The hydration characteristics and utilization of slag obtained by the vitrification of MSWI fly ash

This study investigated the effects of slag composition on the hydration characteristics of slag blended cement (SBC) pastes. Synthetic slag samples were prepared by melting CaO-modified and Al(2)O(3)-modified municipal solid waste incinerator (MSWI) fly ash. MSWI fly ash was mixed with 5% CaO and 5% Al(2)O(3) (by weight), respectively, resulting in two fly ash mixtures. These mixtures were then melted at 1400 degrees C for 30 min to produce two types of slag with different contents, designated at C-slag and A-slag. Both the C-slag and A-slag samples exhibited a pozzolanic activity index higher than the unmodified slag sample. The results show that the synthetic slags all met the Taiwan EPA's current regulatory thresholds. These synthetic slags were then blended with ordinary Portland cement (OPC) at various weight ratios ranging from 10 to 40%. The 28-day strength of the C1 paste was higher than that developed by the OPC paste, suggesting that the C-slag contributed to the earlier strength of the SBC pastes. At curing times beyond 28 days, the strength of the A1 paste samples approached that of the OPC paste samples. It can be seen from this that increasing the amount of calcium and aluminum oxide increases the early strength of SBC. The C-slag blended cement paste samples showed an increase in the number of fine pores with the curing time, showing that the C-slag enhanced the pozzolanic reactions, filling the pores. Also, the incorporation of a 10% addition of C-slag also tended to enhance the degree of hydration of the SBC pastes during the early ages (3-28 days). However, at later ages, no significant difference in degree of hydration between the OPC pastes and the SBC pastes was observed with the 10% C-slag addition. However, the incorporation of A-slag did decreased the degree of hydration. A slag blend ratio of 40% significantly decreased the hydration degree.     

Enhancement of Sedimentation Velocity of Heavy Metals Loaded Hydroxyapatite Using Chitosan Extracted from Shrimp Waste

In this study, synthesize hydroxyapatite (HA) suspensions sedimentation was used after usual terms as support for adsorption of heavy metals ions. Thus, the effectiveness of chitosan, produced from shrimp waste, in the flocculation of turbid suspensions resulting from the treatment of water contaminated with heavy metals was studied by adsorption on HA. Different particles sizes of HA were mainly controlled in this work (an average of granule size ranging from 1.6 to 63 μm). The results of Cu²⁺ and Zn²⁺ adsorption on HA showed relatively fast kinetics, with removal extent of 88–95 % by varying the initial total metal concentration. High removal rates were obtained for Cu²⁺. Chitosan was found to be able to eliminate by flocculation more than 98 % of turbid suspensions generated by metals adsorption on HA after only 30 min of sedimentation. Effects of pH and dose of chitosan on the coagulation–flocculation process were also studied. The optimal dose of chitosan was found between 0.2 and 2 mg/L which corresponds to an optimal pH ranging from 6 to 7.     

Hydration and leaching characteristics of cement pastes made from electroplating sludge

The purpose of this study was to investigate the hydration and leaching characteristics of the pastes of belite-rich cements made from electroplating sludge. The compressive strength of the pastes cured for 1, 3, 7, 28, and 90 days was determined, and the condensation of silicate anions in hydrates was examined with the ²⁹Si nuclear magnetic resonance (NMR) technology. The leachabilities of the electroplating sludge and the hardened pastes were studied with the multiple toxicity characteristic leaching procedure (MTCLP) and the tank leaching test (NEN 7345), respectively. The results showed that the electroplating sludge continued to leach heavy metals, including nickel, copper, and zinc, and posed a serious threat to the environment. The belite-rich cement made from the electroplating sludge was abundant in hydraulic β-dicalcium silicate, and it performed well with regard to compressive-strength development when properly blended with ordinary Portland cements. The blended cement containing up to 40% the belite-rich cement can still satisfy the compressive-strength requirements of ASTM standards, and the pastes cured for 90 days had comparable compressive strength to an ordinary Portland cement paste. It was also found that the later hydration reaction of the blended cements was relatively more active, and high fractions of belite-rich cement increased the chain length of silicate hydrates. In addition, by converting the sludge into belite-rich cements, the heavy metals became stable in the hardened cement pastes. This study thus indicates a viable alternative approach to dealing with heavy metal bearing wastes, and the resulting products show good compressive strength and heavy-metal stability.     

