Hydrogeo-chemical impacts of air sparging remediation on a semi-confined aquifer: Evidences from field monitoring and modeling

Air sparging (AS) was explored for remediation of a petroleum contaminated semi-confined groundwater system in NE China. Physical, hydro-chemical and hydraulic behaviors in subsurface environment during AS were investigated with support of modeling to understand the hydrogeo-chemical impacts of AS on the aquifer. The responses of groundwater, dissolved oxygen and temperature indicated that the radius of influence of AS was up to 8–9 m, and a 3D boundary of the zone of influence (ZOI) was accordingly obtained with volume of 362 m³. Water mounding unlike normal observations was featured by continuous up-lift and blocked dissipation. AS induced water displacement was calculated showing no obvious spreading of contaminant plume under this AS condition. Slug tests were employed before and after AS to reveal that the physical perturbation led to sharp increase in permeability and porosity. Modeling indicated that the regional groundwater flow field was not affected by AS except the physical perturbation in ZOI. Hydro-chemically increase of pH and Eh, and reduction of TDS, electrical conductivity and bicarbonate were observed in ZOI during AS. PHREEQC modeling inferred that these chemical phenomena were induced by the inorganic carbon transfer during air mixing.     

Air–water exchange fluxes of polycyclic aromatic hydrocarbons in the tropical coast,Taiwan

Air–water exchange fluxes of polycyclic aromatic hydrocarbons (PAHs) were simultaneously measured in air and water samples from two sites on the Kenting coast, located at the southern tip of Taiwan, from January to December 2010. There was no significant difference in the total PAH (t-PAH) concentrations in both gas and dissolved phases between these two sites due to the less local input which also coincided to the low levels of t-PAH concentration; the gas and dissolved phases averaged 1.29 ± 0.59 ng m^?3 and 2.17 ± 1.19 ng L^?1 respectively. The direction and magnitude of the daily flux of PAHs were significantly influenced by wind speed and dissolved PAH concentrations. Individual PAH flux ranged from 627 ng m^?2 d^?1 volatilization of phenanthrene during the rainy season with storm–water discharges raising dissolved phase concentration, to 67 ng m^?2 d^?1 absorption of fluoranthene during high wind speed periods. Due to PAH annual fluxes through air–water exchange, Kenting seawater is a source of low molecular weight PAHs and a reservoir of high molecular weight PAHs. Estimated annual volatilization fluxes ranged from 7.3 μg m^?2 yr^?1 for pyrene to 50 μg m^?2 yr^?1 for phenanthrene and the absorption fluxes ranged from ?2.6 μg m^?2 yr^?1 for chrysene to ?3.5 μg m^?2 yr^?1 for fluoranthene.     

Quantifying RDX biodegradation in groundwater using δ15N isotope analysis

Isotope analysis was used to examine the extent of hexahydro-1,3,5-trinitro-1,3,5-triazine (RDX) biodegradation in groundwater along a ca. 1.35-km contamination plume. Biodegradation was proposed as a natural attenuating remediation method for the contaminated aquifer. By isotope analysis of RDX, the extent of biodegradation was found to reach up to 99.5% of the initial mass at a distance of 1.15–1.35 km down gradient from the contamination sources. A range of first-order biodegradation rates was calculated based on the degradation extents, with average half-life values ranging between 4.4 and 12.8 years for RDX biodegradation in the upper 15 m of the aquifer, assuming purely aerobic biodegradation, and between 10.9 and 31.2 years, assuming purely anaerobic biodegradation. Based on the geochemical data, an aerobic biodegradation pathway was suggested as the dominant attenuation process at the site. The calculated biodegradation rate was correlated with depth, showing decreasing degradation rates in deeper groundwater layers. Exceptionally low first-order kinetic constants were found in a borehole penetrating the bottom of the aquifer, with half life ranging between 85.0 to 161.5 years, assuming purely aerobic biodegradation, and between 207.5 and 394.3 years, assuming purely anaerobic biodegradation.The study showed that stable isotope fractionation analysis is a suitable tool to detect biodegradation of RDX in the environment. Our findings clearly indicated that RDX is naturally biodegraded in the contaminated aquifer. To the best of our knowledge, this is the first reported use of RDX isotope analysis to quantify its biodegradation in contaminated aquifers.     

