Dechlorination of polyvinyl chloride in NaOH/ethylene glycol solution by microwave heating

This study investigated the dehydrochlorination of flexible polyvinyl chloride (PVC) containing 59.2% PVC, 29.7% dioctyl phthalate (DOP), and approximately 12% stabilizers. Flexible PVC was treated with NaOH/ethylene glycol (NaOH/EG) solutions at NaOH concentrations in the range 0.5–4 mol/l and was heated in a microwave heater at a temperature between 100° and 160°C for 0–30 min. All chlorides were completely eliminated by internal heating at 160°C using microwaves for 10 min in a 1 mol/l NaOH/EG solution, and the residue was made up of hydrocarbons. The weight loss rate reached a maximum of 74.7% at a temperature of 160°C. It was discovered that the use of microwaves significantly shortened the reaction time compared to using conventional electric heaters or other external heating systems and also allowed the use of lower concentrations of NaOH. Chemical Feedstock Recycling & Other Innovative Recycling Techniques 6     

Upgrading of poly(vinyl chloride) by chemical modifications using sodium sulfide

The recycling of poly(vinyl chloride) (PVC) is one of the most important issues in the treatment of waste plastics. To improve PVC recycling, it is necessary to develop new recycling techniques, including new techniques for the dechlorination of chlorine-containing polymers. It has been established that wet dechlorination of PVC in NaOH/ethylene glycol solution is more effective than dry dechlorination. In this study, the wet process was used, and the chemical modification of PVC by nucleophilic substitution was considered for upgrading waste PVC. Chlorine was substituted in solution by several nucleophilic reagents, thus changing the properties of PVC. The reaction of PVC in Na2S/ethylene glycol solution at 170°C resulted in the formation of a mixture comprising 32% elimination and 26% substitution products. The scanning electron microscopy/energy dispersive X-ray spectroscopy mappings and elementary analysis of PVC indicated that this chlorine-substitution process led to cross-linking by sulfur.     

High efficiency chlorine removal from polyvinyl chloride (PVC) pyrolysis with a gas–liquid fluidized bed reactor

In this research a gas–liquid fluidized bed reactor was developed for removing chlorine (Cl) from polyvinyl chloride (PVC) to favor its pyrolysis treatment. In order to efficiently remove Cl within a limited time before extensive generation of hydrocarbon products, the gas–liquid fluidized bed reactor was running at 280–320 °C, where hot N₂ was used as fluidizing gas to fluidize the molten polymer, letting the molten polymer contact well with N₂ to release Cl in form of HCl. Experimental results showed that dechlorination efficiency is mainly temperature dependent and 300 °C is a proper reaction temperature for efficient dechlorination within a limited time duration and for prevention of extensive pyrolysis; under this temperature 99.5% of Cl removal efficiency can be obtained within reaction time around 1 min after melting is completed as the flow rate of N₂ gas was set around 0.47–0.85 Nm³ kg^?1 for the molten PVC. Larger N₂ flow rate and additives in PVC would enhance HCl release but did not change the final dechlorination efficiency; and excessive N₂ flow rate should be avoided for prevention of polymer entrainment. HCl is emitted from PVC granules or scraps at the mean time they started to melt and the melting stage should be taken into consideration when design the gas–liquid fluidized bed reactor for dechlorination.     

锌粉对聚氯乙烯的机械化学还原脱氯

以锌粉为还原剂进行了聚氯乙烯（PVC）的机械化学还原脱氯（简称脱氯）探索研究,考察了球磨转速、球料比（磨球与试样的质量比）、锌粉与PVC质量比等对脱氯率的影响,并对脱氯产物进行了X射线衍射、红外光谱等分析。实验结果表明,最佳工艺条件为球料比33、球磨转速528r／min、锌粉与PVC质量比9;产物中未形成结晶性氯化锌,且锌粉被氧化成ZnO;行星球磨比搅拌球磨对PVC的脱氯效果好,球磨时间超过3h,PVC的脱氯率可接近100％。     

Dechlorination and decomposition of Aroclor 1242 in real waste transformer oil using a nucleophilic material with a modified domestic microwave oven

