Control of Diesel Gaseous and Particulate Emissions with a Tube-Type Wet Electrostatic Precipitator

Abstract

In this study, experiments were performed with a bench-scale tube-type wet electrostatic precipitator (wESPs) to investigate its effectiveness for the removal of mass- and number-based diesel particulate matter (DPM), hydrocarbons (HCs), carbon monoxide (CO), and oxides of nitrogen (NO_x) from diesel exhaust emissions. The concentration of ozone (O₃) present in the exhaust that underwent a nonthermal plasma treatment process inside the wESP was also measured. A nonroad diesel generator operating at varying load conditions was used as a stationary diesel emission source. The DPM mass analysis was conducted by means of isokinetic sampling and the DPM mass concentration was determined by a gravimetric method. An electrical low-pressure impactor (ELPI) was used to quantify the DPM number concentration. The HC compounds, n-alkanes, and polycyclic aromatic hydrocarbons (PAHs) were collected on a moisture-free quartz filter together with a PUF/XAD/PUF cartridge and extracted in dichloromethane with sonication. Gas chromatography (GC)/mass spectroscopy (MS) was used to determine HC concentrations in the extracted solution. A calibrated gas combustion analyzer (Testo 350) and an O₃ analyzer were used for quantifying the inlet and outlet concentrations of CO and NO_x (nitric oxide [NO] + nitrogen dioxide [NO₂]), and O₃ in the diesel exhaust stream. The wESP was capable of removing approximately 67–86% of mass- and number-based DPM at a 100% exhaust volumetric flow rate generated from 0- to 75-kW engine loads. At 75-kW engine load, increasing gas residence time from approximately 0.1 to 0.4 sec led to a significant increase of DPM removal efficiency from approximately 67 to more than 90%. The removal of n-alkanes, 16 PAHs, and CO in the wESP ranged from 31 to 57% and 5 to 38%, respectively. The use of the wESP did not significantly affect NO_x concentration in diesel exhaust. The O₃ concentration in diesel exhaust was measured to be less than 1 ppm. The main mechanisms responsible for the removal of these pollutants from diesel exhaust are discussed.     

Application for a newly developed high-capacity NOx denuder: low-NOx diesel transformation experiments

To conduct low oxides of nitrogen (NOx) chamber experiments with modern diesel emissions (DE), a high-capacity NO, denuder was developed and used at the European Photoreactor (EUPHORE) outdoor simulation chamber. The denuder displayed a sufficient NOx storage capacity for use with DE, and efficient removal of NO, during injections of DE was achieved (>98%). Degradation of the denuder performance after repeated regeneration by heating (400 degrees C) and flushing with an air/oxygen ratio of 2:1 was not observed for a total of nine experiments. Evaluation of dark (with chamber cover closed) experiments (four in total) with and without the denuder in-line revealed some reduction (22%) of diesel particulate matter (DPM) with use of the denuder, most likely a result of impaction or settling of DPM during DE transit. However, DPM reduction may have also been a result of reductions in effective load of the engine-dyno system during the DE injections. Extensive chemical characterization of DPM revealed no significant perturbation of major compound groups associated with denuder use, except for nitrated polyaromatic hydrocarbon (NPAH) concentrations. The implications of high-NOx experiments without the use of a NOx denuder are discussed.     

Diurnal and weekday variations in the source contributions of ozone precursors in California's South Coast Air Basin

For at least 30 years, ozone (O3) levels on weekends in parts of California's South Coast (Los Angeles) Air Basin (SoCAB) have been as high as or higher than on weekdays, even though ambient levels of O3 precursors are lower on weekends than on weekdays. A field study was conducted in the Los Angeles area during fall 2000 to test whether proposed relationships between emission sources and ambient nonmethane hydrocarbon (NMHC) and oxides of nitrogen (NOx) levels can account for observed diurnal and day-of-week variations in the concentration and proportions of precursor pollutants that may affect the efficiency and rate of O3 formation. The contributions to ambient NMHC by motor vehicle exhaust and evaporative emissions, estimated using chemical mass balance (CMB) receptor modeling, ranged from 65 to 85% with minimal day-of-week variation. Ratios of ambient NOx associated with black carbon (BC) to NOx associated with carbon monoxide (CO) were approximately 1.25 +/- 0.22 during weekdays and 0.76 +/- 0.07 and 0.52 +/- 0.07 on Saturday and Sunday, respectively. These results demonstrate that lower NOx emissions from diesel exhaust can be a major factor causing lower NOx mixing ratios and higher NMHC/NOx ratios on weekends. Nonmobile sources showed no significant day-of-week variations in their contributions to NMHC. Greater amounts of gasoline emissions are carried over on Friday and Saturday evenings but are, at most, a minor factor contributing to higher NMHC/NOx ratios on weekend mornings.     

