Turbulence and turbulent flux events in a small estuary

Relatively little systematic research has been conducted on the turbulence characteristics of small estuaries. In the present study, detailed measurements were conducted in a small subtropical estuary with a focus on turbulent flux events. Acoustic Doppler velocimeters were installed in the mid-estuary at fixed locations and sampled simultaneously and continuously for 50 h. A turbulent flux event analysis was performed for the entire data sets extending the technique of Narasimha et al. (Phil Trans R Soc Ser A 365:841–858, 2007) to the unsteady open channel flow motion and to turbulent sub-events. Turbulent bursting events were defined in terms of the instantaneous turbulent flux. The data showed close results for all ADV units. The very-large majority of turbulent events lasted between 0.04 and 0.3 s with an average of 1 to 4 turbulent events observed per second. A number of turbulent bursting events consisted of consecutive turbulent sub-events, with between 1 and 3 sub-events per main event on average. For all ADV systems, the number of events, event duration and event amplitude showed some tidal trends, with basic differences between high- and low-water periods. A comparison between the present estuary data and the atmospheric boundary layer results of Narasimha et al. (Phil Trans R Soc Ser A 365:841–858, 2007) showed a number of similarities and demonstrated the significance of turbulent events in environmental flows. A burstiness index of 0.85 was found for the present data.     

Experimental assessment of characteristic turbulent scales in two-phase flow of hydraulic jump: from bottom to free surface

A hydraulic jump is a turbulent shear flow with a free-surface roller. The turbulent flow pattern is characterised by the development of instantaneous three-dimensional turbulent structures throughout the air–water column up to the free surface. The length and time scales of the turbulent structures are key information to describe the turbulent processes, which is of significant importance for the improvement of numerical models and physical measurement techniques. However, few physical data are available so far due to the complexity of the measurement. This paper presents an investigation of a series of characteristic turbulent scales for hydraulic jumps, covering the length and time scales of turbulent flow structures in bubbly flow, on free surface and at the impingement point. The bubbly-flow turbulent scales are obtained for Fr = 7.5 with 3.4 × 10⁴ < Re < 1.4 × 10⁵ in both longitudinal and transverse directions, and are compared with the free-surface scales. The results highlight three-dimensional flow patterns with anisotropic turbulence field. The turbulent structures are observed with different length and time scales respectively in the shear flow region and free-surface recirculation region. The bubbly structures next to the roller surface and the free-surface fluctuation structures show comparable length and time scales, both larger than the scales of vortical structures in the shear flow and smaller than the scales of impingement perimeter at the jump toe. A decomposition of physical signals indicates that the large turbulent scales are related to the unsteady motion of the flow in the upper part of the roller, while the high-frequency velocity turbulence dominates in the lower part of the roller. Scale effects cannot be ignored for Reynolds number smaller than 4 × 10⁴, mainly linked to the formation of large eddies in the shear layer. The present study provides a comprehensive assessment of turbulent scales in hydraulic jump, including the analyses of first data set of longitudinal bubbly-flow integral scales and transverse jump toe perimeter integral scales.     

Modelling of turbulent dispersion for numerical simulation of wind-driven rain on bridges

Wind-driven rain (WDR) is responsible for many potential negative effects on bridges, such as structural cracking, aggregate erosion, steel corrosion and storm water management problems and so on. Hence, accurate evaluations of the WDR effects on bridges are essential to provide solutions for preventing material degradation and improving durability capability of bridges. However, in most previous WDR numerical studies, the turbulent dispersion of raindrops was neglected. In this paper, the turbulent dispersion is integrated into Eulerian multiphase model to investigate the WDR effects on a bridge with rectangular cross-section. Especially, the influences of the turbulent dispersion are discussed in detail by comparing the WDR simulation results for the cases with and without consideration of the turbulent dispersion in terms of WDR flow fields, volume fraction, specific catch ratio, catch ratio, rain loads and aerostatic force coefficients. The results indicate that the turbulent dispersion for a certain range of raindrop size is needed to be taken into account for obtaining accurate WDR simulation results for bridges.     

Clustering of aerosols in atmospheric turbulent flow

A mechanism of formation of small-scale inhomogeneities in spatial distributions of aerosols and droplets associated with clustering instability in the atmospheric turbulent flow is discussed. The particle clustering is a consequence of a spontaneous breakdown of their homogeneous space distribution due to the clustering instability, and is caused by a combined effect of the particle inertia and a finite correlation time of the turbulent velocity field. In this paper a theoretical approach proposed in Elperin et al. (2002) Phys Rev E 66:036302 is further developed and applied to investigate the mechanisms of formation of small-scale aerosol inhomogeneities in the atmospheric turbulent flow. The theory of the particle clustering instability is extended to the case when the particle Stokes time is larger than the Kolmogorov time scale, but is much smaller than the correlation time at the integral scale of turbulence. We determined the criterion of the clustering instability for the Stokes number larger than 1. We discussed applications of the analyzed effects to the dynamics of aerosols and droplets in the atmospheric turbulent flow.     