Adsorption characteristics of Cu2+ and Zn2+ from aqueous solution using carbonized food waste

The aim of the present study was to analytically provide adsorption characteristics of Cu²⁺ and Zn²⁺ using carbonized food waste (CFW); more specifically, batch tests were conducted using various concentrations of metal ions, contact times, and initial pH levels in an attempt to understand the adsorption removal of heavy metal ions in aqueous solution at concentrations ranging between 50 and 800 mg/l. The results confirmed that the adsorption equilibrium was established within a maximum of 80 min, and the maximum concentrations for adsorption of Cu²⁺ and Zn²⁺ were 28.3 and 23.5 mg/g, respectively. These adsorption levels indicate that CFW has better performance than many other adsorbents. In experiments using different pH conditions, the applicability to acid wastewater was found to be high, and an excellent adsorption removal ratio of 75%–90% was observed under acid conditions at pH 2–4. Furthermore, as the adsorption time increased, the calcium component in the CFW began to leach into the aqueous solution and raise the pH, accordingly causing the removal of heavy metal ions partially as a result of precipitation. When our results were analyzed using the Langmuir model and the Freundlich model for isothermal adsorptivity, the activity of CFW in this study was shown to be more consistent with the former; the adsorption speed of Cu²⁺ and Zn²⁺ according to a pseudosecond-order reaction model was found to be very fast for an initial concentration of not more than 100 mg/l. In a test in which an attempt was made to compare adsorption capacity values obtained from the experiments in this study with the aforementioned three models, the pseudosecond-order reaction model was found to provide results closest to the actual values.     

Investigative studies for inert transformation of toxic chrysotile tailing

In an attempt to find ways to reduce consumption of natural raw material and recycle chrysotile tailing waste (CTW), cordierite ceramics were produced using CTW, kaolin tailing waste (KTW) and waste alumina. Before synthesizing the cordierite ceramics, the inert transformation of CTW was investigated via a thermal treatment. Experimental results indicated that CTW was converted into nonhazardous forsterite and enstatite at temperatures above 1000 °C. The characterizations of the synthesized cordierite ceramics were examined using thermal analyses, X-ray diffraction (XRD), morphological structure analyses, compressive strength measurement, coefficient of thermal expansion (CTE) and toxicity characteristic leaching procedure (TCLP). Thermal analyses indicated that significant weight loss below 900 °C was the release of structural water and gases. XRD indicated that the cordierite became the main crystalline phase at 1350 °C. Compressive strength test indicated that compressive strength of the cordierite ceramics was 260 MPa, and CTE of cordierite ceramics was 2.4 × 10^?6 °C^?1. This technology for the of utilization of CTW and KTW could be used to produce industrial cordierite ceramics, in accordance with the concepts of sustainable development.     

Poultry litter-based activated carbon for removing heavy metal ions in water

Utilization of poultry litter as a precursor material to manufacture activated carbon for treating heavy metal-contaminated water is a value-added strategy for recycling the organic waste. Batch adsorption experiments were conducted to investigate kinetics, isotherms, and capacity of poultry litter-based activated carbon for removing heavy metal ions in water. It was revealed that poultry litter-based activated carbon possessed significantly higher adsorption affinity and capacity for heavy metals than commercial activated carbons derived from bituminous coal and coconut shell. Adsorption of metal ions onto poultry litter-based carbon was rapid and followed Sigmoidal Chapman patterns as a function of contact time. Adsorption isotherms could be described by different models such as Langmuir and Freundlich equations, depending on the metal species and the coexistence of other metal ions. Potentially 404 mmol of Cu²⁺, 945 mmol of Pb²⁺, 236 mmol of Zn²⁺, and 250–300 mmol of Cd²⁺ would be adsorbed per kg of poultry litter-derived activated carbon. Releases of nutrients and metal ions from litter-derived carbon did not pose secondary water contamination risks. The study suggests that poultry litter can be utilized as a precursor material for economically manufacturing granular activated carbon that is to be used in wastewater treatment for removing heavy metals.     

