Deflector Designs for Fish Habitat Restoration

Paired current deflectors are structures that are installed on each bank of a river to locally reduce the width of the channel, thereby creating flow acceleration and promoting scouring. These instream habitat structures have been used extensively in restoration projects to create pool habitat for fish, but there are many discrepancies in deflector design recommendations in terms of orientation, height, and length. Our objectives were to (1) examine how the angle, height, and length of paired deflectors affect scour hole dimensions and potential for bank erosion; and (2) test the applicability to paired deflectors of existing equations for scour hole depth and volume. Three deflector angles (45°, 90°, and 135°), two deflector heights (with flow under and over the deflector height), and two lengths (reducing the width by 25% and 50%) were investigated using uniform sand in a laboratory flume. Results showed a 26–30% smaller scour depth resulting from 45° deflectors than from 90° deflectors and a 5–10% smaller scour depth for 135° deflectors compared to 90° deflectors. The volume of scour and the potential for bank erosion were greater when flow was under the height of the deflectors rather than overtopping and when the length of deflector was increased. When flow was under the deflector height, 135° deflectors had the highest amount of bank erosion; whereas during overtopping flow conditions, 90° deflectors had the greatest bank erosion potential. Values predicted by the model of Kuhnle and others were closest to observed scour depth and volume measurements. The assumption that upstream-oriented deflectors always generate the largest scour should be revised.     

PROFILE: Hungry Water: Effects of Dams and Gravel Mining on River Channels

/ Rivers transport sediment from eroding uplands to depositional areas near sea level. If the continuity of sediment transport is interrupted by dams or removal of sediment from the channel by gravel mining, the flow may become sediment-starved (hungry water) and prone to erode the channel bed and banks, producing channel incision (downcutting), coarsening of bed material, and loss of spawning gravels for salmon and trout (as smaller gravels are transported without replacement from upstream). Gravel is artificially added to the River Rhine to prevent further incision and to many other rivers in attempts to restore spawning habitat. It is possible to pass incoming sediment through some small reservoirs, thereby maintaining the continuity of sediment transport through the system. Damming and mining have reduced sediment delivery from rivers to many coastal areas, leading to accelerated beach erosion. Sand and gravel are mined for construction aggregate from river channel and floodplains. In-channel mining commonly causes incision, which may propagate up- and downstream of the mine, undermining bridges, inducing channel instability, and lowering alluvial water tables. Floodplain gravel pits have the potential to become wildlife habitat upon reclamation, but may be captured by the active channel and thereby become instream pits. Management of sand and gravel in rivers must be done on a regional basis, restoring the continuity of sediment transport where possible and encouraging alternatives to river-derived aggregate sources.KEY WORDS: Dams; Aquatic habitat; Sediment transport; Erosion; Sedimentation; Gravel mining     

Modeling of Vertical Solute Dispersion in a Sediment Bed Enhanced by Wave‐Induced Interstitial Flow1

Abstract: Mass (solute) transport in a stream or lake sediment bed has a significant effect on chemical mass balances and microbial activities in the sediment. A “1D vertical dispersion model” is a useful tool to analyze or model solute transfer between river or lake water and a sediment bed. Under a motionless water column, solute transfer into and within the sediment bed is by molecular diffusion. However, surface waves or bed forms create periodic pressure waves along the sediment/water interface, which in turn induce flows in the pores of the sediment bed. The enhancement of solute transport by these interstitial periodic flows in the pores has been incorporated in a 1D depth‐dependent “enhanced dispersion coefficient (D_E).” Typically, D_E diminishes exponentially with depth in the sediment bed. Relationships have been developed to estimate D_E as a function of the characteristics of sediment (particle size, hydraulic conductivity, and porosity) and pressure waves (wave length and height). In this paper, we outline and illustrate the calculation of D_E as well as the penetration depth (d_p) of the flow effect. Sample applications to illustrate the computational procedure are provided for dissolved oxygen transfer into a stream gravel bed and release of phosphorus from a lake bed. The sensitivity of the results to input parameter values is illustrated, and compared with the errors obtained when interstitial flow is ignored. Maximum values of D_E near the sediment surface can be on the order of 1 cm²/s in a stream gravel bed with standing waves, and 0.001 cm²/s in a fine sand lake bed under progressive surface waves, much larger than molecular diffusion coefficients.     

