溴化十六烷基吡啶改性沸石对水中甲基橙的吸附

采用溴化十六烷基吡啶(CPB)对天然沸石进行改性制备得到了CPB改性沸石,通过批量吸附实验考察了CPB改性沸石对水中阴离子染料甲基橙的去除作用。结果表明,天然沸石对水中甲基橙的吸附能力很差,而CPB改性沸石则可以有效吸附去除水中的甲基橙。CPB改性沸石对水中甲基橙的吸附能力随CPB负载量的增加而增加,CPB负载量最大的改性沸石对水中甲基橙的吸附能力最强。双分子层CPB改性沸石对水中甲基橙的去除率随吸附剂投加量的增加而增加,而CPB改性沸石对水中甲基橙的单位吸附量则随吸附剂投加量的增加而降低。双分子层CPB改性沸石对水中甲基橙的吸附平衡数据可以采用Langmuir等温吸附模型加以描述。根据Langmuir模型计算得到的CPB负载量为341 mmol/(kg沸石)的双分子层CPB改性沸石对水中甲基橙的最大吸附容量为63.7 mg/g(303 K和pH 7)。准二级动力学模型适合用于描述双分子层CPB改性沸石对水中甲基橙的吸附动力学过程。pH和反应温度对双分子层CPB改性沸石吸附水中甲基橙的影响较小。以上结果说明,双分子层CPB改性沸石适合作为一种吸附剂用于去除废水中的甲基橙。     

Dynamic behaviour of Cd2+ adsorption in equilibrium batch studies by CaCO3 −-rich Corbicula fluminea shell

This work presents the structural and adsorption properties of the CaCO₃ ^?-rich Corbicula fluminea shell as a natural and economic adsorbent to remove Cd ions from aqueous solutions under batch studies. Experiments were conducted with different contact times, various initial concentrations, initial solution pH and serial biosorbent dosage to examine the dynamic characterization of the adsorption and its influence on Cd uptake capacity. The characterization of the C. fluminea shell using SEM/EDX revealed that the adsorbent surface is mostly impregnated by small particles of potentially calcium salts. The dominant Cd adsorption mechanism is strongly pH and concentration dependent. A maximum Cd removal efficiency of 96.20 % was obtained at pH 7 while the optimum adsorbent dosage was observed as 5 g/L. The Langmuir isotherm was discovered to be more suitable to represent the experimental equilibrium isotherm results with higher correlation coefficients (R ²?>?0.98) than Freundlich (R ²?<?0.97).The correlation coefficient values (p?<?0.01) indicated the superiority of the Langmuir isotherm over the Freundlich isotherm.     

Removal of bisphenol A and some heavy metal ions by polydivinylbenzene magnetic latex particles

In this study, magnetic polydivinylbenzene latex particles MP_DVB with a core-shell structure were tested for the removal of bisphenol A (BPA), copper Cu(II), lead Pb(II), and zinc Zn(II) from aqueous solutions by a batch-adsorption technique. The effect of different parameters, such as initial concentration of pollutant, contact time, adsorbent dose, and initial pH solution on the adsorption of the different adsorbates considered was investigated. The adsorption of BPA, Cu(II), Pb(II), and Zn(II) was found to be fast, and the equilibrium was achieved within 30 min. The pH 5–5.5 was found to be the most suitable pH for metal removal. The presence of electrolytes and their increasing concentration reduced the metal adsorption capacity of the adsorbent. Whereas, the optimal pH for BPA adsorption was found 7, both hydrogen bonds and π–π interaction were thought responsible for the adsorption of BPA on MP_DVB. The adsorption kinetics of BPA, Cu(II), Pb(II), and Zn(II) were found to follow a pseudo-second-order kinetic model. Equilibrium data for BPA, Cu(II), Pb(II), and Zn(II) adsorption were fitted well by the Langmuir isotherm model. Furthermore, the desorption and regeneration studies have proven that MP_DVB can be employed repeatedly without impacting its adsorption capacity.     