Cement-clay pastes for stabilization/solidification of 2-chloroaniline

Immobilization of a model liquid organic pollutant, i.e. the 2-chloroaniline (2-CA), into a cement matrix using organoclays as pre-sorbent agents was investigated. Five cement-clay pastes were prepared with different nominal water-to-cement ratios (w/c=0.40, 0.25 and 0.15 wt/wt) and various amounts of waste (waste-to-cement o/c=0.20, 0.60 and 1.00 wt/wt); for comparison, a neat cement paste was also prepared. Dynamic leach tests were performed on solidified monoliths in order to assess the successful immobilization of the 2-CA. In monoliths at constant w/c ratio (0.40) the total amount of pollutant released increases with its initial content, and ranges from 15 to 35% with respect to it. By lowering w/c from 0.40 to 0.15 at constant o/c, the performances improved (<25% released). The microstructure of the hardened cement-clay pastes was characterized by quantitative X-ray diffraction (QXRD) and electronic microscopy (SEM-EDS) techniques; hydration degree was estimated by means of thermogravimetric analysis (TGA) in addition to QXRD. No evidence of any chemical reaction between 2-CA and cement phases was found. Moreover, it was shown that the most important factors affecting the cement hydration process were the total water content, i.e. the one taking also into account the water contained in the wet polluted clay, and the amount of 2-CA not firmly sorbed by the organoclay, and then freely dispersed in the paste.     

Stabilization/solidification of MSW incineration residues from facilities with different air pollution control systems. Durability of matrices versus carbonation

This paper discusses the stabilisation/solidification process with Portland cement applied to municipal solid waste incineration residues. Two types of residues were considered: fly ash (FA) produced in an electrostatic precipitator, and air pollution control (APC) residues from a semi-dry scrubber process. Cement pastes with different percentages of FA and APC residues were characterised according to their physical properties, the effect of the hydration products and their leaching behaviour. Portland pastes prepared with APC residues showed a rapid setting velocity in comparison with setting time for those pastes substituted with FA residues. Portland cement hydration was retarded in FA pastes. Leaching test results showed that heavy metals (such as Zn, Pb and Cd) and sulphates are immobilised within the paste, whereas chlorides are only partially retained. The carbonation process increases the leachability of S04(2-) and heavy metals such as Zn and Cr.     

Preparation,Characterization, and Rapid Adsorption of Hg<Superscript>2+</Superscript> on Nanoscale Aramid-based Adsorbent

A series of nanaoscale aramid-based adsorbents were prepared by the functionalization of poly (p-phenylene terephthalamide) (PPTA) with different content of ethylenediamine (EDA). Their structures were characterized by field emission scanning electron microscopy, transmission electron microscopy, Fourier transform infrared spectroscopy, thermogravimetric analysis, and elemental analysis. Metal ions, including Hg²⁺, Pb²⁺, Ag⁺, Cu²⁺, Cd²⁺, and Ni²⁺ were chosen as the models to explore the binding behaviors of PPTA–ECH–EDA in aqueous medium. Results showed that PPTA–ECH–EDA exhibited higher adsorption capacity for Hg²⁺ due to their nanoscale structures. In particular, the adsorption rate was so high that equilibrium was achieved within 15 min for Hg²⁺. The adsorption of Hg²⁺ on PPTA–ECH–EDA followed the pseudo second-order model well. Langmuir and Freundlich models were employed to fit the isothermal adsorption, and the results revealed that Freundlich isotherm was a better model to predict the experimental data. The adsorption mechanism was revealed by X-ray photoelectron spectroscopy. It is preconceived that PPTA–ECH–EDA could be used as an effective adsorbent for fast removal of heavy ions from wastewater.     

