Effects of chemical composition of fly ash on efficiency of metal separation in ash-melting of municipal solid waste

In the process of metal separation by ash-melting, Fe and Cu in the incineration residue remain in the melting furnace as molten metal, whereas Pb and Zn in the residue are volatilized. This study investigated the effects of the chemical composition of incineration fly ash on the metal-separation efficiency of the ash-melting process. Incineration fly ash with different chemical compositions was melted with bottom ash in a lab-scale reactor, and the efficiency with which Pb and Zn were volatilized preventing the volatilization of Fe and Cu was evaluated. In addition, the behavior of these metals was simulated by thermodynamic equilibrium calculations. Depending on the exhaust gas treatment system used in the incinerator, the relationships among Na, K, and Cl concentrations in the incineration fly ash differed, which affected the efficiency of the metal separation. The amounts of Fe and Cu volatilized decreased by the decrease in the molar ratio of Cl to Na and K in the ash, promoting metal separation. The thermodynamic simulation predicted that the chlorination volatilization of Fe and Cu was prevented by the decrease in the molar ratio, as mentioned before. By melting incineration fly ash with the low molar ratio in a non-oxidative atmosphere, most of the Pb and Zn in the ash were volatilized leaving behind Fe and Cu.     

Thermodynamic and experimental studies on condensation behavior of low-boiling-point elements volatilized in the melting process

To study the volatilization and condensation behaviors of low-boiling-point elements in the waste melting process, experiments were conducted to collect the dust from a coke-type incineration residue melting furnace. Then, a comparison was made between the experimental results and the calculated values obtained from a thermodynamic equilibrium model in terms of the chemical composition of the dust. The composition of the dust collected from a cylindrical filter in the exhaust gas duct was determined by chemical methods, scanning electron microscopy/energy-dispersive X-ray spectroscopy, and X-ray analysis. As a result, the sampled dust was classified into two different types: fine particles mainly containing Na, K, Pb, and Zn collected from the side face of the cylindrical filter, and large particles containing Ca, Si, and Al collected from the bottom face of the cylindrical filter. From X-ray analysis of the sampled dust, NaCl, KCl, PbS, and ZnS were identified in the fine-particle dust, while CaO, SiO₂, Al₂O₃ were detected in the large-particle dust. From the results of the thermodynamic equilibrium calculation in the gas cooling process from 2000 to 600 K, it was found that Na, K, Pb, and Zn volatilized as metals in the melting furnace were condensed as alkali chlorides such as NaCl and KCl and heavy metal sulfides such as PbS and ZnS. These computational results were in good agreement with the X-ray diffraction results of the sampled dust at a gas temperature of 823 K for the formation of NaCl, KCl, PbS, and ZnS.     

Leachability of municipal solid waste ashes in simulated landfill conditions

In Japan the volume of municipal solid waste is reduced by incineration, with fly ash and bottom ash disposed in controlled landfills. The leachability of anions and heavy metal cations, Zn, Cu and Pb, from MSW fly ash and bottom ash at different pHs was examined using batch- and column-leaching tests. The MSW ashes had a high capacity for neutralizing acids. Behaviour during leaching depended on the pH of the solution. For the volumes applied, the leachabilities of MSW fly ash were very similar at pHs from 3 to 6. Due to its amphoteric nature, Pb is leachable at pHs of approximately 10 or more, with leachate concentrations of about 3 and 3-10mg/L for the fly ash and bottom ash, respectively, much higher than for Zn and Cu. Pb concentrations for most leaching solutions were 1 and 3mg/L for the fly ash and bottom ash, respectively. Zn, and Cu leached at low concentrations for solutions of pH 3-6. Na and K ions leached at high concentrations of approximately 5000 mg/L in the first batch leaching test, decreasing to 10mg/L by the fourth leach. Ca and Mg ions leached more gradually than Na and K. Cl(-) and SO(4)(2+) ions were the major anions in the MSW ash. The high pH and cation leaching are expected to have negative impacts on the performance of clay liners.     