改性松针对水体中铅(II)的吸附

探讨了改性松针(GXLsp)作为吸附剂对水体中铅离子的吸附性能,考察了吸附时间、溶液pH值、吸附剂用量、盐离子浓度、Pb(II)初始浓度及温度对改性松针吸附Pb(II)的影响。利用Langmuir和Freundlich等温线模型对实验数据进行非线性拟合分析,结果表明,Freundlich等温线模型能很好地描述松针对Pb(II)的吸附过程。热力学参数表明吸附是一个自发的吸热过程。改性松针对铅的吸附行为符合拟二级动力学方程,表明吸附过程是以化学吸附为主。在293K时松针对Pb(II)的饱和吸附量为318.3 mg/g,因此,GXLsp可作为一种高效低值生物质吸附剂以去除水体中重金属Pb(II)的污染。     

Adsorption of Co(II) by a carboxylate-functionalized polyacrylamide grafted lignocellulosics

A new adsorbent (PGBS-COOH) having carboxylate functional group at the chain end was synthesized by graft copolymerization of acrylamide onto banana stalk, BS (Musa Paradisiaca) using ferrous ammonium sulphate/H2O2 redox initiator system. The efficiency of the adsorbent in the removal of cobalt [Co(II)] from water was investigated using batch adsorption technique. The adsorbent exhibits very high adsorption potential for Co(II) and under optimum conditions more than 99% removal was achieved. The maximum adsorption capacity was observed at the pH range 6.5-9.0. The equilibrium isotherm data were analysed using three isotherm models, Langmuir, Freundlich and Scatchard, to determine the best fit equation for the sorption of Co(II) on the PGBS-COOH. A comparative study with a commercial cation exchanger, Ceralite IRC-50, having carboxylate functional group showed that PGBS-COOH is 2.8 times more effective compared to Ceralite IRC-50 at 30 degrees C. Synthetic nuclear power plant coolant water samples were also treated by the adsorbent to demonstrate its efficiency in removing Co(II) from water in the presence of other metal ions. Acid regeneration was tried for several cycles to recover the adsorbed metal ions and also to restore the sorbent to its original state.     

Application of zeolite-activated carbon macrocomposite for the adsorption of Acid Orange 7: isotherm, kinetic and thermodynamic studies

In this study, the adsorption behavior of azo dye Acid Orange 7 (AO7) from aqueous solution onto macrocomposite (MC) was investigated under various experimental conditions. The adsorbent, MC, which consists of a mixture of zeolite and activated carbon, was found to be effective in removing AO7. The MC were characterized by scanning electron microscopy (SEM), energy dispersive X-ray, point of zero charge, and Brunauer–Emmett–Teller surface area analysis. A series of experiments were performed via batch adsorption technique to examine the effect of the process variables, namely, contact time, initial dye concentration, and solution pH. The dye equilibrium adsorption was investigated, and the equilibrium data were fitted to Langmuir, Freundlich, and Tempkin isotherm models. The Langmuir isotherm model fits the equilibrium data better than the Freundlich isotherm model. For the kinetic study, pseudo-first-order, pseudo-second-order, and intraparticle diffusion model were used to fit the experimental data. The adsorption kinetic was found to be well described by the pseudo-second-order model. Thermodynamic analysis indicated that the adsorption process is a spontaneous and endothermic process. The SEM, Fourier transform infrared spectroscopy, ultraviolet–visible spectral and high performance liquid chromatography analysis were carried out before and after the adsorption process. For the phytotoxicity test, treated AO7 was found to be less toxic. Thus, the study indicated that MC has good potential use as an adsorbent for the removal of azo dye from aqueous solution.     

The removal of uranium (VI) from aqueous solutions onto activated carbon developed from grinded used tire

In this study, activated carbon was prepared from waste tire by KOH chemical activation. The pore properties including the BET surface area, pore volume, pore size distribution, and average pore diameter were characterized. BET surface area of the activated carbon was determined as 558 m²/g. The adsorption of uranium ions from the aqueous solution using this activated carbon has been investigated. Various physico-chemical parameters such as pH, initial metal ion concentration, and adsorbent dosage level and equilibrium contact time were studied by a batch method. The optimum pH for adsorption was found to be 3. The removal efficiency has also been determined for the adsorption system as a function of initial concentration. The experimental results were fitted to Langmuir, Freundlich, and Dubinin–Radushkevich (D-R) isotherm models. A comparison of best-fitting was performed using the coefficient of correlation and the Langmuir isotherm was found to well represent the measured sorption data. According to the evaluation using the Langmuir equation, the saturated monolayer sorption capacity of uranium ions onto waste tire activated carbon was 158.73 mg/g. The thermodynamic equilibrium constant and the Gibbs free energy were determined and results indicated the spontaneous nature of the adsorption process. Kinetics data were best described by pseudo-second-order model.     

Microwave-assisted synthesis of hydroxyapatite for the removal of lead(II) from aqueous solutions

Purpose

This study has the objective to evaluate the lead(II) removal capacity of hydroxyapatite powder synthesized by microwave as an alternative method to decrease production time and cost.

