Exposure to airborne allergens: a review of sampling methods

A number of methods are used to assess exposure to high-molecular weight allergens. In the occupational setting, airborne dust is often collected on filters using pumps, the filters are eluted and allergen content in the eluate analysed using immunoassays. Collecting inhalable dust using person-carried pumps may be considered the gold standard. Other allergen sampling methods are available. Recently, a method that collects nasally inhaled dust on adhesive surfaces within nasal samplers has been developed. Allergen content can be analysed in eluates using sensitive enzyme immunoassays, or allergen-bearing particles can be immunostained using antibodies, and studied under the microscope. Settling airborne dust can be collected in petri dishes, a cheap and simple method that has been utilised in large-scale exposure studies. Collection of reservoir dust from surfaces using vacuum cleaners with a dust collector is commonly used to measure pet or mite allergens in homes. The sampling methods differ in properties and relevance to personal allergen exposure. Since methods for all steps from sampling to analysis differ between laboratories, determining occupational exposure limits for protein allergens is today unfeasible. A general standardisation of methods is needed.     

Rapid one-step assays for on-site monitoring of mouse and rat urinary allergens

Allergy to rodent proteins is common among laboratory animal workers. Sensitive methods to measure exposure to these allergens have been developed. These assays are, however, expensive, time-consuming, and require a laboratory facility and methodological expertise. A simple method to screen for allergen spread, or to test whether hygiene standards are maintained, would be useful. Lateral flow immunoassays (LFIAs) are especially suited for field settings; the tests are simple and results are visible within minutes. LFIAs were developed for detection of the rodent urinary allergens Mus m 1 and Rat n 1. Pilot studies were performed in animal facilities in three countries using both extracts from airborne dust samples and samples collected by wiping surfaces. For comparison and determination of sensitivity, the concentrations of rodent urinary allergens in the samples were also measured using enzyme immunoassays (EIAs). The LFIAs for rat and mouse urinary allergens had a detection limit of 31 pg allergen per mL in a buffer system with purified allergen standards. Results of environmental dust extracts tested in LFIAs correlated well with levels obtained using EIAs. Spread of rodent allergens, or non-adherence to hygiene around laboratory animal facilities, may aggravate rodent allergy. Using a simple, sensitive one-step assay, allergens can be detected to prevent allergen exposure. The results reveal that the rapid assays are suited for on-site demonstration of exposure to rodent allergens, and thus, useful in occupational hygiene practice.     

A rapid lateral flow immunoassay for the detection of fungal alpha-amylase at the workplace

Fungal alpha-amylase is a flour supplement which is added to improve the quality of bakery products. Various studies have shown that exposure to this enzyme is an important risk factor for the development of bakers' allergy and this allergy is reported to be one of the most frequent causes of occupational asthma. A rapid assay was developed to monitor exposure to occupational allergens directly at the workplace. The sensitivity of the developed assay is 0.32 ng amylase mL(-1) in a buffer system with the commercially available alpha-amylase preparation Fungamyl 1600S as the standard. Initial validation tests (n = 33) were performed with airborne and settled dust from an industrial bakery. The new lateral flow immunoassay detected amylase in 22 of the 26 samples regarded as positive in an enzyme immunoassay, and was negative for all seven enzyme immunoassay-negative samples, while the four lateral flow immunoassay-negative/enzyme immunoassay-positive samples all had levels below 2 ng mL(-1). The sensitivity of 2 ng mL(-1) of the amylase lateral flow immunoassay is sufficient for first screening purposes and, therefore, this simple and rapid assay may allow direct on-site demonstration of work-related hazards of bio-allergen exposure. This would be particularly useful in occupational hygiene practice, especially in traditional or small-scale bakeries which lack the technological skills for testing the exposure to respiratory allergens.     