Turbulence and aeration in hydraulic jumps: free-surface fluctuation and integral turbulent scale measurements

In an open channel, a change from a supercritical to subcritical flow is a strong dissipative process called a hydraulic jump. Herein some new measurements of free-surface fluctuations of the impingement perimeter and integral turbulent time and length scales in the roller are presented with a focus on turbulence in hydraulic jumps with a marked roller. The observations highlighted the fluctuating nature of the impingement perimeter in terms of both longitudinal and transverse locations. The results showed further the close link between the production and detachment of large eddies in jump shear layer, and the longitudinal fluctuations of the jump toe. They highlighted the importance of the impingement perimeter as the origin of the developing shear layer and a source of vorticity. The air–water flow measurements emphasised the intense flow aeration. The turbulent velocity distributions presented a shape similar to a wall jet solution with a marked shear layer downstream of the impingement point. The integral turbulent length scale distributions exhibited a monotonic increase with increasing vertical elevation within 0.2 < L_z/d₁ < 0.8 in the shear layer, where L_z is the integral turbulent length scale and d₁ the inflow depth, while the integral turbulent time scales were about two orders of magnitude smaller than the period of impingement position longitudinal oscillations.     

Prediction of mass and momentum transport in turbulent plane wall jets over smooth and transitionally rough surfaces

This paper is concerned with the prediction of mass and momentum transport in turbulent wall jets developing over smooth and transitionally rough plane walls. The ability to accurately predict the resulting wall shear stresses and vertical profiles of the Reynolds stresses in these flows is prerequisite to the accurate prediction of bed scour, sediment re-suspension and transport by turbulent diffusion. The computations were performed by solving the Reynolds-averaged forms of the equations describing conservation of mass, momentum and concentration. The unknown correlations that arise from the averaging process (the Reynolds stresses in the case of the momentum equation, and the turbulent mass fluxes in the case of concentration) were obtained from the solution of modeled differential equations that describe their conservation. Since these models are somewhat more complex than those typically used in practice, their benefits are demonstrated by comparisons with results obtained from simpler, eddy-viscosity based closures. Comparisons with experimental data show that results of acceptable accuracy can be obtained only by using the appropriate combination of models for the turbulent fluxes of mass and momentum that properly account for the reduction of the Reynolds stresses due to wall damping effects, and for the modification of the mass transfer rates due to interactions with the mean rates of strain.     

Surface signatures of submerged heated jet

The flow induced at the surface of a water body by a submerged heated horizontal turbulent jet was investigated experimentally with the aim of developing parameterizations for surface mean temperature/velocity fields. The jet nozzle diameter was fixed, the depth of the jet beneath the free surface was varied, and two jet Reynolds numbers (5020, 11300) were considered. The surface temperature was measured using a highly sensitive infrared camera, and the near-surface horizontal velocity field was measured using particle image velocimetry. The experimental results were explained using a model based on similarity solutions with variable turbulent viscosity. While classical Schlichting’s solution with constant turbulent viscosity predicts complete similarity for transverse velocity/temperature distributions only in a plane that coincides with the flow axis, the present solution predicts similarity in an arbitrary plane parallel to the flow axis, which was confirmed using data collected at the surface. Comparisons of present data with available previous results also showed general agreement.     

Effects of water motion and prey behavior on zooplankton capture by two coral reef fishes

Water motion is an important factor affecting planktivory on coral reefs. The feeding behavior of two species of tube-dwelling coral reef fish (Chaenopsidae) was studied in still and turbulent water. One species of blenny, Acanthemblemaria spinosa , lives in holes higher above the reef surface and feeds mainly on calanoid copepods, while a second, A. aspera , lives closer to the reef surface, feeds mainly on harpacticoid copepods, and is exposed to less water motion than the first. In the laboratory, these two blenny species were video recorded attacking a calanoid copepod ( Acartia tonsa, evasive prey) and an anostracan branchiopod (nauplii of Artemia sp., passive prey). Whereas A. spinosa attacked with the same vigor in still and turbulent water, A. aspera modulated its attack with a more deliberate strike under still conditions than turbulent conditions. For both fish species combined, mean capture success when feeding on Artemia sp. was 100% in still water and dropped to 78% in turbulent water. In contrast, when feeding on Acartia tonsa, mean capture success was 21% in still water and rose to 56% in turbulent water. We hypothesize that, although turbulence reduces capture success by adding erratic movement to Artemia sp. (passive prey), it increases capture success of Acartia tonsa (evasive prey) by interfering with the hydrodynamic sensing of the approaching predator. These opposite effects of water motion increase the complexity of the predator-prey relationship as water motion varies spatially and temporally on structurally complex coral reefs. Some observations were consistent with A. aspera living in a lower energy benthic boundary layer as compared with A. spinosa: slower initial approach to prey, attack speeds modulated according to water velocity, and lower proportion of approaches that result in strikes in turbulent water.Communicated by P.W. Sammarco, Chauvin     