This research was done to assess the dechlorination and decomposition of polychlorinated biphenyls (PCBs) in real waste transformer oil through a modified domestic microwave oven (MDMW). The influence of microwave power (200–1000 W), reaction time (30–600 s), polyethylene glycol (PEG) (1.5–7.5 g), iron powder (0.3–1.5 g), NaOH (0.3–1.5 g), and H₂O (0.4–2 ml) were investigated on the decomposition efficiency of PCBs existing in real waste transformer oil with MDMW. Obtained data indicate that PEG and NaOH have the greatest influence on decomposition of PCBs; while, iron did not influence, and H₂O decreased, the decomposition efficiency of PCBs. Experimental data also indicated that with the optimum amount of variables through a central composites design method (PEG = 5.34 g, NaOH = 1.17 g, Fe = 0.6 g, H₂O = 0.8 ml and microwave power 800 W), 78 % of PCBs was degraded at a reaction time of about 6 min. In addition, the PCBs decomposition without using water increased up to 100 % in the reactor with the MDMW at 6 min. Accordingly, results showed that MDMW was a very efficient factor for PCBs decomposition from waste transformer oil. Also, using microwave irradiation, availability and inexpensive materials (PEG, NaOH), and iron suggest this method as a fast, effective, and cheap method for PCB decomposition of waste oils.     

Lignin Functionalized by Thermally Curable Propargyl Groups as Heat-Resistant Polymeric Material

Lignin was chemically functionalized via Williamson etherification reaction with propargyl bromide to prepare a thermosetting bio-resin, propargyllignin. The optimum reaction conditions were found at 70?°C for 4?h under the catalysis of sodium hydroxide in the ethanol solution. The propargllignin resin had highly improved processing capability, evidenced by good solubility, low melting point (<100?°C) and thermal curability. Upon heating, propargyllignin resin solidified with an exotherm around 180?C280?°C peaking at 240?°C, implying its thermal cure reaction via ethynyl polymerization. Compared with lignin feedstock, the propargyllignin resin showed much higher thermal properties: an onset decomposition temperature of 410?°C and a residue yield of 58?% at 800?°C (for lignin, onset decomposition temperature of 250?°C and residue yield of 34?%). Different from the lignin feedstock, propargyllignin was readily applied as curable thermosetting resin for composite matrix, and exhibited high mechanical and thermal properties.     

Investigation on thermal dechlorination and catalytic pyrolysis in a continuous process for liquid fuel recovery from mixed plastic wastes

A continuous system (feeding rate >1 kg/h) consisting of thermal dechlorination pre-treatment and catalytic pyrolysis with Fe-restructured clay (Fe-RC) catalyst was developed for feedstock recycling of PVC-containing mixed plastic waste. The vented screw conveyor which was specially designed for continuous dechlorination was able to achieve dechlorination efficiency of over 90 % with a feedstock retention time longer than 35.5 min. The chlorine content of the pyrolytic oil obtained after dechlorination was in the range of 6.08–39.50 ppm, which meet the specification for reclamation pyrolytic oil in Japan. Fe-RC was found to significantly improve the yield of pyrolytic oil (achieved to 83.73 wt%) at the optimized pyrolysis temperature of 450 °C and catalyst dosage of 60 g. With the optimized parameters, Fe-RC showed high selectivity for the C₉–C₁₂ and C₁₃–C₁₉ oil fraction, which are the major constituents of kerosene and diesel fuel, demonstrating that this catalyst can be applied in the pyrolysis of mixed plastic wastes for the production of kerosene and diesel fuel. Overall, the continuous process exhibited high stability and consistently high-oil yield upon reaching steady state, indicating its potential up-scaling application in the industry.     

Methanolysis and Hydrolysis of Polycarbonate Under Moderate Conditions

Alkali-catalyzed methanolysis and hydrolysis of polycarbonate (PC) in a solvent in which PC can substantially dissolve such as N-methyl-2-pyrrolidone, 1,4-dioxane, tetrahydrofuran and so on were studied. Reaction conditions were optimized for the purpose of recycling PC in the form of bisphenol A and carbon carbonate. The results showed that both the methanolysis and hydrolysis of PC could take place under moderate conditions. Under the conditions of reaction temperature 40 °C, m(PC):m(MeOH) = 1:1, m(PC):m(NaOH) = 50:1, reaction time 35 min and using tetrahydrofuran as solvent, the methanolysis conversion of PC was almost 100% and the yield of bisphenol A was over 95%. Moreover, under the conditions of reaction temperature 100 °C, m(PC):m(H₂O) = 1:0.7, m(PC):m(NaOH) = 10:1, reaction time 8 h and using 1,4-dioxane as solvent, the hydrolysis conversion of PC was almost 100% and the yield of bisphenol A was over 94%.     