Leaching from MSWI bottom ash: evaluation of non-equilibrium in column percolation experiments

Impacts of non-equilibrium on results of percolation experiments on municipal solid waste incineration (MSWI) bottom ash were investigated. Three parallel column experiments were performed: two columns with undisturbed percolation and one column with two sets of 1-month-long flow interruptions applied at liquid-to-solid (L/S) ratios of L/S 2L/kg and 12L/kg, respectively. Concentrations of Na, K, Cl(-), Ca, Si, SO(4)(2-), Al, Cu, Ni, Mo, Ba, Pb, Zn, and dissolved organic carbon (DOC) were monitored throughout the entire leaching period; geochemical modeling was used to identify non-equilibrium-induced changes in the solubility control. Despite both physical and chemical non-equilibrium, the columns were found to provide adequate information for readily soluble compounds (i.e., Na, Cl(-), and K) and solubility-controlled elements (i.e., Ca, SO(4)(2-), Ba, Si, Al, Zn, and Pb). The leaching of Cu and Ni was shown to depend strongly on DOC leaching, which was likely affected by physical non-equilibrium during flow interruptions. Consequently, the leaching of Cu and Ni in the undisturbed columns was shown to be by about one order of magnitude lower compared with the interrupted column. The results indicate that the leaching of DOC-related metals in laboratory column experiments may be considerably underestimated compared with full-scale scenarios in which the impacts from non-equilibrium may be significantly lower. The leaching of Mo (or MoO(4)(2-)) may be controlled solely by its availability in the mobile zone, which in turn appeared to be controlled by diffusion from the stagnant zone; no Mo controlling minerals were predicted by the geochemical modeling.     

Effect of chlorine on volatilization of Na, K, Pb, and Zn compounds from municipal solid waste during gasification and melting in a shaft-type furnace

In the present work, a shaft-type furnace model in which the furnace column is divided into multiple cells was proposed and equilibrium reaction calculation software was used to describe the model. The model was used to study the effects of gasification and melting conditions such as temperature, oxygen partial pressure, and chlorine content on the volatilization behaviors of the low-boiling-point metals Na, K, Pb, and Zn during the gasification and melting process of municipal solid waste in a shaft-type furnace. Consequently, the volatilization ratios of Na, K, Pb, and Zn compounds in the exhaust gas from a pilot plant shaft-type furnace were found to be in good agreement with the calculation results, and the Na, K, Pb, and Zn compounds were volatilized mainly as metal chlorides in the temperature range up to approximately 1173 K. With a further rise in temperature, these low-boiling point metals were volatilized as metallic forms. It was found that almost 100% of Pb and Zn compounds were volatilized regardless of the chlorine content in municipal solid waste; in contrast, the volatilization rates of Na and K increased when the chlorine content increased. Finally, Na, K, Pb, and Zn compounds were converted from reduced metals to metal chlorides such as NaCl, KCl, PbCl₂, and ZnCl₂ with an increase in the ratio of chlorine to each metal.     

Petrographic and spectroscopic characterization of phosphate-stabilized mine tailings from Leadville,Colorado

