Adsorption of basic dye from aqueous solution onto fly ash

The fly ash treated by H₂SO₄ was used as a low-cost adsorbent for the removal of a typical dye, methylene blue, from aqueous solution. An increase in the specific surface area and dye-adsorption capacity was observed after the acid treatment. The adsorption isotherm and kinetics of the treated fly ash were studied. The experimental results were fitted using Langmuir and Freundlich isotherms. It shows that the Freundlich isotherm is better in describing the adsorption process. Two kinetic models, pseudo-first order and pseudo-second order, were employed to analyze the kinetic data. It was found that the pseudo-second-order model is the better choice to describe the adsorption behavior. The thermodynamic study reveals that the enthalpy (ΔH⁰) value is positive (5.63 kJ/mol), suggesting an endothermic nature of the adsorption.     

Adsorption characterization of Pb(II) and Cu(II) ions onto chitosan-tripolyphosphate beads: Kinetic,equilibrium and thermodynamic studies

Chitosan-tripolyphosphate (CTPP) beads were synthesized, characterized and were used for the adsorption of Pb(II) and Cu(II) ions from aqueous solution. The effects of initial pH, agitation period, adsorbent dosage, different initial concentrations of heavy metal ions and temperature were studied. The experimental data were correlated with the Langmuir, Freundlich and Dubinin-Radushkevich isotherm models. The maximum adsorption capacities of Pb(II) and Cu(II) ions in a single metal system based on the Langmuir isotherm model were 57.33 and 26.06 mg/g, respectively. However, the beads showed higher selectivity towards Cu(II) over Pb(II) ions in the binary metal system. Various thermodynamic parameters such as enthalpy (ΔH°), Gibbs free energy (ΔG°) and entropy (ΔS°) changes were computed and the results showed that the adsorption of both heavy metal ions onto CTPP beads was spontaneous and endothermic in nature. The kinetic data were evaluated based on the pseudo-first and -second order kinetic and intraparticle diffusion models. Infrared spectra were used to elucidate the mechanism of Pb(II) and Cu(II) ions adsorption onto CTPP beads.     

Green coconut shells applied as adsorbent for removal of toxic metal ions using fixed-bed column technology

This study applies green coconut shells as adsorbent for the removal of toxic metal ions from aqueous effluents using column adsorption. The results show that a flow rate of 2 mL/min and a bed height of 10 cm are most feasible. Furthermore, larger amounts of effluent can be treated for removal of single ions. The breakthrough curves for multiple elements gave the order of adsorption capacity: Cu⁺² > Pb⁺² > Cd⁺² > Zn⁺² > Ni⁺². Real samples arising from the electroplating industry can be efficiently handled.     

Prediction of metal-adsorption behaviour in the remediation of water contamination using indigenous microorganisms

In recent years, the adsorption of heavy metal cations onto bacterial surfaces has been studied extensively. This paper reports the findings of a study conducted on the heavy metal ions found in mine effluents from a mining plant where Co²⁺ and Ni²⁺ bearing minerals are processed. Heavy metal ions are reported to be occasionally present in these mine effluents, and the proposed microbial sorption technique offers an acceptable solution for the removal of these heavy metals. The sorption affinity of microorganisms for metal ions can be used to select a suitable microbial sorbent for any particular bioremediation process. Interactions of heavy metal ions (Co²⁺ and Ni²⁺) and light metal ions (Mg²⁺ and Ca²⁺) with indigenous microbial cells (Brevundimonas spp., Bacillaceae bacteria and Pseudomonas aeruginosa) were investigated using the Langmuir adsorption isotherm, pseudo second-order reaction kinetics model and a binary-metal system. Equilibrium constants and adsorption capacities derived from these models allowed delineation of the effect of binding affinity and metal concentration ratios on the overall adsorption behaviour of microbial sorbents, as well as prediction of performance in bioremediation systems. Although microbial sorbents used in this study preferentially bind to heavy metal ions, it was observed that higher concentrations (>90 mg/?) of light metal ions in multi-metal solutions inhibit the adsorption of heavy metal ions to the bacterial cell wall. However, the microbial sorbents reduced Ni²⁺ levels in the mine-water used (93–100% Ni²⁺ removal) to below the maximum acceptable limit of 350 μg/?, established by the South African Bureau of Standards. Competition among metal ions for binding sites on the biomaterial surface can occur during the bioremediation process, but microbial sorption affinity for heavy metal ions can enhance their remediation in dilute (<5 mg/? heavy metal) wastewaters.     

