Electrosorption and photocatalytic one-stage combined process using a new type of nanosized TiO2/activated charcoal plate electrode

In the present study, an activated charcoal (AC) plate was prepared by physical activation method. Its surface was coated with TiO₂ nanoparticles by electrophoretic deposition (EPD) method. The average crystallite size of TiO₂ nanoparticles was determined approximately 28 nm. The nature of prepared electrode was characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), and Brunauer–Emmett–Teller (BET) surface area measurement before and after immobilization. The electrosorption and photocatalytic one-stage combined process was investigated in degradation of Lanasol Red 5B (LR5B), and the effect of dye concentration, electrolyte concentration, pH, voltage, and contact time was optimized and modeled using response surface methodology (RSM) approach. The dye concentration of 30 mg L^?1, Na₂SO₄ concentration of 4.38 g L^?1, pH of 4, voltage of 250 mV, and contact time of 120 min were determined as optimum conditions. Decolorization efficiency increased in combined process to 85.65 % at optimum conditions compared to 66.03 % in TiO₂/AC photocatalytic, 20.09 % in TiO₂/AC electrosorption, and 1.91 % in AC photocatalytic processes.     

Carbofuran removal in continuous-photocatalytic reactor: Reactor optimization,rate-constant determination and carbofuran degradation pathway analysis

Carbofuran (CBF) removal in a continuous-flow photocatalytic reactor with granular activated carbon supported titanium dioxide (GAC-TiO₂) catalyst was investigated. The effects of feed flow rate, TiO₂ concentration and addition of supplementary oxidants on CBF removal were investigated. The central composite design (CCD) was used to design the experiments and to estimate the effects of feed flow rate and TiO₂ concentration on CBF removal. The outcome of CCD experiments demonstrated that reactor performance was influenced mainly by feed flow rate compared to TiO₂ concentration. A second-order polynomial model developed based on CCD experiments fitted the experimental data with good correlation (R² ～ 0.964). The addition of 1 mL min^?1 hydrogen peroxide has shown complete CBF degradation and 76% chemical oxygen demand removal under the following operating conditions of CBF ～50 mg L^?1, TiO₂ ～5 mg L^?1 and feed flow rate ～82.5 mL min^?1. Rate constant of the photodegradation process was also calculated by applying the kinetic data in pseudo-first-order kinetics. Four major degradation intermediates of CBF were identified using GC-MS analysis. As a whole, the reactor system and GAC-TiO₂ catalyst used could be constructive in cost-effective CBF removal with no impact to receiving environment through getaway of photocatalyst.     

Solar photocatalysis for treatment of Acid Yellow-17 (AY-17) dye contaminated water using Ag@TiO2 core–shell structured nanoparticles

Wastewater released from textile industries causes water pollution, and it needs to be treated before discharge to the environment by cost effective technologies. Solar photocatalysis is a promising technology for the treatment of dye wastewater. The Ag@TiO₂ nanoparticles comprising of Ag core and TiO₂ shell (Ag@TiO₂) have unique photocatalytic property of inhibition of electron–hole recombination and visible light absorption, which makes it a promising photocatalyst for use in solar photocatalysis and with higher photocatalytic rate. Therefore, in the present work, the Ag@TiO₂ nanoparticles synthesized by one pot method with postcalcination step has been used for the degradation of Acid Yellow-17 (AY-17) dye under solar light irradiation. The Ag@TiO₂ nanoparticles were characterized using thermogravimetric–differential thermal analysis, X-ray diffraction, transmission electron microscopy, selected area electron diffraction, and energy dispersive X-ray analysis. The catalyst has been found to be very effective in solar photocatalysis of AY-17, as compared to other catalysts. The effects of pH, catalyst loading, initial dye concentration, and oxidants on photocatalysis were also studied. The optimized parameters for degradation of AY-17 using Ag@TiO₂ were found to be pH?3, dye/catalyst ratio of 1:10 (g/g), and 2 g/L of (NH₄)₂S₂O₈ as oxidant. Efficient decolorization and mineralization of AY-17 was achieved. The kinetics of color, total organic carbon, and chemical oxygen demand removal followed the Langmuir–Hinshelwood model. Ag@TiO₂ catalyst can be reused thrice without much decline in efficiency. The catalyst exhibited its potential as economic photocatalyst for treatment of dye wastewater.     