Exposure assessment in Beijing, China: biological agents, ultrafine particles, and lead

In this study, air samples were taken using a BioSampler and gelatin filters from six sites in Beijing: office, hospital, student dormitory, train station, subway, and a commercial street. Dust samples were also collected using a surface sampler from the same environments. Limulus amoebocyte lysate (LAL) and Glucatell assays were used to quantify sample endotoxin and (1,3)- ${\rm{\beta}} $ -d-glucan concentration levels, respectively. Enzyme-linked immunosorbent assay (ELISA) was used to measure the dust mite allergens (Der p 1 and Der f 1). Ultrafine particle and lead concentrations in these sampling sites were also measured using P-Trak and atomic absorption spectrometer, respectively. Analysis of variance (ANOVA) and linear regression analysis were used to analyze the concentration data. Higher culturable bacteria (12,639 CFU/m³) and fungi (1,806 CFU/m³) concentrations were observed for the train station and the subway system, respectively. For the rest of sampling sites, their concentrations were comparable to those found in western countries, ranging from 990 to 2,276 CFU/m³ for bacteria, and from 119 to 269 CFU/m³ for fungi. ANOVA analysis indicated that there were statistically significant differences between the culturable bacterial and fungal concentration levels obtained for different sites (p value = 0.0001 and 0.0047). As for dust allergens, endotoxin, and (1,3)-β -d-glucan, their concentrations also seemed to be comparable to those found in the developed countries. Airborne allergen concentrations ranged from 16 to 68 ng/m³. The dust-borne allergen concentration was observed to range from 0.063 to 0.327 ng/mg. As for endotoxin, the highest airborne concentration of 25.24 ng/m³ was observed for the commercial street, and others ranged from 0.0427 to 0.1259 ng/m³. And dust-borne endotoxin concentration ranged from 58.83 to 6,427.4 ng/mg. For (1,3)-β -d-glucan, the airborne concentration ranged from 0.02 to 1.2 ng/m³. Linear regression analyses showed that there existed poor correlations between those in airborne and dust-borne states (R²?=?0.002~0.43). In our study, the lowest ultrafine particle concentration about 5,203 pt/cm³ was observed in office and the highest was observed at the train station, up to 32,783 pt/cm³. Lead concentration was shown to range from 80 to 170 ng/mg with the highest also observed at the train station. The information provided in this work can be used to learn the general situation of relevant health risks in Beijing. And the results here suggested that when characterizing exposure both airborne and dust-borne as well as the environments should be considered.     

A simple method for the extraction of mutagens from airborne particles

Organic materials were extracted with acetone from filters of airborne particles by soaking, shaking, soxhletion, and sonication. These extracts were tested with and without S9 for mutagenicity using Ames assay and arabinose-resistant assay of Salmonella typhimurium. Among the extraction methods, soaking extract had the highest mutagenic activity followed by sonication, shaking, and soxhletion in both the assays. With the samples studied, it was concluded that soaking with acetone for 1/2 hr is the simplest and an efficient procedure for the extraction of mutagens from airborne particles.Results of cooperative investigation of NIOSH and West Virginia Agricultural and Forstry Experimental Station. Published with the approval of the Director of the West Virginia Agricultural and Forestry Experiment Station as Scientific Paper No. 1822.     

Fluorescence immunoassay using an optical fiber for determination of Dermatophagoides farinae (Der f1)

Immunoassay methods are generally used for measuring of allergenic substances. However, they need special facilities, skilled handling, and time-consuming procedure. In this work, a fiber-optic immunoassay system which could measure allergen by fluorescent intensities of immune complexes formed by allergens and fluorescently labeled antibodies was established. Immune complexes absorbed on the optical fiber probe surface, and excitation light was injected into the probe, then evanescent field is created in the proximity of the probe. The fluorophores were excited by the evanescent light, and fluorescence was detected by a photo diode. The target allergen detected by our system was Der f1 derived from Dermatophagoides farinae that is one of the house dust mite and major source of inhaled allergens. The fluorophore used labeling on detecting antibody was cyanine 5. The system enabled to detect and quantitatively determine of Der f1. The measurement range was from 0.24 to 250?ng/ml, and the result competes with ELISA. The measurement time was 16?min/sample. The immunoassay system was applied to measurement of Der f1 from actual dust samples. Calculated values of Der f1 showed good correlations between the fiber-optic fluoroimmunoassay and ELISA.     

