Fast preparation of the seawater accommodated fraction of heavy fuel oil by sonication

The seawater accommodated fraction (SWAF) of oil is widely used for the assessment of its toxicity. However, its preparation in the laboratory is time consuming, and results from different authors are difficult to compare as preparation methods vary. Here we describe a simple and fast set up, using sonication, to produce reproducible SWAF in the laboratory. The system was tested on heavy fuel oil placed on seawater at different salinity and temperature conditions. Maximum dissolution of the oil was achieved after 24 h, independently of both seawater salinity and temperature. Our findings are discussed in relation to the fate of the oil from the deep spill of the Prestige tanker. Changes in temperature in the open ocean are bound to have larger impact in the concentration of the SWAF than the corresponding values of sea water salinity. We anticipate that in this type of incident the highest SWAF, as the oil reaches the sea surface, should be expected in the warmest and less saline waters of the water column.     

Gladius and its derivatives as potential biosorbents for marine diesel oil

The demand for low cost and effective materials to remove contaminants such as residues of oil spills has encouraged studies on new biosorbents produced from wastes. Considering the overgeneration of fishing residues and the necessity to provide an alternative purpose for such materials, this study aimed to evaluate squid gladius and its derivatives (β-chitin and chitosan) as sorbents to remove marine diesel oil (MDO) from fresh and artificial seawater. It was also executed an attempted to improve their performances through a high-intensity ultrasound treatment (UT-gladius and UT-β-chitin). All sorbents removed MDO at both salinities. Contact surface area, salinity, and water retention seemed to play a key role in the outcomes. UT-β-chitin’s performance was significantly superior to β-chitin’s and chitosan’s in MDO removal at salinity 0, as well as at salinity 30, where gladius and UT-gladius also excelled. Ultrasound treatment improved the oil removal performance of UT-β-chitin by increasing its contact surface area. This is the first report on the efficiency of gladius and UT-β-chitin for such purpose, and brought up huge possibilities and new questions that can lead to the achievement of biosorbents of great efficiency.     

改善深圳河水质的补水方案及生态影响初步分析

深圳河旱季天然径流量小而污染负荷高,为了改善河流水质,在削减入河污染物的同时有必要采取补水措施。利用水质模型,计算了不同污水处理率下,分别以污水资源化再生水、珠江口海水和大鹏湾海水为补水水源时,深圳河达到基本不黑臭所需的补水量。讨论了补水方案对河流水质、盐度、水动力条件的改变及其对生态系统的影响。研究表明,引海水对河流生态系统的冲击不容忽视。而污水资源化是较优的补水方案。     

Seasonal and local variation of Cr, Ni and Co concentrations in Ulva rigida C. Agardh and Enteromorpha linza (Linnaeus) from Thermaikos Gulf, Greece

Cobalt, nickel and chromium concentrations were determined in Enteromorpha linza and Ulva rigida in seawater and sediment after seasonal collection from Thermaikos Gulf, Greece. Industrial waste and sewage is poured into this Gulf. The relative abundance of metals in the seaweeds and seawater decreased in the order Ni > Cr > Co, whereas in the sediment the order was Cr > Ni > Co. The two seaweeds bioaccumulated similar metal concentrations. The seasonal variation of metals in the two algae was not significant, but seemed to depend on the growth dynamics, the age of the tissue, the metal concentrations in the environment and the abiotic factors (such as salinity and temperature). Only Cr concentrations in E. linza showed significant local variation which depended on the area into which the industrial and domestic wastes were discharged and on their transport by sea currents. Nickel and chromium concentrations in U. rigida and Cr concentrations in E. linza displayed significant positive correlation with their concentrations in the seawater. Concentrations of the three metals in the seaweeds and seawater of Thermaikos Gulf generally exceeded the 'background' levels.     

