生物活性炭填料反应器处理含盐水体的硝化性能

以颗粒活性炭为填料,采用盐度梯度两步驯化法构建含盐水体生物滤器硝化功能,研究了生物滤器稳定后水力停留时间(hydraulic retention time,HRT)、进水氨氮负荷和CODMn/N等对反应器硝化性能的影响。结果表明,25～27℃,盐度30的含盐水体生物滤器硝化功能构建需73 d,其中淡水生物滤器硝化功能构建需28 d,淡水驯化为盐度15的生物滤器需19 d,盐度15驯化为盐度30的生物滤器需26 d;实验条件下生物活性炭填料反应器中生物量达到146～742.1 nmolP/g-BAC;调节进水氨氮浓度2 mg/L左右时,最佳HRT为1 h,氨氮去除率达到84.98%,相应的氨氧化菌和硝酸菌氧吸收速率(oxygen uptake rate,OUR)分别为2.091和1.948 mg O2/(g-BAC.h);HRT为1 h时,随着进水氨氮负荷的加大,氨氮去除率逐渐降低,当进水氨氮负荷由0.12增加到0.48 g-N/(kg-BAC.d)时,氨氮去除率由84.98%降低到41.68%,同时氨氧化菌OUR由2.091降低到0.625 mg O2/(g-BAC.h);随着CODMn/N的升高,氨氮去除率下降,CODMn/N从1～8时,氨氮去除率由84.98%降低到53.64%,CODMn去除率却逐渐增加,由40.86%增加到93.59%,异养菌OUR随着CODMn/N升高呈上升趋势,最大达到0.914 mg O2/(g-BAC.h)。     

Treatment of carbofuran-bearing synthetic wastewater using UASB process

In the present study, fate of carbofuran in anaerobic environments and the adverse effects of carbofuran on conventional anaerobic systems were evaluated. Carbofuran degradation studies were carried out in batch reactors with varying carbofuran concentrations of 0 to 270.73 mg/L corresponding to a sludge-loading rate (SLR) of 2.12 x 10(-6) to 3.83 x 10(-3) g of carbofuran/g of volatile suspended solids (VSS)/d. Carbofuran concentration was reduced to undetectable levels at the end of 8 and 13 days in the batch reactors operated with a SLR of 2.12 x 10(-6) and 3.33 x 10(-5) g of carbofuran/g of VSS/d, respectively. Performances of two anaerobic reactors i.e. upflow anaerobic sludge blanket (UASB) and modified UASB (with tube settlers) were evaluated in the presence and absence of carbofuran using synthetic wastewater. In the absence of carbofuran, the soluble chemical oxygen demand (COD) removal efficiency in the conventional UASB reactor at 8 h and 6 h hydraulic retention time (HRT) was nearly 88% and 76%, respectively, whereas in modified UASB reactor it was increased to 90% at 8 h HRT and 78% at 6 h HRT. When 28 mg/L (SLR of 1.19 x 10(-2) g of carbofuran/g of VSS/d) of carbofuran was introduced in the reactors, the COD removal efficiency was reduced to 41% and 44% in conventional and modified UASB reactors respectively. However, the reactor could maintain around 80% COD removal efficiency at a carbofuran concentration of 7.84 mg/L (SLR of 3.64 x 10(-3) g of carbofuran/g of VSS/d). The reactor efficiency was also measured in terms of specific acetoclastic methanogenic activity (SMA). The toxic effect of carbofuran was reversible to a certain extent. Carbofuran removal efficiency in the conventional UASB reactor at carbofuran concentrations of 7, 13 and 28 mg/L were 40 +/- 3%, 27 +/- 3%, and 11 +/- 3%, respectively. In modified UASB reactor, carbofuran removal efficiency was almost uniform at 7 and 13 mg/L but it was reduced nearly by 56% at 28 mg/L. The major metabolite of carbofuran i.e. 3-keto carbofuran was found in all the reactors.     

Anaerobic biodegradation of high strength 2-chlorophenol-containing synthetic wastewater in a fixed bed reactor