The use of soluble PO4(3-) and lime as a heavy metal chemical stabilization agent was evaluated for mine tailings from Leadville, Colorado. The tailings are from piles associated with the Wolftone and Maid of Erin mines; ore material that was originally mined around 1900, reprocessed in the 1940s, and now requires stabilization. The dominant minerals in the tailings are galena (PbS), cerrusite (PbCO3), pyromorphite (Pb5(PO4)3Cl), plumbojarosite (Pb0.5Fe3(SO4)2(OH)6), and chalcophanites ((Pb,Fe,Zn,Mn)Mn2O5 x 2H2O). The tailings were treated with soluble PO4(3-) and lime to convert soluble heavy metals (principally Pb, Zn, Cu, Cd) into insoluble metal phosphate precipitates. The treatment process caused bulk mineralogical transformations as well as the formation of a reaction rind around the particles dominated by Ca and P. Within the mineral grains, Fe-Pb phosphosulfates, Fe-Pb sulfates (plumbojarosite), and galena convert to Fe-Ca-Pb hydroxides. The Mn-Pb hydroxides and Mn-(+/-Fe)-Pb hydroxides (chalcophanites) undergo chemical alteration throughout the grains during treatment. Bulk and surface spectroscopies showed that the insoluble reaction products in the rind are tertiary metal phosphate (e.g. (Cu,Ca2)(PO4)2) and apatite (e.g. Pb5(PO4)3Cl) family minerals. pH-dependent leaching (pH 4,6,8) showed that the treatment was able to reduce equilibrium concentrations by factors of 3 to 150 for many metals; particularly Pb2+, Zn2+, Cd2+, and Cu2+. Geochemical thermodynamic equilibrium modeling showed that apatite family and tertiary metal phosphate phases act as controlling solids for the equilibrium concentrations of Ca2+, PO4(3-) Pb2+, Zn2+, Cd2+, and Cu2+ in the leachates during pH-dependent leaching. Both end members and ideal solid solutions were seen to be controlling solids.     

Solidification with water as a treatment method for air pollution control residues

The process of solidification with water was studied on air pollution control (APC) residues from incineration of refuse-derived fuel (RDF) regarding mechanical strength and leaching behaviour of solidified material. Factorial design in two levels was applied to investigate the impact of water addition, time, and temperature to mechanical strength of solidified material. Factors time and temperature, as well as the interaction between the addition of water and time significantly (alpha=0.05) influenced the mechanical strength of solidified material. The diffusion-leaching test NEN 7345 was performed to investigate if the leaching behaviour of elements from solidified material was determined by diffusion. Since it was found that leaching is not diffusion controlled, the long-term leaching behaviour was not assessed. However, the investigation showed that some of the studied components (Al, Hg, Mn, Pb, Si, and Zn) could be considerably demobilised by solidification with water. Concentrations of As, Cd, Co, Cu, Fe, and Ni were either below or not quite above the detection limits to be included in the analysis of leaching behaviour. The elements least demobilised by solidification were Cl, Cr, K, and Na.     

Characterization of trace elements in chicken and duck litter ash

For safe and sustainable management of poultry litter, it is important to evaluate and understand the chemical forms and concentrations of their constituent trace elements during treatment for disposal. This experiment was carried out to compare changes in metal (Cu, Mn, Zn, Pb and Ni) fractions in chicken and duck litter after incineration at temperatures ranging from 200 to 900 degrees C. The metals were stepwise fractionated into exchangeable, adsorbed, organically bound, carbonate precipitated and residual forms by extracting with 0.5M KNO3, de-ionized water, 0.5M NaOH, 0.05M Na2 EDTA and 4M HNO3, respectively. The content of total metal and other elements (i.e., Ca, Mg and K) were was also determined. Results showed an increasing trend in the total concentrations of metals with increasing temperature with higher amounts in chicken litter ash (CLA) than duck litter ash (DLA). Higher temperatures significantly reduced the levels of H2O-soluble Mn, Zn and Ni and enhanced those of Cu and Pb. The metal fractions extracted by EDTA and HNO3 increased directly with increasing temperature while the fraction extracted with KNO3 and NaOH decreased with ashing. For Cu, Mn, Pb and Ni, the amount extracted varied in the order EDTA>HNO3>NaOH>KNO3>H2O, but the absolute amounts differed between CLA and DLA. Peak concentrations of the total metals were achieved at the highest burning temperature. The amount of H2O soluble Ca and Mg decreased and K increased in both CLA and DLA with temperature. Total and exchangeable forms of cations increased with increasing temperature. Total Ca was highest in DLA, whereas total Mg and K were higher in CLA. This study indicated that incinerating poultry litter before soil application may have mixed effects on the vulnerable metal fractions by increasing or decreasing some fractions, depending on poultry type.     