Evaluation of a low-cost adsorbent for removal of toxic metal ions from wastewater of an electroplating factory

In this study, sugar cane residue or bagasse was used for removal of toxic metal ions from wastewater of an electroplating factory located in northeast Brazil. Prior acid treatment increased the adsorption efficacies in batch wise experiments. The microstructure of the material before and after the treatment was investigated by X-ray diffraction, infrared spectroscopy and scanning electron microscopy. Column operations showed that removals of Cu²⁺, Ni²⁺ and Zn²⁺ from wastewater (in the absence of cyanide) were 95.5%, 96.3.0%, and 97.1%, respectively. Regeneration of the adsorbent obtained in acid indicated that the efficiencies decreased only after the fourth cycle of re-use. Acid-treated sugar cane bagasse can be considered a viable alternative to common methods to remove toxic metal ions from aqueous effluents of electroplating industries.     

Adsorptive removal of Cd(II) and Pb(II) ions from aqueous solutions by using Turkish illitic clay

The ability of Turkish illitic clay (TIC) in removal of Cd(II) and Pb(II) ions from aqueous solutions has been examined in a batch adsorption process with respect to several experimental conditions including initial solution pH, contact time, initial metal ions concentration, temperature, ionic strength, and TIC concentration, etc. The characterization of TIC was performed by using FTIR, XRD and XRF techniques. The maximum uptake of Cd(II) (11.25 mg g⁻¹) and Pb(II) (238.98 mg g⁻¹) was observed when used 1.0 g L⁻¹ of TIC suspension, 50 mg L⁻¹ of initial Cd(II) and 250 mg L⁻¹ of initial Pb(II) concentration at initial pH 4.0 and contact time of 240 min at room temperature. The experimental data were analyzed by the Langmuir, Freundlich, Temkin and Dubinin Radushkevich (D-R) isotherm models. The monolayer adsorption capacity of TIC was found to be 13.09 mg g⁻¹ and 53.76 mg g⁻¹ for Cd(II) and Pb(II) ions, respectively. The kinetics of the adsorption was tested using pseudo-first-order, pseudo-second-order, Elovich and intraparticle diffusion models. The results showed that the adsorption of Cd(II) and Pb(II) ions onto TIC proceeds according to the pseudo-second-order model. Thermodynamic parameters including the Gibbs free energy (ΔG), enthalpy (ΔH), and entropy (ΔS) changes indicated that the present adsorption process was feasible, spontaneous and endothermic in the temperature range of 5–40 °C.     

Assessment of the spring water quality in The Shoubak area,Jordan

The present study investigates the physical, chemical, and biological characteristics of spring water samples in Shoubak area in the southern Jordan. The samples were collected from May 2004 to May 2005. All samples were analyzed for temperature, conductivity, dissolved oxygen, pH, major cations (Ca²⁺, Mg²⁺, K⁺, Na⁺), major anions (Cl⁻, NO₃⁻, HCO₃⁻, SO₄²⁻, PO₄³⁻, F⁻), and trace metals (Fe²⁺, Al³⁺, Mn²⁺, Cu²⁺, Cr³⁺, Ni²⁺, Zn²⁺, Pb²⁺, Cd²⁺). Water quality for available springs showed high salinity through long period of contact with rocks. The ion concentrations in the water samples were from dissolution of carbonate rocks and ion exchange processes in clay. The general chemistry of water samples was typically of alkaline earth waters with prevailing bicarbonate chloride. Some springs showed elevated nitrate and sulfate contents which could reflect to percolation from septic tanks, cesspools, and agricultural practices. The infiltration of wastewater from cesspools and septic tanks into groundwater is considered the major source of water pollution. The results showed that there were great variations among the analyzed samples with respect to their physical, chemical and biological parameters, which lie below the maximum permissible levels of the Jordanian and WHO drinking water standards. The results indicate that the trace metals of spring’s water of Shoubak area do not generally pose any health or environmental problems. Factor analysis was used to identify the contributers to water quality. The first factor represents major contribution from anthropogenic activities, while the second one represents major contribution from natural processes.     