Determination of PAHs in diesel particulate matter using thermal extraction and solid phase micro-extraction

Determination of polycyclic aromatic hydrocarbons (PAHs) from chemical analysis of the diesel particulate matter (DPM) requires considerable sampling expertise and is often time-consuming because sample preparation demands strict extraction procedures due to the complex nature of the DPM matrix. In this study, a method to measure the emissions of the 16-U.S. Environmental Protection Agency (EPA) priority PAHs adsorbed in diesel particles has been developed. This method involves the capture of the DPM in glass microfibre filters, thermal extraction of the compounds from the particulate matrix in a thermogravimetric analyzer (TGA), determination of the concentration by means of a solid phase micro-extraction (SPME) fibre and subsequent analysis using a gas chromatograph coupled to a mass spectrometer (GC/MS). Analyses of a fully characterised DPM prepared by the National Institute of Standards and Technology, NIST (SRM 1650b), were performed and calculated errors showed that the method is capable of giving reliable quantitative data. Additionally, DPM collected from a diesel engine was analyzed and the results showed the high method sensitivity to the engine operating conditions.     

低温等离子体处理柴油机NOx和PM试验研究

建立了一种具有较强实用性的介质阻挡放电等离子体反应器试验装置.借助静态试验研究其放电特性,通过发动机台架试验探讨了利用低温等离子体处理柴油机2种主要有害排放物NOx和PM的效果和化学反应机理,并通过模拟试验作了处理PM的进一步验证.试验结果表明,放电功率对于低温等离子体活性成分的产生有重要影响,应当优选放电参数以获得高的放电功率从而达到更好的处理效果;采用低温等离子体处理柴油机排气,NOx总量变化不大,主要将NO转化成NO2;低温等离子体可以有效去除柴油机排气中的PM,去除率随能量密度的增大而提高.     

Generation and characterization of diesel exhaust in a facility for controlled human exposures

An idling medium-duty diesel truck operated on ultralow sulfur diesel fuel was used as an emission source to generate diesel exhaust for controlled human exposure. Repeat tests were conducted on the Federal Test Procedure using a chassis dynamometer to demonstrate the reproducibility of this vehicle as a source of diesel emissions. Exhaust was supplied to a specially constructed exposure chamber at a target concentration of 100 microg x m(-3) diesel particulate matter (DPM). Spatial variability within the chamber was negligible, whereas emission concentrations were stable, reproducible, and similar to concentrations observed on the dynamometer. Measurements of nitric oxide, nitrogen dioxide, carbon monoxide, particulate matter (PM), elemental and organic carbon, carbonyls, trace elements, and polycyclic aromatic hydrocarbons were made during exposures of both healthy and asthmatic volunteers to DPM and control conditions. The effect of the so-called "personal cloud" on total PM mass concentrations was also observed and accounted for. Conventional lung function tests in 11 volunteer subjects (7 stable asthmatic) did not demonstrate a significant change after 2-hr exposures to diesel exhaust. In summary, we demonstrated that this facility can be effectively and safely used to evaluate acute responses to diesel exhaust exposure in human volunteers.     

The effect of diesel fuel sulfur content on particulate matter emissions for a nonroad diesel generator

The effect of sulfur content on diesel particulate matter (DPM) emissions was studied using a diesel generator (Generac Model SD080, rated at 80 kW) as the emission source to simulate nonroad diesel emissions. A load simulator was used to apply loads to the generator at 0, 25, 50, and 75 kW, respectively. Three diesel fuels containing 500, 2100, and 3700 ppm sulfur by weight were selected as generator fuels. The U.S. Environmental Protection Agency sampling Method 5 "Determination of Particulate Matter Emissions from Stationary Sources" together with Method 1A "Sample and Velocity Traverses for Stationary Sources with Small Stacks or Ducts" was adopted as a reference method for measurement of the exhaust gas flow rate and DPM mass concentration. The effects of various parameters on DPM concentration have been studied, such as fuel sulfur contents, engine loads, and fuel usage rates. The increase of average DPM concentrations from 3.9 mg/Nm3 (n cubic meter) at 0 kW to 36.8 mg/Nm3 at 75 kW is strongly correlated with the increase of applied loads and sulfur content in the diesel fuel, whereas the fuel consumption rates are only a function of applied loads. An empirical correlation for estimating DPM concentration is obtained when fuel sulfur content and engine loads are known for these types of generators: Y = Zm(alphaX + beta), where Y is the DPM concentration, mg/m3, Z is the fuel sulfur content, ppm(w) (limited to 500-3700 ppm(w)), X is the applied load, kW, m is the constant, 0.407, alpha and beta are the numerical coefficients, 0.0118 +/- 0.0028 (95% confidence interval) and 0.4535 +/- 0.1288 (95% confidence interval), respectively.     