Removal of anionic azo dye from aqueous solution via an adsorption–photosensitized regeneration process on a TiO2 surface

Textile dye effluents are typically characterized by strong color and recalcitrance, even at very low concentration. The process of enrichment of anionic azo dye on the surface of TiO₂ fibers followed by photosensitization degradation under ambient air conditions was extensively investigated. Adsorption isotherms and zeta potentials were used to describe the “dye/TiO₂ surface” interface, taking into account the effects of pH on the nature and population of the surface groups on the TiO₂ fibers. The extent of the photocatalytic degradation of dye on TiO₂ surface was determined by FTIR. N₂ adsorption isotherms and optical spectra were employed to investigate the effect of photosensitization. The adsorption of dyes on the TiO₂ surface occurs via electrostatic attraction through the formation of single- or multidentate-coordinated surface complexes. Almost complete photobleaching of the absorption band at 534 nm is achieved in ~4 h. Dye-sensitized TiO₂ fiber could absorb part of the visible light spectrum (λ?<?600 nm). Interfacial electron transfer can potentially alter the degradation efficiency. The regenerated TiO₂ fiber could be reused for subsequent decolorization without a decline in adsorption efficiency compared with freshly prepared TiO₂ samples, which may be attributed to preservation of the hierarchical pore structure and restoration of the original surface properties. In summary, we propose an efficient “adsorption–photoregeneration–reuse” process applying TiO₂ fibers for the degradation of dyes in water.     

Solar photocatalytic degradation of mono azo methyl orange and diazo reactive green 19 in single and binary dye solutions: adsorbability vs photodegradation rate

The objective of this study was to examine the effects of adsorbability and number of sulfonate group on solar photocatalytic degradation of mono azo methyl orange (MO) and diazo Reactive Green 19 (RG19) in single and binary dye solutions. The adsorption capacity of MO and RG19 onto the TiO₂ was 16.9 and 26.8 mg/g, respectively, in single dye solution, and reduced to 5.0 and 23.1 mg/g, respectively, in the binary dye solution. The data obtained for photocatalytic degradation of MO and RG19 in single and binary dye solution were well fitted with the Langmuir–Hinshelwood kinetic model. The pseudo-first-order rate constants of diazo RG19 were significant higher than the mono azo MO either in single or binary dye solutions. The higher number of sulfonate group in RG19 contributed to better adsorption capacity onto the surface of TiO₂ than MO indicating greater photocatalytic degradation rate.     

Solar CPC pilot plant photocatalytic degradation of bisphenol A in waters and wastewaters using suspended and supported-TiO2. Influence of photogenerated species

Photocatalytic degradation of bisphenol A (BPA) in waters and wastewaters in the presence of titanium dioxide (TiO₂) was performed under different conditions. Suspensions of the TiO₂ were used to compare the degradation efficiency of BPA (20 mg L^?1) in batch and compound parabolic collector (CPC) reactors. A TiO₂ catalyst supported on glass spheres was prepared (sol–gel method) and used in a CPC solar pilot plant for the photodegradation of BPA (100 μg L^?1). The influence of OH·, O₂ ^·?, and h ⁺ on the BPA degradation were evaluated. The radicals OH· and O₂ ^·? were proved to be the main species involved on BPA photodegradation. Total organic carbon (TOC) and carboxylic acids were determined to evaluate the BPA mineralization during the photodegradation process. Some toxicological effects of BPA and its photoproducts on Eisenia andrei earthworms were evaluated. The results show that the optimal concentration of suspended TiO₂ to degrade BPA in batch or CPC reactors was 0.1 g L^?1. According to biological tests, the BPA LC₅₀ in 24 h for E. andrei was of 1.7?×?10^?2 mg cm^?2. The photocatalytic degradation of BPA mediated by TiO₂ supported on glass spheres suffered strong influence of the water matrix. On real municipal wastewater treatment plant (MWWTP) secondary effluent, 30 % of BPA remains in solution; nevertheless, the method has the enormous advantage since it eliminates the need of catalyst removal step, reducing the cost of treatment.     