Zeolite formation from coal fly ash and heavy metal ion removal characteristics of thus-obtained Zeolite X in multi-metal systems

Zeolitic materials have been prepared from coal fly ash as well as from a SiO₂–Al₂O₃ system upon NaOH fusion treatment, followed by subsequent hydrothermal processing at various NaOH concentrations and reaction times. During the preparation process, the starting material initially decomposed to an amorphous form, and the nucleation process of the zeolite began. The carbon content of the starting material influenced the formation of the zeolite by providing an active surface for nucleation. Zeolite A (Na-A) was transformed into zeolite X (Na-X) with increasing NaOH concentration and reaction time. The adsorption isotherms of the obtained Na-X based on the characteristics required to remove heavy ions such as Ni²⁺, Cu²⁺, Cd²⁺ and Pb²⁺ were examined in multi-metal systems. Thus obtained experimental data suggests that the Langmuir and Freundlich models are more accurate compared to the Dubinin–Kaganer–Radushkevich (DKR) model. However, the sorption energy obtained from the DKR model was helpful in elucidating the mechanism of the sorption process. Further, in going from a single- to multi-metal system, the degree of fitting for the Freundlich model compared with the Langmuir model was favored due to its basic assumption of a heterogeneity factor. The Extended-Langmuir model may be used in multi-metal systems, but gives a lower value for equilibrium sorption compared with the Langmuir model.     

Loofa egyptiaca as a novel adsorbent for removal of direct blue dye from aqueous solution

In this paper, Loofa egyptiaca (LE), an agricultural plant cultivated in Egypt, was used to prepare low-cost activated carbon (LE_C1 and LE_C2) adsorbents. The adsorbents (LE, LE_C1 and LE_C2) were evaluated for their ability to remove direct blue 106 dye from aqueous solutions. Batch mode experiments were conducted using various parameters such as pH, contact time, dye concentration and adsorbent concentration. The surface chemistry of LE, LE_C1 and LE_C2 was analyzed by scanning electron microscopy (SEM). The experimental data were examined using Langmuir, Freundlich, Temkin and Harkins–Jura isotherms. The results showed that the adsorption of direct blue 106 was maximal at the lowest value of pH (pH = 2). Removal efficiency was increased with an increase in dye concentration and a decrease in amount of adsorbent. Maximum adsorption capacity was found to be 57.14, 63.3 and 73.53 mg/g for LE, LE_C1 and LE_C2 respectively. Kinetics were also investigated using pseudo-first-order, pseudo-second-order and intra-particle diffusion models. The experimental data fitted very well with the pseudo-first-order and pseudo-second-order kinetic models. The results indicate that LE, LE_C1 and LE_C2 could be employed as adsorbents for the removal of direct blue dye from aqueous solutions.     

Physicochemical characterization of hydroxyapatite and its application towards removal of nitrate from water

A laboratory study was conducted to investigate the efficiency of hydroxyapatite (HAP) towards removal of nitrate from synthetic nitrate solution. In the present research HAP synthesized from egg-shell was characterized using SEM, XRD, FTIR and TGA–DSC. The removal of nitrate was 96% under neutral conditions, using 0.3 g of adsorbent in 100 mL of nitrate solution having an initial concentration of 100 mg/L. An adsorption kinetic study revealed that the adsorption process followed first order kinetics. Adsorption data were fitted to a linearly transformed Langmuir isotherm with correlation coefficient (R²) > 0.98. Thermodynamic parameters were also calculated to study the effect of temperature on the removal process. In order to understand the adsorption type, equilibrium data were tested with the Dubinin–Radushkevich isotherm. The process was rapid and equilibrium was established within the first 40 min.     

Water quality indices appraisal and health risk assessment of nitrate,mercury and lead in water distribution network: A case study of Robat Karim in Tehran,Iran

Groundwater is a basic source of drinking water supply for urban and rural areas. This is especially the case for communities located in arid and semi-arid regions that rely on groundwater for drinking purposes. The present study set out to assess the potential health impacts of water impurities and to investigate the qualitative status of drinking water in Robat Karim rural areas, located in southwest Tehran, Iran. A total of 66 samples were collected from the water distribution network of 11 villages (33 sampling points, on two occasions) during September 2020 and were tested in terms of the most common quality parameters such as pH, mercury (Hg), lead (Pb), copper (Cu), zinc (Zn), chloride (Cl^–), chlorate (ClO₃^–), nitrite (NO₂^–), nitrate (NO₃^–), and flouride (F^–). Multiple methods and indexes including water quality index (WQI), hazard quotient (HQ), and hazard index (HI), were worked out to assess the quality of water and health risk assessment of NO₃^– Pb²⁺ and Hg²⁺. The results revealed that 33% and 90% of sampling sites have significantly high nitrate and total hardness (TH) concentrations, exceeding the maximum permissible limits set by World Health Organization (WHO; 50 and 200 mg/L, respectively). Furthermore, five sampling points exhibited poor WQIs mainly related to NO₃^– and TH. HQ values higher than 1 for nitrate were noticed in most sampling locations. Except for one sampling point, the HQ obtained for Pb²⁺ and Hg²⁺ were below 1 indicating no obvious health hazard. This study represents that children and infants are at higher risk of chronic toxicity by excess NO₃^– intake. The health hazard that is yet imposed on the community by NO₃^– necessitates regular monitoring of drinking water, the use of advanced technologies to purify water or otherwise alternative resources should be proposed.     