Methods

Hydroxyapatite (HA) was synthesized by a microwave-assisted precipitation method using calcium nitrate and ammonium hydrogen phosphate as calcium and phosphorus sources, respectively. X-ray diffraction and Fourier transform infrared results clearly revealed that the resulting powder was HA with high purity and crystallinity. The obtained powder was used for the removal of lead(II) from aqueous solutions. The effects of pH, amount of adsorbent, initial lead(II) concentration, and contact time were studied in batch experiments.

Results

In the adsorption experiments, maximum lead(II) retention was obtained at pH 6. Adsorption equilibrium was established after 40 min. It was found that the adsorption of lead(II) on HA was correlated well (R ²?=?0.958) with the Freundlich equation for the concentration range studied. Both ion exchange and adsorption process were thought to exist in the removal process.

Conclusions

This study indicates that easily and rapidly synthesized HA by microwave-assisted precipitation method could be used as an efficient adsorbent for removal of lead(II) from aqueous solutions.     

Phenol removal from wastewater by adsorption on zeolitic composite

It is well known that adsorption is an efficient method of removal of various pollutants from wastewater. The present study examines the phenol removal from water by adsorption on a new material, based on zeolitic volcanic tuff. This compound contains zeolitic tuff and cellulose, another known adsorbent, in a mass ratio of 4 to 1. The performances of the new adsorbent composite were compared with those of a widely used adsorbent material, zeolitic volcanic tuff. The adsorbent properties were tested on batch synthetic solutions containing 1–10 mg L^?1 (1–10 ppm) phenol, at room temperature without pH adjustment. The influence of the adsorbent dose, pH and contact time on the removal degree of phenol from water was investigated. The experimental data were modeled using the Langmuir, Freundlich, and Temkin adsorption isotherms. The Langmuir model was found to best represent our data revealing a monolayer adsorption with a maximum adsorption capacity between 0.12 and 0.53 mg g^?1 at 25 °C, for 2.00 g of adsorbent, depending on the initial phenol concentration. The adsorption kinetic study was performed using a pseudo-first- and pseudo-second-order kinetic models illustrating that phenol adsorption on zeolite composite is well described by pseudo-first kinetic equations. Our results indicated that phenol adsorption on the new adsorbent composite is superior to that on the classic zeolite.     

凹凸棒土对腐殖酸的低温吸附性能研究

首次研究凹凸棒土对饮用水中腐殖酸的低温吸附性能,考察5℃条件下,吸附时间与腐殖酸初始浓度、吸附剂投加量、pH对凹凸棒土吸附腐殖酸的影响,确定吸附剂的吸附等温线、吸附动力学和热力学等相关理论参数,研究凹凸棒土对腐殖酸的吸附性能与机理。结果表明,江苏盱眙凹凸棒土在温度5℃、pH=4、水中腐殖酸初始浓度为5 mg/L,投加量为15 g/L的条件下,吸附180 min后对腐殖酸的去除率可达97.26%。凹凸棒土对腐殖酸的吸附符合二级吸附动力学方程与Freundlich吸附等温式,吸附过程由孔隙内扩散过程控制,吸附为自发的吸热过程,包括物理吸附与化学吸附。根据Fre-undlich吸附等温式拟合计算,5℃、pH=7时理论最大吸附量为9 mg/g,说明凹凸棒土对于低温饮用水中腐殖酸具有良好的吸附效果。     

Adsorption of phosphate from aqueous solution onto alunite

The phosphate removal potential of alunite, a low cost and abundantly available material, has been investigated. The effects of calcination temperature and time of alunite, adsorbent particle size, pH and initial phosphate concentration on the phosphate adsorption by the calcined alunite have been studied. Phosphate removal was seen to increase with increasing calcination temperature, decreasing adsorbent particle size and pH. Adsorption of phosphate followed first-order rate kinetics. Langmuir and Freundlich adsorption isotherm constants and correlation coefficients were calculated and compared. It was concluded that the adsorption data of phosphate onto calcined alunite fitted to the Langmuir model more than Freundlich model. Specific surface areas of the calcined alunite were calculated at different calcination temperatures and particle sizes.     