Influence of operational key parameters on the photocatalytic decolorization of Rhodamine B dye using Fe2+/H2O2/Nb2O5/UV system

The present research deals with the development of a new heterogeneous photocatalysis and Fenton hybrid system for the removal of color from textile dyeing wastewater as Rhodamine B (RhB) solutions by using Fe²⁺/H₂O₂/Nb₂O₅ as a photocatalytic system. The application of this photocatalytic system for the decolorization of dye contaminants is not reported in the literature yet. Different parameters like dye concentration, Nb₂O₅/Fe²⁺ catalyst amount, pH, and H₂O₂ concentration have been studied. The optimum conditions for the decolorization of the dye were initial concentration of 10 mg L^?1 of dye, pH 4, and Nb₂O₅/Fe²⁺ catalyst concentration of 0.5 g L^?1/50 mg L^?1. The optimum value of H₂O₂ concentration for the conditions used in this study was 700 mg L^?1. Moreover, the efficiency of the Nb₂O₅/photo-Fenton hybrid process in comparison to photo-Fenton alone and a dark Fenton process as a control experiment to decolorize the RhB solution has been investigated. The combination of photo-Fenton and Nb₂O₅ catalysts has been proved to be the most effective for the treatment of such type of wastewaters. The results revealed that the RhB dye was decolorized in a higher percent (78 %) by the Nb₂O₅/photo-Fenton hybrid process (Fe²⁺/H₂O₂/Nb₂O₅/UV) than by the photo-Fenton process alone (37 %) and dark Fenton process (14 %) after 120 min of treatment. Moreover, the Nb₂O₅ catalyst as a heterogeneous part of the photocatalytic system was demonstrated to have good stability and reusability.     

Photoassisted and photocatalytic degradation of sulfur mustard using TiO2 nanoparticles and polyoxometalates

The decomposition of highly toxic chemical warfare agent, sulfur mustard (bis(2-chloroethyl) sulfide or HD), has been studied by homogeneous photolysis and heterogeneous photocatalytic degradation on titania nanoparticles. Direct photolysis degradation of HD with irradiation system was investigated. The photocatalytic degradation of HD was investigated in the presence of TiO₂ nanoparticles and polyoxometalates embedded in titania nanoparticles in liquid phase at room temperature (33?±?2 °C). Degradation products during the treatment were identified by gas chromatography–mass spectrometry. Whereas apparent first-order kinetics of ultraviolet (UV) photolysis were slow (0.0091 min^?1), the highest degradation rate is obtained in the presence of TiO₂ nanoparticles as nanophotocatalyst. Simultaneous photolysis and photocatalysis under the full UV radiation leads to HD complete destruction in 3 h. No degradation products observed in the presence of nanophotocatalyst without irradiation in 3 h. It was found that up to 90 % of agent was decomposed under of UV irradiation without TiO₂, in 6 h. The decontamination mechanisms are often quite complex and multiple mechanisms can be operable such as hydrolysis, oxidation, and elimination. By simultaneously carrying out photolysis and photocatalysis in hexane, we have succeeded in achieving faster HD decontamination after 90 min with low catalyst loading. TiO₂ nanoparticles proved to be a superior photocatalyst under UV irradiation for HD decontamination.     

Effective photodegradation of methomyl pesticide in concentrated solutions by novel enhancement of the photocatalytic activity of TiO2 using CdSO4 nanoparticles

Annihilation of electrons–holes recombination process is the main remedy to enhance the photocatalytic activity of the semiconductors photocatalysts. Doping of this class of photocatalysts by foreign nanoparticles is usually utilized to create high Schottky barrier that facilitates electron capture. In the literature, because nonpolar nanoparticles (usually pristine metals, e.g., Ag, Pt, Au, etc.) were utilized in the doping process, the corresponding improvement was relatively low. In this study, CdSO₄-doped TiO₂ nanoparticles are introduced as a powerful and reusable photocatalyst for the photocatalytic degradation of methomyl pesticide in concentrated aqueous solutions. The utilized CdSO₄ nanoparticles form polar grains in the TiO₂ matrix due to the electrons leaving characteristic of the sulfate anion. The introduced nanoparticles could successfully eliminate the harmful pesticide under the sunlight radiation within a very short time (less than 1 h), with a removal capacity reaching 1,000 mg pesticide per gram of the introduced photocatalyst. Moreover, increase in the initial concentration of the methomyl did not affect the photocatalytic performance; typically 300, 500, 1,000, and 2,000 mg/l solutions were completely treated within 30, 30, 40, and 60 min, respectively, using 100 mg catalyst. Interestingly, the photocatalytic efficiency was not affected upon multiple use of the photocatalyst. Moreover, negative activation energy was obtained which reveals super activity of the introduced photocatalyst. The distinct photocatalytic activity indicates the complete annihilation of the electrons–holes recombination process and abundant existence of electrons on the catalyst surfaces due to strong electrons capturing the operation of the utilized polar CdSO₄ nanoparticles. The introduced photocatalyst has been prepared using the sol–gel technique. Overall, the simplicity of the synthesizing procedure and the obtained featured photocatalytic activity strongly recommend the introduced nanoparticles to treat the methomyl-containing polluted water.     