A geomorphologist's criticism of the engineering approach to channelization of gravel-bed rivers: case study of the Raba River, Polish Carpathians

River engineers use sediment transport formulas to design regulated channels in which the river's ability to transport bedload would remain in equilibrium with the delivery of materials from upstream. In gravel-bed rivers, a number of factors distort the simple relationship between particle size and hydraulic parameters at the threshold of sediment motion, inherent in the formulas. This may lead to significant errors in predicting the bedload transport rates in such streams and hence to instability of their regulated channels. The failure to recognize a nonstationary river regime may also result in unsuccessful channelization. Rapid channel incision has followed channelization of the main rivers of the Polish Carpathians in the 20th century. A case study of the Raba River shows that incision has resulted from the increase in stream power caused by channelization and the simultaneous reduction in sediment supply due to variations in basin management and a change in flood hydrographs. Calculations of bedload transport in the river by the Meyer-Peter and Müller formula are shown to have resulted in unrealistic estimates, perhaps because the different degree of bed armoring in particular cross-sections was neglected. It would have been possible to avoid improper channelization if the decreasing trend in sediment load of the Carpathian rivers had been recognized on the basis of geomorphological and sedimentological studies. Allowing the rivers to increase their sinuosity, wherever possible without an erosional threat to property and infrastructure, and preventing further in-stream gravel mining are postulated in order to arrest channel incision and reestablish the conditions for water and sediment storage on the floodplains.     

INFLUENCES OF INCREASED SAND DELIVERY ON THE MORPHOLOGY OF SAND AND GRAVEL CHANNELS1

ABSTRACT A flume study was conducted to examine (1)changes in the particle-size distribution of sediments in riffles due to the proportion of sand in transport and the total rate of bedload transport at the time the riffle is deposited and (2) the effect of high sand transport rates on the stability of gravel riffles. The median particle size of sediment deposited in the riffle was larger than that of the sediment in transport. Small but significant (a = 0.05) decreases in the median particle size of riffle sediments resulted as the sand-to-gravel ratio. Increased concentrations of sand in transport caused previously stable gravel riffles to undergo scour. These results, in combination with information from other studies, suggest that an alluvial channel with pool-riffle sequences and with sand and gravel beds may respond to an increased delivery of sand by reducing form roughness. Form roughness can be reduced by degrading riffles and filling pools. Subsequent responses may be increases in width-to-depth ratio and slope.     

Ecosystem Consequences of Contrasting Flow Regimes in an Urban Effects Stream Mesocosm Study1

Abstract: A stream mesocosm experiment was conducted to study the ecosystem‐wide effects of two replicated flow hydrograph treatments programmed in an attempt to compare a simulated predevelopment condition to the theoretical changes that new development brings, while accounting for engineering design criteria for urban stormwater management. Accordingly, the treatments (three replicates each) differed in base flow between events and in the rise to, fall from, and duration of peak flow during simulated storm hydrographs, which were triggered by real rain events occurring outside over a 96‐day period from summer to fall, 2005. Incident irradiance, initial substrate quality, and water quality were similar between treatments. Sampling was designed to study the interactions among the treatment flow dynamics, sediment transport processes, streambed nutrients, and biotic structure and function. What appeared most important to the overall structure and function of the mesocosm ecosystems beyond those changes resulting from natural seasonality were (1) the initial mass of fines that infiltrated into the gravel bed, which had a persistent effect on nitrogen biogeochemistry and (2) the subsequent fine sediment accumulation rate, which was unexpectedly similar between treatments, and affected the structure of the macroinvertebrate community equally as the experiment progressed. Invertebrate taxa preferring soft beds dominated when the gravel was comprised of 5‐10% fines. The dominant invertebrate algal grazer had vacated the channels when fines exceeded 15%, but this effect could not be separated from what appeared to be a seasonal decline in insect densities over the course of the study. Neither hydrograph treatment allowed for scour or other potential for flushing of fines. This demonstrated the potential importance of interactions between hydrology and fine sediment loading dynamics on stream ecosystems in the absence of flows that would act to mobilize gravel beds.     