Factors affecting photooxidation of oil constituents in the marine environment. I. Photochemical transformations of dimethylnaphthalenes in an aqueous environment in the presence and absence of oil

Photooxidation studies of 1,3-, 1,4-, 1,8- and 2,3-dimethylnaphthalene (DMN) suspended in and layered on seawater and distilled water have been performed in the presence and absence of crude Ekofisk oil, methylene blue and dibenzothiophene. With the exception of 2,3-DMN which was very insensitive to the reaction conditions, the course of reaction was, generally, influenced by the structure of the substrate, the salinity of the water, the oil and the presence of sulfur-containing compounds. In the absence of oil the photooxidation was fairly inefficient and took place exclusively in benzylic positions. In the presence of oil oxidation of the naphthalene moiety predominated due to abundant formation of singlet oxygen.     

Toxicity of acid-sulphate soil leachate and aluminium to the embryos and larvae of Australian bass (Macquaria novemaculeata) in estuarine water

The toxicity of leachate water from acid-sulphate soil to the early life stages of Australian bass, Macquaria novemaculeata, incubated in seawater was evaluated. Acid-sulphate soil leachate water (pH> or =6.8) delayed the hatching of fertilised eggs, but after 48 h the per cent hatching was normal. In comparison, acidic saline water (25 per thousand salinity) at pH 4.0 or less prevented embryos from hatching. The survival of yolk-sac larvae exposed to acid-sulphate soil leachate water at a concentration of 32% in seawater and an initial pH of 7.2, was significantly different to controls after 96 hours. In corresponding tests with only acidified saline water (20 per thousand salinity), pH levels equal to or below 5.0 killed yolk-sac larvae after 96 h exposure. Aluminum showed a pH dependent toxicity to yolk-sac larvae, with added aluminium as low as 200 microg litre(-1) having a significant effect on larval survival at pH 5.5, and concentrations of 600-800 microg litre(-1) having a significant effect on larval survival at an initial pH range of 6.0 < pH < 6.8. It was concluded that significant mortality of the early life stages of Australian bass would occur if they are exposed to acid-sulphate soil leachate that results in a pH in the receiving estuarine water below 5.5, or when the pH is below 6.8 and aluminium is present at a total concentration of 800 microg litre(-1) or greater.     

Effect of water pH and salinity on the survival of eggs and larvae of the euryhaline teleost, Gasterosteus aculeatus L

The effect of water acidification and salinity on the survival of the eggs and larvae of the euryhaline teleost, Gasterosteus aculeatus, was studied using tap water that was low in calcium and high in total aluminium as the basic medium. The survival of eggs from fertilisation to hatching increased with an increase in pH from 4.5 to 6.5. Survival was higher at a given pH at higher salinities (equivalent to 5% and 10% seawater) than in tap water. The salinity experienced by the female prior to spawning also had an effect on egg survival. Survival for 7 days after hatching was high except at the lowest pH levels. The salinity experienced by the female had no significant effect on larval survival.     

The adsorption behaviour of dimethyltin from seawater onto sedimentary phase in Tianjin Harbor

The adsorption of dimethyltin from a seawater matrix onto suspended particulate matter was studied. The influences of pH and salinity, adsorption isotherms at various temperatures, and the adsorption rate under certain experimental conditions were determined. It was found that the adsorption capacity was highest at c. pH 6 and decreased with increasing salinity. The adsorption behaviour at various temperatures was described best by a Langmuir isotherm. The adsorption capacity of dimethyltin was higher in natural seawater than in artificial seawater at the same temperature.     

pH对污水污泥中污染物浸出的影响

研究pH对污泥中污染物浸出的影响可以为投海过程中海洋水体酸碱性变化对污泥中污染物浸出的影响及其变化规律提供理论依据。为了得出不同pH值对污泥中污染物浸出的影响,采用CEN/TS 14429：2005浸出实验对上海5个污水处理厂脱水污泥中重金属、溶解性有机碳、溶解性硫化物和主要离子的浸出情况进行了研究,同时分别以超纯水和海水为浸提剂研究在相应pH范围内盐度对上述指标浸出的影响。结果表明,Zn、Cd、Pb和As在酸性和碱性条件下浸出量较高,在中性或接近中性条件下浸出量则最低,且海水中Zn和Cd的浸出量比超纯水中高;Cu在碱性条件下的浸出量明显比酸性条件高;在所研究的pH范围内,5个污泥样品中溶解性有机碳的浸出量均随pH的升高而增高;仅酸挥发性硫含量最高的S5在海水中有较明显的溶解性硫化物浸出;部分污泥样品中的氮在酸性纯水中有较高的浸出量,海水中浸出量较少;而无论海水或纯水中,磷在强酸和强碱条件下均有明显浸出。     