Carbonyl sulphide in and over seawater: summer data from the northeast Atlantic Ocean

Carbonyl sulphide (COS) concentrations in air and dissolved in seawater were determined during a cruise in summer 1997 in the northeast Atlantic Ocean. Seawater characteristics and meteorological parameters were monitored. Dissolved COS concentrations throughout the entire cruise exhibited a strong diel cycle with maximum concentrations in late afternoon and minimum concentrations at sunrise. This is in good agreement with the theory that COS is photochemically produced from dissolved organic matter during the day and removed by hydrolysis. The overall mean concentration of dissolved COS was 23.6 pmol dm^-3; the daily mean varied according to water mass characteristics and was highest in upwelling areas owing to increased dissolved organic matter. Atmospheric COS concentrations, varying from about 450 to 800 pptv with an average value of 657 pptv, showed some dependency on air mass history and local COS flux from the sea surface. The exchange of COS between the ocean and the atmosphere depended on dissolved COS concentrations and wind speed. The daily integrated flux was always from the sea into the air, and the average was 1.3±0.8 g COS km^-2 d^-2. The collected data were used to test a mixed layer box model and a one-dimensional model, both describing the behaviour of COS in seawater. We found that the one-dimensional model simulates the data more closely, especially during the night.     

Dissolved black carbon in grassland streams: Is there an effect of recent fire history?

While the existence of black carbon as part of dissolved organic matter (DOM) has been confirmed, quantitative determinations of dissolved black carbon (DBC) in freshwater ecosystem and information on factors controlling its concentration are scarce. In this study, stream surface water samples from a series of watersheds subject to different burn frequencies in Konza Prairie (Kansas, USA) were collected in order to determine if recent fire history has a noticeable effect on DBC concentration. The DBC levels detected ranged from 0.04 to 0.11 mg L^?1, accounting for ca. 3.32 ± 0.51% of dissolved organic carbon (DOC). No correlation was found between DBC concentration and neither fire frequency nor time since last burn. We suggest that limited DBC flux is related to high burning efficiency, possibly greater export during periods of high discharge and/or the continuous export of DBC over long time scales. A linear correlation between DOC and DBC concentrations was observed, suggesting the export mechanisms determining DOC and DBC concentrations are likely coupled. The potential influence of fire history was less than the influence of other factors controlling the DOC and DBC dynamics in this ecosystem. Assuming similar conditions and processes apply in grasslands elsewhere, extrapolation to a global scale would suggest a global grasslands flux of DBC on the order of 0.14 Mt carbon year^?1.     

Atmospheric distribution of polycyclic aromatic hydrocarbons and deposition to Galveston Bay,Texas, USA

Estimates of the atmospheric deposition to Galveston Bay of polycyclic aromatic hydrocarbons (PAHs) are made using precipitation and meteorological data that were collected continuously from 2 February 1995 to 6 August 1996 at Seabrook, TX, USA. Particulate and vapor phase PAHs in ambient air and particulate and dissolved phases in rain samples were collected and analyzed. More than 95% of atmospheric PAHs were in the vapor phase and about 73% of PAHs in the rain were in the dissolved phase. Phenanthrene and napthalene were the dominant compounds in air vapor and rain dissolved phases, respectively, while 5 and 6 ring PAH were predominant in the particulate phase of both air and rain samples. Total PAH concentrations ranged from 4 to 161 ng m⁻³ in air samples and from 50 to 312 ng l⁻¹ in rain samples. Temporal variability in total PAH air concentrations were observed, with lower concentrations in the spring and fall (4–34 ng m ⁻³) compared to the summer and winter (37–161 ng m⁻³). PAHs in the air near Galveston Bay are derived from both combustion and petroleum vaporization. Gas exchange from the atmosphere to the surface water is estimated to be the major deposition process for PAHs (1211 μg m^{− 2} yr^{− 1}), relative to wet deposition (130 μg m⁻² yr^{− 1}) and dry deposition (99 μg m⁻² yr^{− 1}). Annual deposition of PAHs directly to Galveston Bay from the atmosphere is estimated as 2  t yr⁻¹.     