In this study the continuous treatment of 2-chlorophenol (2-CP) containing synthetic wastewater at increasing concentrations up to 2600 mg L-1 in an anaerobic fixed bed reactor was achieved. As a source of microorganisms municipal sewage sludge was acclimatised to maximally 50 mg L-1 2-CP by 3 successive feedings within 1.5 months. Then, an anaerobic fixed bed reactor was inoculated with this sludge and was operated for 318 d, during which the 2-CP influent concentration was stepwise increased from 50 to 2600 mg L-1 within 265 d. At a hydraulic retention time (HRT) of 2.2 d the 2-CP loading rate was 2 g L-1 d-1 and the average 2-CP removal rate was 0.87 g L-1 d-1, accounting for 73% removal. This is the highest 2-CP removal rate ever reported. The negative effect of a 2-CP loading rate of 1.36 g L-1 d-1 on 2-CP removal was reversible within 2 wk when lower loading conditions (e.g. 0.76 g 2-CP L-1 d-1) were re-established. The median chloride ion release per unit 2-CP degraded was 0.24, which was reasonably close to the theoretically expected value of 0.28. In a batch assay, carried out with relatively clear reactor effluent, the highest removal rate of 2-CP was 175 mg L-1 d-1. At the time of reactor termination on day 318, the 2-CP removal rate by the biofilm in the reactor was 0.61 g L-1 d-1, corresponding to a HRT of 3.4 d and a 2-CP loading rate of 0.76 g L-1 d-1. At these very stable conditions removal of COD was 84% and of 2-CP 81%     

Influence of the organic loading rate on the performance and the granular sludge characteristics of an EGSB reactor used for treating traditional Chinese medicine wastewater

The effects of the organic loading rate (OLR) on the performance and the granular sludge characteristics of an expanded granular sludge bed (EGSB) reactor used for treating real traditional Chinese medicine (TCM) wastewater were investigated. Over 90 % of the COD removal by the EGSB reactor was observed at the OLRs of 4 to 13 kg COD/(m³ day). However, increasing the OLR to 20 kg COD/(m³ day) by reducing the hydraulic retention time (HRT 6 h) reduced the COD removal efficiency to 78 %. The volatile fatty acid (VFA) concentration was 512.22 mg/L, resulting in an accumulation of VFAs, and propionic acid was the main acidification product, accounting for 66.51 % of the total VFAs. When the OLR increased from 10 to 20 kg COD/(m³ day), the average size of the granule sludge decreased from 469 to 258 μm. There was an obvious reduction in the concentration of Ca²⁺ and Mg²⁺ in the granular sludge. The visible humic acid-like peak was identified in the three-dimensional excitation-emission matrix (EEM) fluorescence spectra of the soluble microbial products (SMPs). The fatty acid bond, amide II bond, amide III bond, and C–H bond bending were also observed in the Fourier transform infrared (FTIR) spectra of the SMPs. Methanobacterium formicicum, Methanococcus, and Bacteria populations exhibited significant shifts, and these changes were accompanied by an increase in VFA production. The results indicated that a short HRT and high OLR in the EGSB reactor caused the accumulation of polysaccharides, protein, and VFAs, thereby inhibiting the activity of methanogenic bacteria and causing granular sludge corruption.     

高氯离子味精尾母液废水厌氧处理研究

味精尾母液废水COD浓度极高同时含有大最氯离子.采用UASB反应器对味精尾母液废水进行处理,其中接种污泥来自啤酒厂UASB反应器.实验表明:当氯离子浓度在4 500 mg/L以下时,对厌氧微生物没有明礁的抑制作用;5 000 mg/L的氯离子浓度可以看作一个抑制限值,但经过驯化后,仍可获得较好的COD去除效果;当氯离子浓度达到8 000mg/L左右时,COD平均去除率在80%以上.     

管式反应器处理生活污水的效能

研发了一种基于射流曝气的管式反应设备,考察了负荷和DO对反应器处理效能的影响。实验结果表明,在温度为15℃、DO 6.0 mg/L、有机负荷为1.0 kg COD/(m3.d)、氮负荷为0.30 kg TN/(m3.d)、HRT为8 h的条件下,管式反应器可使生活污水的COD、NH4+-N及TN分别从335 mg/L、105 mg/L及110 mg/L降至43 mg/L、14 mg/L及18 mg/L,去除率分别为87%、86%和83%。DO对反应器脱氮效能影响显著,DO为6 mg/L时,能构建出同步硝化反硝化系统,NH4+-N和TN的去除率分别为96.6%和86.7%。     

悬浮填料生物膜床反应器处理高校生活污水

本研究利用悬浮填料生物膜床反应器处理高校生活污水 ,对CODCr、氨氮和总磷有较好的去除效果。水力停留时间 6h时 ,CODCr总去除率最高可达到 95 % ,出水CODCr稳定在 30mg/L以下 ;总磷去除率达到 5 0 %以上 ,出水总磷含量低于 0 5mg/L ;对NH3 N的去除率可以稳定在 80 %以上 ,出水NH3 N低于 1mg/L。     