Studies on the sorption behaviors of nitrobenzene on marine sediments

The sorption behaviors of nitrobenzene on marine sediments were systematically investigated in this study. The nitrobenzene sorption on both HCl-treated and untreated sediments accorded well with the linear sorption isotherm. It occurred primarily through partition function of organic carbon of sediments. In comparison, the sorption behavior of nitrobenzene on H2O2-treated sediments was nonlinear and conformed to Langmuir isotherm. Sorption of nitrobenzene on H2O2-treated sediment was mainly through surface function of sediment minerals such as clays. With the increase of ionic strength (salinity), solubility of nitrobenzene in solution would decrease. At the same time, the release of dissolvable part of organic carbon into water solution would also decrease. As a result, partition coefficient and saturate adsorption amount of nitrobenzene on marine sediments increased with increasing salinity of seawater. Contrary to the influence of salinity, partition coefficient and saturate adsorption amount of nitrobenzene decreased with increasing temperature.     

Influence of salinity and temperature on the activity of biosurfactants by polychaete-associated isolates

Influence of different parameters on biosurfactant (BS) activity was carried out on strains that were isolated from the polychaetes Megalomma claparedei, Sabella spallanzanii and Branchiomma luctuosum and additional 30 strains that were previously identified as potential BS producers from crude oil enrichments of the same polychaete specimens. The selection of BS-producing strains from polychaete natural samples was carried out by using standard screening tests. The BS activity by each isolate was evaluated for the effect of salinity and temperature on emulsion production and surface tension reduction, during incubation in mineral medium supplemented with tetradecane or diesel oil. All isolates showed a similar time course of BS activity, and the latter was more influenced by salinity rather than temperature. Some of the BS producers belonged to genera that have not (i.e. Citricoccus, Cellulophaga, Tenacibaculum and Maribacter) or have poorly been (Psychrobacter, Vibrio, and Pseudoalteromonas) reported as able to produce BSs. This is remarkable as some of them have previously been detected in hydrocarbon-enriched samples. Results confirm that filter-feeding polychaetes are an efficient source for the isolation of BS producers.     

Removal by sorption and in situ biodegradation of oil spills limits damage to marine biota: a laboratory simulation

This study examined the efficiency of cotton grass fibers in removing diesel oil from the surface of water in conditions prevailing in the Baltic Sea. The effect of low temperature, salinity, and bacterial amendments were tested in laboratory-scale set-ups, whereas 600-L mesocosms filled with Baltic Sea water were used for testing the effects of diesel oil and rapid removal of the oil on microorganisms, phytoplankton, and mussels. Cotton grass proved to be an excellent sorbent for diesel oil from the water surface at a low temperature. Inoculation with diesel-enriched microorganisms enhanced degradation of oil significantly in laboratory-scale experiments. In mesocosm experiments, the addition of diesel oil (0.66 mg L(-1), 0.533 L m(-2)) to the basins resulted in higher microbial density than in all other basins, including inoculated ones, suggesting that the Baltic Sea contains indigenous hydrocarbon degraders. The removal of oil with cotton grass significantly improved the survival of mussels in the mesocosm tests: 100% mortality in diesel basins versus 0% mortality in basins with cotton grass, respectively. However, the surviving mussels suffered from histopathological changes such as inflammatory responses, degenerations, and cell death. The observed rescuing effect was observable even when the cotton grass-bound oil was left in the water. The results underline the importance of rapid action in limiting damage caused by oil spills.     