Pre- and post-catalyst-, fuel-, velocity- and acceleration-dependent benzene emission data of gasoline-driven EURO-2 passenger cars and light duty vehicles

The benzene emission characteristics of six gasoline-driven EURO-2 vehicles, three passenger cars and three light duty vehicles, have been determined by time-resolved chemical ionization mass spectrometry. Aliquots of the exhaust gas were monitored pre- and post-catalyst with two independently operating mass spectrometers. Each vehicle was driven with two different fuels having benzene contents of 1 and 2 vol%. Seven driving cycles—including the European (EDC) and the US (FTP-75) driving cycle—with a total driving time of about 8800 s were studied. Herein, we discuss the average emission characteristics of the entire fleet at transient driving in the velocity range of 0–150 km h⁻¹. The conversion efficiencies of the involved catalytic systems were deduced from the pre- and post-catalyst data. On average, the vehicles showed optimal benzene conversion efficiencies (>95%) in the velocity range of 30–90 km h⁻¹. When driving below 20 or above 100 km h⁻¹ reduced benzene conversion was found (80–82%). No benzene conversion was observed when driving above 130 km h⁻¹. In contrast, the post-catalyst benzene emissions exceeded those of the untreated exhaust gas by 19–49%. Thus on an average, benzene was formed across the catalysts under these conditions. In addition, the influence of the benzene content of the gasoline on the tail-pipe emissions was also studied. The use of the gasoline with 1 vol% benzene instead of 2 vol% induced a 20–30% reduction of the post-catalyst emissions when driving below 50 km h⁻¹. The fuel effect became smaller above 100 km h⁻¹ and was even negative at high engine load (>130 km h⁻¹). Thus under these conditions, when benzene is formed across the catalyst, the amount of the emitted benzene was independent of the benzene level of the fuel.     

Seasonal variability of formaldehyde production from photolysis of rainwater dissolved organic carbon

Photochemical production of formaldehyde (HCHO) was measured in rainwater from 13 precipitation events in Wilmington, North Carolina, USA under conditions of simulated sunlight. HCHO concentrations increased in all samples irradiated with no changes observed in dark controls. HCHO photoproduction rates were strongly correlated with dissolved organic carbon (DOC) suggesting HCHO was derived from direct or indirect photolysis of rainwater DOC. The higher photoproduction rates (0.03–2.9 μM h^?1) relative to those reported for surface waters suggests that rainwater DOC is more photolabile in terms of HCHO production than surface waters. HCHO photoproduction rates were higher in growing season (1.0 ± 1.0 μM h^?1) compared to non-growing season (0.08 ± 0.05 μM h^?1) even when rates were normalized for DOC (6.8 ± 3.6 μM h^?1 mM C^?1 versus 1.8 ± 1.0 μM h^?1 mM C^?1). The higher growing season rate may be related to seasonal differences in the composition of DOC as evidenced by differences in fluorescence per unit carbon of rainwater samples. Irradiation of C18 extracts of rainwater also produced HCHO, but at lower rates compared to corresponding whole rain samples, suggesting that hydrophyllic components of rainwater play a role in HCHO photoproduction. Our results indicate that photolysis of rainwater DOC produces significant amounts of HCHO, and possibly other low molecular weight organic compounds, likely increasing its reactivity and bioavailability.     

Kinetic aspects and identification of by-products during the ozonation of bitertanol in agricultural wastewaters

The degradation of bitertanol by ozone treatment is investigated. Solutions of bitertanol (8.4 μg mL^?1) were prepared either by dissolution of the standard or by dilution of Gaucho Blé seed loading solution and then ozonated under different conditions. Evolution of the concentrations of bitertanol and its ozonation by-products in both solutions was monitored by HPLC–UV as a function of the treatment time for a concentration of 100 g m^?3 of ozone in the inlet gas. Bitertanol degradation was found to follow a pseudo-first order reaction in both cases. However, the rate of the reaction in diluted seed loading solution was much lower (0.19 vs. 0.27 min^?1 in standard solution) and was close to the reaction rate observed in the presence of a radical scavenger, tert-butanol (0.11 min^?1). Thus, it may be suggested that additives present in the seed loading solution may play the role of radical scavengers. Study of ozone concentration in the inlet gas (from 25 to 100 g m^?3) showed that ozone degradation is also a first-order reaction with respect to ozone. Four ozonation by-products were highlighted, collected and identified by HPLC coupled with an ion trap mass spectrometer using positive electrospray ionization mode. A degradation pathway of bitertanol was finally proposed.     