Photocatalytic degradation of acetaminophen in modified TiO2 under visible irradiation

This study investigated the photocatalytic degradation of acetaminophen (ACT) in synthetic titanium dioxide (TiO₂) solution under a visible light (λ >440 nm). The TiO₂ photocatalyst used in this study was synthesized via sol–gel method and doped with potassium aluminum sulfate (KAl(SO₄)₂) and sodium aluminate (NaAlO₂). The influence of some parameters on the degradation of acetaminophen was examined, such as initial pH, photocatalyst dosage, and initial ACT concentration. The optimal operational conditions were also determined. Results showed that synthetic TiO₂ catalysts presented mainly as anatase phase and no rutile phase was observed. The results of photocatalytic degradation showed that LED alone degraded negligible amount of ACT but with the presence of TiO₂/KAl(SO₄)₂, 95 % removal of 0.10-mM acetaminophen in 540-min irradiation time was achieved. The synthetic TiO₂/KAl(SO₄)₂ presented better photocatalytic degradation of acetaminophen than commercially available Degussa P-25. The weak crystallinity of synthesized TiO₂/NaAlO₂ photocatalyst showed low photocatalytic degradation than TiO₂/KAl(SO₄)₂. The optimal operational conditions were obtained in pH 6.9 with a dose of 1.0 g/L TiO₂/KAl(SO₄)₂ at 30 °C. Kinetic study illustrated that photocatalytic degradation of acetaminophen fits well in the pseudo-first order model. Competitive reactions from intermediates affected the degradation rate of ACT, and were more obvious as the initial ACT concentration increased.     

TiO2膜降解水中污染物的稳定性考察与再生方法研究

针对实际水处理中对催化剂性能的要求，以光催化降解苯酚溶液作为探针反应，考察了玻璃纤维网上负载的TiO₂膜催化剂长期使用条件下的稳定性，研究了催化剂在自来水中使用失活后的再生方法。结果表明，经过50次使用之后，膜催化剂120 min反应对苯酚的降解率从100%下降至83%，总体上看，所制催化剂还是具有相当好的稳定性；在反应器中用蒸馏水浸泡配合光催化反应对TiO₂膜催化剂进行原位再生是一种可行的再生途径。     

氮掺杂二氧化钛可见光催化降解曙红Y溶液

采用溶胶凝胶法制备了氮掺杂二氧化钛光催化剂,用XRD、SEM、FTIR和粒度分析仪对催化剂进行了表征,并且在可见光作用下对曙红Y溶液进行了光催化降解实验。研究了催化剂的投加量、曙红Y的初始浓度、光照时间和pH对曙红Y溶液的光降解效果。结果表明,以可见光作光源,催化剂的投入量为0.4 g,曙红Y溶液的初始浓度为20 mg/L,光照时间为50 min,pH=4条件下,曙红Y溶液的降解率达98.87%。     

氧化亚铜光催化降解活性艳红的研究

制备了纳米SiO2-Cu2O复合氧化物,并对其进行表征。研究了SiO2-Cu2O在可见光照射下光催化降解活性艳红X-3B的性能。考察了催化剂组成、活性艳红浓度、催化剂用量、H2O2等对光催化反应的影响,还研究了Cu2O光催化反应动力学。结果表明,用SiO2摩尔含量为2%的SiO2-Cu2O光催化降解活性艳红,反应4 h,活性艳红降解率达到85%,降解反应为一级反应。     

Photocatalytic degradation of p,p′-DDT under UV and visible light using interstitial N-doped TiO2