Enhanced bioleaching efficiency of copper from waste printed circuit boards (PCBs) by dissolved oxygen-shifted strategy in <Emphasis Type="Italic">Acidithiobacillus ferrooxidans</Emphasis>

Acidithiobacillus ferrooxidans, as chemolithotrophic aerobic bacterium, can obtain energy by oxidation of ferrous ions (Fe²⁺) to ferric ions (Fe³⁺) and use molecular oxygen (O₂) as terminal electron acceptor. In this study, the effects of dissolved oxygen (DO) levels in culture medium on cell growth and copper extraction from waste printed circuit boards (PCBs) were investigated in A. ferrooxidans. The whole culture period was divided into two stages of cell growth and copper extraction. At the former stage, relatively lower DO level was adopted to satisfy bacterial growth while avoiding excessive Fe²⁺ oxidation. At the later stage, higher DO was used to promote copper extraction. Moreover, shift time of DO from lower to higher level was determined via simulating Gauss function. By controlling DO at 10 % for initial 64 h and switching to 20 % afterwards and with 18 g/l PCBs addition at 64 h, final copper recovery reached 94.1 %, increased by 37.6 and 48.3 % compared to constant DO of 10 and 20 % operations. More importantly, copper leaching periods were shortened from 108 to 60 h. It was suggested that application of DO-shifted strategy to enhancing copper extraction from PCBs with reduced leaching periods is being feasible.     

Selection of adsorbents for treatment of leachate: batch studies of simultaneous adsorption of heavy metals

The simultaneous adsorption of copper (Cu), cadmium (Cd), nickel (Ni), and lead (Pb) ions from spiked deionized water and spiked leachate onto natural materials (peat A and B), by-product or waste materials (carbon-containing ash, paper pellets, pine bark, and semi-coke), and synthetic materials (based on urea-formaldehyde resins, called blue and red adsorbents) or mixtures thereof was investigated. The adsorbents that gave the highest metal removal efficiencies were peat A, a mixture of peat B and carbon-containing ash, and a mixture of peat A and blue. At an initial concentration of 5 mg/l for each metal, the removal of each species of metal ion from spiked water and spiked leachate solutions was very good (>90%) and good (>75%), respectively. When the initial concentration of each metal in the solutions was twenty times higher (100 mg/l), there was a noticeable decrease in the removal efficiency of Cu²⁺, Cd²⁺, and Ni²⁺, but not of Pb²⁺. Langmuir monolayer adsorption capacities, q_m, on peat A were found to be 0.57, 0.37, and 0.36 mmol/g for Pb²⁺, Cd²⁺, and Ni²⁺, respectively. The order of metal adsorption capacity on peat A was the same in the case of competitive multimetal adsorption conditions as it was for single-element adsorption, namely Pb²⁺ > Cd²⁺ ≥ Ni²⁺. The results show that peat alone (an inexpensive adsorbent) is a good adsorbent for heavy metal ions.     

Sunflower stalk, an agricultural waste, as an adsorbent for the removal of lead and cadmium from aqueous solutions

Sunflower residue, an agricultural waste material for the removal of lead (Pb) and cadmium (Cd) from aqueous solutions were investigated using a batch method. Adsorbent was prepared by washing sunflower residue with deionized water until the effluent was colorless. Batch mode experiments were carried out as a function of solution pH, adsorbent dosage, initial concentration and contact time. The results indicated that the adsorbent showed good sorption potential and maximum metal removal was observed at pH 5. Within 150 min of operation about 97 and 87 % of Pb and Cd ions were removed from the solutions, respectively. Lead and Cd sorption curves were well fitted to the modified two-site Langmuir model. The adsorption capacities for Pb and Cd at optimum conditions were 182 and 70 mg g^?1, respectively. The kinetics of Pb and Cd adsorption from aqueous solutions were analyzed by fitting the experimental data to a pseudo-second-order kinetic model and the rate constant was found to be 8.42 × 10^?2 and 8.95 × 10^?2 g mg^?1 min^?1 for Cd and Pb, respectively. The results revealed that sunflower can adsorb considerable amount of Pb and Cd ions and thus could be an economical method for the removal of Pb and Cd from aqueous systems.     