纳米生态基对水产养殖污水的处理效果

采用三因子四水平的正交设计,实验研究了纳米生态基在不同温度、溶解氧和水力停留时间下对水产养殖污水的处理效果,确定了纳米生态基处理养殖污水的最佳条件。结果表明,含氨氮和亚硝氮浓度较高的模拟养殖污水用纳米生态基挂膜,所需时间约为22 d。纳米生态基对氨氮的去除效果明显,平均去除率达到93.5%。对氨氮去除率的影响程度,水力停留时间>温度>溶解氧。当温度为30℃,DO为5.43 mg/L,HRT为0.33 h时,纳米生态基对氨氮的处理能力最佳,去除率达到94.6%。纳米生态基对亚硝氮的平均去除率为69.3%。对亚硝氮去除率的影响程度,水力停留时间>溶解氧>温度。当温度为21℃,DO为6.40 mg/L,HRT为0.33 h时,纳米生态基对亚硝氮的处理能力最佳,去除率为71.5%。纳米生态基处理养殖污水的最佳条件:温度为30℃,DO为6.40 mg/L,HRT为0.33 h。     

Coupling digestion in a pilot-scale UASB reactor and electrochemical oxidation over BDD anode to treat diluted cheese whey

The efficiency of the anaerobic treatment of cheese whey (CW) at mesophilic conditions was investigated. In addition, the applicability of electrochemical oxidation as an advanced post-treatment for the complete removal of chemical oxygen demand (COD) from the anaerobically treated cheese whey was evaluated. The diluted cheese whey, having a pH of 6.5 and a total COD of 6 g/L, was first treated in a 600-L, pilot-scale up-flow anaerobic sludge blanket (UASB) reactor. The UASB process, which was operated for 87 days at mesophilic conditions (32?±?2 °C) at a hydraulic retention time (HRT) of 3 days, led to a COD removal efficiency between 66 and 97 %, while the particulate matter of the wastewater was effectively removed by entrapment in the sludge blanket of the reactor. When the anaerobic reactor effluent was post-treated over a boron-doped diamond (BDD) anode at 9 and 18 A and in the presence of NaCl as the supporting electrolyte, complete removal of COD was attained after 3–4 h of reaction. During electrochemical experiments, three groups of organochlorinated compounds, namely trihalomethanes (THMs), haloacetonitriles (HANs), and haloketons (HKs), as well as 1,2-dichloroethane (DCA) and chloropicrin were identified as by-products of the process; these, alongside free chlorine, are thought to increase the matrix ecotoxicity to Artemia salina.     

Effect of inorganic and organic solutes on zero-valent aluminum-activated hydrogen peroxide and persulfate oxidation of bisphenol A

The effect of varying inorganic (chloride, nitrate, sulfate, and phosphate) and organic (represented by humic acid) solutes on the removal of aqueous micropollutant bisphenol A (BPA; 8.8 μM; 2 mg/L) with the oxidizing agents hydrogen peroxide (HP; 0.25 mM) and persulfate (PS; 0.25 mM) activated using zero-valent aluminum (ZVA) nanoparticles (1 g/L) was investigated at a pH of 3. In the absence of the solutes, the PS/ZVA treatment system was superior to the HP/ZVA system in terms of BPA removal rates and kinetics. Further, the HP/ZVA process was not affected by nitrate (50 mg/L) addition, whereas chloride (250 mg/L) exhibited no effect on the PS/ZVA process. The negative effect of inorganic anions on BPA removal generally speaking increased with increasing charge in the following order: NO₃^? (no inhibition)?<?Cl^? (250 mg/L)?=?SO₄^2??<?PO₄^3? for HP/ZVA and Cl^? (250 mg/L; no inhibition)?<?NO₃^??<?SO₄^2??<?PO₄^3? for PS/ZVA. Upon addition of 20 mg/L humic acid representing natural organic matter, BPA removals decreased from 72 and 100% in the absence of solutes to 24 and 57% for HP/ZVA and PS/ZVA treatments, respectively. The solute mixture containing all inorganic and organic solutes together partly suppressed the inhibitory effects of phosphate and humic acid on BPA removals decreasing to 46 and 43% after HP/ZVA and PS/ZVA treatments, respectively. Dissolved organic carbon removals were obtained in the range of 30 and 47% (the HP/ZVA process), as well as 47 and 57% (the PS/ZVA process) for the experiments in the presence of 20 mg/L humic acid and solute mixture, respectively. The relative Vibrio fischeri photoluminescence inhibition decreased particularly for the PS/ZVA treatment system, which exhibited a higher treatment performance than the HP/ZVA treatment system.     