Use of carbonised beet pulp carbon for removal of Remazol Turquoise Blue-G 133 from aqueous solution

Carbonised beet pulp (BPC) produced from agricultural solid waste by-product in sugar industry was used as adsorbent for the removal of Remazol Turquoise Blue-G 133 (RTB-G 133) dye in this study. The kinetics and equilibrium of sorption process were investigated with respect to pH, temperature and initial dye concentration. Adsorption studies with real textile wastewater were also performed. The results showed that adsorption was a strongly pH-dependent process, and optimum pH was determined as 1.0. The maximum dye adsorption capacity was obtained as 47.0 mg g^?1at the temperature of 25 °C at this pH value. The Freundlich and Langmuir adsorption models were used for describing the adsorption equilibrium data of the dye, and isotherm constants were evaluated depending on sorption temperature. Equilibrium data of RTB-G 133 sorption fitted very well to the Freundlich isotherm. Mass transfer and kinetic models were applied to the experimental data to examine the mechanisms of adsorption and potential rate-controlling steps. It was found that both external mass transfer and intra-particle diffusion played an important role in the adsorption mechanisms of dye and adsorption kinetics followed the pseudo second-order type kinetic model. The thermodynamic analysis indicated that the sorption process was exothermic and spontaneous in nature.     

Phosphate removal from wastewater using aluminium oxide as adsorbent

The development and manufacture of an adsorbent to remove phosphate for the prevention of eutrophication in lakes is very important. The use of aluminium oxide (alumina) as an organic adsorbent to remove phosphate from wastewater has been investigated. The characteristics of this absorption process were investigated to determine the important parameters, such as the pH and the aluminium ion concentration. Moreover, chemical treatment methods to enhance the adsorption capacity of alumina were tested. Dynamic studies and equilibrium adsorption isotherm studies were conducted to determine the adsorption capacity and efficiency. The experimental results indicate that it is necessary to increase the temperature above 500°C in order to obtain a high-capacity adsorbent, and alumina treated with acid or calcium or magnesium has a larger adsorption capacity for phosphate than untreated adsorbent. Moreover, the adsorption of phosphate was enhanced at a lower pH and a higher aluminium ion concentration, and a simple Freundlich isotherm could express the equilibrium adsorption isotherm, and the intragranular diffusion controlling model was used to test the dynamic studies. These findings have important implications for the application and development of aluminium oxide as a prospective adsorbent.     

Experimental study and modelling of zinc adsorption by granular activated carbon and natural zeolite

The metal removal capability of Granular Activated Carbon (GAC) and natural zeolite is evaluated in this study using zinc as a model adsorbate. The equilibrium and kinetic characteristics of zinc adsorption on GAC and natural zeolite were studied in batch stirred tank experiments. The adsorption data for both systems were fitted by Langmuir, Freundlich, Langmuir-Freundlich, and Redlich-Peterson models. The parameters in the adsorption isotherms were estimated from the experimental equilibrium data using MATLAB. Using these data the best isotherm can be selected. The effect of initial concentration on the transient behaviour of zinc removal by GAC and natural zeolite was investigated. In this work two surface reaction models, namely a second order reversible reaction model and a second order irreversible reaction model for describing Zn(II) removal by GAC and natural zeolite, were employed. Modelling studies using two different second order surface reaction models demonstrated that it is very difficult to come to a general conclusion about which model has better ability.     

Kinetic, equilibrium isotherm and thermodynamic studies of Cr(VI) adsorption onto low-cost adsorbent developed from peanut shell activated with phosphoric acid

A particular agricultural waste, peanut shell, has been used as precursor for activated carbon production by chemical activation with H₃PO₄. Unoxidized activated carbon was prepared in nitrogen atmosphere which was then heated in air at a desired temperature to get oxidized activated carbon. The prepared carbons were characterized for surface area, surface morphology, and pore volume and utilized for the removal of Cr(VI) from aqueous solution. Batch mode experiments were conducted to study the effects of pH, contact time, particle size, adsorbent dose, initial concentration of adsorbate, and temperature on the adsorption of Cr(VI). Cr(VI) adsorption was significantly dependent on solution pH, and the optimum adsorption was observed at pH 2. Pseudo-first-order, pseudo-second-order, and intraparticle diffusion models were used to analyze the kinetic data obtained at different initial Cr(VI) concentrations. The adsorption kinetic data were described very well by the pseudo-second-order model. Equilibrium isotherm data were analyzed by the Langmuir, Freundlich, and Temkin models. The results showed that the Langmuir adsorption isotherm model fitted the data better in the temperature range studied. The adsorption capacity which was found to increase with temperature showed the endothermic nature of Cr(VI) adsorption. The thermodynamic parameters, such as Gibb’s Free energy change (ΔG°), standard enthalpy change (ΔH°), and standard entropy change (ΔS°) were evaluated.     