Assessment of Coarse Sediment Mobility in the Black Canyon of the Gunnison River,Colorado

The Gunnison River in the Black Canyon of the Gunnison National Park (BCNP) near Montrose, Colorado is a mixed gravel and bedrock river with ephemeral side tributaries. Flow rates are controlled immediately upstream by a diversion tunnel and three reservoirs. The management of the hydraulic control structures has decreased low-frequency, high-stage flows, which are the dominant geomorphic force in bedrock channel systems. We developed a simple model to estimate the extent of sediment mobilization at a given flow in the BCNP and to evaluate changes in the extent and frequency of sediment mobilization for flow regimes before and after flow regulation in 1966. Our methodology provides a screening process for identifying and prioritizing areas in terms of sediment mobility criteria when more precise systematic field data are unavailable. The model uses the ratio between reach-averaged bed shear stress and critical shear stress to estimate when a particular grain size is mobilized for a given reach. We used aerial photography from 1992, digital elevation models, and field surveys to identify individual reaches and estimate reach-averaged hydraulic geometry. Pebble counts of talus and debris fan deposits were used to estimate regional colluvial grain-size distributions. Our results show that the frequency of flows mobilizing river bank sediment along a majority of the Gunnison River in the BCNP has significantly declined since 1966. The model results correspond well to those obtained from more detailed, site-specific field studies carried out by other investigators. Decreases in the frequency of significant sediment-mobilizing flows were more pronounced for regions within the BCNP where the channel gradient is lower. Implications of these results for management include increased risk of encroachment of vegetation on the active channel and long-term channel narrowing by colluvial deposits. It must be recognized that our methodology represents a screening of regional differences in sediment mobility. More precise estimates of hydraulic and sediment parameters would likely be required for dictating quantitative management objectives within the context of sediment mobility and sensitivity to changes in the flow regime.     

Changes in Streambed Composition in Salmonid Spawning Habitat of the Elwha River during Dam Removal

One uncertainty associated with large dam removal is the level of downstream sediment deposition and associated short‐term biological effects, particularly on salmonid spawning habitat. Recent studies report downstream sediment deposition following dam removal is influenced by proximity to the source and river transport capacity. The impacts of dam removal sediment releases are difficult to generalize due to the relatively small number of dam removals completed, the variation in release strategies, and the physical nature of systems. Changes to sediment deposition and associated streambed composition in the Elwha River, Washington State, were monitored prior to (2010‐2011) and during (2012‐2014) the simultaneous removal of two large dams (32 and 64 m). Changes in the surface layer substrate composition during dam removal varied by year and channel type. Riffles in floodplain channels downstream of the dams fined and remained sand dominated throughout the study period, and exceeded levels known to be detrimental to incubating salmonids. Mainstem riffles tended to fine to gravel, but appear to be trending toward cobble after the majority of the sediment was released and transported through system. Thus, salmonid spawning habitats in the mainstem appear to have been minimally impacted while those in floodplain channels appear to have been severely impacted during dam removal.     

Response of a stream in disequilibrium to timber harvest

Timber was harvested on South Fork of Thomas Creek, White Mountains of Arizona, USA, for the first time in 1978–1979. This caused significant increases in annual flow volumes and annual instantaneous peak flows. North Fork remained untouched, but both streams were in disequilibrium before harvest time. Due to wetter years during the postharvest period, North Fork also experienced some flow increases, but the difference was not significant. Flow increases cause increased erosion in disequilibrium channels. While in South Fork channel cross sections enlarged by 10% since preharvest time, those in North Fork enlarged by only 2.5%. The number of knickpoints tripled in South Fork, which was about double that in North Fork. Knickpoint development resulted in destruction of the natural control structures (log steps and transverse gravel bars) in South Fork (47%), while in North Fork they increased by 23%. Knickpoints are scarps on the channel bed that have the appearance of gully headcuts. The tripling of the number of knickpoints signifies that adjustment processes of the bed profile are intensified drastically in South Fork. The geomorphic changes signify that due to increases in discharge, the extent of disequilibrium is exacerbated in South Fork. Yet, volumes of erosion are relatively small, as will be sediment volumes leaving the watershed at a given time, because of the stepwise sediment transport occurring in this ephemeral stream.     