A/O+MBR工艺处理玉米深加工废水的中试研究

实验基于企业污水站的改造工程,研究了MBR对玉米深加工废水的处理效果并对工艺运行参数优化提出建议.结果表明,该工艺对COD的去除率可以达到90％以上,出水稳定在26 mg/L左右;出水NH4-N达到1 mg/L以下;TN去除率达到70％以上,出水TN达到10 mg/L以下,出水完全达到排放标准.通过4种工况的比较,说明在污泥浓度8 g/L左右,曝气池内DO在3 mg/L左右,MBR内DO＞4 mg/L,好氧段停留时间13.5 h,并保证3h以上的缺氧段水力停留段时间的条件下,A/O+ MBR工艺可以有效去除玉米深加工废水中的污染物.     

焦化废水中COD、挥发酚和硫氰化物同步高效去除

采用两级膨胀颗粒污泥床(EGSB)反应器在微氧条件下处理焦化废水,考察了该工艺对焦化废水中挥发酚、硫氰化物、氰化物和COD的去除效果。研究结果表明,在进水流量为1 L/h,总水力停留时间(HRT)为24 h的条件下,两级EGSB反应器对COD的去除效果较好。稳定运行时,在进水挥发酚为56.8~185.1 mg/L、硫氰化物为287.1~539.9 mg/L、氰化物为0.17~0.72 mg/L的条件下,系统对其平均去除率分别为99.9%、96.8%和82.6%,出水挥发酚和氰化物均能达到《污水综合排放标准(GB8978-1996)》的一级标准。进水COD浓度在1 084~1 880 mg/L之间,平均去除率为76.9%,出水平均浓度为325 mg/L。     

好氧颗粒污泥自生动态膜生物反应器处理碱减量印染废水

自生动态膜生物反应器(SFDMBR)接种颗粒污泥启动,研究溶解氧浓度和水力停留时间对该反应器处理碱减量印染废水的影响。自生动态膜生物反应器形成稳定的动态膜后,出水浊度小于10 NTU,系统对浊度的去除率在90%以上,溶解氧和水力停留时间对反应器出水浊度基本无影响。系统对废水色度的去除率随着溶解氧浓度的提高和水力停留时间的延长而增加,但是系统对色度的去除效率一般不超过40%。溶解氧浓度由0.3 mg/L逐渐增大至2.4 mg/L,COD的去除率由40%提升至80%,而当溶解氧浓度大于1.0 mg/L后,UV254的去除率达到95%。水力停留时间在8~48 h时,COD去除效率由65%逐渐上升至85%左右;水力停留时间在8~32 h,UV254去除效率为68%~93%,超过32 h后水力停留时间对UV254去除效率的影响已不明显。     

COD对生物除磷颗粒污泥稳定性影响研究

颗粒污泥稳定性是影响其应用的主要因素之一.以SBR中成熟的生物除磷颗粒污泥为研究对象,探讨进水COD浓度对系统稳定性的影响.结果表明,当进水COD浓度由300 mg/L逐渐升高到500 mg/L时,磷去除率由93%降低到88%;当进水COD浓度在400 mg/L以下时,污泥的最大比释磷速率和比吸磷速率分别为45.2 m...     

AFB-SBR工艺处理蓝皮制革工业废水

采用厌氧流化床(AFB)-序批式反应器(SBR)工艺处理蓝皮制革工业废水。分别考察了水力停留时间(HRT)、容积负荷对厌氧流化床以及曝气时间、污泥浓度、溶解氧浓度对SBR反应器处理效果的影响。试验结果表明,AFB将实验废水的BOD_5/COD(B/C)值由0.19～0.26提高至0.35～0.42,有效提高了其可生化性;在进水COD浓度为1 700～1 890 mg/L、HRT为1 d、容积负荷为1.792 kg COD/(m~3·d)时,COD去除率达65.2%～68.5%,且具有良好的抗冲击负荷能力。SBR在进水COD浓度为628～712 mg/L、污泥浓度为2.9 g/L、曝气时间为10 h、溶解氧浓度为2 mg/L工况下,COD去除率达87.6%,NH_3-N去除率达93.6%,处理后出水水质符合污水综合排放标准(GB 8978-1996)中的一级标准要求。     

一体化A/O工艺碳氮比对脱氮除碳的影响

依据好氧硝化和缺氧反硝化生物脱氮除碳工艺原理，设计了一体化生物膜法A/O反应器，并将其应用于生活污水处理，取得了理想的处理效果。实验结果表明，水力停留时间HRT＝12 h，COD进水浓度处于150～500 mg/L范围内，COD的去除率均在90%以上，且出水均在40 mg/L以下；当C/N比为8.5以下时，NH₃-N去除率高于90%，其出水浓度小于5 mg/L；当C/N比为7.5左右时，具有较高的总氮脱除效果，TN去除率可达到70%。     