Generation and Characterization of Diesel Exhaust in a Facility for Controlled Human Exposures

Abstract

An idling medium-duty diesel truck operated on ultralow sulfur diesel fuel was used as an emission source to generate diesel exhaust for controlled human exposure. Repeat tests were conducted on the Federal Test Procedure using a chassis dynamometer to demonstrate the reproducibility of this vehicle as a source of diesel emissions. Exhaust was supplied to a specially constructed exposure chamber at a target concentration of 100 µg · m^-3 diesel particulate matter (DPM). Spatial variability within the chamber was negligible, whereas emission concentrations were stable, reproducible, and similar to concentrations observed on the dynamometer. Measurements of nitric oxide, nitrogen dioxide, carbon monoxide, particulate matter (PM), elemental and organic carbon, carbonyls, trace elements, and polycyclic aromatic hydrocarbons were made during exposures of both healthy and asthmatic volunteers to DPM and control conditions. The effect of the so-called “personal cloud” on total PM mass concentrations was also observed and accounted for. Conventional lung function tests in 11 volunteer subjects (7 stable asthmatic) did not demonstrate a significant change after 2-hr exposures to diesel exhaust. In summary, we demonstrated that this facility can be effectively and safely used to evaluate acute responses to diesel exhaust exposure in human volunteers.     

Catalytic performance of Ag/Al2O3-C2H5OH-Cu/Al2O3 system for the removal of NOx from diesel engine exhaust

The selective catalytic reduction (SCR) of NOx by C(2)H(5)OH was studied in excess oxygen over Ag/Al(2)O(3) catalysts with different Ag loadings at lab conditions. The 4% Ag/Al(2)O(3) has the highest activity for the C(2)H(5)OH-SCR of NOx with a drawback of simultaneously producing CO and unburned THC in effluent gases. An oxidation catalyst 10% Cu/Al(2)O(3) was directly placed after the Ag/Al(2)O(3) to remove CO and unburned THC. Washcoated honeycomb catalysts were prepared based on the 4% Ag/Al(2)O(3) and 10% Cu/Al(2)O(3) powders and tested for the C(2)H(5)OH-SCR of NOx on a diesel engine at the practical operating conditions. Compared with the Ag/Al(2)O(3) powder, the Ag/Al(2)O(3) washcoated honeycomb catalyst (SCR catalyst) has a similar activity for NOx reduction by C(2)H(5)OH and the drawback of increasing the CO and unburned THC emissions. Using the SCR+Oxi composite catalyst with the optimization of C(2)H(5)OH addition, the diesel engine completely meets EURO III emission standards.     

工业废气中氮氧化物的治理研究

对碱液吸收和活性炭吸附两级联合治理氮氧化物废气进行了实验研究,结果表明:对于氮氧化物进口浓度为7000～10 000 mg/m3的氮氧化物废气,氮氧化物的平均脱除率可以达到99%,出口浓度低于99 mg/m3;还进行了以硝酸溶液、双氧水溶液和高锰酸钾溶液为氧化剂湿法氧化碱吸收的实验研究,结果显示3种氧化剂都能显著提高氮氧化物的脱除率,其中以高锰酸钾溶液作氧化剂的脱除效果最好,其次是双氧水溶液.     

A method for removal of CO from exhaust gas using pulsed corona discharge

An experimental study of the oxidation of CO in exhaust gas from a motorcycle has been carried out using plasma chemical reactions in a pulsed corona discharge. In the process, some main parameters, such as the initial CO concentration, amplitude and frequency of pulses, residence time, reactor volume, and relative humidity (RH), as well as their effects on CO removal characteristics, were investigated. O3, which is beneficial to reducing CO, was produced during CO removal. When the exhaust gas was at ambient temperature, more than 80% CO removal efficiency was realized at an initial concentration of 288 ppm in a suitable range of the parameters.     