1,1,1-trichloro-2,2-bis(p-chlorophenyl)ethane (or p,p′-DDT) is one of the most persistent pesticides. It is resistant to breakdown in nature and cause the water contamination problem. In this work, a major objective was to demonstrate the application of N-doped TiO₂ in degradation and mineralization of the p,p′-DDT under UV and visible light in aqueous solution. The N-doped TiO₂ nanopowders were prepared by a simple modified sol–gel procedure using diethanolamine (DEA) as a nitrogen source. The catalyst characteristics were investigated using XRD, SEM, TEM, and XPS. The adsorption and photocatalytic oxidation of p,p′-DDT using the synthesized N-doped TiO₂ under UV and visible light were conducted in a batch photocatalytic experiment. The kinetics and p,p′-DDT degradation performance of the N-doped TiO₂ were evaluated. Results show that the N-doped TiO₂ can degrade p,p′-DDT effectively under both UV and visible lights. The rate constant of the p,p′-DDT degradation under UV light was only 0.0121 min^?1, whereas the rate constant of the p,p′-DDT degradation under visible light was 0.1282 min^?1. Under visible light, the 100% degradation of p,p′-DDT were obtained from N-doped TiO₂ catalyst. The reaction rate of p,p′-DDT degradation using N-doped TiO₂ under visible light was sixfold higher than that under UV light. According to Langmuir-Hinshelwood model, the adsorption equilibrium constant (K) for the N-doped TiO₂ under visible light was 0.03078 L mg^?1, and the apparent reaction rate constant (k) was 1.3941 mg L^?1-min. Major intermediates detected during the p,p′-DDT degradation were p,p′-DDE, o,p′-DDE, p,p′-DDD and p,p′-DDD. Results from this work can be applied further for the breakdown of p,p′-DDT molecule in the real contaminated water using this technology.     

Photocatalytic discoloration of Methyl Orange by anatase/schorl composite: optimization using response surface method

The anatase/schorl composites were prepared and employed for the photocatalytic discoloration of an azo dye, Methyl Orange (MO). X-ray diffraction results indicated that TiO₂ existed in the form of anatase phase and no diffraction peaks of schorl could be observed for all the composite samples. Scanning electron micrographs showed that the particles of anatase were well deposited and dispersed on the surface of schorl. Photocatalytic experiments revealed that the anatase/schorl composites exhibited higher photocatalytic activity for MO discoloration than pure TiO₂ and more than 90 % discoloration ratio could be obtained within 60 min UV irradiation when the sample containing 3 wt.% of schorl as TiO₂ support was used. Then, the central composite design (CCD) under the response surface methodology (RSM) was employed for the experiment design and process optimization. The significance of a second-order polynomial model for predicting the optimal values of MO discoloration was evaluated by the analysis of variance (ANOVA) and 3D response surface plots for the interactions between two variables were constructed. Based on the model prediction, the optimum conditions for the photocatalytic discoloration of MO by TiO₂/schorl composite were determined to be 15?×?10^?3 mM MO initial concentration, 2.7 g/l photocatalyst dosage, solution pH 6.6 and 43 min reaction time, with a maximum MO discoloration ratio of 98.6 %. Finally, a discoloration ratio of 94.3 % was achieved for the real sample under the optimum conditions, which was very close to the predicted value, implying that RSM is a powerful and satisfactory strategy for the process optimization.     

Titania-supported silver-based bimetallic nanoparticles as photocatalysts

Photocatalytic process has shown recently a great potential as an environmental friendly and clean remediation technology for organic pollutants in wastewater. This work described the synthesis of silver-based bimetallic nanoparticles using colloid chemistry and the subsequent immobilization onto titania to form composite photocatalytic materials (titania-supported Ag–Pt nanoparticles). The photocatalysts were characterized by X-ray diffraction, electron microscopy, and nitrogen physisorption. The catalytic activity of the photocatalysts was evaluated by photocatalytic degradation of phenol and 2-chlorophenol (2-CP) in synthetic wastewater solutions. The photocatalytic processes were conducted in a batch photoreactor containing appropriate solutions of phenol and 2-CP with UV irradiation of 450 W. UV-visible spectrophotometer was used for analyzing the concentration of phenol and 2-CP in solutions. Parameters affecting the photocatalytic process such as the solution pH, phenol and 2-CP concentrations, and catalyst concentration were investigated. The results obtained revealed that TiO₂-supported Ag/Pt nanoparticles showed a higher activity for UV-photocatalytic degradation of both phenol and 2-CP pollutants in the solution (as compared to the plain rutile TiO₂). The photodegradation processes were optimized by the 0.5-g/L catalyst with a pollutant concentration of 50 mg/L for all the samples. Complete degradation for both phenol and 2-CP was achieved after 120 min.     