Airborne rice pollen and pollen allergen in an agricultural field: aerobiological and immunochemical evidence

Grass pollens are well known among the health hazardous bioaerosols causing respiratory allergy. Being an important member of the grass family, the rice plants contribute a huge pollen load in agricultural fields during flowering. This results in a seasonal trigger of hay fever and respiratory allergy in the field workers and people living in the vicinity. Studies on the monitoring of airborne rice pollen and the intensity of the released allergen in agricultural fields are largely lacking. The aims of the present study were: (1) daily and hourly monitoring of airborne rice pollen in an agricultural field during the flowering period of plants in a winter crop season by using the Burkard 7-Day Volumetric Sampler and (2) the measurement of hourly airborne allergen intensity in the field in a peak rice pollen period by the double-antibody and chemiluminescence techniques to find out its relationship with the airborne rice pollen concentration. The monthly average concentration of rice pollen was 95 pollen m(-3) and the range of daily average pollen concentration was 0 to 386 pollen m(-3). A bimodal diurnal periodicity showed that the airborne rice pollen concentrations remained high at two different times of the day: between 08:00 h to 12:00 h and 14:00 h to 16:00 h. Deposition of airborne rice pollen allergen showed darker intensities on the immunostained tapes from the Burkard Sampler at the same two positions corresponding to higher pollen counts. These observations provided direct evidence of the allergenicity of airborne rice pollen in field conditions.     

Comparison of three sequential extraction procedures for partitioning of heavy metals in car park dusts

The aim of this study was to elucidate the amount of metal released at each step by using different extractants in three sequential extraction schemes for the partitioning of metal contents of car park deposited dust samples. For this purpose, three different sequential extraction procedures (SEP) were employed for the metal fractionation in car park dust samples collected from the campus of Erciyes University, Kayseri, Turkey. While two of the sequential extraction procedures contain five steps the other, namely the BCR sequential extraction scheme, has three steps. The first two methods fractionate metals to be exchangeable, bound to carbonates, bound to Mn oxides, bound to Fe oxides and bound to organic matter, and the BCR protocol fractionates the metals as acid soluble and exchangeable, reducible, and oxidisable. Determination of the metals Cd, Co, Cr, Cu, Fe, Mn, Ni, Pb and Zn was performed by flame atomic absorption spectrometry (FAAS). The results obtained by the three methods were compared and showed that the amount of metal released at each step of the leaching procedure depended both on the type of reagents used and the sequence in which they were applied. The most mobile elements were Cd, Pb and Zn which are metals potentially toxic to the environment and are also known to originate from traffic. The calculated enrichment factors for Cd and Pb were substantially high (73.5-187 and 18.4-27.5, respectively) and somewhat lower for Zn (5.1-6.8). These results confirm that they are important metal pollutants for car parks. Detection limits and recoveries were found in the range of 0.01-1.39 microg ml(-1) and 68-126%, respectively, for the metals studied and the three sequential extraction procedures.     

Passive airborne dust sampling to assess mite antigen exposure in farming environments

The aim of this study was to estimate mite antigen exposure in farming environments by passive sampling of airborne dust. Antigen concentrations were measured with enzyme immunoassays specific for three storage mites (SM): Acarus siro, Lepidoglyphus destructor, Tyrophagus putrescentiae and the house dust mite (HDM) Dermatophagoides pteronyssinus. Dust samples were collected with electrostatic dust fall collectors (EDCs) in three different areas of cattle farms. EDCs were placed in cow stables (working area), in changing rooms (transit area) and in different rooms of farmer dwellings (living area). Mite concentrations in the living area of farm homes were compared to those of urban homes. In dust samples from stables, antigens of all four mite species could be detected. The highest exposure level was to L. destructor (median 56.7 μg/m(2)), the lowest to A. siro (median 14.4 μg/m(2)). Mite concentrations of different species showed no correlation within the cow stables. In comparison to stables, the median mite concentrations in farm homes were significantly lower, ranging from below the detection limit to 1.5 μg/m(2). Antigens of SM were predominantly found in changing rooms and kitchens, and HDM antigens were mainly detected in bedrooms. Antigens of all mites were measured the least often in living rooms. T. putrescentiae was the most prevalent mite in all room types, and the exposure levels correlated strongly between different rooms. The number of SM positive samples in farm homes was considerably higher than in urban homes, while the percentage of HDM positive samples did not differ significantly.     