Turbulence measurements in a small subtropical estuary under king tide conditions

In natural waterways and estuaries, the understanding of turbulent mixing is critical to the knowledge of sediment transport, stormwater runoff during flood events, and release of nutrient-rich wastewater into ecosystems. In the present study, some field measurements were conducted in a small subtropical estuary with micro-tidal range and semi-diurnal tides during king tide conditions: i.e., the tidal range was the largest for both 2009 and 2010. The turbulent velocity measurements were performed continuously at high-frequency (50Hz) for 60?h. Two acoustic Doppler velocimeters (ADVs) were sampled simultaneously in the middle estuarine zone, and a third ADV was deployed in the upper estuary for 12?h only. The results provided an unique characterisation of the turbulence in both middle and upper estuarine zones under the king tide conditions. The present observations showed some marked differences between king tide and neap tide conditions. During the king tide conditions, the tidal forcing was the dominant water exchange and circulation mechanism in the estuary. In contrast, the long-term oscillations linked with internal and external resonance played a major role in the turbulent mixing during neap tides. The data set showed further that the upper estuarine zone was drastically less affected by the spring tide range: the flow motion remained slow, but the turbulent velocity data were affected by the propagation of a transient front during the very early flood tide motion at the sampling site.     

Turbulent velocity profile in fully-developed open channel flows

The determination of velocity profile in turbulent narrow open channels is a difficult task due to the significant effects of the anisotropic turbulence that involve the Prandtl’s second type of secondary flow occurring in the cross section. With these currents the maximum velocity appears below the free surface that is called dip phenomenon. The well-known logarithmic law describes the velocity distribution in the inner region of the turbulent boundary layer but it is not adapted to define the velocity profile in the outer region of narrow channels. This paper relies on an analysis of the Navier–Stokes equations and yields a new formulation of the vertical velocity profile in the center region of steady, fully developed turbulent flows in open channels. This formulation is able to predict time averaged primary velocity in the outer region of the turbulent boundary layer for both narrow and wide open channels. The proposed law is based on the knowledge of the aspect ratio and involves a parameter C_Ar depending on the position of the maximum velocity (ξ_dip). ξ_dip may be derived, either from measurements or from an empirical equation given in this paper. A wide range of longitudinal velocity profile data for narrow open channels has been used for validating the model. The agreement between the measured and the computed velocities is rather good, despite the simplification used.     

Subgrid-Scale Modeling of Reacting Scalar Fluxes in Large-Eddy Simulations of Atmospheric Boundary Layers

In large-eddy simulations of atmospheric boundary layer turbulence, the lumped coefficient in the eddy-diffusion subgrid-scale (SGS) model is known to depend on scale for the case of inert scalars. This scale dependence is predominant near the surface. In this paper, a scale-dependent dynamic SGS model for the turbulent transport of reacting scalars is implemented in large-eddy simulations of a neutral boundary layer. Since the model coefficient is computed dynamically from the dynamics of the resolved scales, the simulations are free from any parameter tuning. A set of chemical cases representative of various turbulent reacting flow regimes is examined. The reactants are involved in a first-order reaction and are injected in the atmospheric boundary layer with a constant and uniform surface flux. Emphasis is placed on studying the combined effects of resolution and chemical regime on the performance of the SGS model. Simulations with the scale-dependent dynamic model yield the expected trends of the coefficients as function of resolution, position in the flow and chemical regime, leading to resolution-independent turbulent reactant fluxes.     

A closure approach with multi-scale mixing length,and its application to wind and shear stress profiles within the atmospheric boundary layer

A method to determine flow specific first-order closure for the turbulent flux of momentum in the atmospheric boundary layer (ABL) is presented. This is based on the premise that eddy viscosity is a flow rather than a fluid property, and the physically more realistic assumption that the transfer of momentum and other scalar quantities in a turbulent flow takes place by a large, but finite number of length scales, than the often used single length scale, the ‘mixing length’. The resulting eddy viscosity is flow specific and when applied to the study of the ABL, yields the vertical profiles of shear stress and mean wind velocity in good agreement with observations. The method may be extended to other types of turbulent flows, however it should be recognized that each type of flow may yield a different eddy viscosity profile. Using the derived eddy viscosity the paper presents simple analytical solutions of the ABL equations to determine observationally consistent wind speed and shear stress profiles in the ABL for a variety of practical applications including air pollution modelling.     