Diesel reformulation using bio-derived propanol to control toxic emissions from a light-duty agricultural diesel engine

In the Indian agricultural sector, millions of diesel-driven pump-sets were used for irrigation purposes. These engines produce carcinogenic diesel particulates, toxic nitrogen oxides (NOx), and carbon monoxide (CO) emissions which threaten the livelihood of large population of farmers in India. The present study investigates the use of n-propanol, a less-explored high carbon bio-alcohol that can be produced by sustainable pathways from industrial and crop wastes that has an attractive opportunity for powering stationary diesel engines meant for irrigation and rural electrification. This study evaluates the use of n-propanol addition in fossil diesel by up to 30% by vol. and concurrently reports the effects of exhaust gas recirculation (EGR) on emissions of an agricultural DI diesel engine. Three blends PR10, PR20, and PR30 were prepared by mixing 10, 20, and 30% by vol. of n-propanol with fossil diesel. Results when compared to baseline diesel case indicated that smoke density reduced with increasing n-propanol fraction in the blends. PR10, PR20, and PR30 reduced smoke density by 13.33, 33.33, and 60%, respectively. NOx emissions increased with increasing n-propanol fraction in the blends. Later, three EGR rates (10, 20, and 30%) were employed. At any particular EGR rate, smoke density remained lower with increasing n-propanol content in the blends under increasing EGR rates. NOx reduced gradually with EGR. At 30% EGR, the blends PR10, PR20, and PR30 reduced NOx emissions by 43.04, 37.98, and 34.86%, respectively when compared to baseline diesel. CO emissions remained low but hydrocarbon (HC) emissions were high for n-propanol/diesel blends under EGR. Study confirmed that n-propanol could be used by up to 30% by vol. with diesel and the blends delivered lower soot density, NOx, and CO emissions under EGR.     

Selected ion chromatograms and tandem mass spectrometry for detection of trace polycyclic aromatic hydrocarbons in diesel exhaust

Polycyclic aromatic hydrocarbon (PAH) measurements are essential for scientists and engineers who investigate these anthropogenic compounds. Diesel engines contribute to the problem, so analysts are measuring PAHs from these sources. However, diesel exhaust presents special problems for precise analytical measurements. The exhaust matrix is very complex; consequently, PAH detection sensitivity deteriorates, especially for trace PAHs in the exhaust. Yet, these are conditions and amounts that exist in real samples. Nonetheless, selected ion chromatogram (SIC) and tandem mass spectrometry (MS/MS) techniques improve trace PAH detection; ion trap technology makes both mass techniques possible. The purpose of this investigation was to evaluate SIC and MS/MS for applications to measure PAHs in diesel exhaust samples. The signal-to-noise ratio for accurate quantitation improves, relative to traditional mass techniques, because these techniques ignore or eliminate interfering components. On a VF-5MS chromatographic column, these techniques improve sensitivity and reproducibility. They produce a superior limit of detection in the useful range for PAH samples extracted from actual engine exhaust, 10-30 pg for the smaller PAHs and 1-6 ng for the larger PAHs. The results with SIC and MS/MS are reproducible, so analysts can report PAH amounts with defined statistical confidence intervals. SIC and MS/MS improve detection for trace PAHs in convoluted diesel exhaust samples.     

Effects of a zeolite-selective catalytic reduction system on comprehensive emissions from a heavy-duty diesel engine

The effects of a zeolite urea-selective catalytic reduction (SCR) aftertreatment system on a comprehensive spectrum of chemical species from diesel engine emissions were investigated in this study. Representative samples were collected with a newly developed source dilution sampling system after an aging process designed to simulate atmospheric dilution and cooling conditions. Samples were analyzed with established procedures and compared between the measurements taken from a baseline heavy-duty diesel engine and also from the same engine equipped with the exhaust aftertreatment system. The results have shown significant reductions for nitrogen oxides (NOx), carbon monoxide, total hydrocarbons, polycyclic aromatic hydrocarbons (PAHs), and organic carbon (OC) emissions. Additionally, less significant yet notable reductions were observed for particulate matter mass and metals emissions. Furthermore, the production of new species was not observed with the addition of the zeolite urea-SCR system joined with a downstream oxidation catalyst.     