Evaluation of biogas production from seaweed in batch tests and in UASB reactors combined with the removal of heavy metals

Seaweed can be anaerobically digested for the production of energy-rich methane. However, the use of seaweed digestate as a fertilizer may be restricted because of the high heavy metal content especially cadmium. Reducing the concentration of heavy metals in the digestate will enable its use as a fertilizer. In this laboratory-scale study, the potential of seaweed and its leachate in the production of methane were evaluated in batch tests. The effect of removing the heavy metals from seaweed leachate was evaluated in both batch test and treatment in an upflow anaerobic sludge blanket (UASB) reactor. The heavy metals were removed from seaweed leachate using an imminodiacetic acid (IDA) polyacrylamide cryogel carrier. The methane yield obtained in the anaerobic digestion of seaweed was 0.12 N l CH₄/g VS_added. The same methane yield was obtained when the seaweed leachate was used for methane production. The IDA-cryogel carrier was efficient in removing Cd²⁺, Cu²⁺, Ni²⁺ and Zn²⁺ ions from seaweed leachate. The removal of heavy metals in the seaweed leachate led to a decrease in the methane yield. The maximum sustainable organic loading rate (OLR) attained in the UASB reactor was 20.6 g tCOD/l/day corresponding to a hydraulic retention time (HRT) of 12 h and with a total COD removal efficiency of about 81%. Hydrolysis and treatment with IDA cryogel reduced the heavy metals content in the seaweed leachate before methane production. This study also demonstrated the suitability of the treatment of seaweed leachate in a UASB reactor.     

Possible Utilization of Silica Gel Sludge for the Removal of Phenol from Aqueous Solutions: Laboratory Studies

This paper discusses the adsorption capacity of silica gel sludge for phenol removal from aqueous solution. Kinetic experiments showed that phenol adsorption was completed after 2 h. Adsorption isotherms were measured for phenol from aqueous solution onto silica gel sludge under various pHs and temperatures. Results showed that the adsorption capacities for phenol was increased as pH decreased from 6.5 to 2. Temperature also was found to affect the adsorption isotherm. As temperature increases from 30 to 50°C, the adsorption capacity increases. The adsorption equilibrium of phenol on silica gel sludge was described by the linear Freundlich and Langmuir models. Furthermore, results showed that the isotherm parameters fit both linearized Langmuir and Freundlich adsorption isotherms. The Freundlich and Langmuir parameters at optimum pH was found as K _f=2.89, 1/n=0.23 and K _d=22.0, q _m=7.98, respectively. Whereas, for those at optimum temperature it was observed as K _f=2.87, 1/n=0.16 and K _d=20.93, q _m=7.91, respectively.     

Equilibrium studies of copper ion adsorption onto palm kernel fibre

The equilibrium sorption of copper ions from aqueous solution using a new adsorbent, palm kernel fibre, has been studied. Palm kernel fibre is obtained in large amounts as a waste product of palm oil production. Batch equilibrium studies were carried out and system variables such as solution pH, sorbent dose, and sorption temperature were varied. The equilibrium sorption data was then analyzed using the Langmuir, Freundlich, Dubinin–Radushkevich (D–R) and Temkin isotherms. The fit of these isotherm models to the equilibrium sorption data was determined, using the linear coefficient of determination, r², and the non-linear Chi-square, χ² error analysis.The results revealed that sorption was pH dependent and increased with increasing solution pH above the pH_PZC of the palm kernel fibre with an optimum dose of 10 g/dm³. The equilibrium data were found to fit the Langmuir isotherm model best, with a monolayer capacity of 3.17 × 10^?4 mol/g at 339 K. The sorption equilibrium constant, K_a, increased with increasing temperature, indicating that bond strength between sorbate and sorbent increased with temperature and sorption was endothermic. This was confirmed by the increase in the values of the Temkin isotherm constant, B₁, with increasing temperature. The Dubinin–Radushkevich (D–R) isotherm parameter, free energy, E, was in the range of 15.7–16.7 kJ/mol suggesting that the sorption mechanism was ion exchange. Desorption studies showed that a high percentage of the copper was desorbed from the adsorbent using acid solutions (HCl, HNO₃ and CH₃COOH) and the desorption percentage increased with acid concentration. The thermodynamics of the copper ions/palm kernel fibre system indicate that the process is spontaneous and endothermic.     