Influence of home characteristics on airborne and dustborne endotoxin and β-D-glucan

The aim of this study was to assess the associations between airborne and dustborne microbial contaminants (endotoxin and β-D-glucan) and estimate the effects of home characteristics on exposure levels of these microbial contaminants. Endotoxin and β-D-glucan concentrations in airborne inhalable particles, airborne PM1 (<1 μm) and vacuumed dust from 184 residential homes were determined using specific Limulus amebocyte assays. Home characteristics were recorded by visual inspection and questionnaires. Linear regression and correlation analyses were performed. Inhalable endotoxin correlated with dust endotoxin (r = 0.34, p < 0.001) and PM1 endotoxin (r = 0.33, p < 0.001). Inhalable β-D-glucan correlated with dust β-D-glucan (r = 0.18, p < 0.01), but not with PM1 β-D-glucan. Significant correlation was also found between PM1 and dust concentrations for endotoxin (r = 0.26, p < 0.001), but not for β-D-glucan. Multivariate regression analyses showed only one significant association between airborne contaminants and environmental characteristics: inhalable β-D-glucan was positively associated with relative humidity with an effect size (change in the dependent variable corresponding to a unit increase in the independent variable) of 2.32 and p < 0.05. In contrast, several associations were found between dust concentrations and environmental characteristics. Dust endotoxin was positively associated with temperature (2.87, p < 0.01) and number of inhabitants (2.76, p < 0.01), whereas dust β-D-glucan was inversely associated with the presence of dogs (-2.24, p < 0.05) and carpet (-3.05, p < 0.01) in the home. In conclusion, dustborne contaminants were more strongly affected by home characteristics than airborne contaminants. Furthermore, even though statistically significant, the correlations between airborne and dustborne contaminants were weak. This indicates that airborne concentrations cannot be reliably predicted based on dustborne concentrations.     

Characteristics of aerosol types during large-scale transport of air pollution over the Yellow Sea region and at Cheongwon,Korea, in 2008

Episodes of large-scale transport of airborne dust and anthropogenic pollutant particles from different sources in the East Asian continent in 2008 were identified by National Oceanic and Atmospheric Administration satellite RGB (red, green, and blue)-composite images and the mass concentrations of ground level particulate matter. These particles were divided into dust, sea salt, smoke plume, and sulfate by an aerosol classification algorithm. To analyze the aerosol size distribution during large-scale transport of atmospheric aerosols, aerosol optical depth (AOD) and fine aerosol weighting (FW) of moderate imaging spectroradiometer aerosol products were used over the East Asian region. Six episodes of massive airborne dust particles, originating from sandstorms in northern China, Mongolia, and the Loess Plateau of China, were observed at Cheongwon. Classified dust aerosol types were distributed on a large-scale over the Yellow Sea region. The average PM10 and PM2.5 ratio to the total mass concentration TSP were 70% and 15%, respectively. However, the mass concentration of PM2.5 among TSP increased to as high as 23% in an episode where dust traveled in by way of an industrial area in eastern China. In the other five episodes of anthropogenic pollutant particles that flowed into the Korean Peninsula from eastern China, the anthropogenic pollutant particles were largely detected in the form of smoke over the Yellow Sea region. The average PM10 and PM2.5 ratios to TSP were 82% and 65%, respectively. The ratio of PM2.5 mass concentrations among TSP varied significantly depending on the origin and pathway of the airborne dust particles. The average AOD for the large-scale transport of anthropogenic pollutant particles in the East Asian region was measured to be 0.42 ± 0.17, which is higher in terms of the rate against atmospheric aerosols as compared with the AOD (0.36 ± 0.13) for airborne dust particles with sandstorms. In particular, the region ranging from eastern China, the Yellow Sea, and the Korean Peninsula to the Korea East Sea was characterized by high AOD distributions. In the episode of anthropogenic polluted aerosols, FW averaged 0.63 ± 0.16, a value higher than that in the episode of airborne dust particles (0.52 ± 0.13) with sandstorms, showing that fine anthropogenic pollutant particles contribute greatly to atmospheric aerosols in East Asia.     