MODELING METALS TRANSPORT AND SEDIMENT/WATER INTERACTIONS IN A MINING IMPACTED MOUNTAIN STREAM1

ABSTRACT: The U.S. Environmental Protection Agency (USEPA) Water Quality Analysis Simulation Program (WASP5) was used to model the transport and sediment/water interactions of metals under low flow, steady state conditions in Tenmile Creek, a mountain stream supplying drinking water to the City of Helena, Montana, impacted by numerous abandoned hard rock mines. The model was calibrated for base flow using data collected by USEPA and validated using data from the U.S. Geological Survey (USGS) for higher flows. It was used to assess metals loadings and losses, exceedances of Montana State water quality standards, metals interactions in stream water and bed sediment, uncertainty in fate and transport processes and model parameters, and effectiveness of remedial alternatives that include leaving contaminated sediment in the stream. Results indicated that during base flow, adits and point sources contribute significant metals loadings to the stream, but that shallow ground water and bed sediment also contribute metals in some key locations. Losses from the water column occur in some areas, primarily due to adsorption and precipitation onto bed sediments. Some uncertainty exists in the metal partition coefficients associated with sediment, significance of precipitation reactions, and in the specific locations of unidentified sources and losses of metals. Standards exceedances are widespread throughout the stream, but the model showed that remediation of point sources and mine waste near water courses can help improve water quality. Model results also indicate, however, that alteration of the water supply scheme and increasing base flow will probably be required to meet all water quality standards.     

SEDIMENT DISPERSION IN SALMON SPAWNING STREAMS: THE INFLUENCE OF FLOODS AND SALMON REDD CONSTRUCTION1

ABSTRACT: Magnetically tagged particles were used to investigate the effects of sockeye salmon (Oncorhynchus nerka) and floods on the dispersion of coarse bed material in the Stuart‐Takla region, British Columbia, Canada. The dominant annual sediment transporting event in the channels is the snowmelt flood events, with lesser activity usually accomplished during summer floods. Annually in August, the channel bed material is reworked by the Early Stuart sockeye salmon spawning, as the fish excavate the streambed to deposit and bury their eggs. These nesting cavities are called redds. Results from 67 tracer recovery experiments over five years were highly variable, subject to the magnitude of floods and the returning population of salmon. Overall, the depositional pattern from nival flood events usually demonstrated a high degree of clast mobilization, long travel distances (up to 150 m), and mean depths of burial up to 18 cm. Summer flood events showed somewhat lower rates of mobilization, distances of travel, and depths of burial. Although the fish did not move the tracers very far, their effect on the bed was generally quite pervasive ‐ up to 100 percent of the clasts were mobilized, and the depth of burial was considerable (mean burial depths up to 14 cm). The amount of vertical mixing of sediment by salmon was often on the same order of magnitude as flood events. The significant vertical mixing of sediments by the fish has important implications for the mobility of sediment in the stream. Since any armoring layer formed during high flows throughout the year is subject to the bioturbation of salmon, this suggests that the transport threshold in the creeks remains relatively low. Salmon likely play an integral role in the sediment transport dynamics and annual sediment budget of the lower reaches of these creeks.     

STABLE PROFILES OF PLUNGE BASINS1

The characteristics of scour holes were discussed including the problems created by them in relation to the hydraulic structures associated with their formation. The philosophy on the design and use of deflector buckets together with the need for plunge basins to dissipate the energy of the high velocity jets were reviewed. Laboratory observations were made to study the erosion of beds of gravel caused by water jets projected from spillway buckets. Flip buckets with 15, 30, 45 and 60 degrees exit angles were utilized. One-quarter inch and %-inch nominal size bed materials were used in the investigation. The gravel was placed in a large comprehensive scour basin to observe their behavior when subjected to the water jets. Besides the formula derived for the maximum depth of scour, a set of dimensionless equations were developed to describe the three-dimensional configuration of scour holes. The dimensions of stable plunge basins could be obtained from these profiles.     

