions of organic pollutants and it could be of help to model the fate of these in the environment.