Phenol removal from aqueous environments by natural & chemically modified kaolin clay

Natural, acid and base modified kaolin clays were studied for the sake of phenol and 4-chlorophenol removal from aqueous environments and their application to real ground and industrial wastewater samples. Scanning electron microscope (SEM), infrared spectroscopy (IR), X-ray diffraction (XRD), Thermo Gravimetric Analysis (TGA), Differential Thermal Analysis (DTA), and Surface area analysis were employed for characterization of the adsorbents microstructure. Operating factors such as adsorbent dose, solution pH, initial phenol concentration, and contact time were studied. The experimental data displayed that the increase of the adsorbent dose, contact time, and pH value from 2 to 7 increases the efficiency of the removal process. Optimal conditions for phenolic removal were; contact time of 300 min, primary phenol solution of 25 mg/L, pH 7 and 2.5 g/L as an appropriate adsorbent dose using crude (natural), acid modified and base modified kaolin clays. The higher phenolic removal efficiencies were obtained at 5 mg/L as 90, 97, 96.2%, respectively, for the adsorbents in the previously mentioned order. The adsorption capacity in the removal of phenol and 4-chlorophenol were 7.481 and 4.195, 8.2942 and 3.211, and 8.05185 and 18.565 mg/g, respectively, for the adsorbents in the same mentioned order. The adsorption equilibrium data were fitted and analyzed with four isotherm models, namely, Langmuir, Freundlich, Temkin, and Dubinin–Radushkevich isotherm equations. The adsorption process of phenol on studied adsorbents was exothermic, spontaneous and thermodynamically favorable proved by the negative values of their thermodynamic parameters ΔH° and ΔG°. The correlation coefficient (R²) for all concentrations was higher than 0.94, which indicates that in the studied system, the data suitably fit the first-order kinetics. The % desorption capacity was amounted to 96%, 91.11%, and 87.06% of adsorbed phenol, respectively, for the adsorbents in the previous order using 0.1N NaOH and 10% V/V ethanol solutions as eluents at 25°C, indicating the reusability of the adsorbents. Kaolin and its modified forms can be introduced as eco-friendly and low-cost adsorbents in water remediation implementation.     

Fly ash for the treatment of Zn(II) rich effluents

Summary The ability of fly ash to remove Zn(II) from water by adsorption has been tested at different concentrations, temperatures and pH of the solution. It was found that low adsorbate concentration, small particle size of adsorbent and higher temperature favoured the removal of Zn(II) from aqueous solution. The Langmuir isotherm was used to represent the equilibrium data at different temperatures. The apparent heat of adsorption has been found to be 17.325 Kcal mol^–1, which indicates the process to be endothermic. The uptake of Zn(II) is diffusion controlled and the mass transfer coefficient is 3.56 × 10^–5 cm s ^–1.The maximum removal was noted at pH 7.5. Dr V.N. Singh is Professor and Head of the Department of Applied Chemistry, Dr A.K. and Prof. D.P. Singh are members of the Department of Mining Engineering; all are situated in the Institute of Technology at Banaras Hindu University.     

Adsorption of carbon dioxide using impregnated activated carbon promoted by Zinc

The effect of impregnation of activated carbon with Cr₂O and Fe₂O₃ and promotion by Zn²⁺ on its adsorptive properties of carbon dioxide was studied using a volumetric adsorption apparatus at ambient temperature and low pressures. Slurry and solution impregnation methods were used to compare CO₂ capture capacity of the impregnated activated carbon promoted by Zinc. The obtained adsorption isotherms showed that amount of CO₂ adsorbed on the samples impregnated by Cr₂O was increased about 20% in compare to raw activated carbon. The results also showed that Fe₂O₃ was not an effective impregnating species for activated carbon modification. Moreover slurry impregnation method showed higher CO₂ adsorption capacity in comparison with solution impregnation method. Samples prepared by co-impregnation of two metal species showed more adsorption capacity than samples impregnated by just one metal species individually. Washing the impregnated samples by metal oxide resulted in 15% increase in CO₂ adsorption capacities of activated carbons which can be attributed to the metal oxides removal covering the adsorption surface. Decreasing impregnation temperature from 95 to 25 °C in solution method showed a significant increase in CO₂ adsorption capacity. Sips equation was found a suitable model fitting to the adsorption data in the range studied.     