THE VOLUME OF FINE SEDIMENT IN POOLS: AN INDEX OF SEDIMENT SUPPLY IN GRAVEL-BED STREAMS1

ABSTRACT: During waning flood flows in gravel-bed streams, finegrained bedload sediment (sand and fine gravel) is commonly winnowed from zones of high shear stress, such as riffles, and deposited in pools, where it mantles an underlying coarse layer. As sediment load increases, more fine sediment becomes available to fill pools. The volume of fine sediment in pools can be measured by probing with a metal rod, and, when expressed as the fraction (V*) of scoured residual pooi volume (residual pool volume with fine sediment removed), can be used as an index of the supply of mobile sediment in a stream channel. Mean values of V* were as high as 0.5 and correlated with qualitative evaluations of sediment supply in eight tributaries of the Trinity River, northwestern California. Fine-sediment volume correlated strongly with scoured pool volume in individual channels, but plots of V* versus pool volume and water surface slope revealed secondary variations in fines volume. In sediment-rich channels, V* correlated positively with scoured pool volume; in sediment-poor channels, V* correlated negatively with water-surface slope. Measuring fine sediment in pools can be a practical method to evaluate and monitor the supply of mobile sediment in gravel-bed streams and to detect and evaluate sediment inputs along a channel network.     

CHANNEL INSTABILITY IN THE LOESS AREA OF THE MIDWESTERN UNITED STATES1

ABSTRACT: The bess area of the midwestern United States contains thousands of miles of unstable stream channels that are undergoing system‐wide channel‐adjustment processes as a result of (1) modifications to drainage basins dating back to the turn of the 20th century, including land clearing and poor soil‐conservation practices, which caused the filling of stream channels, and consequently (2) direct, human modifications to stream channels such as dredging and straightening to improve drainage conditions and reduce the frequency of out‐of‐bank flows. Today, many of these channels are still highly unstable and threaten bridges, other structures, and land adjacent to the channels. The most severe, widespread instabilities are in western Iowa where a thick cap of bess and the lack of sand‐and gravel‐sized bed sediments in many channels hinders downstream aggradation, bed‐level recovery and the consequent reduction of bank heights, and renewed bank stability. In contrast, streams draining west‐central Illinois, east‐central Iowa, and other areas, where the bess cap is relatively thin and there are ample supplies of sand‐and gravel‐sized material, are closer to recovery. Throughout the region, however, channel widening by mass‐wasting processes is the dominant adjustment process.     

Comparison of Unsteady and Quasi‐Unsteady Flow Models in Simulating Sediment Transport in an Ephemeral Arizona Stream1

Hummel, Ryan, Jennifer G. Duan, and Shiyan Zhang, 2012. Comparison of Unsteady and Quasi‐Unsteady Flow Models in Simulating Sediment Transport in an Ephemeral Arizona Stream. Journal of the American Water Resources Association (JAWRA) 48(5): 987‐998. DOI: 10.1111/j.1752‐1688.2012.00663.x Abstract: Hydrodynamic and sediment transport models are useful engineering tools for predicting unsteady flood flow and sediment transport. Many models such as HEC‐RAS, HEC‐6, and IALLUVIAL apply quasi‐unsteady flow model, whereas others apply the unsteady flow model. It remains unknown if a quasi‐unsteady flow model is sufficiently accurate for simulating sediment transport in rapidly varied unsteady flood events, especially in ephemeral rivers in arid and semiarid regions. This study compared the quasi‐unsteady HEC‐RAS 4.1 model with one‐dimensional (1D) Finite Volume Method (FVM) based model in simulating flood flow and sediment transport in the Pantano Wash, a dryland river in the state of Arizona. The objective is to determine which sediment transport method is appropriate in predicting bed elevation changes in an ephemeral stream, Pantano Wash, and if an unsteady model is more accurate than a quasi‐unsteady flow model in predicting sediment transport. Results showed that the quasi‐unsteady HEC‐RAS model and the 1D FVM yielded similar results of bed degradation and aggradation for this dryland stream, although the FVM model predicted better flood hydrographs. Among the seven sediment transport formulas embedded in HEC‐RAS, Yang’s and Engelund‐Hansen’s equations gave the best matches with the field measurements for this particular case study.     