Relation between mechanochemical dechlorination rate of polyvinyl chloride and mill power consumption

A sample of polyvinyl chloride (PVC) powder was milled with CaO powder in a planetary mill for various mill operational parameters. The milled product consisted of dechlorinated hydrocarbon and water-soluble CaOHCl. The dechlorination rate of PVC was determined by the concentration of Cl⁻ ions measured in solution after dispersing the milled product in water. To evaluate the power consumption during PVC dechlorination, the mill power consumption was measured during each experimental run. In addition, media motion during planetary milling was simulated using the discrete element method (DEM), enabling calculation of the mill power consumption. The power consumption calculated by the DEM simulation compared well with the power consumption measured experimentally. The dechlorination rate correlated well with the specific mill power consumption, regardless of the sample weight. The dechlorination rate of PVC when milled with oyster shells (CaCO₃) was observed to be faster than that of the PVC/CaO system, and oyster shells could be used as a reactant for the treatment of PVC wastes. This work should be useful for the design of a reactor for the dechlorination of PVC. Chemical Feedstock Recycling & Other Innovative Recycling Techniques 6     

Surface ozonation of polyvinyl chloride for its separation from waste plastic mixture by froth floatation

Selective surface modification of polyvinyl chloride (PVC) by ozonation was evaluated to facilitate the separation of PVC from other heavy plastics with almost the same density as PVC, especially polyethylene terephthalate (PET), by the froth flotation process. The optimum froth flotation conditions were investigated, and it was found that at 40°C, 90% of PVC and PET plastics floated. The bubble size became larger and the area covered with bubbles on the plastic surface was reduced with increasing temperature. Optimum PVC separation was achieved with the flotation solution at 40°C and mixing at 180–200 rpm, even for sheet samples 10 mm in size. Combined treatment by ozonation and froth flotation is a simple, effective, and inexpensive method for PVC separation from waste plastics.     

Hydrometallurgical processing of Nd–Fe–B magnets for Nd purification

An evaluation of various metal purification processes subsequent to the leaching processing of the neodymium (Nd) product from neodymium–iron–boron (Nd–Fe–B) magnets has been conducted. These post-leaching purification processes included precipitation; replacement and electrolysis were studied in order to check the purity of the recovered neodymium. A hydrometallurgical investigation was adopted to digest the metal content of the scrap Nd–Fe–B magnets for the recovery of valuable Nd metal and other metals such as Fe, B, Co and Ni. The effect of leaching conditions such as solid-to-liquid ratio and temperature were optimized and 100 % Nd, 100 % Fe, 100 % B and 85.87 % Co leaching efficiencies were achieved under these conditions. The coating material of the magnet, Ni, achieved 50 % impregnation after increasing the reaction temperature to 70 °C. The metals present in the optimal leaching solution were recovered 99 % by pH adjustment. However, the replacement had the highest separation efficiency for the recovery of Nd metal. Further, the optimal leaching Nd–Fe–B solution was subjected to the electrolysis processes in order to verify the recovery efficiency for all metals.     

Effect of microwave irradiation on anaerobic degradability of model kitchen waste

High temperature and pressure microwave (MW) irradiation was investigated as a pre-treatment to enhance anaerobic biodegradability and methane production from a model kitchen waste (KW). Heating rates of 7.8, 3.9 and 1.9 °C/min from room temperature to a final pre-treatment temperature of 175 °C with 1 min temperature holding time were tested. MW irradiation was successful in solubilization of particulate chemical oxygen demand (COD) resulting in higher soluble COD, protein and sugar concentrations in the supernatant phase (<0.45 μm) as well as in the whole fraction of pretreated KW compared to controls (not pretreated). Anaerobic biodegradability of the supernatant and whole fractions of pretreated KW was assessed by using a batch biochemical methane potential assay (BMP) at 33 °C. Although the highest level of solubilization was achieved at a heating rate of 1.9 °C/min, improvement in anaerobic biodegradability was observed only at the fastest heating rate of 7.8 °C/min for whole waste and for all conditions with the supernatant phase. BMP indicated increased biodegradability of between 5% and 16% for the supernatant fraction relative to controls. For the whole fraction, anaerobic biodegradability improved by 9% at a heating rate of 7.8 °C/min.     