Synthesis,Characterization and Environmental Applications of a New Bio-Composite Gelatin-Zr(IV) Phosphate

Gelatin-Zr(IV) phosphate composite (GT/ZPC) was synthesized by sol–gel method. Different techniques viz. Fourier transform infrared spectroscopy (FTIR), thermogravimetric analysis (TGA), X-ray powdered diffraction (XRD), scanning electron microscopy (SEM) and transmission electron microscopy (TEM) were used for the characterisation of GT/ZPC composite ion exchanger. The ion exchange capacity (IEC) of GT/ZPC was observed to be better (1.04 meq g^?1) than its inorganic counterpart (0.64 meq g^?1). The pH studies revealed the monofunctional nature of GT/ZPC with one inflection point. The distribution studies showed that the GT/ZPC was highly selective for Cd²⁺ as compare to other metal ions. The environmental applicability of ion exchanger has been analysed for binary separations of metal ions using column method. Cd²⁺ was effectively removed from synthetic mixture of metal ions (Zn²⁺, Pb²⁺, Ni²⁺, Co²⁺ and Cu²⁺).     

Itaconic Acid Grafted Starch Hydrogels as Metal Remover: Capacity,Selectivity and Adsorption Kinetics

Hydrogels were synthesized by free radical graft copolymerization of itaconic acid (IA) onto corn starch (S-g-IA). For this purpose, potassium permanganate (KMnO₄)-sodium bisulfite (NaHSO₃) was used as redox initiation system. The formation of grafted starches was confirmed by Fourier transform infrared spectroscopy, wide angle X-ray scattering, thermogravimetric analysis and scanning electron microscopy. The effect of monomer concentration, neutralization, addition of crosslinking agent, N,N-bismetilenacrilamide (MBAm), and initiator concentration on grafting efficiency and adsorption capacity of the starch hydrogels was investigated. It was demonstrated that the introduction of carboxyl and carbonyl groups promoted starch hydration and swelling. Grafting degree increased with the decrease of monomer concentration, increase of initiator concentration, grade of neutralization and the addition of MBAm without neutralization. Remarkably the resulting materials exhibited water absorption capacities between 258 and 1878% and the ability to adsorb metal ions. It was experimentally confirmed the metal uptake, obtaining the higher adsorption capacity (q _e  = 35 mg/g) for the product prepared with the pre-oxidation and lower initiator concentration. The removal capacity order was Pb²⁺>Ni²⁺>Zn²⁺>Cd²⁺. Moreover, the experimental kinetic and the equilibrium adsorption data for Ni²⁺ and Pb²⁺ were best fitted to the pseudo-second order and Freundlich isotherm models, respectively. This work describes for the first time the preparation of metal removal hydrogels based on starch and itaconic acid using the pair redox system KMnO₄/NaHSO₃, which avoids the starch hydrolysis and allows itaconic acid grafting incorporation without the requirement of more reactive comonomers.     

Design parameters for fixed bed reactors of activated carbon developed from fertilizer waste for the removal of some heavy metal ions

Activated carbon, developed from fertilizer waste, has been used for the removal of Hg²⁺, Cr⁶⁺, Pb²⁺, and Cu²⁺. Mass transfer kinetic approach has been successfully applied for the determination of various parameters necessary for designing a fixed-bed absorber. Parameters selected are the length of the (PAZ) primary adsorption zone (δ), total time involved for the establishment of primary adsorption zone (t_x), mass rate of flow to the absorber (F_m), time for primary adsorption zone to move down its length (t_δ), amount of adsorbate adsorbed in PAZ from breakpoint to exhaustion (M_s), fractional capacity (f), time of initial formation of PAZ (t_f) and per cent saturation of column at break point. Chemical regeneration has been achieved with 1 M HNO₃.     