Contribution ratio of freely to total dissolved concentrations of polycyclic aromatic hydrocarbons in natural river waters

The bioavailability and ecological risk of hydrophobic organic compounds (HOCs) in aquatic environments largely depends on their freely dissolved concentrations. In this work, the freely dissolved concentrations of polycyclic aromatic hydrocarbons (PAHs) including phenanthrene, pyrene, and chrysene were determined for the Yellow River, Haihe River and Yongding River of China using polyethylene devices (PEDs). The results indicated that the order of ratios of freely to total dissolved concentrations of the three PAHs was phenanthrene (66.8 ± 20.1%) > pyrene (48.8 ± 26.4%) > chrysene (5.5 ± 3.3%) for the three rivers. The ratios were significantly negatively correlated with the log K_ow values of the PAHs. In addition, the ratios were negatively correlated with the suspended sediment (SPS) and dissolved organic carbon (DOC) concentrations in the river water, and the characteristics of the SPS and DOC were also important factors. Simulation experiments showed that the ratio of freely to total dissolved concentrations of pyrene in the aqueous phase decreased with increasing SPS concentration; when the sediment concentration increased from 2 g L^?1 to 10 g L^?1, the ratio decreased from 67.6% to 38.4% for Yellow River sediment and decreased from 50.4% to 33.6% for Haihe River sediment. This was because with increasing SPS concentration, more and more DOC, small particles and colloids (<0.45 μm) would enter the aqueous phase. Because high SPS and DOC concentrations exist in many rivers, their effect on the freely dissolved concentrations of HOCs should be considered when conducting an ecological risk assessment.     

Aerosol number size distributions within the exhaust plume of a diesel and a gasoline passenger car under on-road conditions and determination of emission factors

A new setup has been developed and built to measure number size distributions of exhaust particles and thermodynamic parameters under real traffic conditions. Measurements have been performed using a diesel and a gasoline passenger car driving with different speeds and engine conditions. Significant number of nucleation mode particles was found only during high load conditions, i.e. high car and engine speeds behind the diesel car. The number concentration of soot mode particles varied within a factor of two for different engine conditions while the concentration of nucleation mode particles varied up to two orders of magnitude. The results show that roadside measurements are still quite different from those behind the tailpipe. Beside dilution transformation processes within the first meter behind the tailpipe also play an important role, such as nucleation and growth. Emission factors were calculated and compared with those obtained by other studies. Emission factors for particles larger than 25 nm (primary emissions) varied within 1.1 × 10¹⁴ km^?1 and 2.7 × 10¹⁴ km^?1 for the diesel car and between 0.6 × 10¹² km^?1 and 3.5 × 10¹² km^?1 for the gasoline car. The advantage of these measurements is the exhaust dilution under atmospheric conditions and the size-resolved measurement technique to divide into primary emitted and secondary formed particles.     

Bioanalytical and instrumental analysis of estrogenic activities in drinking water sources from Yangtze River Delta

The estrogenic activities of source water from Yangtze River, Huaihe River, Taihu Lake and groundwater in Yangtze River Delta in the dry and wet season were determined by use of reporter gene assays based on African green monkey kidney (CV-1) cell lines. Higher estrogenic activities were observed in the dry season, and the estrogenic potentials in water samples from Taihu Lake were greater than other river basins. None of the samples from groundwater showed estrogen receptor (ER) agonist activity. The 17β-Estradiol (E2) equivalents (EEQs) of water samples in the dry season ranged from 9.41 × 10^?1 to 1.20 × 10¹ ng E2 L^?1. In the wet season, EEQs of all the water samples were below the detection limit as 9.00 × 10^?1 ng E2 L^?1 except for one sample from Huaihe River. The highest contribution of E2 was detected in Yangtze River as 99% of estrogenic activity. Nonylphenol (NP, 100% detection rate) and octylphenol (OP, 100% detection rate) might also be responsible for the estrogenic activities in water sources. Potential health risk induced by the estrogenic chemicals in source water may be posed to the residents through water drinking.     