Optimization of thermo-chemical hydrolysis of kitchen wastes

Municipal Solid Wastes (MSWs) in Greece consist mainly of fermentable organic material such as food scraps (～50%) and paper residuals (～20%). The aim of this work was to study the thermo-chemical pretreatment of the kitchen waste (KW) fraction of MSW focusing on biotechnological exploitation of pretreated wastes for biofuel production. A representative sample of municipal food residues was derived by combining weighted amounts of each individual type of residue recognized in daily samples obtained from the University of Patras’ students restaurant located at the Students Residence Hall (Greece). Chemical pretreatment experiments of the representative KW sample were performed using several types of chemical solutions (i.e. H₂SO₄, HCl, NaOH, H₂SO₃) of different solute concentration (0.7%, 1.5%, 3%) at three temperatures (50, 75, 120 °C) and a range of residence times (30–120 min). Optimized results proved that chemical pretreatment of KW, using either 1.12% HCl for 94 min or 1.17% HCl for 86 min (at 100 °C), increased soluble sugars concentration by 120% compared to untreated KW. The increase of soluble sugars was mainly attributed to the mono-sugars glucose and fructose.     

Production of hydrogen by steam gasification of dehydrochlorinated poly(vinyl chloride) or activated carbon in the presence of various alkali compounds

Steam gasification of dehydrochlorinated poly(vinyl chloride) (PVC) or activated carbon was carried out in the presence of various alkali compounds at 3.0 MPa and 560°C–660°C in a batch reactor or in a semi-batch reactor with a flow of nitrogen and steam. Hydrogen and sodium carbonate were the main products, and methane and carbon dioxide were the minor products. Yields of hydrogen were high in the presence of sodium hydroxide and potassium hydroxide. The acceleration effect of the alkali compounds on the gasification reaction was as follows: KOH > NaOH > Ca(OH)₂ > Na₂CO₃. The rate of gasification increased with increasing partial steam pressure and NaOH/C molar ratio. However, the rate became saturated at a molar ratio of NaOH/C greater than 2.0.     

酸浸—萃取—沉淀法回收废锂离子电池中的钴

采用酸浸—萃取—沉淀法回收废锂离子电池中的钴。实验结果表明:废锂离子电池在600℃下煅烧5 h可将正极材料上的有机黏结剂与正极活性物质分离;正极活性物质在Na OH溶液浓度为2.0 mol/L、n(Na OH)∶n(铝)=2.5、碱浸温度为20℃的条件下碱浸反应1 h后,铝浸出率达99.7%;已除铝的正极活性物质在硫酸浓度为2.5 mol/L、H_2O_2质量浓度为7.25 g/L、液固比为10、酸浸温度为85℃的条件下酸浸反应120 min,钴浸出率高达98.0%;酸浸液在p H为3.5、萃取剂P507与Cyanex272体积比为1∶1的条件下,经2级萃取,钴萃取率为95.5%;采用H_2SO_4溶液反萃后在硫化钠质量浓度为8 g/L、反萃液p H为4的条件下沉淀反应10 min,钴沉淀率达99.9%。     

Enhanced styrene recovery from waste polystyrene pyrolysis using response surface methodology coupled with Box–Behnken design

A work applied response surface methodology coupled with Box–Behnken design (RSM-BBD) has been developed to enhance styrene recovery from waste polystyrene (WPS) through pyrolysis. The relationship between styrene yield and three selected operating parameters (i.e., temperature, heating rate, and carrier gas flow rate) was investigated. A second order polynomial equation was successfully built to describe the process and predict styrene yield under the study conditions. The factors identified as statistically significant to styrene production were: temperature, with a quadratic effect; heating rate, with a linear effect; carrier gas flow rate, with a quadratic effect; interaction between temperature and carrier gas flow rate; and interaction between heating rate and carrier gas flow rate. The optimum conditions for the current system were determined to be at a temperature range of 470–505 °C, a heating rate of 40 °C/min, and a carrier gas flow rate range of 115–140 mL/min. Under such conditions, 64.52% WPS was recovered as styrene, which was 12% more than the highest reported yield for reactors of similar size. It is concluded that RSM-BBD is an effective approach for yield optimization of styrene recovery from WPS pyrolysis.     