Study on the raw fish oil purification from PCDD/F and dl-PCB-industrial tests

The results of tests for the purification of fish oils with activated carbon for industrial use are presented. The optimum parameters for the process of purification (granulation of the activated carbon, its dosage, the oil temperature, and the duration of mixing the oil with activated carbon) were previously established for the laboratory scale. The optimization of the process consisted of selecting purification parameters that would allow for maximum reduction of the toxic polychlorinated dibenzo-para-dioxins and polychlorinated dibenzofurans (PCDD/Fs) content, while retaining the favorable high fatty acid content [C20:5 n−3, eicosapentaenoic acid (EPA) and C22:6 n−3, docosahexaenoic acid (DHA)]. The use of that optimum parameters in industrial conditions confirmed the satisfactory results obtained in laboratory tests. Five types of oil derived from various Baltic fish were purified. Reduction in the PCDD/Fs content was 77.0–93.6% on average, whereas in the dioxin-like polychlorinated biphenyls (dl-PCBs)—it was 42.7–50.5% on average, with insignificant changes in the total amount of EPA and DHA content. Furthermore, a significant reduction in the content of arsenic was noted (by about 62% on average), with insignificant changes in the content of organochlorine pesticides (OCPs), and marker polychlorinated biphenyls (PCBs), polybrominated diphenyl ethers (PBDEs), cadmium, lead, and mercury.Purification provided fish oil having standardized parameters that allow for its use as feed additives, whilst retaining its favorable fatty acid content.     

Assessment of crude oil biodegradation in arctic seashore sediments: effects of temperature,salinity, and crude oil concentration

The expected increase in offshore oil exploration and production in the Arctic may lead to crude oil spills along arctic shorelines. To evaluate the potential effectiveness of bioremediation to treat such spills, oil spill bioremediation in arctic sediments was simulated in laboratory microcosms containing beach sediments from Barrow (Alaska), spiked with North Slope Crude, and incubated at varying temperatures and salinities. Biodegradation was measured via respiration rates (CO₂ production); volatilization was quantified by gas chromatography/mass spectrophotometry (GC/MS) analysis of hydrocarbons sorbed to activated carbon, and hydrocarbons remaining in the sediment were quantified by GC/flame ionization detector (FID). Higher temperature leads to increased biodegradation by naturally occurring microorganisms, while the release of volatile organic compounds was similar at both temperatures. Increased salinity had a small positive impact on crude oil removal. At higher crude oil dosages, volatilization increased, however CO₂ production did not. While only a small percentage of crude oil was completely biodegraded, a larger percentage was volatilized within 6–9 weeks.     

Rapid and Sensitive LC/MS/MS Direct Injection Method for the Determination of Trace Level Corexit EC9500A Oil Dispersant in Seawater

A rapid and sensitive liquid chromatography tandem mass spectrometry (LC/MS/MS) method for the determination of trace dioctyl sulfosuccinate (DOSS) concentrations in seawater samples has been established. The method is well suited to aquatic environment impact monitoring following application of the dispersant Corexit EC9500A. Linearity of the method was demonstrated down to 0.05 ng/mL^?1 (0.05 µgL^?1) DOSS in seawater, with a 2.4% relative standard deviation precision for preparation replicates. A US EPA method limit of detection of <0.02 ng/mL^?1 (<0.02 µgL^?1) was calculated and specificity was confirmed by monitoring of two qualifier ions at 291.1 m/z and 227.1 m/z. These transitions were confirmed by QToF analysis to be associated with the DOSS precursor ion at 421.2 m/z. For application to seawater samples and samples containing oil particulates, a practical and repeatable calibration range of 0.5 ng/mL^?1 (0.5 µgL^?1) to 25.0 ng/mL^?1 (25.0 µgL^?1) DOSS is reported. The method was shown to have excellent precision and accuracy, with a consistent ≤1.6% relative standard deviation for system suitability standards at 0.5 ng/mL^?1 (0.5 µgL^?1) and linear weighted (1/x) regression coefficients of determination ≥0.995. The surfactant nature of the analyte is discussed in relation to detection limit and loss of analyte. Speculation of a relationship between DOSS in association or aggregation with divalent cations, such as Ca²⁺ present in salt water and hard water, is suggested. The consequent effects on cell ionic balance and membrane function are discussed.     