Selected Ion Chromatograms and Tandem Mass Spectrometry for Detection of Trace Polycyclic Aromatic Hydrocarbons in Diesel Exhaust

Abstract

Polycyclic aromatic hydrocarbon (PAH) measurements are essential for scientists and engineers who investigate these anthropogenic compounds. Diesel engines contribute to the problem, so analysts are measuring PAHs from these sources. However, diesel exhaust presents special problems for precise analytical measurements. The exhaust matrix is very complex; consequently, PAH detection sensitivity deteriorates, especially for trace PAHs in the exhaust. Yet, these are conditions and amounts that exist in real samples. Nonetheless, selected ion chromatogram (SIC) and tandem mass spectrometry (MS/MS) techniques improve trace PAH detection; ion trap technology makes both mass techniques possible. The purpose of this investigation was to evaluate SIC and MS/MS for applications to measure PAHs in diesel exhaust samples. The signal-to-noise ratio for accurate quantitation improves, relative to traditional mass techniques, because these techniques ignore or eliminate interfering components. On a VF-5MS chromatographic column, these techniques improve sensitivity and reproducibility. They produce a superior limit of detection in the useful range for PAH samples extracted from actual engine exhaust, 10–30 pg for the smaller PAHs and 1–6 ng for the larger PAHs. The results with SIC and MS/MS are reproducible, so analysts can report PAH amounts with defined statistical confidence intervals. SIC and MS/MS improve detection for trace PAHs in convoluted diesel exhaust samples.     

Effect of methyl tertiary butyl ether concentrations on exhaust emissions from gasoline used in the metropolitan area of Mexico City

In this work, the primary objective was to assess the impact of oxygenated fuel on the exhaust emissions from an important fraction of vehicles in the Metropolitan Area of Mexico City (MAMC). The results aim to provide information on the actual effect of MTBE on a fleet that represents more than 60% of the in-use vehicles in the MAMC. Ten vehicles were tested with a low-octane base gasoline, and 10 more with a regular-grade unleaded base gasoline. Three MTBE concentrations, 5, 10, and 15 vol %, were tested following the U.S. Federal Test Procedure (FTP). CO, total HC, and NOx from the exhaust gases were quantitatively evaluated and also characterized for FTP speciated organic emissions. From this data, the O3-forming potential of the fuels was calculated. Results show that for the fleet using low-octane gasoline, the addition of 10% MTBE substantially reduced CO emissions, but total HC concentration in the exhaust showed a modest decrease. For the regular gasoline, the 10% MTBE blend seemed to be the best choice, but there was not a significant decrease in emissions. The specific reactivity of each fuel, expressed in grams of O3 per gram of nonmethane organic gases, increased with MTBE concentration in both cases. This result is important to consider, especially for a region like Mexico City, which has high atmospheric O3 concentrations.     

Exhaust temperature profiles for application of passive diesel particulate filters to solid waste collection vehicles in California

To reduce public exposure to diesel particulate matter (DPM), the California Air Resources Board has begun adoption of a series of rules to reduce these emissions from in-use heavy-duty vehicles. Passive diesel particulate filter (DPF) after-treatment technologies are a cost-effective method to reduce DPM emissions and have been used on a variety of vehicles worldwide. Two passive DPFs were interim-verified in California and approved federally for use in most 1994--2002 engine families for vehicles meeting min engine exhaust temperature requirements for successful filter regeneration. Some vehicles, however, may not be suited to passive DPFs because of lower engine exhaust temperatures. The purpose of this study was to determine the applicability of two types of passive DPFs to solid waste collection vehicles, the group of vehicles for which California recently mandated in-use DPM reductions. We selected 60 collection vehicles to represent the four main types of collection vehicle duty cycles--rolloffs, and front-end, rear, and side loaders--and collected second-by-second engine exhaust temperature readings for one week from each vehicle. As a group, the collection vehicles exhibited low engine exhaust temperatures, making the application of passive DPFs to these vehicles difficult. Only 35% of tested vehicles met the temperature requirements for one passive DPF, whereas 60% met the temperature requirements for the other. Engine exhaust temperatures varied by vehicle type. Side and front-end loaders met the engine exhaust temperature requirements in the greatest number of cases with approximately 50-90% achieving the required regeneration temperatures. Only 8-25% of the rear loader and roll-off collection vehicles met the engine exhaust temperature requirements. Solid waste collection vehicles represent a diverse fleet with a variety of duty cycles. Low engine exhaust temperatures will need to be addressed for successful use of passive DPFs in this application.     