Adsorption of malachite green and chrysoidine-Y by Sn-pillared clay

The aim of this research was to pillar the bentonite clay (Bt) with polyhydroxy tin chloride. The synthesized Tin-pillared interlayer clay (Sn-PILC) was characterized using X-ray diffraction (XRD), Fourier Transform Infrared spectra (FT-IR), Brunauer-Emmer Teller (BET) analysis, Thermogravimetric analysis (TGA), and Scanning Electron Microscopy (SEM). Adsorption capacity of raw-Bt and tin pillared interlayer clay (Sn-PILC) was examined for two dyes, namely, Malachite Green (MG) and Chrysoidine-Y (CY) from their aqueous solutions. The effects of physicochemical parameters like solution pH, dose, and dye concentration were investigated. The maximum adsorption efficiency at equilibrium dye concentration for Sn-PILC was 66.229 mg g^–1 for MG and 63.792 mg g^–1 for CY. Sn-PILC obeyed Langmuir isotherm for both the dyes whereas raw-Bt followed Freundlich isotherm. On the other hand, both adsorbents followed PFO as well as PSO kinetic model, indicating physisorption assisted by chemisorption. Thermodynamic studies were performed to determine the adsorption behavior of Sn-PILC for both the dyes. Regeneration studies revealed 80% efficiency up-to five adsorption-desorption cycles.     

Utilization of waste product (tamarind seeds) for the removal of Cr(VI) from aqueous solutions: Equilibrium, kinetics, and regeneration studies

In the present study, an adsorbent was prepared from tamarind seeds and used after activation for the removal of Cr(VI) from aqueous solutions. The tamarind seeds were activated by treating them with concentrated sulfuric acid (98% w/w) at a temperature of 150 °C. The adsorption of Cr(VI) was found to be maximum at low values of initial pH in the range of 1–3. The adsorption process of Cr(VI) was tested with Langmuir, Freundlich, Redlich–Peterson, Koble–Corrigan, Tempkin, Dubinin–Radushkevich and Generalized isotherm models. Application of the Langmuir isotherm to the system yielded a maximum adsorption capacity of 29.7 mg/g at an equilibrium pH value ranging from 1.12 to 1.46. The adsorption process followed second-order kinetics and the corresponding rate constants obtained were 2.605 × 10⁻³, 0.818 × 10⁻³, 0.557 × 10⁻³ and 0.811 × 10⁻³ g/mg min⁻¹ for 50, 200, 300 and 400 mg/L of initial Cr(VI) concentration, respectively. The regenerated activated tamarind seeds showed more than 95% Cr(VI) removal of that obtained using the fresh activated tamarind seeds. A feasible solution is proposed for the disposal of the contaminants (acid and base solutions) containing high concentrations of Cr(VI) obtained during the regeneration (desorption) process.     

Biosorption of Cu and Zn from aqueous solutions by dried marine green macroalga Chaetomorpha linum

The biosorption of the heavy metals Cu²⁺ and Zn²⁺ by dried marine green macroalga (Chaetomorpha linum) was investigated. The biosorption capacities of the dried alga for copper and zinc were studied at different solution pH values (2–6), different algal particle sizes (100–800 μm) and different initial metal solution concentrations (0.5–10 mM). An optimum pH value of 5 was found suitable for both metal ions biosorption for both metal ions. At the optimum particle size (100–315 μm), biosorbent dosage (20 g/l) and initial solution pH (pH 5), the dried alga produced maximum copper and zinc uptakes values (q_max) of 1.46 and 1.97 mmol/g respectively (according to the Langmuir model). The kinetic data obtained at different initial metal concentrations indicated that the biosorption rate was fast and most of the process was completed within 120 min. This study illustrated an alternative technique for the management of unwanted biological materials using processed algal material. C. linum is one of the fast-growing marine algae in the lake of Tunis and could be utilized as a biosorbent for the treatment of Cu²⁺ and Zn²⁺ contaminated wastewater streams.