Impact of moisture on volatility of heavy metals in municipal solid waste incinerated in a laboratory scale simulated incinerator

In this work, the impact of moisture on the volatility of heavy metals present in municipal solid wastes (MSW) in a laboratory scale simulated incinerator was studied, using synthetic waste consisting of 5.4 g of wood powder, 2.6 g lava, 1.9 polythene, 0.19 g polyvinyl chloride, and a given quantity of water and heavy metals represented by lead, zinc and copper in forms of metallic, chlorides and oxides. It is found that the presence of high moisture in MSW will greatly reduce the volatilization of heavy metals in MSW in the incineration process. The volatilization behavior of chlorides, oxides and the metallic species with respect to the effect of moistures is quite different. For copper, the presence of moisture in MSW depresses the volatilization of oxides, and increases that of chloride and the metallic species, while in contrast, the volatilization of both lead and zinc is always depressed by the presence of moisture in MSW, regardless of the chemical forms used. The chemical mechanisms, which govern the volatilization behaviors of different chemical forms in the incineration process, are proposed. Hydrolysis, dewatering of hydrolyzed species, sublimation, chemical transformation of less volatiles to more volatiles or reverse, may participate in and affect the volatilization of heavy metals in MSW.     

Leaching from solid waste incineration ashes used in cement-treated base layers for pavements

Waste incineration bottom ash and treated flue gas cleaning products mixed with 2.5% of cement (50 kg/m3) were tested in the laboratory in terms of compressive strength and tank leaching tests over a 64-day period. Although the material displayed lower mechanical strength than a reference concrete, the strength still was sufficient for use as a base layer for roads. The metal content in the incineration-residue-based specimens was up to 100 times higher than in the reference concrete, suggesting that the mixed waste incineration residue should be used only for dedicated purposes. The leaching of Cl and Na was increased by a factor of 20-100 from the incineration-residue-based specimens as compared to the reference, while the leaching of K, Ca and SO4 was increased by a factor of 2-10. The leaching of heavy metals was also higher from the incineration-residue-based specimens than from the reference with respect to Cu (50 times), Cd, Pb and Zn (5 times), but not with respect to Cr and Ni. The leaching curves did only allow for a closer evaluation of the leaching process in a few cases. The physical retention of the constituents seemed to be the same in the reference as in the incineration-residue-based specimens. Heavy metal leaching was limited by enhanced chemical retention in the incineration-residue-specimens as compared to the reference. Since no quality criteria in terms of leaching from a monolithic material are currently available, the leaching issue must be evaluated case by case.     

Aqueous leaching of cattle manure incineration ash to produce a phosphate enriched fertilizer

Ash produced from the combustion of livestock manure contains large amounts of phosphorus (P), which is an important resource as a fertilizer. Some studies have extracted and recovered P from incinerated biomass ash using inorganic acid or alkaline agents, which produce wastewater that requires treatment and is expensive due to the cost of chemicals. Livestock manure ash contains not only P, but also water soluble salts, which could be a negative influence on plant growth and shall be preferably removed from the recovered fertilizer. In this study, we removed salinity from cattle manure incineration ash by simple aqueous leaching, while retaining the P content. The optimal condition was a 20 min leaching time at a liquid/solid (L/S) ratio of 10 mL g-ash^?1. Under this condition, over 90 % of Cl and 20 % of Na in the original ash was removed, while over 99 % of the P was retained in the leached residue. The leached residue met the fertilizer standard in Japan in terms of citrate soluble fertilizer components and contained few heavy metals. X-ray analyses of the ash indicated that Cl was mainly present as KCl in the original ash, while P was mainly present as Ca compounds in the ash.     