Comparison of vehicle exhaust emissions from modified diesel fuels

Three diesel fuels, one oil sand-derived (OSD) diesel serving as base fuel, one cetane-enhanced base fuel, and one oxygenate [diethylene glycol dimethyl ether (DEDM)]-blended base fuel, were tested for their emission characterizations in vehicle exhaust on a light-duty diesel truck that reflects the engine technology of the 1994 North American standard. Both the cetane-enhanced and the oxygenate-blended fuels were able to reduce regulated [CO, particulate matter (PM), total hydrocarbon (THC)] and nonregulated [polyaromatic hydrocarbons (PAHs), carbonyls, and other volatile organic chemicals] emissions, except for nitrogen oxides (NO(x)), compared with the base fuel. Although burning a fuel that contains oxygen could conceivably yield more oxygenated compounds in emissions, the oxygenate-blended diesel fuel resulted in reduced emissions of formaldehyde along with hydrocarbons such as benzene, 1,3-butadiene, and PAHs. Reductions in nitro-PAH emissions have been observed in both the cetane-enhanced and oxygenated fuels. This further demonstrates the benefits of using a cetane enhancer and the oxygenated fuel component.     

Effects of diesel/biodiesel blends on regulated and unregulated pollutants from a passenger vehicle operated over the European and the Athens driving cycles

This paper presents the regulated and unregulated exhaust emissions of a diesel passenger vehicle, operated with low sulphur automotive diesel and soy methyl ester blends. Emission and fuel consumption measurements were conducted under real driving conditions (Athens Driving Cycle, ADC) and compared with those of a modified New European Driving Cycle (NEDC) using a chassis dynamometer. A Euro II compliant diesel vehicle was used in this study, equipped with an indirect injection diesel engine, fuelled with diesel fuel and biodiesel blends at proportions of 5, 10, and 20% respectively. Unregulated emissions of 11 polycyclic aromatic hydrocarbons (PAHs), 5 nitro-PAHs, 13 carbonyl compounds (CBCs) and the soluble organic fraction (SOF) of the particulate matter were measured. Qualitative hydrocarbon analysis was also performed on the SOF. Regulated emissions of NO_x, CO, HC, CO₂, and PM were also measured over the two test cycles. It was established that some of the emissions measured over the (hot-start) NEDC differed from the real-world cycle. Significant differences were also observed in the vehicle's fuel consumption between the two test cycles. The addition of biodiesel reduced the regulated emissions of CO, HC and PM, while an increase in NO_x was observed over the ADC. Carbonyl emissions, PAHs and nitro-PAHs were reduced with the addition of biodiesel over both driving cycles.     

Exhaust Temperature Profiles for Application of Passive Diesel Particulate Filters to Solid Waste Collection Vehicles in California

Abstract

To reduce public exposure to diesel particulate matter (DPM), the California Air Resources Board has begun adoption of a series of rules to reduce these emissions from in-use heavy-duty vehicles. Passive diesel particulate filter (DPF) after-treatment technologies are a cost-effective method to reduce DPM emissions and have been used on a variety of vehicles worldwide. Two passive DPFs were interim-verified in California and approved federally for use in most 1994–2002 engine families for vehicles meeting min engine exhaust temperature requirements for successful filter regeneration. Some vehicles, however, may not be suited to passive DPFs because of lower engine exhaust temperatures. The purpose of this study was to determine the applicability of two types of passive DPFs to solid waste collection vehicles, the group of vehicles for which California recently mandated in-use DPM reductions. We selected 60 collection vehicles to represent the four main types of collection vehicle duty cycles—roll-offs, and front-end, rear, and side loaders—and collected second-by-second engine exhaust temperature readings for one week from each vehicle. As a group, the collection vehicles exhibited low engine exhaust temperatures, making the application of passive DPFs to these vehicles difficult. Only 35% of tested vehicles met the temperature requirements for one passive DPF, whereas 60% met the temperature requirements for the other. Engine exhaust temperatures varied by vehicle type. Side and front-end loaders met the engine exhaust temperature requirements in the greatest number of cases with ～50–90% achieving the required regeneration temperatures. Only 8–25% of the rear loader and roll-off collection vehicles met the engine exhaust temperature requirements. Solid waste collection vehicles represent a diverse fleet with a variety of duty cycles. Low engine exhaust temperatures will need to be addressed for successful use of passive DPFs in this application.