天然及CaCl2改性沸石对四环素的吸附

通过静态吸附实验研究了水中四环素在天然和CaCl2改性沸石上的吸附行为及机制。实验表明,天然沸石对四环素具有吸附能力,CaCl2改性可以提高沸石对四环素的吸附能力。天然和改性沸石对四环素的吸附符合拟二级动力学模型,颗粒内扩散不是吸附过程的主要控制步骤。Freundlich和Dubinin-Radushkevich(D-R)等温吸附模型可以较好地描述实验所用2种沸石对四环素的吸附行为,D-R等温方程拟合结果显示吸附过程包含离子交换作用。通过对天然和改性沸石吸附四环素前后溶液中主要阳离子浓度变化分析证实了该吸附过程包含离子交换作用。实验研究了pH值变化对沸石吸附四环素的影响,当pH=3～5时,天然和改性沸石对四环素的吸附量均随pH值的增加而急剧下降,而pH=5～10时,天然和改性沸石对四环素的吸附量变化均不明显,推测可能是离子交换作用和化学沉淀吸附作用所致。另外,实验还初步探索了溶液离子强度对沸石吸附四环素的影响情况,随着溶液中Na+和Ca2+离子强度的增加,吸附量先急剧降低随后趋向平稳,进一步说明了沸石对四环素的吸附过程不是由单一机制控制的。     

厌氧颗粒污泥藻酸盐对铜离子的吸附研究

从厌氧颗粒污泥中成功提取出细菌藻酸盐并制备成藻酸钙吸附剂,研究其对水中Cu~(2+)的吸附性能。实验结果表明,接触时间、Cu~(2+)初始浓度和溶液初始pH是影响Cu~(2+)吸附性能的重要因素。吸附等温线研究表明,Langmuir模型比Freundlich模型能更好地描述吸附过程。Cu~(2+)在藻酸钙上的吸附动力学过程可以很好地用Pseudo二级动力学方程来描述。以100 mmol/L HCI为解吸剂,可有效洗脱藻酸钙上95%的Cu~(2+),实现Cu~(2+)的回收。     

Adsorption of 2,4-dichlorophenoxyacetic acid and 4-chloro-2-metylphenoxyacetic acid onto activated carbons derived from various lignocellulosic materials

Adsorption of 2,4-dichlorophenoxyacetic acid (2,4-D) and 4-chloro-2-metylphenoxyacetic acid (MCPA) from aqueous solution onto activated carbons derived from various lignocellulosic materials including willow, miscanthus, flax, and hemp shives was investigated. The adsorption kinetic data were analyzed using two kinetic models: the pseudo-first order and pseudo-second order equations. The adsorption kinetics of both herbicides was better represented by the pseudo-second order model. The adsorption isotherms of 2,4-D and MCPA on the activated carbons were analyzed using the Freundlich and Langmuir isotherm models. The equilibrium data followed the Langmuir isotherm. The effect of pH on the adsorption was also studied. The results showed that the activated carbons prepared from the lignocellulosic materials are efficient adsorbents for the removal of 2,4-D and MCPA from aqueous solutions.     

Biosorption characteristics of copper (II), chromium (III), nickel (II), and lead (II) from aqueous solutions by Chara sp. and Cladophora sp.

The aim of this research was to expose individual removals of copper, chromium, nickel, and lead from aqueous solutions via biosorption using nonliving algae species, Chara sp. and Cladophora sp. Optimum pH values for biosorption of copper (II), chromium (III), nickel (II), and lead (II) from aqueous solutions were determined to be 6, 7, 7, and 3 for Cladophora sp. and 5, 3, 5, and 4 for Chara sp. respectively. Maximum adsorption capacities of Chara sp. [10.54 for chromium (III) and 61.72 for lead (II)] and Cladophora sp. [6.59 for chromium (III) and 16.75 and 23.25 for lead (II)] for chromium (III) and lead (II) are similar. On the other hand, copper (II) and nickel (II) biosorption capacity of Cladophora sp. [14.28 for copper (II) and 16.75 for nickel (II)] is greater than Chara sp. [6.506 for copper (II) and 11.76 for nickel (II)]. Significantly high correlation coefficients indicated for the Langmuir adsorption isotherm models can be used to describe the equilibrium behavior of copper, chromium, nickel, and lead adsorption onto Cladophora sp. and Chara sp.     

In vitro study of oxytetracycline adsorption on activated charcoal

In vitro adsorption experiments simulating pH in gastric environment and using Langmuir isotherm, showed that 408 mg of oxytetracycline was adsorbed per gram of activated charcoal. Langmuir isotherm fitted adsorption data better than a Freundlich isotherm. Freundlich isotherm showed a specific adsorption capacity of 518 mg/g for activated charcoal. Both isotherm parameters indicated a strong oxytetracycline adsorption on activated charcoal in terms of quantity and binding strength. The results demonstrate that the concomitant use of oxytetracyline and activated charcoal should be avoided.