Effect of ultrasonic agitation on the release of copper, iron, manganese and zinc from soil and sediment using the BCR three-stage sequential extraction

An ultrasonic bath and an ultrasonic probe have been used to develop rapid versions of the three-stage Community Bureau of Reference (BCR, now the Standards, Measurement and Testing Programme) sequential extraction procedure. The effect of the ultrasonic treatments on the extraction of copper, iron, manganese and zinc from a sewage sludge-amended soil has been assessed. Recoveries similar to those of conventional shaking (i.e., conventional value, +/- 30%) could generally be obtained for copper, manganese and zinc, but not for the important matrix element iron. With the use of compromise sonication conditions, steps 1, 2 and 3 of the sequential extraction (excluding the hydrogen peroxide digestion in step 3, which was not performed with sonication) could be completed in 3, 5 and 1 min, respectively, using the ultrasonic probe, and in 3, 1 and 1 h, respectively, using the bath. The extraction procedures developed using the soil performed well when applied to lake sediment BCR CRM 601. Analyte partitioning was generally similar to that obtained with mechanical shaking, and overall metal recoveries were 84-98% of those obtained with the conventional BCR protocol, except for copper extracted with the probe (74%). Poorer performance (analyte recoveries, 58-104%) was obtained when the methods were applied to an intertidal sediment. This highlights the difficulty of developing a version of the BCR extraction, with ultrasonic assistance, which gives a performance equivalent to conventional shaking when applied to different substrates.     

Sampling and analysis considerations for the determination of hexavalent chromium in workplace air

Airborne hexavalent chromium (Cr[VI]) is a known human respiratory carcinogen and allergen. Workers in a variety of industries may be exposed to airborne hexavalent chromium, with exposures frequently occurring via inhalation and/or dermal contact. Analytical methods for the measurement of Cr(VI) compounds in workplace samples, rather than for the determination of total elemental chromium in workplace air, are often desired because exposure limit values for Cr(VI) compounds are much lower than for total Cr. For years, sampling and analytical test methods for airborne Cr(VI) have been investigated so as to provide means for occupational exposure assessment to this highly toxic species. Inter-conversion of trivalent chromium (Cr[III]) and Cr(VI) can sometimes occur during sampling and sample preparation, and efforts to minimize unwanted redox reactions involving these chromium valences have been sought. Because of differences in toxicity, there is also interest in the ability to differentiate between water-soluble and insoluble forms of Cr(VI), and procedures that provide solubility information concerning Cr(VI) compounds have been developed. This paper reviews the state of the art concerning the measurement of airborne Cr(VI) compounds in workplace aerosols and related samples.     

Real-time PCR detection of toxigenic Fusarium in airborne and settled grain dust and associations with trichothecene mycotoxins

Inhalation of immunomodulating mycotoxins produced by Fusarium spp. that are commonly found in grain dust may imply health risks for grain farmers. Airborne Fusarium and mycotoxin exposure levels are mainly unknown due to difficulties in identifying Fusarium and mycotoxins in personal aerosol samples. We used a novel real-time PCR method to quantify the fungal trichodiene synthase gene (tri5) and DNA specific to F. langsethiae and F. avenaceum in airborne and settled grain dust, determined the personal inhalant exposure level to toxigenic Fusarium during various activities, and evaluated whether quantitative measurements of Fusarium-DNA could predict trichothecene levels in grain dust. Airborne Fusarium-DNA was detected in personal samples even from short tasks (10-60 min). The median Fusarium-DNA level was significantly higher in settled than in airborne grain dust (p < 0.001), and only the F. langsethiae-DNA levels correlated significantly in settled and airborne dust (r(s) = 0.20, p = 0.003). Both F. langsethiae-DNA and tri5-DNA were associated with HT-2 and T-2 toxins (r(s) = 0.24-0.71, p < 0.05 to p < 00.01) in settled dust, and could thus be suitable as indicators for HT-2 and T-2. The median personal inhalant exposure to specific toxigenic Fusarium spp. was less than 1 genome m(-3), but the exposure ranged from 0-10(5) genomes m(-3). This study is the first to apply real-time PCR on personal samples of inhalable grain dust for the quantification of tri5 and species-specific Fusarium-DNA, which may have potential for risk assessments of inhaled trichothecenes.     