光电催化氧化法降解藻毒素MCLR

使用DSA阳极,对光电催化氧化降解藻毒素MCLR的效能及其影响因素进行了研究。结果表明,电极表面的TiO2在光催化氧化降解MCLR的过程中发挥了明显的光催化作用。在光降解、电催化氧化、光催化氧化和光电催化氧化4个过程中,光电催化氧化对MCLR和TOC的去除率最高,分别可达100%和13%,并且光电催化氧化的去除率大于光催化氧化和电催化氧化之和,表明后两者的耦合过程产生了一定的协同作用。辐照光源和电流密度存在最佳匹配条件,分别为UVC辐照、电流密度10 mA/cm2和UVA辐照、电流密度1.0 mA/cm2,此条件下光电协同作用最显著。在光电催化氧化过程中,随极板间距增大而出现的去除率下降取决于电催化过程,而不是光催化过程;光电催化氧化MCLR的去除率随其初始浓度增加而减小。     

Photocatalytic ozonation of terephthalic acid: a by-product-oriented decomposition study

Terephthalic acid (TA) is considered as a refractory model compound. For this reason, the TA degradation usually requires a prolonged reaction time to achieve mineralization. In this study, vanadium oxide (V_xO_y) supported on titanium oxide (TiO₂) served as a photocatalyst in the ozonation of the TA with light-emitting diodes (LEDs), having a bandwidth centered at 452 nm. The modified catalyst (V_xO_y/TiO₂) in combination with ozone and LEDs improved the TA degradation and its by-products. The results obtained by this system were compared with photolysis, single ozonation, catalytic ozonation, and photocatalytic ozonation of V_xO_y/TiO₂ with UV lamp. The LED-based photocatalytic ozonation showed almost the same decomposition efficiency of the TA, but it was better in comparison with the use of UV lamp. The oxalic acid accumulation, as the final product of the TA decomposition, was directly influenced by either the presence of V_xO_y or/and the LED irradiation. Several by-products formed during the TA degradation, such as muconic, fumaric, and oxalic acids, were identified. Besides, two unidentified by-products were completely removed during the observed time (60 min). It was proposed that the TA elimination in the presence of V_xO_y/TiO₂ as catalyst was carried out by the combination of different mechanisms: molecular ozone reaction, indirect mechanism conducted by ·OH, and the surface complex formation.     

微波辅助光催化降解高浓度活性黑

利用改装的家用微波炉、微波无极灯和TiO2催化剂研究了水中高浓度活性黑的光催化降解.系统考察了TiO2投加量、pH、微波无极灯数量对微波辅助光催化处理效果的影响,得出微波辅助光催化的最佳操作条件,并在最佳条件下对活性黑的脱色及矿化效果进行研究.结果表明,TiO2投加量存在最佳值2 g/L,降低pH和增加微波无极灯数量均可提高活性黑的降解率.在TiO2的投加量为2 g/L,pH =3,微波无极灯数量为3的最佳光催化条件下,400 mg/L的活性黑溶液反应180 min时可实现完全脱色,反应300 min时,TOC去除率高达89.1％.     

Photocatalytic Degradation of the Herbicide Erioglaucine in the Presence of Nanosized Titanium Dioxide: Comparison and Modeling of Reaction Kinetics

The present work mainly deals with photocatalytic degradation of a herbicide, erioglaucine, in water in the presence of TiO₂ nanoparticles (Degussa P-25) under ultraviolet (UV) light illumination (30 W). The degradation rate of erioglaucine was not so high when the photolysis was carried out in the absence of TiO₂ and it was negligible in the absence of UV light. We have studied the influence of the basic photocatalytic parameters such as pH of the solution, amount of TiO₂, irradiation time and initial concentration of erioglaucine on the photodegradation efficiency of erioglaucine. A kinetic model is applied for the photocatalytic oxidation by the UV/TiO₂ system. Experimental results indicated that the photocatalytic degradation process could be explained in terms of the Langmuir–Hinshelwood kinetic model. The values of the adsorption equilibrium constant, K, and the second order kinetic rate constant, k, were 0.116 ppm^{? 1} and 0.984 ppm min^{? 1}, respectively. In this work, we also compared the reactivity between the commercial TiO₂ Degussa P-25 and a rutile TiO₂. The photocatalytic activities of both photocatalysts were tested using the herbicide solution. We have noticed that photodegradation efficiency was different between both of them. The higher photoactivity of Degussa P-25 compared to that of rutile TiO₂ for the photodegradation of erioglaucine may be due to higher hydroxyl content, higher surface area, nano-size and crystallinity of the Degussa P-25. Our results also showed that the UV/TiO₂ process with Degussa P-25 as photocatalyst was appropriate as the effective treatment method for removal of erioglaucine from a real wastewater. The electrical energy consumption per order of magnitude for photocatalytic degradation of erioglaucine was lower with Degussa P-25 than in the presence of rutile TiO₂.