CHANNEL FORM AND STREAM ECOSYSTEM MODELS1

A system is proposed to classify running water habitats based on their channel form which can be considered in three different sedimentological settings: a cobble and boulder bed channel, a gravel bed channel, or a sand bed channel. Three physical factors (relief, lithology, and runoff) are selected as state factors that control all other interacting parameters associated with channel form. When these factors are integrated across the conterminous United States, seven distinct stream regions are evident, each representing a most probable succession of channel forms downstream from the headwaters to the mouth. Coupling these different channel profiles with typical biotic community structures usually associated with each of the channel types should result in considerable refinement of the applicability of the River Continuum Concept and other holistic ecosystem models by realizing the nonrandomness of the effects of geo-morphology on stream ecosystems. Thus, this regional perspective of streams should serve to make persons concerned with water resources more aware of the geographical considerations that affect their study areas.     

WAVE INDUCED FLOW AND TRANSPORT IN SEDIMENT BEDS1

ABSTRACT: The fate of contaminants in large water bodies is highly influenced by the transfer of flow and solutes across the water sediment interface. In this paper, an analytical model is presented where flow in both sediment bed and open channel is coupled at the interface through a boundary layer occupying the upper part of the sediment bed. The presence of this layer allows not only the capture of the inertia effects through a drag term in the generalized Darcy's equation, but also the specification of different soil parameters for the two porous zones. The flow is advective and driven by wave action along the water surface. The resulting system is solved for the pressure and flux in each sediment layer. The generated transport velocity fields are linked to a random walk simulation that is used to examine the trajectories of solute particles. Comparison of these trajectories against experimental tracer tests suggests a pattern very similar to the one attributed to the presence of surface mounds. The results clearly show the significance of the boundary layer and the drag term for soil with high permeability and the impact of both the thickness of the boundary layer and the length of the gravity wave relative to the depth of the water channel on the transport and exchange across the interface. The paper also examines the sensitivity of the mass exchange to the permeability of the two porous zones.     

ERODIBILITY OF URBAN BEDROCK AND ALLUVIAL CHANNELS,NORTH TEXAS1

ABSTRACT: Major erosion of urban stream channels is found in smaller basins in the North Texas study area with contributing drainage areas of less than ten square miles. Within these basins, four basic channel types are identified based on bed and bank lithologies: alluvial banks and bottoms, alluvial banks and gravel bottoms, alluvial banks with rock bottoms, and rock banks with rock bottoms. Most channels (75 percent) have alluvial banks with gravel or rock bottoms. Channel slopes are steep (.38 to.76 percent). Rock consists predominantly of shale and limestone. Channel cross sections are divided into the following four zones based on weathering, scour and entrainment mechanisms: soil zone, slake zone, rock zone and bed material zone. Erodibility of the channels is determined using multiple techniques including reach hydraulics and stream power computations, submerged jet testing, slab entrainment thresholds, and slake durability rates. Procedures are based on both empirical and modeled time series estimates of channel erosion. Field and modeled results support rates of erosion of up to four inches per year. Rates are tied to flow regime, climate, and type of channel bed and banks.     

SEDIMENT TRANSPORT AND CHANNEL MORPHOLOGY OF SMALL,FORESTED STREAMS1

This paper reviews sediment transport and channel morphology in small, forested streams in the Pacific Northwest region of North America to assess current knowledge of channel stability and morphology relevant to riparian management practices around small streams. Small channels are defined as ones in which morphology and hydraulics may be significantly influenced by individual clasts or wood materials in the channel. Such channels are headwater channels in close proximity to sediment sources, so they reflect a mix of hillslope and channel processes. Sediment inputs are derived directly from adjacent hillslopes and from the channel banks. Morphologically significant sediments move mainly as bed load, mainly at low intensity, and there is no standard method for measurement. The larger clastic and woody elements in the channel form persistent structures that trap significant volumes of sediment, reducing sediment transport in the short term and substantially increasing channel stability. The presence of such structures makes modeling of sediment flux in these channels — a potential substitute for measurement — difficult. Channel morphology is discussed, with some emphasis on wood related features. The problem of classifying small channels is reviewed, and it is recognized that useful classifications are purpose oriented. Reach scale and channel unit scale morphologies are categorized. A “disturbance cascade” is introduced to focus attention on sediment transfers through the slope channel system and to identify management practices that affect sediment dynamics and consequent channel morphology. Gaps in knowledge, errors, and uncertainties have been identified for future research.