Recycling nickel from spent catalyst of Phu My fertilizer plant as a precursor for exhaust gas treatment catalysts preparation

In this study, a very promising way of treating and recycling spent nickel catalysts of fertilizer plants in Vietnam was proposed. Firstly, nickel was recovered from spent catalyst using HNO₃—leaching process. Results show that nickel recovery of over 90% with a purity of over 90% can be achieved with HNO₃ 2.1–2.5 M at 100?°C in 75 min. The residue after leaching is not considered as a hazardous waste according to the Vietnamese regulations. Then, the leachate solution was used as a precursor to prepare a model catalyst for exhaust gas (CO, HC, NO_x) treatment. In comparison with the catalyst prepared from the commercial nickel nitrate solution, the catalyst synthesized from recovered nickel exhibits similar properties and activities. The influence of Ni loading of Ni/alumina catalyst as well as the modification of active phase by some metals addition (Mn, Ba, Ce) was also investigated. It is feasible to modify active phase by transition metals such as Mn, Ba, and Ce for complete oxidation of CO and HC at 270?°C and a reduction of NO_x below 350?°C at high volumetric flow condition (GHSV?=?110.000 h^?1).     

Microwave Assisted Short-Time Alkaline Extraction of Birch Xylan

Efficacy of microwave energy for the extraction of xylan from birch wood as an alternative to conventional method of extraction was investigated. Effect of irradiation time and microwave power input on the solubilization of wood and yield of extracted xylan was studied. The maximum yield of xylan obtained at the higher power level was significantly lesser compared to the lower power level indicating the molecular degradation of the polymer. The highest yield of xylan (60 % of the original xylan) was obtained at the lowest power level studied, 110 W, for an irradiation time of 10 min. Comparison with conventional extraction showed that 10 min of microwave extraction provided a similar wood dissolution to that at 90 °C for 1.5 h, but with a higher yield of xylan. Characterization of the precipitated xylan indicated that the extracted xylan contained 68–88 % of xylose with the major chemical structure consisting of a linear backbone of (1-4) β-d-xylopyransoyl residues. Molecular mass of the extracted xylan indicated that the xylan extracted using microwave contained 60–70 % of high molecular weight fraction, and about 30–40 % of low molecular weight fraction, whereas xylan extracted using conventional method showed a reverse trend. Molecular mass of non-aggregated xylan was reported to be 6,000 Da (in terms of dextran equivalents). Crystallinity of wood fibers increased irrespective of the method of extraction indicating no degradation of the strength of the fibers occurred during the extraction.     

Dechlorination/detoxification of aromatic chlorides using fly ash under mild conditions

An efficient dechlorination/detroxification method for p-nitrochlorobenzene, p-chloroanisole and 1-chloronaphthalene on municipal waste incinerator fly ash in presence of reducing agents with water/alcohol mixtures was developed. Dechlorination% was higher in water/isopropanol mixture at temperature <100 °C. Metal contents of fly ash played a vital role in enhancing dechlorination at low temperature. Moreover, the fly ash particles provided the surface to accomplish reduction and substitution reactions by adsorbing the chlorinated aromatic compound, hydrogen and hydroxyl ions. The mechanism of dechlorination was envisaged.     

Studies on the dechlorination and oil-production technology of waste plastics

 Recycle technology for waste plastics containing polyvinyl chloride (PVC) has been developed in the Hokkaido National Industrial Research Institute for the production of solid and liquid fuel, and has established a recycling process which includes a dechlorination process for PVC plastics, and a two-stage catalytic pyrolysis process for plastics using zeolite catalysts. The dechlorination equipment consists of a two-axis screw extruder with a heating element, which can remove chlorine up to 99.9 wt. % from PVC containing plastics as hydrogen chloride. The product had about 44 000 kJ/kg calorific value and was fed into the next oil production process, although it could also be used as a solid fuel. Natural and synthetic zeolite were used as catalysts for the two-stage catalytic process, which produced a light oil with a boiling point which was between those of kerosene and gasoline. The yield of this oil reached 82 wt. %. The chemical type was analyzed using liquid chromatography, and was found to have many aromatic compounds. These technologies make it possible to produce a nonpolluting, high-calorie solid fuel and a liquid fuel very efficiently. Received: July 19, 2000 / Accepted: September 21, 2000