Leaching of heavy metals by citric acid from fly ash generated in municipal waste incineration plants

The leaching behavior of heavy metals from municipal waste incineration (MWI) fly ash was investigated in this study. The leaching process includes two steps, i.e., fly ash was firstly washed with water, and then subjected to citric acid leaching. The main parameters of the washing process such as liquid/solid ratio, washing time, and number of washing were tested. The optimum conditions for water washing were found as follows: washing time 5–10 min, liquid/solid ratio 10:1 (ml:g), and number of washing was twice; under these conditions, 86% Na, 70% K, 12% Ca, 1.2% Al, and 0.5% Pb were removed from the fly ash in the prewashing. From the results of screening tests of leaching lixiviants, citric acid was found to be the most effective leaching agent, taking account of its environmentally benign characteristics. Optimum metal extraction can be achieved with citric acid under the following conditions: pH 3.0, liquid/solid ratio 40 (ml:g), citric acid concentration 0.10 mol/dm³, contact time 20 min at room temperature.     

Treatment-oriented characterization of dry scrubber residue from municipal solid waste incineration

 Dry scrubber residue from municipal solid waste incineration (MSWI) was characterized to identify critical inorganic pollutants and to suggest a conceptual treatment method. The key methods used were thermal analysis, including thermogravimetry (TG) and differential thermal analysis (DTA), pH_stat titration, qualitative X-ray diffraction (XRD), scanning electron microscopy (SEM), chemical equilibrium calculations, and statistics such as error propagation, principal component analysis (PCA), and empirical modeling based on factorial designs. Based on EU directives, the major inorganic pollutants Cd, Cr, Pb, and Zn were found. In addition, the pH was too high. With dry scrubber residue stabilization in mind, the impact of carbonation and hydration was assessed and judged to be encouraging. In particular, chemical equilibrium calculations showed that carbonation has considerable potential to lower the pH and the availability of Pb, Zn, and Cr. The impact of carbonation on the mobility of Cd was found to be small. During carbonation, a metal-trapping calcium aluminosilicate hydrate (C–A–S–H) phase is also formed. Both processes together have the potential to lead to a robust, reliable, and reasonable stabilization method for dry scrubber residue. However, to control these processes, the decisive factors need to be identified and their effects need to be quantified. Ca, Cl, Na, and K might be abundant components which would be mobile even after stabilization. Received: September 11, 2001 / Accepted: December 6, 2001     

Metal distribution in incineration residues of municipal solid waste (MSW) in Japan

This study aimed to identify distribution of metals and the influential factors on metal concentrations in incineration residues. Bottom ash and fly ash were sampled from 19 stoker and seven fluidized bed incinerators, which were selected to have a variety of furnace capacity, furnace temperature, and input waste. In the results, shredded bulky waste in input waste increased the concentration of some metals, such as Cd and Pb, and the effect was confirmed by analysis of shredded bulky waste. During MSW incineration, lithophilic metals such as Fe, Cu, Cr, and Al remained mainly in the bottom ash while Cd volatilized from the furnace and condensed to the fly ash. About two thirds of Pb and Zn was found in the bottom ash despite their high volatility. Finally, based on the results obtained in this study, the amount of metal in incineration residues of MSW was calculated and the loss of metal was estimated in terms of mass and money. A considerable amount of metal was found to be lost as waste material by landfilling of incineration residues.     

Influence of calcium chloride on the thermal behavior of heavy and alkali metals in sewage sludge incineration

In order to separate and reuse heavy and alkali metals from flue gas during sewage sludge incineration, experiments were carried out in a pilot incinerator. The experimental results show that most of the heavy and alkali metals form condensed phase at temperature above 600 degrees C. With the addition of 5% calcium chloride into sewage sludge, the gas/solid transformation temperature of part of the metals (As, Cu, Mg and Na) is evidently decreased due to the formation of chloride, while calcium chloride seems to have no significant influence on Zn and P. Moreover, the mass fractions of some heavy and alkali metals in the collected fly ash are relatively high. For example, the mass fractions for Pb and Cu in the fly ash collected by the filter are 1.19% and 19.7%, respectively, which are well above those in lead and copper ores. In the case of adding 5% calcium chloride, the heavy and alkali metals can be divided into three groups based on their conversion temperature: Group A that includes Na, Zn, K, Mg and P, which are converted into condensed phase above 600 degrees C; Group B that includes Pb and Cu which solidify when the temperature is above 400 degrees C; and Group C that includes As, whose condensation temperature is as low as 300 degrees C.     