RANS-based simulation of transverse turbulent mixing in a 2D geometry

Although transverse mixing is a significant process in river engineering when dealing with the discharge of pollutants from point sources or the mixing of tributary inflows, no theoretical basis exists for the prediction of its rate, which is indeed based upon the results of experimental works carried on in laboratory channels or in streams and rivers. The paper presents the preliminary results of a numerical study undertaken to simulate the transverse mixing of a steady-state point source of a tracer in a two-dimensional rectangular geometry, which is expected to reproduce a shallow flow. This geometry is that of Lau and Krishnappan (J Hydraul Div 13(HY10):1173–1189, 1977), who collected turbulent mixing data for a shallow flow. In the numerical study an approach based on the Reynolds Averaged Navier–Stokes (RANS) equations was applied, where the closure problem was solved by using turbulent viscosity concept. Particularly, the classical two-equations k–? model was used. Two methods were applied to the model results to evaluate the turbulent transverse mixing coefficient. The effect on transverse mixing of a grid located upstream the tracer source was also studied. Numerical results were generally higher than the experimental data. This overestimation could be explained considering the hypothesis of isotropic turbulence underlying the k–? model, which can lead to large turbulent viscosities and rate of mixing. However, RANS-based results may still be considered acceptable also providing the large uncertainties associated with literature predictive equations.     

Large eddy simulation of flow and scalar transport in a vegetated channel

Predicting flow and mass transport in vegetated regions has a broad range of applications in ecology and engineering practice. This paper presents large eddy simulation (LES) of turbulent flow and scalar transport within a fully developed open-channel with submerged vegetation. To properly represent the scalar transport, an additional diffusivity was introduced within the canopy to account for the contribution of stem wakes, which were not resolved by the LES, to turbulent diffusion. The LES produced good agreement with the velocity and concentration fields measured in a flume experiment. The simulation revealed a secondary flow distributed symmetrically about the channel centerline, which differed significantly from the circulation in a bare channel. The secondary circulation accelerated the vertical spread of the plume both within and above the canopy layer. Quadrant analysis was used to identify the form and shape of canopy-scale turbulent structures within and above the vegetation canopy. Within the canopy, sweep events contributed more to momentum transfer than ejection events, whereas the opposite occurred above the canopy. The coherent structures were similar to those observed in terrestrial canopies, but smaller in scale due to the constraint of the water surface.     

Large Eddy Simulation of turbulence generated by a weak breaking tidal bore

A tidal bore is a natural and fragile phenomenon, which is of great importance for the ecology of an estuary. The bore development is closely linked with the tidal range and the river mouth shape, and its existence is sensitive to any small change in boundary conditions. Despite their ecological and cultural value, little is known on the flow field, turbulent mixing and sediment motion beneath tidal bores. Indeed, some striking features can be highlighted in two-dimensional simulations, such as large velocity fluctuations and flow recirculation structures. Using Large Eddy Simulation method, the numerical results emphasised the complicated turbulent structures and their unsteadiness under a tidal bore.     

The energy balance closure problem: an overview

This paper gives an overview of 20 years of research on the energy balance closure problem. It will be shown that former assumptions that measuring errors or storage terms are the reason for the unclosed energy balance do not stand up because even turbulent fluxes derived from documented methods and calibrated sensors, net radiation, and ground heat fluxes cannot close the energy balance. Instead, exchange processes on larger scales of the heterogeneous landscape have a significant influence. By including these fluxes, the energy balance can be approximately closed. Therefore, the problem is a scale problem and has important consequences to the measurement and modeling of turbulent fluxes.     

Eulerian and Lagrangian time scales of the turbulence above staggered arrays of cubical obstacles

Environmental Fluid Mechanics - We present results from water-channel experiments on neutrally-stable turbulent flows over staggered arrays of cubical obstacles modelling idealised urban canopies....     

Spatial characteristics of turbulent organized structures within the roughness sublayer over idealized urban surface with obstacle-height variability

Environmental Fluid Mechanics - The effects of obstacle-height variability on spatial characteristics of turbulent organized structures were investigated with the use of a large-eddy simulation...     

Roof-level large- and small-scale coherent structures in a street canyon flow

Environmental Fluid Mechanics - The characteristics of large- and small-scale turbulent motions at roof-level in a street canyon flow were experimentally investigated along with their...