Comparing the desorption and biodegradation of low concentrations of phenanthrene sorbed to activated carbon,biochar and compost

Carbonaceous soil amendments are applied to contaminated soils and sediments to strongly sorb hydrophobic organic contaminants (HOCs) and reduce their freely dissolved concentrations. This limits biouptake and toxicity, but also biodegradation. To investigate whether HOCs sorbed to such amendments can be degraded at all, the desorption and biodegradation of low concentrations of ¹⁴C-labelled phenanthrene (?5 μg L^?1) freshly sorbed to suspensions of the pure soil amendments activated carbon (AC), biochar (charcoal) and compost were compared. Firstly, the maximum abiotic desorption of phenanthrene from soil amendment suspensions in water, minimal salts medium (MSM) or tryptic soy broth (TSB) into a dominating silicone sink were measured. Highest fractions remained sorbed to AC (84 ± 2.3%, 87 ± 4.1%, and 53 ± 1.2% for water, MSM and TSB, respectively), followed by charcoal (35 ± 2.2%, 32 ± 1.7%, and 12 ± 0.3%, respectively) and compost (1.3 ± 0.21%, similar for all media). Secondly, the mineralization of phenanthrene sorbed to AC, charcoal and compost by Sphingomonas sp. 10-1 (DSM 12247) was determined. In contrast to the amounts desorbed, phenanthrene mineralization was similar for all the soil amendments at about 56 ± 11% of the initially applied radioactivity. Furthermore, HPLC analyses showed only minor amounts (<5%) of residual phenanthrene remaining in the suspensions, indicating almost complete biodegradation. Fitting the data to a coupled desorption and biodegradation model revealed that desorption did not limit biodegradation for any of the amendments, and that degradation could proceed due to the high numbers of bacteria and/or the production of biosurfactants or biofilms. Therefore, reduced desorption of phenanthrene from AC or charcoal did not inhibit its biodegradation, which implies that under the experimental conditions these amendments can reduce freely dissolved concentration without hindering biodegradation. In contrast, phenanthrene sorbed to compost was fully desorbed and biodegraded.     

Effect of short-chain organic acids and pH on the behaviors of pyrene in soil–water system

The effects of five short-chain organic acids (SCOAs) on the behaviors of pyrene in soil–water system were investigated. The influences of the quantity and species of organic acids, pH, and soil dissolved organic matter were considered. The results showed the presence of SCOAs inhibited the adsorption and promoted the desorption of pyrene in the following order: citric acid > oxalic acid > tartaric acid > lactic acid > acetic acid. The decreased extents of pyrene adsorption performance enhanced with increasing SCOA concentrations, while the decreasing rate became less pronounced at high SCOA concentrations. In the presence of organic acids, the adsorption ability of pyrene decreased with increasing pH. However, there was a slight increase of pyrene adsorption with the addition of oxalic acid, tartaric acid and citric acid above pH 8. The capacity for pyrene retention differentiated significantly between the soils with and without dissolved organic matter. The presence of SCOAs was also favorable for the decrease of pyrene adsorption on soil without dissolved organic matter. The results of this study have important implications for the remediation of persistent organic pollutants in soil and groundwater.     

Measurement of the vapor phase deposition of polychlorinated bipheyls (PCBs) using a water surface sampler

A water surface sampler (WSS) was employed in combination with greased knife-edge surface deposition plates (KSSs) to measure the vapor phase deposition rates of PCBs to the sampler at an urban site, Chicago, IL. This sampler employed a water circulation system that continuously removed deposited PCBs. Total (gas+particle) and particulate PCB fluxes were collected with the WSS and KSSs, respectively. Gas phase PCB fluxes were then calculated by subtracting the KSS fluxes (particulate) from the WSS fluxes (gas+particle). The calculated gas phase PCB fluxes averaged 830±910 ng m⁻²d⁻¹. This flux value is, in general, higher than the fluxes determined using simultaneously measured air–water concentrations in natural waters and is in the absorption direction. This difference is primarily because the PCBs were continuously removed from the WSS water keeping the water PCB concentration near zero.Concurrently, ambient air samples were collected using a modified high volume air sampler. The gas phase PCB concentrations ranged between 1.10 and 4.46 ng m⁻³ (average±SD, 2.29±1.28 ng m⁻³). The gas phase fluxes were divided by the simultaneously measured gas phase ambient concentrations to determine the overall gas phase mass transfer coefficients (MTCs) for PCBs. The average gas phase overall MTCs (K_g) for each homolog group ranged between 0.22 and 1.32 cm s⁻¹ (0.54±0.47 cm s⁻¹). The average MTC was in good agreement with those determined using similar techniques.     