Leaching characteristics of rare metal elements and chlorine in fly ash from ash melting plants for metal recovery

In terms of resource recovery and environmental impact, melting furnace fly ash (MFA) is attracting much attention in Japan due to its high metal content. The study aims to obtain fundamental information on using a water extraction method not only to concentrate valuable rare metals but also to remove undesirable substances such as chlorine for their recovery from MFA. The composition and leaching characteristics of MFA was investigated. The results revealed that the metal content in MFA is nearly equal to raw ore quality. The content of Ag, In, Pd, Pb, and Zn is, in fact, higher than the content of raw ore. As for leaching behavior, Ag, Bi, In, Ga, Ge, Sb, Sn, and Te showed the lowest release at a neutral pH range. Pd was leached constantly regardless of pH, but its concentration was quite low. On the other hand, most of the Tl was easily leached, revealing that water extraction is not appropriate for Tl recovery from MFA. Major elements Cl, Ca, Na, and K, occupying about 70% of MFA, were mostly leached regardless of pH. Base metal elements Cu, Pb, and Zn showed minimum solubility at a neutral pH. The leaching ratio of target rare metal elements and base metal elements suggests that the optimal pH for water extraction is 8-10, at which the leaching concentration is minimized. The water extraction process removed most of the Cl, Ca, Na, and K, and the concentration of rare metals and base metals increased by four or five times.     

Fixation and partitioning of heavy metals in slag after incineration of sewage sludge

Fixation of heavy metals in the slag produced during incineration of sewage sludge will reduce emission of the metals to the atmosphere and make the incineration process more environmentally friendly. The effects of incineration conditions (incineration temperature 500-1100°C, furnace residence time 0-60min, mass fraction of water in the sludge 0-75%) on the fixation rates and species partitioning of Cd, Pb, Cr, Cu, Zn, Mn and Ni in slag were investigated. When the incineration temperature was increased from 500 to 1100°C, the fixation rate of Cd decreased from 87% to 49%, while the fixation rates of Cu and Mn were stable. The maximum fixation rates for Pb and Zn and for Ni and Cr were reached at 900 and 1100°C, respectively. The fixation rates of Cu, Ni, Cd, Cr and Zn decreased as the residence time increased. With a 20min residence time, the fixation rates of Pb and Mn were low. The maximum fixation rates of Ni, Mn, Zn, Cu and Cr were achieved when the mass fraction of water in the sludge was 55%. The fixation rate of Cd decreased as the water mass fraction increased, while the fixation rate of Pb increased. Partitioning analysis of the metals contained in the slag showed that increasing the incineration temperature and residence time promoted complete oxidation of the metals. This reduced the non-residual fractions of the metals, which would lower the bioavailability of the metals. The mass fraction of water in the sludge had little effect on the partitioning of the metals. Correlation analysis indicated that the fixation rates of heavy metals in the sludge and the forms of heavy metals in the incinerator slag could be controlled by optimization of the incineration conditions. These results show how the bioavailability of the metals can be reduced for environmentally friendly disposal of the incinerator slag.     

Chemical properties of heavy metals in typical hospital waste incinerator ashes in China