Quality improvement of recycled fine aggregate using steel ball with the help of acid treatment

There is a need to promote high-value added utilization of recycled aggregates, considering the aspect of effective use. It should be noted, however, that recycled fine aggregates are generally low in quality due to the presence of cement paste attached to the aggregate surface. Based on this, there have been studies, which aimed to improve the quality of recycled aggregates using mechanical abrasion methods of removing the cement paste based on the principles of crushing, grinding and abrasion and beneficiation method using heat or acid. Accordingly, this study was performed as part of the research to improve the quality of recycled fine aggregates with the aim to effectively remove cement paste using steel ball as mechanical method and acid as chemical method. The results of the experiment showed that the oven-dry density and absorption ratio obtained after the abrasion process using sulfuric acid solution were 2.51 g/cm³ and 2.3%, respectively. This evidenced the quality improvement of the recycled aggregates as they satisfied the quality criteria of over 2.2 g/cm³ and under 5%, respectively, for Class I concrete proposed in the quality standards for recycled aggregates as well as natural sand proposed in Korea Standard criteria of over 2.5 g/cm³ and under 3%.     

Enzyme-Assisted Extraction and Pb<Superscript>2+</Superscript> Biosorption of Polysaccharide from <Emphasis Type="Italic">Cordyceps militaris</Emphasis>

The enzyme assisted extraction conditions of polysaccharide from Cordyceps militaris mycelia were firstly investigated by kinetics analysis and the optimal operating was found to be: extraction temperature 40 °C; solid-solvent ratio 1:20; extraction pH 4.0; cellulase concentration 2.0%. The polysaccharide extraction yield was 5.99% under these optimized conditions. Furthermore, a fundamental investigation of the biosorption of Pb²⁺ from aqueous solution by the C. militaris polysaccharide was performed under batch conditions. The suitable pH (5.0), polysaccharide concentration (0.20 g L^?1), initial Pb²⁺ concentration (300 mg L^?1) and contact time (40 min) were outlined to enhance Pb²⁺ biosorption from aqueous medium. The Langmuir isotherm model and pseudo first order kinetic model fitted well to the data of Pb²⁺ biosorption, suggesting the biosorption of Pb²⁺ onto C. militaris polysaccharide was monolayer biosorption and physical adsorption might be the rate-limiting step that controlled the adsorption process. FTIR analysis showed that the main functional groups of C. militaris polysaccharide involved in adsorption process were carbonyl, carboxyl, and hydroxyl groups.     

Magnetic Cr(VI) Ion Imprinted Polymer for the Fast Selective Adsorption of Cr(VI) from Aqueous Solution

In this study, a novel magnetic Cr(VI) ion imprinted polymer (Cr(VI)-MIIP) was successfully synthesized and used as a selective sorbent for the adsorption of Cr(VI) ions from aqueous solution. It can be synthesized through the combination of an imprinting polymer and magnetic nanoparticles. The high selectivity achieved using MIIP is due to the specific recognition cavities for Cr(VI) ions created in Cr(VI)-MIIP. Also, the magnetic properties that could be obtained using magnetic nanoparticles, helps to separate adsorbent with an external magnetic field without either additional centrifugation or filtration procedures. The magnetic Fe₃O₄ nanoparticles (MNPs) were synthesized using an improved co-precipitation method and modified with tetraethylorthosilicate (TEOS) before imprinting. The magnetic Cr(VI) ion imprinted polymer was prepared through precipitation copolymerization of 4-vinylpyridine as the complexing monomer, 2-hydroxyethyl methacrylate as a co-monomer, the Cr⁶⁺ anion as a template, and ethylene glycol dimethacrylate (EGDMA) as a cross-linker in the presence of modified magnetite nanoparticles. This novel synthesized sorbent was characterized using different techniques. Batch adsorption experiments were performed to evaluate the adsorption conditions, selectivity, and reusability. The results showed that the maximum adsorption capacity was 39.3 mg g^?1, which was observed at pH 3 and at 25?°C. The equilibrium time was 20 min, and the amount of adsorbent which gave the maximum adsorption capacity was 1.7 g L^?1. Isotherm studies showed that the adsorption equilibrium data were fitted well with the Langmuir adsorption isotherm model and the theoretical maximum adsorption capacity was 44.86 mg g^?1. The selectivity studies indicated that the synthesized sorbent had a high single selectivity sorption for the Cr(VI) ions in the presence of competing ions. Thermodynamic studies revealed that the adsorption process was exothermic (\(\Delta H\)?<?0) and spontaneous (\(\Delta G\)?<?0). In addition, the spent MIIP can be regenerated up to five cycles without a significant decrease in adsorption capacity.     