Mercury emissions from automobiles using gasoline,diesel, and LPG

Mercury (Hg) emissions from gasoline, diesel, and liquefied petroleum gas (LPG) vehicles were measured and speciated (particulate, oxidized, and elemental mercury). First, three different fuel types were analyzed for their original Hg contents; 571.1±4.5 ng L⁻¹ for gasoline, 185.7±2.6 ng L⁻¹ for diesel, and 1230.3±23.5 ng L⁻¹ for LPG. All three vehicles were then tested at idling and driving modes. Hg in the exhaust gas was mostly in elemental form (Hg⁰), and no detectable levels of particulate (Hg^p) or oxidized (Hg²⁺) mercury were measured. At idling modes, Hg concentrations in the exhaust gas of gasoline, diesel, and LPG vehicles were 1.5–9.1, 1.6–3.5, and 10.2–18.6 ng m⁻³, respectively. At driving modes, Hg concentrations were 3.8–16.8 ng m⁻³ (gasoline), 2.8–8.5 ng m⁻³ (diesel), and 20.0–26.9 ng m⁻³ (LPG). For all three vehicles, Hg concentrations at driving modes were higher than at idling modes. Furthermore, Hg emissions from LPG vehicle was highest of all three vehicle types tested, both at idling and driving modes, as expected from the fact that it had the highest original fuel Hg content.     

Use of thermal desorption–gas chromatography–mass spectrometry (TD–GC–MS) on identification of odorant emission focus by volatile organic compounds characterisation

Volatile organic compounds (VOCs) from several different municipal solid wastes’ treatment plants in Mallorca (Spain) have been analysed by thermal desorption–gas chromatography–mass spectrometry (TD–GC–MS). Ambient (immission) air was collected during February and March 2011 by active sampling onto sorbents Tenax™ TA and Carboxen™ 1000. The study presents the chemical characterisation of 93 volatile organic compounds (VOCs) from an overall set of 84 immission air samples. 70 VOCs were positively identified.The linear fit for all 93 external standard calibration, from 10 mg L⁻¹ to 150 mg L⁻¹ (n = 4), was within the range 0.974 < r² < 0.998. Limits of detection of the method (LOD) for all the standards were within the range 1.1–4,213 pg, as the absolute standard amount spiked into sorbent tubes in 1 μL standard mixture (dissolved in methanol).Overall results stated systematic correlation between waste’s nature and VOCs’ air composition. Organic wastes show main contribution of terpenes, waste water sludge residues’ of reduced sulphured compounds (RSCs) and municipal solid wastes show contribution of a wide sort of VOCs. The use of a chemometric approach for variable’s reduction to 12 principal components enables evaluation of similarities and dissimilarities between facilities. PCA clearly related samples to its corresponding facility on the basis of their VOCs composition and the ambient temperature.     

Anaerobic abiotic transformations of cis-1,2-dichloroethene in fractured sandstone