絮凝-微纳气泡法处理采油废水

对采自胜利油田的采油废水,分别进行了聚硅硫酸铁(PFSS)絮凝法、微纳气泡法和絮凝-微纳气泡联合法处理,考察了处理过程对采油废水水质和所配制聚合物(部分水解聚丙烯酰胺)溶液粘度的影响。结果表明,均可有效降低废水的矿化度、油含量和悬浮物含量,明显提高用其配制的聚合物溶液的粘度;联合处理效果明显高于单独采用絮凝或微纳气泡处理的效果。所处理后的废水可有望代替淡水用于油田现场配制聚合物驱油体系,在消除油田污水环境污染的同时,可节约淡水资源。     

Crude oil contaminated soil washing in air sparging assisted stirred tank reactor using biosurfactants

This study investigated the removal of crude oil from soil using air sparging assisted stirred tank reactors. Two surfactants (rhamnolipid and sodium dodecyl sulfate, SDS) were tested and the effects of different parameters (i.e. temperature, surfactant concentrations, washing time, volume/mass ratio) were investigated under varying washing modes namely, stirring only, air sparging only and the combination of stirring and air sparging. The results showed that SDS removed more than 80% crude oil from non-weathered soil samples, whilst rhamnolipid showed similar oil removal at the third and fourth levels of the parameters tested. The oil removal ability of the seawater prepared solutions were better than those of the distilled water solutions at the first and second levels of temperature and concentration of surfactant solutions. This approach of soil washing was noted to be effective in reducing the amount of oil in soil. Therefore we suggested that a field scale test be conducted to assess the efficiency of these surfactants.     

Arsenic Background Definition: Introduction and Objectives

Produced water samples from the Bacia de Campos oil field offshore Pargo and Pampo platforms were analyzed for Ba, 226 Ra, 228 Ra, V, Ni and Pb. The activity concentrations measured were in the range of 1.6-6.0 Bq/L for 226 Ra and 0.7-8.2 Bq/L for 228 Ra for both platforms. For Ba, V, Ni and Pb the concentrations measured were in the range of 5.6-25.7 mg/L, 0.15-0.46 µg/L, 4.85-12.14 µg/L and 4.04-12.37 µg/L. A strong correlation between barium and radium isotopes concentration was observed ( 226 Ra: R 2 = 0.897; 228 Ra: R 2 = 0.737). In order to evaluate the environmental impact from discharges of produced water into the sea, the seawater and sediment samples were collected at distances from 250 to 1000 m around the platforms. The seawater samples were analyzed for dissolved and particulate material and the sediment samples for total and leachable fraction. The results show that even for the shortest sampling distance (250 m) from the discharge point, Ba, 226 Ra, 228 Ra, V, Ni and Pb concentrations in seawater and sediment were similar to the local background, indicating that dispersion by local currents minimizes any environmental impact involving these parameters.     

Oil spill response capabilities and technologies for ice-covered Arctic marine waters: A review of recent developments and established practices

Renewed political and commercial interest in the resources of the Arctic, the reduction in the extent and thickness of sea ice, and the recent failings that led to the Deepwater Horizon oil spill, have prompted industry and its regulatory agencies, governments, local communities and NGOs to look at all aspects of Arctic oil spill countermeasures with fresh eyes. This paper provides an overview of present oil spill response capabilities and technologies for ice-covered waters, as well as under potential future conditions driven by a changing climate. Though not an exhaustive review, we provide the key research results for oil spill response from knowledge accumulated over many decades, including significant review papers that have been prepared as well as results from recent laboratory tests, field programmes and modelling work. The three main areas covered by the review are as follows: oil weathering and modelling; oil detection and monitoring; and oil spill response techniques.