Comparison of DNA extraction methodologies used for assessing fungal diversity via ITS sequencing

Traditional methods of assessing fungal exposure have been confounded by a number of limiting variables. The recent utilization of molecular methods such as internal transcribed spacer (ITS) sequencing of ribosomal RNA genes has provided improved insight into the diversity of fungal bioaerosols in indoor, outdoor and occupational environments. However, ITS analyses may also be confounded by a number of methodological limitations. In this study, we have optimized this technology for use in occupational or environmental studies. Three commonly used DNA extraction methodologies (UltraClean Soil kit, High Pure PCR Template kit, and EluQuik/DNeasy kit) were compared in terms of sensitivity and susceptibility to PCR inhibitors in dust for three common fungal bioaerosols, Aspergillus versicolor, Rhizopus microsporus and Wallemia sebi. Environmental dust samples were then studied using each extraction methodology and results were compared to viable culture data. The extraction methods differed in terms of their ability to efficiently extract DNA from particular species of fungi (e.g. Aspergillus versicolor). In addition, the ability to remove PCR inhibitors from dust samples was most effective using the soil DNA extraction kit. The species composition varied greatly between ITS clone libraries generated with the different DNA extraction kits. However, compared to viable culture data, ITS clone libraries included additional fungal species that are incapable of growth on solid culture medium. Collectively, our data indicated that DNA extraction methodologies used in ITS sequencing studies of occupational or environmental dust samples can greatly influence the fungal species that are detected.     

Determination of germanium in urine and its usefulness for biomonitoring of inhalation exposure to inorganic germanium in the occupational setting

The present study aimed to assess whether urinary germanium concentration can be used as a biomarker of inhalation exposure to airborne dust from metallic germanium (Ge) or GeO2 in the occupational setting. A novel hydride generation-based method coupled with fow-injection graphite furnace atomic absorption spectrometry (HG/FI-GFAAS) was developed for the determination of urinary germanium. It was found that urinary germanium concentration could be reliably determined by a standard additions method after thorough digestion of the urine and careful pH adjustment of the digest. The limit of detection (LOD) in urine for the HG/FI-GFAAS method was 0.25 microg Ge L(-1). In Belgian control male subjects, the urinary germanium concentration was below this LOD. In 75 workers currently exposed to inorganic germanium compounds, respirable and inhalable concentrations of germanium in the aerosols were measured on Monday and Friday at the job sites using personal air samplers. Spot-urine samples were collected on the same days before and after the work shift. The germanium concentrations of respirable dust correlated very well with those of inhalable dust and represented 20% of the inhalable fraction. Workers exposed to metallic Ge dust were on average ten times less exposed to germanium than those whose exposure involved GeO2 (3.4 versus 33.8 microg Ge m(-3)). This difference was reflected in the urinary germanium concentrations (3.4 versus 23.4 microg Ge g(-1) creatinine). Regression analysis showed that the concentration of germanium in the inhalable fraction explained 42% of the post-shift urinary germanium concentration either on Monday or on Friday, whereas in a subgroup of 52 workers mainly exposed to metallic germanium dust 57% (r = 0.76) of the Monday post-shift urinary germanium was explained. Urinary elimination kinetics were studied in seven workers exposed to airborne dust of either metallic Ge or GeO2. The urinary elimination rate of germanium was characterised by half-times ranging from 8.2 to 18.1 h (on average 12 h 46 min). The present study did not allow discrimination between the germanium species to which the workers were exposed, but it showed fast urinary elimination kinetics for inhalation exposure to dust of metallic Ge and GeO2. It pointed out that urine samples taken at the end of the work shift can be used for biological monitoring of inorganic germanium exposure in the occupational setting.     

青藏高原典型城市拉萨市大气颗粒物污染源成分谱建立研究与特征分析

系统研究建立高原典型城市拉萨市开放源(土壤风沙尘、道路扬尘、施工扬尘、采矿扬尘),移动源(机动车尾气尘),固定源(工业烟粉尘、生物质燃烧尘及餐饮油烟)共3类8种大气颗粒物(PM_(2.5)、PM_(10))污染源化学成分谱。研究结果表明:开放源以地壳类元素为主,自然背景特征明显;移动源源成分谱中元素碳含量明显高于其他城市,在PM_(2.5)、PM_(10)源谱中分别占60.15%、51.86%,有机碳含量也相对较高,均超过20%;固定源中,牛粪和松柏枝两类生物质燃烧污染源的有机碳含量显著高于其他组分,工业烟粉尘中Ca远高于其他组分,在PM_(2.5)、PM_(10)源谱中分别占21.32%、21.21%。移动源、固定源源成分谱均显示出高原城市的独特特征。     