A fractured sandstone aquifer at an industrial site is contaminated with trichloroethene to depths greater than 244 m. Field data indicate that trichloroethene is undergoing reduction to cis-1,2-dichloroethene (cDCE); vinyl chloride and ethene are present at much lower concentrations. Transformation of cDCE by pathways other than reductive dechlorination (abiotic and/or biotic) is of interest. Pyrite, which has been linked to abiotic transformation of chlorinated ethenes, is present at varying levels in the sandstone. To evaluate the possible role of pyrite in transforming cDCE, microcosms were prepared with groundwater, ～40 mg L^?1 cDCE + [¹⁴C]cDCE, and crushed solids (pure pyrite, pyrite-rich sandstone, or typical sandstone). During 120 d of incubation, the highest level of cDCE transformation occurred with typical sandstone (11–14% ¹⁴CO₂, 1–3% ¹⁴C-soluble products), followed by pyrite-rich sandstone (2–4% ¹⁴CO₂, 1% ¹⁴C-soluble products) and even lesser amounts with pure pyrite. These results indicate pyrite is not likely the mineral involved in transforming cDCE. A separate experiment using only typical sandstone compared the rate of cDCE transformation in non-sterilized, autoclaved, and propylene-oxide sterilized treatments, with pseudo-first order rate constants of 8.7, 5.4, and 1.0 yr^?1, respectively; however, transformation stopped after several months of incubation. Autoclaving increased the volume of pores, adsorption pore diameter, and surface area in comparison to non-sterilized typical sandstone. Nevertheless, autoclaving was less disruptive than chemical sterilization. The results provide definitive experimental evidence that cDCE undergoes anaerobic abiotic and biotic transformation in typical sandstone, with formation of CO₂ and soluble products.     

Characterizing exposure to chemicals from soil vapor intrusion using a two-compartment model

Though several different models have been developed for sub-surface migration, little attention has been given to the effect of subsurface transport on the indoor environment. Existing methods generally assume that a house is one well-mixed compartment. A two-compartment model was developed to better characterize this exposure pathway; the model treats the house as two well-mixed compartments, one for the basement and one for the remainder of the house. A field study was completed to quantify parameters associated with the two-compartment model, such as soil gas intrusion rates and basement to ground floor air exchange rates. Two residential test houses in Paulsboro, New Jersey were selected for this study. All experiments were completed using sulfur hexafluoride (SF₆) as a tracer gas. Soil gas intrusion rates were found to be highly dependent on the soil gas to basement pressure difference, varying from 0.001 m³ m⁻² h⁻¹ for a pressure drop of –0.2 Pa to 0.011 m³ m⁻² h⁻¹ for a pressure drop of –6.0 Pa. Basement ventilation rates ranged from 0.17 to 0.75 air changes per hour (ACH) for basement to ambient pressure differences ranging from –1.1 to –7.6 Pa (relative to ambient). Application of experimental results in conjunction with the two-compartment model indicate that exposures are highly dependent on gas intrusion rates, basement ventilation rate, and fraction of time spent in the basement. These results can also be significantly different when compared with the simple well-mixed house assumption.     

Diffuse source apportionment of the Po river eutrophying load to the Adriatic sea: Assessment of Lombardy contribution to Po river nutrient load apportionment by means of an integrated modelling approach

The source apportionment of the annual nutrient load carried by the Po river to the Adriatic sea has been studied.An integrated modelling approach was applied to the Lombardy plain area, which covers about 34% of the Po river watershed area and accounts for about 50% of the point sources’ loads carried by the river. To extract all the information available from direct instream measurements, two different modelling tools were alternatively used. The source apportionment was investigated considering both dry and wet weather scenarios. In order to quantify the apportionment in dry-weather conditions, the Lombardy portion of the Po river basin was modelled by using the US-EPA QUAL2E model. Such a simulation allowed to assess a significant contribution (about 50% of the total dry-weather load) of a not rain-driven diffuse pollution component (i.e. groundwater, springs, lake emissaries). Moreover, to estimate the rain-driven surface runoff contribution to the instream total load, the Lombardy plain area was also modelled by means of the US-DA SWAT model. SWAT results indicate a runoff contribution to the Po river instream total load of about 10 000 t N yr⁻¹ and 1300 t P yr⁻¹ (i.e. approximately the 10–20% of the total annual Lombardy nutrient load). At the event scale (i.e. the single rainstorm event) the runoff contribution may rise up to 30–80% of the total instream load. Finally, the total annual nitrogen load at the Po basin closure was estimated for the period 1985–2001. Out of a total annual load of 140 000 t N yr⁻¹, Lombardy accounts for 43% (point plus diffuse sources). The rain-driven diffuse sources constitute the 20% of the overall total load, the point sources account for 40%, whereas the remaining 40% is mainly constituted by “dry-weather diffuse sources” (i.e. groundwater, springs, lake emissaries).