Adsorption of Pb2+ and Cd2+ on the l-cysteine-functionalized graphene oxide/chitosan/polyvinyl alcohol hydrogel: Kinetic,isotherm, and thermodynamic study

In this study, polyvinyl alcohol-chitosan-cysteine-functionalized graphene oxide (PCCFG) hydrogel was synthesized from l -cysteine-functionalized graphene oxide (CFG), chitosan (CS), and polyvinyl alcohol (PVA). The hydrogel was characterized by Fourier transform infrared spectroscopy, scanning electron microscopy, and energy-dispersive X-ray spectroscopy and employed for removing lead ion (Pb²⁺) and cadmium ion (Cd²⁺) from aqueous solution. The effects of initial metal ion concentration, hydrogel dose, pH, time, and temperature were studied. The experimental data were well described by a pseudo-second-order kinetic model and Langmuir isotherm with maximum adsorption capacities of 250 and 192 mg g⁻¹ at 25°C for Pb²⁺ and Cd²⁺, respectively. The adsorption capacity of the PCCFG hydrogel increased with an increase in temperature. The value of ∆G° was negative, which shows the spontaneity of the reaction (electron exchange or ion exchange) between the metal ion and electron-rich atoms (–N, –S, –O). The positive ∆H° shows that the adsorption reaction consumes energy and the positive ∆S° shows the strong affinity of PCCFG toward the Pb²⁺ and Cd²⁺ ions. Pb²⁺ had better affinity and less spontaneity than Cd²⁺. The results show that the coexistence of Pb²⁺, Cd²⁺, and Cu²⁺ in the solution inhibits the adsorption capacity of PCCFG.     

Leaching of heavy metals from solidified waste using Portland cement and zeolite as a binder

This study investigated the properties of solidified waste using ordinary Portland cement (OPC) containing synthesized zeolite (SZ) and natural zeolite (NZ) as a binder. Natural and synthesized zeolites were used to partially replace the OPC at rates of 0%, 20%, and 40% by weight of the binder. Plating sludge was used as contaminated waste to replace the binder at rates of 40%, 50% and 60% by weight. A water to binder (w/b) ratio of 0.40 was used for all of the mixtures. The setting time and compressive strength of the solidified waste were investigated, while the leachability of the heavy metals was determined by TCLP. Additionally, XRD, XRF, and SEM were performed to investigate the fracture surface, while the pore size distribution was analyzed with MIP. The results indicated that the setting time of the binders marginally increased as the amount of SZ and NZ increased in the mix. The compressive strengths of the pastes containing 20 and 40wt.% of NZ were higher than those containing SZ. The compressive strengths at 28 days of the SZ solidified waste mixes were 1.2-31.1MPa and those of NZ solidified waste mixes were 26.0-62.4MPa as compared to 72.9MPa of the control mix at the same age. The quality of the solidified waste containing zeolites was better than that with OPC alone in terms of the effectiveness in reducing the leachability. The concentrations of heavy metals in the leachates were within the limits specified by the US EPA. SEM and MIP revealed that the replacement of Portland cement by zeolites increased the total porosity but decreased the average pore size and resulted in the better containment of heavy ions from the solidified waste.