Evaluation of lot-to-lot repeatability and effect of assay media choice in the recombinant Factor C assay

Measurement of environmental endotoxin exposures is complicated by variability encountered using current biological assay methods arising in part from lot-to-lot variability of the Limulus-amebocyte lysate (LAL) reagents. Therefore, we investigated the lot-to-lot repeatability of commercially available recombinant Factor C (rFC) kits as an alternative to LAL. Specifically, we compared endotoxin estimates obtained from rFC assay of twenty indoor dust samples, using four different extraction and assay media, to endotoxin estimates previously obtained by Limulus amebocyte lysate (LAL) assay and amounts of 3-hydroxy fatty acids (3-OHFA) in lipopolysaccharide (LPS) using gas-chromatography mass spectroscopy (GC-MS). We found that lot-to-lot variability of the rFC assay kits does not significantly alter endotoxin estimates in house dust samples when performed using three of the four assay media tested and that choice of assay media significantly altered endotoxin estimates obtained by rFC assay of house dust samples. Our findings demonstrate lot-to-lot reproducibility of rFC assay of environmental samples and suggest that use of rFC assay performed with Tris buffer or water as the extraction and assay medium for measurement of endotoxin in dust samples may be a suitable choice for developing a standardized methodology.     

Assessment of particulate matter in the urban atmosphere: size distribution, metal composition and source characterization using principal component analysis

In this study, the size distribution of airborne particles and related heavy metals Co, Cd, Sn, Cu, Ni, Cr, Pb and V in two urban areas in Istanbul: Yenibosna and Goztepe, were examined. The different inhalable particles were collected by using a cascade impactor in eight size fractions (<0.4 μm, 0.4-0.7 μm, 1.1-2.1 μm, 2.1-3.3 μm, 3.3-4.7 μm, 4.7-5.8 μm, 5.8-9 μm and >9 μm) for six months at each station. Samples were collected on glass fiber filters and filters were extracted and analyzed using ICP-MS. Log-normal distributions showed that the particles collected at the Yenibosna site have a smaller size compared to the Goztepe samples and the size distribution of PM was represented the best by the tri-modal. The average total particle concentrations and standard deviations were obtained as 67.7 ± 17.0 μg m(-3) and 82.1 ± 21.2 μg m(-3), at the Yenibosna and G?ztepe sites, respectively. The higher metal rate in fine and medium coarse PM showed that the anthropogenic sources were the most significant pollutant source. Principal component analysis identified five components for PM namely traffic, road dust, coal and fuel oil combustion, and industrial.     

Mineralogy of Atmospheric Suspended Dust in Three Indoor And One Outdoor Location in Oman

The aim of this work is to characterize the mineral phases present in the atmosphere at three locations in northern Oman. Samples of atmospheric particles were collected using a high volume sampler. Three indoor and one outdoor location were chosen in this investigation. Sampling locations included a residential house located nearby the cement plant, a residential house located nearby a refinery plant, and a residential house located at Al-Suwayq residential area. Indoor air was sampled from these three houses. Moreover, for the Al-Suwayq residential house, sampling was also taken outside the house for comparison. The dust samples were analysed for their microanalysis characterization and their mineral contents as well. The microanalysis enabled us to identify the metals present in the particles. Furthermore, the mineralogical analysis of the sample filters showed the presence of quartz as the principal phase inside the house of Al-Suwayq, whereas quartz, dolomite, and gypsum were common phases outside the house. In the residential house nearby the cement plant, it was found that calcite, quartz, dolomite and goethite were the principal phases whereas the particles collected from the house nearby the refinery composed primarily of dolomite and calcite. The airborne dust collected at the refinery and Al-Suwayq were probably sourced in the natural environment and mobilised by natural processes. However, at the cement factory the crushing and grinding of limestone during the industrial process has contributed significantly to the airborne dust load. Generally, the information obtained in this study will be invaluable as no data for the mineral content of atmospheric dust existed in the Oman.