UASB启动及不同HRT对老龄垃圾渗滤液处理效果的影响

在UASB反应器中接种好氧污泥培养厌氧颗粒污泥进行启动,研究不同HRT对老龄(13年)垃圾渗滤液对处理效果的影响情况。通过保持进水COD浓度不变、逐步缩短HRT从而提高容积负荷到40 g COD/(L.d)的方法,可以培育出直径为1～3 mm颗粒污泥,最终产气量稳定在100 L/d,甲烷含量在60%～70%之间,COD去除率保持在90%左右,污泥层最底部MLSS为81 g/L。逐步提高HRT依次为6、12、24、48和72 h考察其对处理效果的影响,当HRT为24 h时处理效果最好,COD去除率最高达到35%左右。     

Electrochemical mineralization and detoxification of naphthenic acids on boron-doped diamond anodes

Electrochemical oxidation (ELOX) with boron-doped diamond (BDD) anodes was successfully applied to degrade a model aqueous solution of a mixture of commercial naphthenic acids (NAs). The model mixture was prepared resembling the NA and salt composition of oil sands process-affected water (OSPW) as described in the literature. The initial concentration of NAs between 70 and 120 mg/L did not influence the electrooxidation kinetics. However, increasing the applied current density from 20 to 100 A/m² and the initial chloride concentration from 15 to 70 and 150 mg/L accelerated the rate of NA degradation. At higher chloride concentration, the formation of indirect oxidative species could contribute to the faster oxidation of NAs. Complete chemical oxygen demand removal at an initial NA concentration of 120 mg/L, 70 mg/L of chloride and applied 50 A/m² of current density was achieved, and 85% mineralization, defined as the decrease of the total organic carbon (TOC) content, was attained. Moreover, after 6 h of treatment and independently on the experimental conditions, the formation of more toxic species, i.e. perchlorate and organochlorinated compounds, was not detected. Finally, the use of ELOX with BDD anodes produced a 7 to 11-fold reduction of toxicity (IC₅₀ towards Vibrio fischeri) after 2 h of treatment.     

内循环（IC）厌氧反应器处理糖蜜酒精废水的研究

糖蜜酒精废水由于含有高浓度的COD和硫酸盐,一般厌氧反应器无法有效处理.研究了IC反应器处理糖蜜酒精废水的效果.考察其COD及硫酸盐的去除率、沼气的产量和组分等.结果表明,反应器对于COD为5000～10 000 mg/L的中、高浓度废水去除效果良好,当COD在20 000～30 000 mg/L时,在适应了1～2个停留时间后,去除效果达到稳定,去除率在90%左右.实验中最高容积负荷提升至40 kg COD/m3·d左右.本研究中所用的糖蜜酒精废水的COD/SO24-的平均值为61.9,未对反应器的处理效果及产气量产生影响.     

Coagulant recovery from water treatment plant sludge and reuse in post-treatment of UASB reactor effluent treating municipal wastewater

In the present study, feasibility of recovering the coagulant from water treatment plant sludge with sulphuric acid and reusing it in post-treatment of upflow anaerobic sludge blanket (UASB) reactor effluent treating municipal wastewater were studied. The optimum conditions for coagulant recovery from water treatment plant sludge were investigated using response surface methodology (RSM). Sludge obtained from plants that use polyaluminium chloride (PACl) and alum coagulant was utilised for the study. Effect of three variables, pH, solid content and mixing time was studied using a Box–Behnken statistical experimental design. RSM model was developed based on the experimental aluminium recovery, and the response plots were developed. Results of the study showed significant effects of all the three variables and their interactions in the recovery process. The optimum aluminium recovery of 73.26 and 62.73 % from PACl sludge and alum sludge, respectively, was obtained at pH of 2.0, solid content of 0.5 % and mixing time of 30 min. The recovered coagulant solution had elevated concentrations of certain metals and chemical oxygen demand (COD) which raised concern about its reuse potential in water treatment. Hence, the coagulant recovered from PACl sludge was reused as coagulant for post-treatment of UASB reactor effluent treating municipal wastewater. The recovered coagulant gave 71 % COD, 80 % turbidity, 89 % phosphate, 77 % suspended solids and 99.5 % total coliform removal at 25 mg Al/L. Fresh PACl also gave similar performance but at higher dose of 40 mg Al/L. The results suggest that coagulant can be recovered from water treatment plant sludge and can be used to treat UASB reactor effluent treating municipal wastewater which can reduce the consumption of fresh coagulant in wastewater treatment.