Incineration has become the main mechanism for hospital waste (HW) disposal in China after the outbreak of Severe Acute Respiratory Syndrome (SARS) in 2003. However, little information is available on the chemical properties of the resulting ashes. In the present study, 22HW ash samples, including 14 samples of bottom ash and eight samples of fly ash, were collected from four typical HW incineration plants located across China. Chemical analysis indicated that the HW ashes contained large amounts of metal salts of Al, Ca, Fe, K, Mg, Na with a concentration range of 1.8-315gkg(-1). Furthermore, the ashes contained high concentrations of heavy metals such as Ag, As, Ba, Bi, Cd, Cr, Cu, Mn, Ni, Pb, Ti, Sb, Sn, Sr, Zn with a vast range of 1.1-121,411mgkg(-1), with higher concentrations found in the fly ash samples. Sequential extraction results showed that Ba, Cr, Ni and Sn are present in the residual fraction, while Cd existed in the exchangeable and carbonate fractions. As, Mn, Zn existed in the Fe-Mn oxide fraction, Pb was present in the Fe-Mn oxide and residual fractions, and Cu was present in the organic matter fraction. Furthermore, toxicity characteristic leaching procedure (TCLP) results indicated that leached amounts of Cd, Cu and Pb from almost all fly ash samples exceeded the USEPA regulated levels. A comparison between the HW ashes and municipal solid waste (MSW) ash showed that both HW bottom ash and fly ash contained higher concentrations of Ag, As, Bi, Cd, Cr, Cu, Pb, Ti, and Zn. This research provides critical information for appropriate HW incineration ash management plans.     

Percolation and batch leaching tests to assess release of inorganic pollutants from municipal solid waste incinerator residues

In this study, percolation and batch leaching tests were considered in order to characterize the behaviour of air pollution control (APC) residues produced in a municipal solid waste incinerator (MSWI) as a function of the liquid to solid ratio (L/S). This waste is hazardous, and taking into account their physical and chemical properties, leaching of contaminants into the environment is the main concern. In our work the leaching behaviour of toxic heavy metals (Pb, Zn, Cr, Ni and Cu) and inorganics associated with soluble salts (Na, K, Ca and Cl) was addressed. Although pH of the leaching solution is the most important variable, L/S may also play an important role in leaching processes. In our work, results from column and batch tests were compared in terms of concentration (mg/L) and releasing (mg/kg). The APC residues revealed to be hazardous according to both tests, and both Pb and Cl⁻ far exceeded the regulatory thresholds. The material exhibits high solubility, and when the liquid to solid ratio was high, more than 50% can be solubilised. The patterns of release may be in some cases availability or solubility controlled, and the former was easier to identify. When the results from column and batch experiments were compared by representing the cumulative released amounts (in mg/kg) as a function of L/S, both curves match for Zn, Ni, Cu, K, Na, Cl and Ca, but for Cr and Pb a significant difference was observed. In fact, the column experiments revealed that under percolation conditions it should be expected slow releasing of Pb along time. From this study, it can be concluded that the released amounts obtained in batch experiments for a certain L/S should be considered as the worst case for medium term. Some simple models proposed on the literature and based on local equilibrium assumption showed good fitting to experimental data for soluble species (non-reactive solutes).     

Trace element partitioning in ashes from boilers firing pure wood or mixtures of solid waste with respect to fuel composition,chlorine content and temperature

Trace element partitioning in solid waste (household waste, industrial waste, waste wood chips and waste mixtures) incineration residues was investigated. Samples of fly ash and bottom ash were collected from six incineration facilities across Sweden including two grate fired and four fluidized bed incinerators, to have a variation in the input fuel composition (from pure biofuel to mixture of waste) and different temperature boiler conditions. As trace element concentrations in the input waste at the same facilities have already been analyzed, the present study focuses on the concentration of trace elements in the waste fuel, their distribution in the incineration residues with respect to chlorine content of waste and combustion temperature.Results indicate that Zn, Cu and Pb are dominating trace elements in the waste fuel. Highly volatile elements mercury and cadmium are mainly found in fly ash in all cases; 2/3 of lead also end up in fly ash while Zn, As and Sb show a large variation in distribution with most of them residing in the fly ash. Lithophilic elements such as copper and chromium are mainly found in bottom ash from grate fired facilities while partition mostly into fly ash from fluidized bed incinerators, especially for plants fuelled by waste wood or ordinary wood chips. There is no specific correlation between input concentration of an element in the waste fuel and fraction partitioned to fly ash. Temperature and chlorine content have significant effects on partitioning characteristics by increasing the formation and vaporization of highly volatile metal chlorides. Zinc and cadmium concentrations in fly ash increase with the incineration temperature.